| Age | Commit message (Collapse) | Author |
|---|
|
drm_fb_cma code has a nice helper function to display in the debugfs
information about the underlying framebuffers used by HDLCD:
$ cat /sys/kernel/debug/dri/0/fb
fb: 1920x1200@XR24
0: offset=0 pitch=7680, obj: 0 ( 2) 001011ba 0x00000000fc300000 ffffff800a27c000 9338880
fb: 1920x1200@XR24
0: offset=0 pitch=7680, obj: 0 ( 2) 001008ca 0x00000000fba00000 ffffff8009987000 9338880
fb: 1920x1200@XR24
0: offset=0 pitch=7680, obj: 0 ( 1) 00100000 0x00000000fb100000 ffffff8008fdc000 9216000
Add the entry in HDLCD's debugfs node.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
Harden the plane_check() code to drop attempts at scaling because
that is not supported. Make hdlcd_plane_atomic_update() set the pitch
and line length registers that correctly reflect the plane's values.
And make hdlcd_crtc_mode_set_nofb() a helper function for
hdlcd_crtc_enable() rather than an exposed hook.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
event_list just reimplemented what drm_crtc_arm_vblank_event does. And
we also need to send out drm events when shutting down a pipe.
With this it's possible to use the new nonblocking commit support in
the helpers.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
Because the HDLCD driver acts as a component master it can end
up enabling the runtime PM functionality before the encoders
are initialised. This can cause crashes if the component slave
never probes (missing module) or if the PM operations kick in
before the probe finishes.
Move the enabling of the runtime PM after the component master
has finished collecting the slave components and use the DRM
atomic helpers to suspend and resume the device.
Tested-by: Robin Murphy <Robin.Murphy@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
Now the the HS-DDR mode clock timings have been corrected, we can
re-enable these modes on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The MMC clock timings were incorrectly calculated, when the conversion
from delay value to delay phase was done.
The 50M DDR and 50M DDR 8bit timings are off, and make eMMC DDR
unusable. Unfortunately it seems different controllers on the same SoC
have different timings. The new settings are taken from mmc2, which is
commonly used with eMMC.
The settings for the slower timing modes seem to work despite being
wrong, so leave them be.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When IS_ERR_VALUE was removed from the mmc core code, it was replaced
with a simple not-zero check. This does not work, as the value checked
is the return value for mmc_select_bus_width, which returns the set
bit width on success. This made eMMC modes higher than HS-DDR unusable.
Fix this by checking for a positive return value instead.
Fixes: 287980e49ffc ("remove lots of IS_ERR_VALUE abuses")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Roland Dreier reports that one of his systems cannot boot because of
the changes made by commit ac212b6980d8 (ACPI / processor: Use common
hotplug infrastructure).
The problematic part of it is the request_region() call in
acpi_processor_get_info() that used to run at module init time before
the above commit and now it runs much earlier. Unfortunately, the
region(s) reserved by it fall into a range the PCI subsystem attempts
to reserve for AHCI IO BARs. As a result, the PCI reservation fails
and AHCI doesn't work, while previously the PCI reservation would
be made before acpi_processor_get_info() and it would succeed.
That request_region() call, however, was overlooked by commit
ac212b6980d8, as it is not necessary for the enumeration of the
processors. It only is needed when the ACPI processor driver
actually attempts to handle them which doesn't happen before
loading the ACPI processor driver module. Therefore that call
should have been moved from acpi_processor_get_info() into that
module.
Address the problem by moving the request_region() call in question
out of acpi_processor_get_info() and use the observation that the
region reserved by it is only needed if the FADT-based CPU
throttling method is going to be used, which means that it should
be sufficient to invoke it from acpi_processor_get_throttling_fadt().
Fixes: ac212b6980d8 (ACPI / processor: Use common hotplug infrastructure)
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
mediatek-drm fixes
- remove an invalid, unreachable error message and NULL pointer dereference
- remove a spurious drm_connector_unregister call from the DSI driver
* tag 'mediatek-drm-fixes-2016-06-01' of git://git.pengutronix.de/git/pza/linux:
drm/mediatek: mtk_dsi: Remove spurious drm_connector_unregister
drm/mediatek: mtk_dpi: remove invalid error message
|
|
The address check in acpi_hw_get_access_bit_width() should be byte width
based, not bit width based. This patch fixes this mistake.
For those who want to review acpi_hw_access_bit_width(), here is the
concerns and the design details of the function:
It is supposed that the GAS Address field should be aligned to the byte
width indicated by the GAS AccessSize field. Similarly, for the old non
GAS register, it is supposed that its Address should be aligned to its
Length.
For the "AccessSize = 0 (meaning ANY)" case, we try to return the maximum
instruction width (64 for MMIO or 32 for PIO) or the user expected access
bit width (64 for acpi_read()/acpi_write() or 32 for acpi_hw_read()/
acpi_hw_write()) and it is supposed that the GAS Address field should
always be aligned to the maximum expected access bit width (otherwise it
can't be accessed using ANY access bit width).
The problem is in acpi_tb_init_generic_address(), where the non GAS
register's Length is converted into the GAS BitWidth field, its Address is
converted into the GAS Address field, and the GAS AccessSize field is left
0 but most of the registers actually cannot be accessed using "ANY"
accesses.
As a conclusion, when AccessSize = 0 (ANY), the Address should either be
aligned to the BitWidth (wrong conversion) or aligned to 32 for PIO or 64
for MMIO (real GAS). Since currently, max_bit_width is 32, then:
1. BitWidth for the wrong conversion is 8,16,32; and
2. The Address of the real GAS should always be aligned to 8,16,32.
The address alignment check to exclude false matched real GAS is not
necessary. Thus this patch fixes the issue by removing the address
alignment check.
On the other hand, we in fact could use a simpler check of
"reg->bit_width < max_bit_width" to exclude the "BitWidth=64 PIO" case that
may be issued from acpi_read()/acpi_write() in the future.
Fixes: b314a172ee96 (ACPICA: Hardware: Add optimized access bit width support)
Reported-and-tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The return value of clamp_val() has to be stored actually.
Fixes: b7898fda5bc7 (cpufreq: Support for fast frequency switching)
Reported-by: Steve Muckle <steve.muckle@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes for v4.7. Not much, and just driver
fixes:
- add device tree matches to MAINTAINERS
- inversion bug in the Nomadik driver
- dual edge handling bug in the mediatek driver"
* tag 'pinctrl-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: fix dual-edge code defect
MAINTAINERS: Add file patterns for pinctrl device tree bindings
pinctrl: nomadik: fix inversion of gpio direction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf updates from Sumit Semwal:
- use of vma_pages instead of explicit computation
- DocBook and headerdoc updates for dma-buf
* tag 'dma-buf-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
dma-buf: use vma_pages()
fence: add missing descriptions for fence
doc: update/fixup dma-buf related DocBook
reservation: add headerdoc comments
dma-buf: headerdoc fixes
|
|
Connectors are unregistered by mtk_drm_drv via drm_connector_unregister_all().
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Do not try to dereference dpi if it is NULL.
Since dpi can never be NULL when mtk_dpi_set_display_mode() is called,
remove the message.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
If kmalloc() returned NULL we would end up dereferencing "state" a
couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Reset crtc->state to NULL after freeing the state object and call
__drm_atomic_helper_crtc_destroy_state() helper instead of manually
calling drm_property_unreference_blob().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Pull networking fixes from David Miller:
1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.
2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
properly. From Ezequiel Garcia.
3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.
4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.
5) Fix deadlock on team->lock when propagating features, from Ivan
Vecera.
6) Work around buffer offset hw bug in alx chips, from Feng Tang.
7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
Long.
8) Various statistics bug fixes in mlx4 from Eric Dumazet.
9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.
10) All of l2tp was namespace aware, but the ipv6 support code was not
doing so. From Shmulik Ladkani.
11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.
12) Propagate MAC changes properly through VLAN devices, from Mike
Manning.
13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
sfc: Track RPS flow IDs per channel instead of per function
usbnet: smsc95xx: fix link detection for disabled autonegotiation
virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
bnx2x: avoid leaking memory on bnx2x_init_one() failures
fou: fix IPv6 Kconfig options
openvswitch: update checksum in {push,pop}_mpls
sctp: sctp_diag should dump sctp socket type
net: fec: update dirty_tx even if no skb
vlan: Propagate MAC address to VLANs
atm: iphase: off by one in rx_pkt()
atm: firestream: add more reserved strings
vxlan: Accept user specified MTU value when create new vxlan link
net: pktgen: Call destroy_hrtimer_on_stack()
timer: Export destroy_hrtimer_on_stack()
net: l2tp: Make l2tp_ip6 namespace aware
Documentation: ip-sysctl.txt: clarify secure_redirects
sfc: use flow dissector helpers for aRFS
ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
net: nps_enet: Disable interrupts before napi reschedule
net/lapb: tuse %*ph to dump buffers
...
|
|
- Fixed black screen for some resolutions of G200e rev4
- Fixed testm & testn which had predetermined value.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Since the introduction of (struct_mutex) lockless GEM bo freeing, there
are a pair of driver vfuncs for freeing the GEM bo, of which the driver
may choose to only implement driver->gem_object_free_unlocked (and so
avoid taking the struct_mutex along the free path). However, the CMA GEM
helpers were still calling driver->gem_free_object directly, now NULL,
and promptly dying on the fancy new lockless drivers. Oops.
Robert Foss bisected this to b82caafcf2303 (drm/vc4: Use lockless gem BO
free callback) on his vc4 device, but that just serves as an enabler for
9f0ba539d13ae (drm/gem: support BO freeing without dev->struct_mutex).
Reported-by: Robert Foss <robert.foss@collabora.com>
Fixes: 9f0ba539d13ae (drm/gem: support BO freeing without dev->struct_mutex)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Robert Foss <robert.foss@collabora.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
After commit 027b3f8ba9277410c3191d72d1ed2c6146d8a668 ("drm/modes: stop
handling framebuffer special") extra fb refs are left around when doing
atomic modesetting.
The problem is that the new drm_property_change_valid_get() does not
return anything in the '**ref' parameter, which causes
drm_property_change_valid_put() to do nothing.
For some reason this doesn't cause problems with legacy API.
Also, previously the code only set the 'ref' variable for fbs, with this
patch the 'ref' is set for all objects.
Fixes: 027b3f8ba927 ("drm/modes: stop handling framebuffer special")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drm_atomic_set_mode_prop_for_crtc() does not clear the state->mode, so
old data may be left there when a new mode is set, possibly causing odd
issues.
This patch improves the situation by always clearing the state->mode
first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Commit 652353e6e561c2aeeac62df183f721f6f9b5b45f ("drm/sti: set CRTC
modesetting parameters") added a hack to avoid warnings related to
setting mode with atomic API. With the previous patch, the hack should
no longer be necessary.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When setting mode via MODE_ID property,
drm_atomic_set_mode_prop_for_crtc() does not call
drm_mode_set_crtcinfo() which possibly causes:
"[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 32: Can't
calculate constants, dotclock = 0!"
Whether the error is seen depends on the previous data in state->mode,
as state->mode is not cleared when setting new mode.
This patch adds drm_mode_set_crtcinfo() call to
drm_mode_convert_umode(), which is called in both legacy and atomic
paths. This should be fine as there's no reason to call
drm_mode_convert_umode() without also setting the crtc related fields.
drm_mode_set_crtcinfo() is removed from the legacy drm_mode_setcrtc() as
that is no longer needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Otherwise we get confused when two flows on different channels get the
same flow ID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size of the VPD area is not necessarily 4-byte aligned, so a
pci_vpd_read() might return less than 4 bytes. Zero our buffer and
accept anything other than an error. Intel X710 NICs exercise this.
Fixes: 4e1a635552d3 ("vfio/pci: Use kernel VPD access functions")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
To detect link status up/down for connections where autonegotiation is
explicitly disabled, we don't get an irq but need to poll the status
register for link up/down detection.
This patch adds a workqueue to poll for link status.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function virtnet_open() and virtnet_probe(), func try_fill_recv() may
be executed at the same time. VQ in virtqueue_add() has not been protected
well and BUG_ON will be triggered when virito_net.ko being removed.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we
fail later in bnx2x_init_one() we need to free this memory
with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory
leaks reported by kmemleak when a failure (unrelated) happens in
bnx2x_vfpf_acquire().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If dirty_tx isn't updated, then dma_unmap_single
can be called twice.
This fixes a
[ 58.420980] ------------[ cut here ]------------
[ 58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[ 58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]
encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The iadev->rx_open[] array holds "iadev->num_vc" pointers (this code
assumes that pointers are 32 bits). So the > here should be >= or else
we could end up reading a garbage pointer from one element beyond the
end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This bug was there when the driver was first added in back in year 2000.
It causes a Smatch warning:
drivers/atm/firestream.c:849 process_incoming()
error: buffer overflow 'res_strings' 60 <= 63
There are supposed to be 64 entries in this array and the missing
strings are clearly in the 30 40 range. I added them as reserved 37 to
reserved 40. It's possible that strings are really supposed to be added
in the middle instead of at the end, but this approach is safe, in that
it fixes the bug and doesn't break anything that wasn't already broken.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When create a new vxlan link, example:
ip link add vtap mtu 1440 type vxlan vni 1 dev eth0
The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.
This problem was introduced by commit 0dfbdf4102b9 (vxlan: Factor out device
configuration).
Fixes: 0dfbdf4102b9 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace explicit computation of vma page count by a call to
vma_pages().
Also, include <linux/mm.h>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A bunch of GPIO fixes for the v4.7 series:
- Drop the lock before reading out the GPIO direction setting in
drivers supporting the .get_direction() callback: some of them may
be slowpath.
- Flush GPIO direction setting before locking a GPIO as an IRQ: some
electronics or other poking around in the registers behind our back
may have happened, so flush the direction status before trying to
lock the line for use by IRQs.
- Bail out silently when asked to perform operations on NULL GPIO
descriptors. That is what all the get_*_optional() is about: we
get optional GPIO handles, if they are not there, we get NULL.
- Handle compatible ioctl() correctly: we need to convert the ioctl()
pointer using compat_ptr() here like everyone else.
- Disable the broken .to_irq() on the LPC32xx platform. The whole
irqchip infrastructure was replaced in the last merge window, and a
new implementation will be needed"
* tag 'gpio-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: drop lock before reading GPIO direction
gpio: bail out silently on NULL descriptors
gpio: handle compatible ioctl() pointers
gpio: flush direction status in gpiochip_lock_as_irq()
gpio: lpc32xx: disable broken to_irq support
|
|
When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.
Cc: stable@vger.kernel.org
Signed-off-by: Hongkun Cao <hongkun.cao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A lot of the display drivers for OMAP use the gpio descriptor functions
that are only available in linux/gpio.h if GPIOLIB is enabled and
otherwise produce a build error:
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c: In function 'opa362_enable':
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c:101:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-dpi.c: In function 'panel_dpi_probe_pdata':
drivers/gpu/drm/omapdrm/displays/panel-dpi.c:189:23: error: implicit declaration of function 'gpio_to_desc' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c: In function 'sharp_ls_enable':
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c:120:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
This replaces the existing linux/gpio.h with linux/gpio/consumer.h
where needed. In case of panel-lgphilips-lb035q02.c however, we
also have to include linux/gpio.h to get the definition of gpio_is_valid
and gpio_set_value_cansleep that are used for the non-DT case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[tomi.valkeinen@ti.com: resolved conflicts]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The omapdrm driver relies on this header to be included
implicitly, but this does not always work, and I get
this error in randconfig builds:
gpu/drm/omapdrm/dss/hdmi_phy.c: In function 'hdmi_phy_dump':
gpu/drm/omapdrm/dss/hdmi_phy.c:34:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_wp.c: In function 'hdmi_wp_dump':
gpu/drm/omapdrm/dss/hdmi_wp.c:26:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_pll.c: In function 'hdmi_pll_dump':
gpu/drm/omapdrm/dss/hdmi_pll.c:30:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
This adds the #include statements in all files that have
a seq_printf statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This reverts commit 1c278e5e3718d15475ec08ee2135f37a6b13361c.
If DRM_OMAP does not select OMAP2_DSS it is possible to build a kernel with
DRM_OMAP only and not selecting OMAP2_DSS. Since omapdrm depends on
OMAP2_DSS this will result on broken kernel build.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
regulator_can_change_voltage() is deprecated and it's use is not necessary
as commit:
6a0028b3dd67b regulator: Deprecate regulator_can_change_voltage()
describers it clearly.
Also, regulator_set_voltage() is misused in the driver, as it is
supposed to be used only in cases where the regulator voltage needs to
be changed dynamically at runtime. In DSS's case, we always want a fixed
voltage, set in the .dts files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The DDC scl high and low times were set to the minimum values
from the i2c specification, but the i2c specification takes into
account the rise time and fall time to calculate the frequency.
To pass HDMI certification DDC can not exceed 100kHz therefore in
a system where the rise times and fall times are negligible the high
and low times for scl need to be 10us.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The AVI infoframe R0-R3 in the 2nd data byte represents the
Active Format Aspect Ratio. It is four bits long not two bits.
This fixes that mask used to extract the bits before writing the
bits to the hardware registers.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
hdmi_core_powerdown_disable() is supposed to disable HDMI core's
power-down mode. However, the function sets the power-down bit to 0,
which means "enable power-down".
This hasn't caused any issues as the PD seems to affect only interrupts
from HDMI core, and none of those interrupts are used at the moment. CEC
functionality requires core interrupts, and the PD mode needs to be
fixed.
This patch fixes hdmi_core_powerdown_disable() to actually disable the
PD mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
With certain kernel config options many omapdrm files fail to compile
due to missing include of linux/gpio/consumer.h and linux/of.h.
This patch adds those includes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
In some configurations, we can build the OMAP dss driver without
implictly including the pinctrl consumer definitions, causing
a build error:
gpu/drm/omapdrm/dss/dss.c: In function 'dss_runtime_suspend':
gpu/drm/omapdrm/dss/dss.c:1268:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
This adds an explicit #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- missing selection in public_key that may result in a build failure
- Potential crash in error path in omap-sham
- ccp AES XTS bug that affects requests larger than 4096"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccp - Fix AES XTS error for request sizes above 4096
crypto: public_key: select CRYPTO_AKCIPHER
crypto: omap-sham - potential Oops on error in probe
|
|
When adding the gpiochip, the GPIO HW drivers' callback get_direction()
could get called in atomic context. Some of the GPIO HW drivers may
sleep when accessing the register.
Move the lock before initializing the descriptors.
Reported-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In fdeb8e1547cb9dd39d5d7223b33f3565cf86c28e
("gpio: reflect base and ngpio into gpio_device")
assumed that GPIO descriptors are either valid or error
pointers, but gpiod_get_[index_]optional() actually return
NULL descriptors and then all subsequent calls should just
bail out.
Cc: stable@vger.kernel.org
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Fixes: fdeb8e1547cb ("gpio: reflect base and ngpio into gpio_device")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If we're using the compatible ioctl() we need to handle the
argument pointer in a special way or there will be trouble.
Fixes: 3c702e9987e2 ("gpio: add a userspace chardev ABI for GPIOs")
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
