| Age | Commit message (Collapse) | Author |
|---|
|
A BAR size is always a power of two. buf_size = min(SZ_1M, bar_size).
If the BAR size is <= 1MB, there will be one iteration, no remainder.
If the BAR size is > 1MB, there will be more than one iteration, but the
size will always be evenly divisible by 1MB, so no remainder.
Link: https://lore.kernel.org/r/20250109094556.1724663-2-18255117159@163.com
Suggested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add a more advanced BAR test that writes all BARs in one go, and then reads
them back and verifies that the value matches the BAR number bitwise OR'ed
with offset, this allows us to verify:
- The BAR number was what we intended to read
- The offset was what we intended to read
This allows us to detect potential address translation issues on the EP.
Reading back the BAR directly after writing will not allow us to detect the
case where inbound address translation on the endpoint incorrectly causes
multiple BARs to be redirected to the same memory region (within the EP).
Link: https://lore.kernel.org/r/20241116032045.2574168-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The test BAR is on the EP side is allocated using pci_epf_alloc_space(),
which allocates the backing memory using dma_alloc_coherent(), which will
return zeroed memory regardless of __GFP_ZERO was set or not.
This means that running a new version of pci-endpoint-test.c (host side)
with an old version of pci-epf-test.c (EP side) will not see any
capabilities being set (as intended), so this is backwards compatible.
Additionally, the EP side always allocates at least 128 bytes for the test
BAR (excluding the MSI-X table), this means that adding another register at
offset 0x30 is still within the 128 available bytes.
For now, we only add the CAP_UNALIGNED_ACCESS capability.
If CAP_UNALIGNED_ACCESS is set, that means that the EP side supports
reading/writing to an address without any alignment requirements.
Thus, if CAP_UNALIGNED_ACCESS is set, make sure that the host side does
not add any extra padding to the buffers that we allocate (which was only
done in order to get the buffers to satisfy certain alignment requirements
by the endpoint controller).
Link: https://lore.kernel.org/r/20241203063851.695733-6-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
The test BAR is on the EP side is allocated using pci_epf_alloc_space(),
which allocates the backing memory using dma_alloc_coherent(), which will
return zeroed memory regardless of __GFP_ZERO was set or not.
This means that running a new version of pci-endpoint-test.c (host side)
with an old version of pci-epf-test.c (EP side) will not see any
capabilities being set (as intended), so this is backwards compatible.
Additionally, the EP side always allocates at least 128 bytes for the test
BAR (excluding the MSI-X table), this means that adding another register at
offset 0x30 is still within the 128 available bytes.
For now, we only add the CAP_UNALIGNED_ACCESS capability.
Set CAP_UNALIGNED_ACCESS if the EPC driver can handle any address (because
it implements the .align_addr callback).
Link: https://lore.kernel.org/r/20241203063851.695733-5-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
Currently, if DMA MEMCPY test is requested by the host, and if the endpoint
DMA controller supports DMA_PRIVATE, the test will fail. This is not
correct since there is no check for DMA_MEMCPY capability and the DMA
controller can support both DMA_PRIVATE and DMA_MEMCPY.
Fix the check and also reword the error message.
Link: https://lore.kernel.org/r/20250116171650.33585-2-manivannan.sadhasivam@linaro.org
Fixes: 8353813c88ef ("PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities")
Reported-by: Niklas Cassel <cassel@kernel.org>
Closes: https://lore.kernel.org/linux-pci/Z3QtEihbiKIGogWA@ryzen
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
If dma_chan_tx allocation fails, set dma_chan_rx to NULL after it is
freed.
Link: https://lore.kernel.org/r/20241227160841.92382-1-khalfella@gmail.com
Fixes: 8353813c88ef ("PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities")
Signed-off-by: Mohamed Khalfella <khalfella@gmail.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Changing voltage might ignore slew rate and cause a current surge.
With current implementation the driver will get the regulator to change
the voltage range used during run time. According to communication I
have had with Texas Instruments, this is not intended, since the
Dynamic Voltage Scaling in the hardware is only designed to work
within a voltage range. The current implementation will therefore
ignore the slew rate that is defined in devicetree when the voltage
range is changed during use.
The current implementation will always select a voltage in the most
accurate range that can reach that voltage even though multiple ranges
are able to reach that voltage. There are 4 Voltage ranges with the
following reach:
0b00: 0.4-0.71875V (1.25mV step size)
0b01: 0.4-1.0375V (2.5mV)
0b10: 0.4-1.675V (5mV)
0b11: 0.8-3.3V (10mV)
This in practice means that a change from below to above 0.71875V will
use the smallest range(0b00) for the values below and the second
smallest range(0b01) for the voltages above (Up to 1.675V). I have
timed how long it takes to go from below 0.71875V to above. The
increase was 100mV which, with the slew rate set to 1250µV/µs. This
in theory should take 80µs to do. With the current implementation, it
takes 10µs on my hardware. Doing the same test with the slew rate set
to 5000µV/µs, which should take 20µs, also only takes 10µs to do on
my hardware. Not only is this not in line with the technical
specification for the regulator. It also causes a current surge. Which
when calculating the output current, as described in the technical
specification, compared to what I could observe on my hardware the real
output is ~1A higher (~1.2A) than what I calculated it to be(~0.2A).
I tested also transitioning from a bigger to a smaller range, and the
results were the same.
Instead, let's limit the voltage range to a single one, which is in
line with the intended use of the regulator. This is done by looking
up the minimum and maximum requested voltage specified in devicetree.
Signed-off-by: Jonas Andreasson <jonas.andreasson@axis.com>
Link: https://patch.msgid.link/20250121-tps-fix-v2-1-50cc4d0f1635@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Shixiong Ou <oushixiong@kylinos.cn>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
devm_clk_get_optional() returns NULL for missing clocks and a PTR_ERR()
if there is a clock but we fail to get it, but currently we only handle
the latter case and do so as though the clock was missing. If we get an
error back we should handle that as an error since the clock exists but
we failed to get it, if we get NULL then the clock doesn't exist and we
should handle that.
Fixes: 4c6ac5446d06 ("spi: omap2-mcspi: Fix the IS_ERR() bug for devm_clk_get_optional_enabled()")
Reported-by: Lars Pedersen <lapeddk@gmail.com>
Link: https://patch.msgid.link/20250117-spi-fix-omap2-optional-v1-1-e77d4ac6db6e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lars Pedersen <lapeddk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both kcryptd_io_read() and kcryptd_crypt_write_convert() will invoke
crypt_alloc_buffer() to allocate a new bio. Both of these two callers
initialize bi_iter.bi_sector for the new bio separatedly after
crypt_alloc_buffer() returns. However, kcryptd_crypt_write_convert()
will copy the bi_iter of the new bio into ctx.iter_out or ctx.iter_in.
Although it doesn't incur any harm now, it is better to fully initialize
bi_iter before it is used.
Therefore, initialize bi_iter.bi_sector in crypt_alloc_buffer() instead.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Both kcryptd_crypt_write_continue() and kcryptd_crypt_read_continue()
are running in the kworker context, it is OK to call cond_resched(),
Therefore, set atomic as false when invoking crypt_convert() under
kworker context.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Merged the 'fixes' branch into the 'for-next' branch to resolve
a conflict in alienware-wmi zone teardown code.
|
|
When testing on my tiled display, initially the tiled display is
detected correctly:
[90376.523692] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] fallback: Not all outputs enabled
[90376.523713] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] Enabled: 0, detected: 2
...
[90376.523967] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:82:pipe A] desired mode 1920x2160 set (1920,0)
[90376.524020] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:134:pipe B] desired mode 1920x2160 set (0,0)
But then, when modes have been set:
[90379.729525] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] [CONNECTOR:287:DP-4] on [CRTC:82:pipe A]: 1920x2160
[90379.729640] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] [CONNECTOR:289:DP-5] on [CRTC:134:pipe B]: 1920x2160
...
[90379.730036] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:82:pipe A] desired mode 1920x2160 set (0,0)
[90379.730124] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:134:pipe B] desired mode 1920x2160 set (0,0)
Call drm_client_get_tile_offsets() in drm_client_firmware_config() as
well, to ensure that the offset is set correctly.
This has to be done as a separate pass, as the tile order may not be
equal to the drm connector order.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116142825.3933-2-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Cc: <stable@vger.kernel.org>
|
|
Tiled displays have a different x/y offset to begin with. Instead of
attempting to remember this, just apply a delta instead.
This fixes the first tile being duplicated on other tiles when vt
switching.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116142825.3933-1-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Cc: <stable@vger.kernel.org>
|
|
A specific allocation for the CRTC is not strictly necessary at this
point, but in order to implement dynamic configuration of VKMS (configFS),
it will be easier to have one allocation per CRTC.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250117-b4-vkms-allocated-v4-3-8ec8fd21aaf6@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
A specific allocation for the encoder is not strictly necessary at this
point, but in order to implement dynamic configuration of VKMS (configFS),
it will be easier to have one allocation per encoder.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250117-b4-vkms-allocated-v4-2-8ec8fd21aaf6@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
A specific allocation for the connector is not strictly necessary
at this point, but in order to implement dynamic configuration of
VKMS (configFS), it will be easier to have one allocation per
connector.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250117-b4-vkms-allocated-v4-1-8ec8fd21aaf6@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
The use of R7 in the SMCCC conflicts with the compiler's use of R7 as a frame
pointer in Thumb2 mode, which is forcibly enabled by Clang when profiling
hooks are inserted via the -pg switch.
This is a known issue and similar driver workaround this with a Makefile
ifdef. Exact workaround are applied in
drivers/firmware/arm_scmi/transports/Makefile and other similar driver.
Suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501201840.XmpHXpQ4-lkp@intel.com/
Fixes: 82e703dd438b ("pmdomain: airoha: Add Airoha CPU PM Domain support")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20250120153817.11807-1-ansuelsmth@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The current VKMS driver uses non-managed function to create
writeback connectors. It is not an issue yet, but in order
to support multiple devices easily, convert this code to
use drm and device managed helpers.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-8-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
To allows driver to only use drmm objects, add helper to create
drm_writeback_connectors with automated lifetime management.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-7-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
The current implementation of drm_writeback_connector initialization does
not properly clean up all resources in case of failure (allocated
properties and possible_encoders). Add this cleaning in case of failure.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-6-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
As the old drm and the new drmm variants of drm_writeback_connector
requires almost the same initialization, create an internal helper to do
most of the initialization work.
Currently there is no cleanup function for writeback connectors. To allows
implementation of drmm variant of writeback connector, create a cleanup
function that can be used to properly remove all the writeback-specific
properties and allocations.
This also introduce an helper to cleanup only the drm_writeback_connector
properties, so it can be used during initialization to cleanup in case of
failure.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-5-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
The current VKMS driver uses managed function to create crtc, but
don't use it to properly clean the crtc workqueue. It is not an
issue yet, but in order to support multiple devices easily,
convert this code to use drm and device managed helpers.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-4-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
Add drmm_alloc_ordered_workqueue(), a helper that provides managed ordered
workqueue cleanup. The workqueue will be destroyed with the final
reference of the DRM device.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-3-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
The current VKMS driver uses non-managed function to create encoders. It
is not an issue yet, but in order to support multiple devices easily,
convert this code to use drm and device managed helpers.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-2-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
The current VKMS driver uses non-managed function to create connectors. It
is not an issue yet, but in order to support multiple devices easily,
convert this code to use drm and device managed helpers.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-1-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
No conflicts and no adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Madhavan Srinivasan:
- Add preempt lazy support
- Deprecate cxl and cxl flash driver
- Fix a possible IOMMU related OOPS at boot on pSeries
- Optimize sched_clock() in ppc32 by replacing mulhdu() by
mul_u64_u64_shr()
Thanks to Andrew Donnellan, Andy Shevchenko, Ankur Arora, Christophe
Leroy, Frederic Barrat, Gaurav Batra, Luis Felipe Hernandez, Michael
Ellerman, Nilay Shroff, Ricardo B. Marliere, Ritesh Harjani (IBM),
Sebastian Andrzej Siewior, Shrikanth Hegde, Sourabh Jain, Thorsten Blum,
and Zhu Jun.
* tag 'powerpc-6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix argument order to timer_sub()
powerpc/prom_init: Use IS_ENABLED()
powerpc/pseries/iommu: IOMMU incorrectly marks MMIO range in DDW
powerpc: Use str_on_off() helper in check_cache_coherency()
powerpc: Large user copy aware of full:rt:lazy preemption
powerpc: Add preempt lazy support
powerpc/book3s64/hugetlb: Fix disabling hugetlb when fadump is active
powerpc/vdso: Mark the vDSO code read-only after init
powerpc/64: Use get_user() in start_thread()
macintosh: declare ctl_table as const
selftest/powerpc/ptrace: Cleanup duplicate macro definitions
selftest/powerpc/ptrace/ptrace-pkey: Remove duplicate macros
selftest/powerpc/ptrace/core-pkey: Remove duplicate macros
powerpc/8xx: Drop legacy-of-mm-gpiochip.h header
scsi/cxlflash: Deprecate driver
cxl: Deprecate driver
selftests/powerpc: Fix typo in test-vphn.c
powerpc/xmon: Use str_yes_no() helper in dump_one_paca()
powerpc/32: Replace mulhdu() by mul_u64_u64_shr()
|
|
Prepare input updates for 6.14 merge window.
|
|
When enabling a pass-through port an interrupt might come before psmouse
driver binds to the pass-through port. However synaptics sub-driver
tries to access psmouse instance presumably associated with the
pass-through port to figure out if only 1 byte of response or entire
protocol packet needs to be forwarded to the pass-through port and may
crash if psmouse instance has not been attached to the port yet.
Fix the crash by introducing open() and close() methods for the port and
check if the port is open before trying to access psmouse instance.
Because psmouse calls serio_open() only after attaching psmouse instance
to serio port instance this prevents the potential crash.
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: 100e16959c3c ("Input: libps2 - attach ps2dev instances as serio port's drvdata")
Link: https://bugzilla.suse.com/show_bug.cgi?id=1219522
Cc: stable@vger.kernel.org
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/Z4qSHORvPn7EU2j1@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Microsoft defined Meta+Shift+F23 as the Copilot shortcut instead of a
dedicated keycode, and multiple vendors have their keyboards emit this
sequence in response to users pressing a dedicated "Copilot" key.
Unfortunately the default keymap table in atkbd does not map scancode
0x6e (F23) and so the key combination does not work even if userspace
is ready to handle it.
Because this behavior is common between multiple vendors and the
scancode is currently unused map 0x6e to keycode 193 (KEY_F23) so that
key sequence is generated properly.
MS documentation for the scan code:
https://learn.microsoft.com/en-us/windows/win32/inputdev/about-keyboard-input#scan-codes
Confirmed on Lenovo, HP and Dell machines by Canonical.
Tested on Lenovo T14s G6 AMD.
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250107034554.25843-1-mpearson-lenovo@squebb.ca
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"We've got a little less than normal thanks to the holidays in
December, but there's the usual summary below. The highlight is
probably the 52-bit physical addressing (LPA2) clean-up from Ard.
Confidential Computing:
- Register a platform device when running in CCA realm mode to enable
automatic loading of dependent modules
CPU Features:
- Update a bunch of system register definitions to pick up new field
encodings from the architectural documentation
- Add hwcaps and selftests for the new (2024) dpISA extensions
Documentation:
- Update EL3 (firmware) requirements for booting Linux on modern
arm64 designs
- Remove stale information about the kernel virtual memory map
Miscellaneous:
- Minor cleanups and typo fixes
Memory management:
- Fix vmemmap_check_pmd() to look at the PMD type bits
- LPA2 (52-bit physical addressing) cleanups and minor fixes
- Adjust physical address space depending upon whether or not LPA2 is
enabled
Perf and PMUs:
- Add port filtering support for NVIDIA's NVLINK-C2C Coresight PMU
- Extend AXI filtering support for the DDR PMU on NXP IMX SoCs
- Fix Designware PCIe PMU event numbering
- Add generic branch events for the Apple M1 CPU PMU
- Add support for Marvell Odyssey DDR and LLC-TAD PMUs
- Cleanups to the Hisilicon DDRC and Uncore PMU code
- Advertise discard mode for the SPE PMU
- Add the perf users mailing list to our MAINTAINERS entry"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (64 commits)
Documentation: arm64: Remove stale and redundant virtual memory diagrams
perf docs: arm_spe: Document new discard mode
perf: arm_spe: Add format option for discard mode
MAINTAINERS: Add perf list for drivers/perf/
arm64: Remove duplicate included header
drivers/perf: apple_m1: Map generic branch events
arm64: rsi: Add automatic arm-cca-guest module loading
kselftest/arm64: Add 2024 dpISA extensions to hwcap test
KVM: arm64: Allow control of dpISA extensions in ID_AA64ISAR3_EL1
arm64/hwcap: Describe 2024 dpISA extensions to userspace
arm64/sysreg: Update ID_AA64SMFR0_EL1 to DDI0601 2024-12
arm64: Filter out SVE hwcaps when FEAT_SVE isn't implemented
drivers/perf: hisi: Set correct IRQ affinity for PMUs with no association
arm64/sme: Move storage of reg_smidr to __cpuinfo_store_cpu()
arm64: mm: Test for pmd_sect() in vmemmap_check_pmd()
arm64/mm: Replace open encodings with PXD_TABLE_BIT
arm64/mm: Rename pte_mkpresent() as pte_mkvalid()
arm64/sysreg: Update ID_AA64ISAR2_EL1 to DDI0601 2024-09
arm64/sysreg: Update ID_AA64ZFR0_EL1 to DDI0601 2024-09
arm64/sysreg: Update ID_AA64FPFR0_EL1 to DDI0601 2024-09
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- Use the generic muldi3 libgcc function
- Miscellaneous fixes and improvements
* tag 'm68k-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: libgcc: Fix lvalue abuse in umul_ppmm()
m68k: vga: Fix I/O defines
zorro: Constify 'struct bin_attribute'
m68k: atari: Use str_on_off() helper in atari_nvram_proc_read()
m68k: Use kernel's generic muldi3 libgcc function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Alexander Gordeev:
- Select config option KASAN_VMALLOC if KASAN is enabled
- Select config option VMAP_STACK unconditionally
- Implement arch_atomic_inc() / arch_atomic_dec() functions which
result in a single instruction if compiled for z196 or newer
architectures
- Make layering between atomic.h and atomic_ops.h consistent
- Comment s390 preempt_count implementation
- Remove pre MARCH_HAS_Z196_FEATURES preempt count implementation
- GCC uses the number of lines of an inline assembly to calculate
number of instructions and decide on inlining. Therefore remove
superfluous new lines from a couple of inline assemblies.
- Provide arch_atomic_*_and_test() implementations that allow the
compiler to generate slightly better code.
- Optimize __preempt_count_dec_and_test()
- Remove __bootdata annotations from declarations in header files
- Add missing include of <linux/smp.h> in abs_lowcore.h to provide
declarations for get_cpu() and put_cpu() used in the code
- Fix suboptimal kernel image base when running make kasan.config
- Remove huge_pte_none() and huge_pte_none_mostly() as are identical to
the generic variants
- Remove unused PAGE_KERNEL_EXEC, SEGMENT_KERNEL_EXEC, and
REGION3_KERNEL_EXEC defines
- Simplify noexec page protection handling and change the page, segment
and region3 protection definitions automatically if the instruction
execution-protection facility is not available
- Save one instruction and prefer EXRL instruction over EX in string,
xor_*(), amode31 and other functions
- Create /dev/diag misc device to fetch diagnose specific information
from the kernel and provide it to userspace
- Retrieve electrical power readings using DIAGNOSE 0x324 ioctl
- Make ccw_device_get_ciw() consistent and use array indices instead of
pointer arithmetic
- s390/qdio: Move memory alloc/pointer arithmetic for slib and sl into
one place
- The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that in s390 code
- Add missing TLB range adjustment in pud_free_tlb()
- Improve topology setup by adding early polarization detection
- Fix length checks in codepage_convert() function
- The generic bitops implementation is nearly identical to the s390
one. Switch to the generic variant and decrease a bit the kernel
image size
- Provide an optimized arch_test_bit() implementation which makes use
of flag output constraint. This generates slightly better code
- Provide memory topology information obtanied with DIAGNOSE 0x310
using ioctl.
- Various other small improvements, fixes, and cleanups
Also, some changes came in through a merge of 'pci-device-recovery'
branch:
- Add PCI error recovery status mechanism
- Simplify and document debug_next_entry() logic
- Split private data allocation and freeing out of debug file open()
and close() operations
- Add debug_dump() function that gets a textual representation of a
debug info (e.g. PCI recovery hardware error logs)
- Add formatted content of pci_debug_msg_id to the PCI report
* tag 's390-6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits)
s390/futex: Fix FUTEX_OP_ANDN implementation
s390/diag: Add memory topology information via diag310
s390/bitops: Provide optimized arch_test_bit()
s390/bitops: Switch to generic bitops
s390/ebcdic: Fix length decrement in codepage_convert()
s390/ebcdic: Fix length check in codepage_convert()
s390/ebcdic: Use exrl instead of ex
s390/amode31: Use exrl instead of ex
s390/stackleak: Use exrl instead of ex in __stackleak_poison()
s390/lib: Use exrl instead of ex in xor functions
s390/topology: Improve topology detection
s390/tlb: Add missing TLB range adjustment
s390/pkey: Constify 'struct bin_attribute'
s390/sclp: Constify 'struct bin_attribute'
s390/pci: Constify 'struct bin_attribute'
s390/ipl: Constify 'struct bin_attribute'
s390/crypto/cpacf: Constify 'struct bin_attribute'
s390/qdio: Move memory alloc/pointer arithmetic for slib and sl into one place
s390/cio: Use array indices instead of pointer arithmetic
s390/qdio: Rename feature flag aif_osa to aif_qdio
...
|
|
Pull io_uring updates from Jens Axboe:
"Not a lot in terms of features this time around, mostly just cleanups
and code consolidation:
- Support for PI meta data read/write via io_uring, with NVMe and
SCSI covered
- Cleanup the per-op structure caching, making it consistent across
various command types
- Consolidate the various user mapped features into a concept called
regions, making the various users of that consistent
- Various cleanups and fixes"
* tag 'for-6.14/io_uring-20250119' of git://git.kernel.dk/linux: (56 commits)
io_uring/fdinfo: fix io_uring_show_fdinfo() misuse of ->d_iname
io_uring: reuse io_should_terminate_tw() for cmds
io_uring: Factor out a function to parse restrictions
io_uring/rsrc: require cloned buffers to share accounting contexts
io_uring: simplify the SQPOLL thread check when cancelling requests
io_uring: expose read/write attribute capability
io_uring/rw: don't gate retry on completion context
io_uring/rw: handle -EAGAIN retry at IO completion time
io_uring/rw: use io_rw_recycle() from cleanup path
io_uring/rsrc: simplify the bvec iter count calculation
io_uring: ensure io_queue_deferred() is out-of-line
io_uring/rw: always clear ->bytes_done on io_async_rw setup
io_uring/rw: use NULL for rw->free_iovec assigment
io_uring/rw: don't mask in f_iocb_flags
io_uring/msg_ring: Drop custom destructor
io_uring: Move old async data allocation helper to header
io_uring/rw: Allocate async data through helper
io_uring/net: Allocate msghdr async data through helper
io_uring/uring_cmd: Allocate async data through generic helper
io_uring/poll: Allocate apoll with generic alloc_cache helper
...
|
|
Pull block updates from Jens Axboe:
- NVMe pull requests via Keith:
- Target support for PCI-Endpoint transport (Damien)
- TCP IO queue spreading fixes (Sagi, Chaitanya)
- Target handling for "limited retry" flags (Guixen)
- Poll type fix (Yongsoo)
- Xarray storage error handling (Keisuke)
- Host memory buffer free size fix on error (Francis)
- MD pull requests via Song:
- Reintroduce md-linear (Yu Kuai)
- md-bitmap refactor and fix (Yu Kuai)
- Replace kmap_atomic with kmap_local_page (David Reaver)
- Quite a few queue freeze and debugfs deadlock fixes
Ming introduced lockdep support for this in the 6.13 kernel, and it
has (unsurprisingly) uncovered quite a few issues
- Use const attributes for IO schedulers
- Remove bio ioprio wrappers
- Fixes for stacked device atomic write support
- Refactor queue affinity helpers, in preparation for better supporting
isolated CPUs
- Cleanups of loop O_DIRECT handling
- Cleanup of BLK_MQ_F_* flags
- Add rotational support for null_blk
- Various fixes and cleanups
* tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux: (106 commits)
block: Don't trim an atomic write
block: Add common atomic writes enable flag
md/md-linear: Fix a NULL vs IS_ERR() bug in linear_add()
block: limit disk max sectors to (LLONG_MAX >> 9)
block: Change blk_stack_atomic_writes_limits() unit_min check
block: Ensure start sector is aligned for stacking atomic writes
blk-mq: Move more error handling into blk_mq_submit_bio()
block: Reorder the request allocation code in blk_mq_submit_bio()
nvme: fix bogus kzalloc() return check in nvme_init_effects_log()
md/md-bitmap: move bitmap_{start, end}write to md upper layer
md/raid5: implement pers->bitmap_sector()
md: add a new callback pers->bitmap_sector()
md/md-bitmap: remove the last parameter for bimtap_ops->endwrite()
md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()
md: Replace deprecated kmap_atomic() with kmap_local_page()
md: reintroduce md-linear
partitions: ldm: remove the initial kernel-doc notation
blk-cgroup: rwstat: fix kernel-doc warnings in header file
blk-cgroup: fix kernel-doc warnings in header file
nbd: fix partial sending
...
|
|
Some PHYs don't support clause 45 access, and return -EOPNOTSUPP from
phy_modify_mmd(), which causes phylink_bringup_phy() to fail. Prevent
this failure by allowing -EOPNOTSUPP to also mean success.
Reported-by: Jiawen Wu <jiawenwu@trustnetic.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1tZp1a-001V62-DT@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce am65_cpsw_create_txqs() and am65_cpsw_destroy_txqs()
and use them.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20250117-am65-cpsw-streamline-v2-3-91a29c97e569@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce am65_cpsw_create_rxqs() and am65_cpsw_destroy_rxqs()
and use them.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20250117-am65-cpsw-streamline-v2-2-91a29c97e569@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We are missing netif_napi_del() and am65_cpsw_nuss_free_tx/rx_chns()
in error path when am65_cpsw_nuss_init_tx/rx_chns() is used anywhere
other than at probe(). i.e. am65_cpsw_nuss_update_tx_rx_chns and
am65_cpsw_nuss_resume()
As reported, in am65_cpsw_nuss_update_tx_rx_chns(),
if am65_cpsw_nuss_init_tx_chns() partially fails then
devm_add_action(dev, am65_cpsw_nuss_free_tx_chns,..) is added
but the cleanup via am65_cpsw_nuss_free_tx_chns() will not run.
Same issue exists for am65_cpsw_nuss_init_tx/rx_chns() failures
in am65_cpsw_nuss_resume() as well.
This would otherwise require more instances of devm_add/remove_action
and is clearly more of a distraction than any benefit.
So, drop devm_add/remove_action for am65_cpsw_nuss_free_tx/rx_chns()
and call am65_cpsw_nuss_free_tx/rx_chns() and netif_napi_del()
where required.
Reported-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Closes: https://lore.kernel.org/all/m4rhkzcr7dlylxr54udyt6lal5s2q4krrvmyay6gzgzhcu4q2c@r34snfumzqxy/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20250117-am65-cpsw-streamline-v2-1-91a29c97e569@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit df542f669307 ("net: stmmac: Switch to zero-copy in
non-XDP RX path"), SKBs are always marked for recycle, it is redundant
to mark SKBs more than once when new frags are appended.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20250117062805.192393-1-0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Two different models of usb card, the drivers are r8152 and asix. If no
network cable is connected, Speed = 10Mb/s. This problem is repeated in
linux 3.10, 4.19, 5.4, 6.12. This problem also exists on the latest
kernel. Both drivers call mii_ethtool_get_link_ksettings,
but the value of cmd->base.speed in this
function can only be SPEED_1000 or SPEED_100 or SPEED_10.
When the network cable is not connected, set cmd->base.speed
=SPEED_UNKNOWN.
Signed-off-by: Xiangqian Zhang <zhangxiangqian@kylinos.cn>
Link: https://patch.msgid.link/20250117094603.4192594-1-zhangxiangqian@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge devfreq and OPP (Operating Performance Points) updates for 6.14:
- Clean up the Exynos devfreq driver and devfreq core (Markus Elfring,
Jeongjun Park).
- Minor cleanups and fixes for OPP (Dan Carpenter, Neil Armstrong, Joe
Hattori).
- Implement dev_pm_opp_get_bw() (Neil Armstrong).
- Expose OPP reference counting helpers for Rust (Viresh Kumar).
* pm-devfreq:
PM / devfreq: exynos: remove unused function parameter
PM / devfreq: event: Call of_node_put() only once in devfreq_event_get_edev_by_phandle()
* pm-opp:
PM / OPP: Add reference counting helpers for Rust implementation
OPP: OF: Fix an OF node leak in _opp_add_static_v2()
OPP: fix dev_pm_opp_find_bw_*() when bandwidth table not initialized
OPP: add index check to assert to avoid buffer overflow in _read_freq()
opp: core: Fix off by one in dev_pm_opp_get_bw()
opp: core: implement dev_pm_opp_get_bw
|
|
300-400B RPC requests are fairly common. With the current default
of 256B HDS threshold bnxt ends up splitting those, lowering PCIe
bandwidth efficiency and increasing the number of memory allocation.
Increase the HDS threshold to fit 4 buffers in a 4k page.
This works out to 640B as the threshold on a typical kernel confing.
This change increases the performance for a microbenchmark which
receives 400B RPCs and sends empty responses by 4.5%.
Admittedly this is just a single benchmark, but 256B works out to
just 6 (so 2 more) packets per head page, because shinfo size
dominates the headers.
Now that we use page pool for the header pages I was also tempted
to default rx_copybreak to 0, but in synthetic testing the copybreak
size doesn't seem to make much difference.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-8-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we can configure HDS threshold separately from the rx_copybreak
HDS threshold may be higher than rx_copybreak.
We need to make sure that we have enough space for the headers.
Fixes: 6b43673a25c3 ("bnxt_en: add support for hds-thresh ethtool command")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-7-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The core has the current HDS config, it can pre-populate the values
for the drivers. While at it, remove the zero-setting in netdevsim.
Zero are the default values since the config is zalloc'ed.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the pending config for hds_thrs. Core will only update the "current"
one after we return success. Without this change 2 reconfigs would be
required for the setting to reach the device.
Fixes: 6b43673a25c3 ("bnxt_en: add support for hds-thresh ethtool command")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Separate the HDS config from the ethtool state struct.
The HDS config contains just simple parameters, not state.
Having it as a separate struct will make it easier to clone / copy
and also long term potentially make it per-queue.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge cpufreq updates for 6.14:
- Use str_enable_disable()-like helpers in cpufreq (Krzysztof
Kozlowski).
- Extend the Apple cpufreq driver to support more SoCs (Hector Martin,
Nick Chan).
- Add new cpufreq driver for Airoha SoCs (Christian Marangi).
- Fix using cpufreq-dt as module (Andreas Kemnade).
- Minor fixes for Sparc, SCMI, and Qcom cpufreq drivers (Ethan Carter
Edwards, Sibi Sankar, Manivannan Sadhasivam).
- Fix the maximum supported frequency computation in the ACPI cpufreq
driver to avoid relying on unfounded assumptions (Gautham Shenoy).
- Fix an amd-pstate driver regression with preferred core rankings not
being used (Mario Limonciello).
- Fix a precision issue with frequency calculation in the amd-pstate
driver (Naresh Solanki).
- Add ftrace event to the amd-pstate driver for active mode (Mario
Limonciello).
- Set default EPP policy on Ryzen processors in amd-pstate (Mario
Limonciello).
- Clean up the amd-pstate cpufreq driver and optimize it to increase
code reuse (Mario Limonciello, Dhananjay Ugwekar).
- Use CPPC to get scaling factors between HWP performance levels and
frequency in the intel_pstate driver and make it stop using a built
-in scaling factor for the Arrow Lake processor (Rafael Wysocki).
- Make intel_pstate initialize epp_policy to CPUFREQ_POLICY_UNKNOWN for
consistency with CPU offline (Christian Loehle).
- Fix superfluous updates caused by need_freq_update in the schedutil
cpufreq governor (Sultan Alsawaf).
* pm-cpufreq: (40 commits)
cpufreq: Use str_enable_disable()-like helpers
cpufreq: airoha: Add EN7581 CPUFreq SMCCC driver
cpufreq: ACPI: Fix max-frequency computation
cpufreq/amd-pstate: Refactor max frequency calculation
cpufreq/amd-pstate: Fix prefcore rankings
cpufreq: sparc: change kzalloc to kcalloc
cpufreq: qcom: Implement clk_ops::determine_rate() for qcom_cpufreq* clocks
cpufreq: qcom: Fix qcom_cpufreq_hw_recalc_rate() to query LUT if LMh IRQ is not available
cpufreq: apple-soc: Add Apple A7-A8X SoC cpufreq support
cpufreq: apple-soc: Set fallback transition latency to APPLE_DVFS_TRANSITION_TIMEOUT
cpufreq: apple-soc: Increase cluster switch timeout to 400us
cpufreq: apple-soc: Use 32-bit read for status register
cpufreq: apple-soc: Allow per-SoC configuration of APPLE_DVFS_CMD_PS1
cpufreq: apple-soc: Drop setting the PS2 field on M2+
dt-bindings: cpufreq: apple,cluster-cpufreq: Add A7-A11, T2 compatibles
dt-bindings: cpufreq: Document support for Airoha EN7581 CPUFreq
cpufreq: fix using cpufreq-dt as module
cpufreq: scmi: Register for limit change notifications
cpufreq: schedutil: Fix superfluous updates caused by need_freq_update
cpufreq: intel_pstate: Use CPUFREQ_POLICY_UNKNOWN
...
|
|
If platform_get_resource_byname("config") fails, return error immediately
and unindent the normal path. No functional change intended.
Link: https://lore.kernel.org/r/20250117235119.712043-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
