| Age | Commit message (Collapse) | Author |
|---|
|
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Cc: stable <stable@vger.kernel.org>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b09d ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Cc: stable@vger.kernel.org
Reviewed-by: Roger Quadros <rogerq@ti.com>
Cc: <stable@vger.kernel.org> #v4.3+
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This flag is a no-op now (see commit 47b0eeb3dc8a "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
mediatek-drm fixes
- remove an invalid, unreachable error message and NULL pointer dereference
- remove a spurious drm_connector_unregister call from the DSI driver
* tag 'mediatek-drm-fixes-2016-06-01' of git://git.pengutronix.de/git/pza/linux:
drm/mediatek: mtk_dsi: Remove spurious drm_connector_unregister
drm/mediatek: mtk_dpi: remove invalid error message
|
|
The address check in acpi_hw_get_access_bit_width() should be byte width
based, not bit width based. This patch fixes this mistake.
For those who want to review acpi_hw_access_bit_width(), here is the
concerns and the design details of the function:
It is supposed that the GAS Address field should be aligned to the byte
width indicated by the GAS AccessSize field. Similarly, for the old non
GAS register, it is supposed that its Address should be aligned to its
Length.
For the "AccessSize = 0 (meaning ANY)" case, we try to return the maximum
instruction width (64 for MMIO or 32 for PIO) or the user expected access
bit width (64 for acpi_read()/acpi_write() or 32 for acpi_hw_read()/
acpi_hw_write()) and it is supposed that the GAS Address field should
always be aligned to the maximum expected access bit width (otherwise it
can't be accessed using ANY access bit width).
The problem is in acpi_tb_init_generic_address(), where the non GAS
register's Length is converted into the GAS BitWidth field, its Address is
converted into the GAS Address field, and the GAS AccessSize field is left
0 but most of the registers actually cannot be accessed using "ANY"
accesses.
As a conclusion, when AccessSize = 0 (ANY), the Address should either be
aligned to the BitWidth (wrong conversion) or aligned to 32 for PIO or 64
for MMIO (real GAS). Since currently, max_bit_width is 32, then:
1. BitWidth for the wrong conversion is 8,16,32; and
2. The Address of the real GAS should always be aligned to 8,16,32.
The address alignment check to exclude false matched real GAS is not
necessary. Thus this patch fixes the issue by removing the address
alignment check.
On the other hand, we in fact could use a simpler check of
"reg->bit_width < max_bit_width" to exclude the "BitWidth=64 PIO" case that
may be issued from acpi_read()/acpi_write() in the future.
Fixes: b314a172ee96 (ACPICA: Hardware: Add optimized access bit width support)
Reported-and-tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The return value of clamp_val() has to be stored actually.
Fixes: b7898fda5bc7 (cpufreq: Support for fast frequency switching)
Reported-by: Steve Muckle <steve.muckle@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes for v4.7. Not much, and just driver
fixes:
- add device tree matches to MAINTAINERS
- inversion bug in the Nomadik driver
- dual edge handling bug in the mediatek driver"
* tag 'pinctrl-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: fix dual-edge code defect
MAINTAINERS: Add file patterns for pinctrl device tree bindings
pinctrl: nomadik: fix inversion of gpio direction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf updates from Sumit Semwal:
- use of vma_pages instead of explicit computation
- DocBook and headerdoc updates for dma-buf
* tag 'dma-buf-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
dma-buf: use vma_pages()
fence: add missing descriptions for fence
doc: update/fixup dma-buf related DocBook
reservation: add headerdoc comments
dma-buf: headerdoc fixes
|
|
The freq_table array is not populated before calling
thermal_of_cooling_register. The code which populates the freq table was
introduced in commit f6859014.
This should be done before registering new thermal cooling device.
The log shows effects of this wrong decision.
[ 2.172614] cpu cpu1: Failed to get voltage for frequency 1984518656000: -34
[ 2.220863] cpu cpu0: Failed to get voltage for frequency 1984524416000: -34
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: f6859014c7e7 ("thermal: cpu_cooling: Store frequencies in descending order")
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Javi Merino <javi.merino@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Connectors are unregistered by mtk_drm_drv via drm_connector_unregister_all().
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Do not try to dereference dpi if it is NULL.
Since dpi can never be NULL when mtk_dpi_set_display_mode() is called,
remove the message.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The firmware found in the touch screen of an SP3 is buggy and may miss
to send lift off reports for contacts. Try to work around that issue by
using MT_QUIRK_NOT_SEEN_MEANS_UP.
based on a patch from: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If kmalloc() returned NULL we would end up dereferencing "state" a
couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Reset crtc->state to NULL after freeing the state object and call
__drm_atomic_helper_crtc_destroy_state() helper instead of manually
calling drm_property_unreference_blob().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Flushing a work that reschedules itself is not a sensible operation. It needs
to be killed. Failure to do so leads to a kernel panic in the timer code.
CC: stable@vger.kernel.org
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
As of core revision 2.60a the recommended programming model is to set
the ClearPendIN bit when issuing a Clear Stall EP command for IN
endpoints. This is to prevent an issue where some (non-compliant) hosts
may not send ACK TPs for pending IN transfers due to a mishandled error
condition. Synopsys STAR 9000614252.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Pull networking fixes from David Miller:
1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.
2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
properly. From Ezequiel Garcia.
3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.
4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.
5) Fix deadlock on team->lock when propagating features, from Ivan
Vecera.
6) Work around buffer offset hw bug in alx chips, from Feng Tang.
7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
Long.
8) Various statistics bug fixes in mlx4 from Eric Dumazet.
9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.
10) All of l2tp was namespace aware, but the ipv6 support code was not
doing so. From Shmulik Ladkani.
11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.
12) Propagate MAC changes properly through VLAN devices, from Mike
Manning.
13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
sfc: Track RPS flow IDs per channel instead of per function
usbnet: smsc95xx: fix link detection for disabled autonegotiation
virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
bnx2x: avoid leaking memory on bnx2x_init_one() failures
fou: fix IPv6 Kconfig options
openvswitch: update checksum in {push,pop}_mpls
sctp: sctp_diag should dump sctp socket type
net: fec: update dirty_tx even if no skb
vlan: Propagate MAC address to VLANs
atm: iphase: off by one in rx_pkt()
atm: firestream: add more reserved strings
vxlan: Accept user specified MTU value when create new vxlan link
net: pktgen: Call destroy_hrtimer_on_stack()
timer: Export destroy_hrtimer_on_stack()
net: l2tp: Make l2tp_ip6 namespace aware
Documentation: ip-sysctl.txt: clarify secure_redirects
sfc: use flow dissector helpers for aRFS
ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
net: nps_enet: Disable interrupts before napi reschedule
net/lapb: tuse %*ph to dump buffers
...
|
|
- Fixed black screen for some resolutions of G200e rev4
- Fixed testm & testn which had predetermined value.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Since the introduction of (struct_mutex) lockless GEM bo freeing, there
are a pair of driver vfuncs for freeing the GEM bo, of which the driver
may choose to only implement driver->gem_object_free_unlocked (and so
avoid taking the struct_mutex along the free path). However, the CMA GEM
helpers were still calling driver->gem_free_object directly, now NULL,
and promptly dying on the fancy new lockless drivers. Oops.
Robert Foss bisected this to b82caafcf2303 (drm/vc4: Use lockless gem BO
free callback) on his vc4 device, but that just serves as an enabler for
9f0ba539d13ae (drm/gem: support BO freeing without dev->struct_mutex).
Reported-by: Robert Foss <robert.foss@collabora.com>
Fixes: 9f0ba539d13ae (drm/gem: support BO freeing without dev->struct_mutex)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Robert Foss <robert.foss@collabora.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
After commit 027b3f8ba9277410c3191d72d1ed2c6146d8a668 ("drm/modes: stop
handling framebuffer special") extra fb refs are left around when doing
atomic modesetting.
The problem is that the new drm_property_change_valid_get() does not
return anything in the '**ref' parameter, which causes
drm_property_change_valid_put() to do nothing.
For some reason this doesn't cause problems with legacy API.
Also, previously the code only set the 'ref' variable for fbs, with this
patch the 'ref' is set for all objects.
Fixes: 027b3f8ba927 ("drm/modes: stop handling framebuffer special")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drm_atomic_set_mode_prop_for_crtc() does not clear the state->mode, so
old data may be left there when a new mode is set, possibly causing odd
issues.
This patch improves the situation by always clearing the state->mode
first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Commit 652353e6e561c2aeeac62df183f721f6f9b5b45f ("drm/sti: set CRTC
modesetting parameters") added a hack to avoid warnings related to
setting mode with atomic API. With the previous patch, the hack should
no longer be necessary.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When setting mode via MODE_ID property,
drm_atomic_set_mode_prop_for_crtc() does not call
drm_mode_set_crtcinfo() which possibly causes:
"[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 32: Can't
calculate constants, dotclock = 0!"
Whether the error is seen depends on the previous data in state->mode,
as state->mode is not cleared when setting new mode.
This patch adds drm_mode_set_crtcinfo() call to
drm_mode_convert_umode(), which is called in both legacy and atomic
paths. This should be fine as there's no reason to call
drm_mode_convert_umode() without also setting the crtc related fields.
drm_mode_set_crtcinfo() is removed from the legacy drm_mode_setcrtc() as
that is no longer needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Otherwise we get confused when two flows on different channels get the
same flow ID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size of the VPD area is not necessarily 4-byte aligned, so a
pci_vpd_read() might return less than 4 bytes. Zero our buffer and
accept anything other than an error. Intel X710 NICs exercise this.
Fixes: 4e1a635552d3 ("vfio/pci: Use kernel VPD access functions")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Linux fails to boot as a guest with a QEMU CD-ROM:
[ 4.439488] ata2.00: ATAPI: QEMU CD-ROM, 0.8.2, max UDMA/100
[ 4.443649] ata2.00: configured for MWDMA2
[ 4.450267] scsi 1:0:0:0: CD-ROM QEMU QEMU CD-ROM 0.8. PQ: 0 ANSI: 5
[ 4.464317] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 4.464319] ata2.00: BMDMA stat 0x5
[ 4.464339] ata2.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 0 dma 16640 in
[ 4.464339] Inquiry 12 01 00 00 ff 00res 48/20:02:00:24:00/00:00:00:00:00/a0 Emask 0x2 (HSM violation)
[ 4.464341] ata2.00: status: { DRDY DRQ }
[ 4.465864] ata2: soft resetting link
[ 4.625971] ata2.00: configured for MWDMA2
[ 4.628290] ata2: EH complete
[ 4.646670] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 4.646671] ata2.00: BMDMA stat 0x5
[ 4.646683] ata2.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 0 dma 16640 in
[ 4.646683] Inquiry 12 01 00 00 ff 00res 48/20:02:00:24:00/00:00:00:00:00/a0 Emask 0x2 (HSM violation)
[ 4.646685] ata2.00: status: { DRDY DRQ }
[ 4.648193] ata2: soft resetting link
...
Fix this by suppressing VPD inquiry for this device.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As per the documentation in drm_crtc.h, atomic_commit should return
-EBUSY if an asynchronous update is requested and there is an earlier
update pending.
v2: Rebase on the s/async/nonblock/ change.
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
The async page flip path was missing drm_crtc_vblank_get/put
completely. The sync flip path was missing a vblank put, so async
flips only reported proper pageflip completion events by chance,
and vblank irq's never turned off after a first vsync'ed page flip
until system reboot.
Tested against Raspian kernel 4.4.8 tree on RPi 2B.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Fixes: b501bacc6060 ("drm/vc4: Add support for async pageflips.")
|
|
get_vblank_counter hooked up to drm_vblank_count() which alway was
non-sensical but didn't hurt in the past. Since Linux 4.4 it
triggers a WARN_ON_ONCE in drm_update_vblank_count on first vblank
irq disable, so fix it by hooking to drm_vblank_no_hw_counter().
Tested against Raspian kernel 4.4.8 tree on RPi 2B.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Fixes: c8b75bca92cb ("drm/vc4: Add KMS support for Raspberry Pi.")
|
|
To detect link status up/down for connections where autonegotiation is
explicitly disabled, we don't get an irq but need to poll the status
register for link up/down detection.
This patch adds a workqueue to poll for link status.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function virtnet_open() and virtnet_probe(), func try_fill_recv() may
be executed at the same time. VQ in virtqueue_add() has not been protected
well and BUG_ON will be triggered when virito_net.ko being removed.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we
fail later in bnx2x_init_one() we need to free this memory
with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory
leaks reported by kmemleak when a failure (unrelated) happens in
bnx2x_vfpf_acquire().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If dirty_tx isn't updated, then dma_unmap_single
can be called twice.
This fixes a
[ 58.420980] ------------[ cut here ]------------
[ 58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[ 58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]
encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The iadev->rx_open[] array holds "iadev->num_vc" pointers (this code
assumes that pointers are 32 bits). So the > here should be >= or else
we could end up reading a garbage pointer from one element beyond the
end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This bug was there when the driver was first added in back in year 2000.
It causes a Smatch warning:
drivers/atm/firestream.c:849 process_incoming()
error: buffer overflow 'res_strings' 60 <= 63
There are supposed to be 64 entries in this array and the missing
strings are clearly in the 30 40 range. I added them as reserved 37 to
reserved 40. It's possible that strings are really supposed to be added
in the middle instead of at the end, but this approach is safe, in that
it fixes the bug and doesn't break anything that wasn't already broken.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When create a new vxlan link, example:
ip link add vtap mtu 1440 type vxlan vni 1 dev eth0
The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.
This problem was introduced by commit 0dfbdf4102b9 (vxlan: Factor out device
configuration).
Fixes: 0dfbdf4102b9 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace explicit computation of vma page count by a call to
vma_pages().
Also, include <linux/mm.h>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A bunch of GPIO fixes for the v4.7 series:
- Drop the lock before reading out the GPIO direction setting in
drivers supporting the .get_direction() callback: some of them may
be slowpath.
- Flush GPIO direction setting before locking a GPIO as an IRQ: some
electronics or other poking around in the registers behind our back
may have happened, so flush the direction status before trying to
lock the line for use by IRQs.
- Bail out silently when asked to perform operations on NULL GPIO
descriptors. That is what all the get_*_optional() is about: we
get optional GPIO handles, if they are not there, we get NULL.
- Handle compatible ioctl() correctly: we need to convert the ioctl()
pointer using compat_ptr() here like everyone else.
- Disable the broken .to_irq() on the LPC32xx platform. The whole
irqchip infrastructure was replaced in the last merge window, and a
new implementation will be needed"
* tag 'gpio-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: drop lock before reading GPIO direction
gpio: bail out silently on NULL descriptors
gpio: handle compatible ioctl() pointers
gpio: flush direction status in gpiochip_lock_as_irq()
gpio: lpc32xx: disable broken to_irq support
|
|
According to the datasheet:
SLEW Register(Address = 07h)
b7 b6 b5 b4 b3 b2 b1 b0
48mV/us 42mV/us 36mV/us 30mV/us 24mV/us 18mV/us 12mV/us 6mV/us
Current code does not set correct slew rate in some cases:
e.g. Assume ramp_delay is 10000, current code sets slew register to 6mV/us.
Fix the logic to set slew register.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A wmediumd that does not send this attribute causes a NULL pointer
dereference, as the attribute is accessed even if it does not exist.
The attribute was required but never checked ever since userspace frame
forwarding has been introduced. The issue gets more problematic once we
allow wmediumd registration from user namespaces.
Cc: stable@vger.kernel.org
Fixes: 7882513bacb1 ("mac80211_hwsim driver support userspace frame tx/rx")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Set USB3_FORCE_VBUSVALID when configured for USB_DR_MODE_PERIPHERAL
mode, as it is required to have a working setup.
This worked on the internal driver by relying on the reset
value of the syscfg register as the bits aren't explicity cleared
and set like the upstream driver.
Also add a comment about what setting this bit means.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In OS descriptors handling, if ctrl->bRequestType is
USB_RECIP_DEVICE and w_index != 0x4 or (w_value >> 8)
is true, it will not assign a valid value to req->length,
but use the default value(-EOPNOTSUPP), and queue an
OS desc request with the invalid req->length. It always
happens on the platforms which use os_desc (for example:
rk3366, rk3399), and cause kernel panic as follows
(use dwc3 driver):
Unable to handle kernel paging request at virtual address ffffffc0f7e00000
Internal error: Oops: 96000146 [#1] PREEMPT SMP
PC is at __dma_clean_range+0x18/0x30
LR is at __swiotlb_map_page+0x50/0x64
Call trace:
[<ffffffc0000930f8>] __dma_clean_range+0x18/0x30
[<ffffffc00062214c>] usb_gadget_map_request+0x134/0x1b0
[<ffffffc0005c289c>] __dwc3_ep0_do_control_data+0x110/0x14c
[<ffffffc0005c2d38>] __dwc3_gadget_ep0_queue+0x198/0x1b8
[<ffffffc0005c2e18>] dwc3_gadget_ep0_queue+0xc0/0xe8
[<ffffffc00061cfec>] composite_ep0_queue.constprop.14+0x34/0x98
[<ffffffc00061dfb0>] composite_setup+0xf60/0x100c
[<ffffffc0006204dc>] android_setup+0xd8/0x138
[<ffffffc0005c29a4>] dwc3_ep0_delegate_req+0x34/0x50
[<ffffffc0005c3534>] dwc3_ep0_interrupt+0x5dc/0xb58
[<ffffffc0005c0c3c>] dwc3_thread_interrupt+0x15c/0xa24
With this patch, the gadget driver will not queue
a request and return immediately if req->length is
invalid. And the usb controller driver can handle
the unsupport request correctly.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If c->cdev->use_os_string flag is not set,
don't need to invoke ffs_do_os_descs() in _ffs_func_bind.
So uninitialized ext_compat_id pointer won't be accessed by
__ffs_func_bind_do_os_desc to cause kernel panic.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Commit dc8c46a5ae77 ("usb: gadget: f_tcm: convert to new function
interface with backward compatibility") introduced a possible out
of bounds memory access:
If tpg is not found in function usbg_drop_tpg,
tpg_instances[TPG_INSTANCES] is accessed.
Fixes: dc8c46a5ae77 ("usb: gadget: f_tcm: convert to new function interface with backward compatibility")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Function in_rq_cur copies random bytes from the stack.
Zero the memory instead.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
A patch that went into Linux-4.4 to fix big-endian mode on a Lantiq
MIPS system unfortunately broke big-endian operation on PowerPC
APM82181 as reported by Christian Lamparter, and likely other
systems.
It actually introduced multiple issues:
- it broke big-endian ARM kernels: any machine that was working
correctly with a little-endian kernel is no longer using byteswaps
on big-endian kernels, which clearly breaks them.
- On PowerPC the same thing must be true: if it was working before,
using big-endian kernels is now broken. Unlike ARM, 32-bit PowerPC
usually uses big-endian kernels, so they are likely all broken.
- The barrier for dwc2_writel is on the wrong side of the __raw_writel(),
so the MMIO no longer synchronizes with DMA operations.
- On architectures that require specific CPU instructions for MMIO
access, using the __raw_ variant may turn this into a pointer
dereference that does not have the same effect as the readl/writel.
This patch is a simple revert for all architectures other than MIPS,
in the hope that we can more easily backport it to fix the regression
on PowerPC and ARM systems without breaking the Lantiq system again.
We should follow this up with a more elaborate change to add runtime
detection of endianness, to make sure it also works on all other
combinations of architectures and implementations of the usb-dwc2
device. That patch however will be fairly large and not appropriate
for backports to stable kernels.
Felipe suggested a different approach, using an endianness switching
register to always put the device into LE mode, but unfortunately
the dwc2 hardware does not provide a generic way to do that. Also,
I see no practical way of addressing the problem more generally by
patching architecture specific code on MIPS.
Fixes: 95c8bc360944 ("usb: dwc2: Use platform endianness when accessing registers")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.
Cc: stable@vger.kernel.org
Signed-off-by: Hongkun Cao <hongkun.cao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Current __ffs_data_do_os_desc() of f_fs.c will check reserved1 field
of OS_DESC_EXT_COMPAT and return -EINVAL if it's 1.
But MS OS 1.0 Descriptors
http://msdn.microsoft.com/en-us/library/windows/hardware/gg463179.aspx
defines that field to be 1.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Device qualifier descriptor is now generated by composite.c
code. So let's fix this old comment by removing parts which
are no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
