| Age | Commit message (Collapse) | Author |
|---|
|
PX-BCUD has the following components:
USB interface: Empia EM28178
Demodulator: Toshiba TC90532 (works by code for TC90522)
Tuner: Next version of Sharp QM1D1C0042
em28xx_dvb_init(): add init code for PLEX PX-BCUD with calling
px_bcud_init() that does things like pin configuration.
qm1d1c0042_init(): support the next version of QM1D1C0042, change to
choose an appropriate array of initial registers by reading chip id.
[mchehab@osg.samsung.com: fold a fixup patch and fix checkpatch.pl
errors/warnings, where applicable]
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Fixes: 0f433fa0ec ("mlxsw: spectrum_buffers: Implement shared buffer configuration")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we fail to set the flooding configuration for the broadcast and
unregistered multicast traffic, we should revert the flooding
configuration of the unknown unicast traffic.
Fixes: 0293038e0c36 ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the leave procedure in the error path symmetric to the join
procedure and first remove the port from the collector before
potentially destroying the LAG.
Fixes: 0d65fc13042f ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Armada CP110 system controller provides, amongst other things, a
number of clocks for the platform: a small number of core clocks, and
then a number of gatable clocks, derived from some of the core
clocks. Those clocks are configured via registers of the CP110 System
Controller.
The CP110 is the other core HW block (next to the AP806) used in the
Marvel Armada 7K and 8K SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[sboyd@codeaurora.org: Silence some checkpatch noise]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
UDP tunnel segmentation code relies on the inner offsets being set for
an UDP tunnel GSO packet, but the inner *_complete() functions will
set the inner offsets only if 'encapsulation' is set before calling
them. Currently, udp_gro_complete() sets 'encapsulation' only after
the inner *_complete() functions are done. This causes the inner
offsets having invalid values after udp_gro_complete() returns, which
in turn will make it impossible to properly segment the packet in case
it needs to be forwarded, which would be visible to the user either as
invalid packets being sent or as packet loss.
This patch fixes this by setting skb's 'encapsulation' in
udp_gro_complete() before calling into the inner complete functions,
and by making each possible UDP tunnel gro_complete() callback set the
inner_mac_header to the beginning of the tunnel payload.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Reviewed-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The setting of the UDP tunnel GSO type is already performed by
udp[46]_gro_complete().
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating macvtaps that are expected to have the same ifindex
in different network namespaces, only the first one will succeed.
The others will fail with a sysfs_warn_dup warning due to them trying
to create the following sysfs link (with 'NN' the ifindex of macvtapX):
/sys/class/macvtap/tapNN -> /sys/devices/virtual/net/macvtapX/tapNN
This is reproducible by running the following commands:
ip netns add ns1
ip netns add ns2
ip link add veth0 type veth peer name veth1
ip link set veth0 netns ns1
ip link set veth1 netns ns2
ip netns exec ns1 ip l add link veth0 macvtap0 type macvtap
ip netns exec ns2 ip l add link veth1 macvtap1 type macvtap
The last command will fail with "RTNETLINK answers: File exists" (along
with the kernel warning) but retrying it will work because the ifindex
was incremented.
The 'net' device class is isolated between network namespaces so each
one has its own hierarchy of net devices.
This isn't the case for the 'macvtap' device class.
The problem occurs half-way through the netdev registration, when
`macvtap_device_event` is called-back to create the 'tapNN' macvtap
class device under the 'macvtapX' net class device.
This patch adds namespace support to the 'macvtap' device class so
that /sys/class/macvtap is no longer shared between net namespaces.
However, making the macvtap sysfs class namespace-aware has the side
effect of changing /sys/devices/virtual/net/macvtapX/tapNN into
/sys/devices/virtual/net/macvtapX/macvtap/tapNN.
This is due to Commit 24b1442 ("Driver-core: Always create class
directories for classses that support namespaces") and the fact that
class devices supporting namespaces are really not supposed to be placed
directly under other class devices.
To avoid breaking userland, a tapNN symlink pointing to macvtap/tapNN is
created inside the macvtapX directory.
Signed-off-by: Marc Angel <marc@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Armada AP806 system controller, amongst other things, provides a
number of clocks for the platform: the CPU cluster clocks, whose
frequencies are found by reading the Sample At Reset register, one
fixed clock, and another clock derived from the fixed clock, which is
the one used by most peripherals in AP806.
The AP806 is one of the two core HW blocks used in the Marvell 7K/8K
SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[sboyd@codeaurora.org: Silence some checkpatch noise]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Make the schedutil cpufreq governor depend on CONFIG_SMP, because
the scheduler-provided utilization numbers used by it are only
available with CONFIG_SMP set.
Fixes: 9bdcb44e391d (cpufreq: schedutil: New governor based on scheduler utilization data)
Reported-by: Steve Muckle <steve.muckle@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
|
|
|
|
* pm-cpufreq-fixes:
intel_pstate: Fix intel_pstate_get()
cpufreq: intel_pstate: Fix HWP on boot CPU after system resume
cpufreq: st: enable selective initialization based on the platform
cpufreq: intel_pstate: Fix processing for turbo activation ratio
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-05
This series contains updates to i40e and i40evf.
The theme behind this series is code reduction, yeah! Jesse provides
most of the changes starting with a refactor of the interpretation of
a tunnel which lets us start using the hardware's parsing. Removed
the packet split receive routine and ancillary code in preparation
for the Rx-refactor. The refactor of the receive routine,
aligns the receive routine with the one in ixgbe which was highly
optimized. The hardware supports a 16 byte descriptor for receive,
but the driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole lot
of complexity while getting rid of the code. Fixed a bug where while
changing the number of descriptors using ethtool, the driver did not
test the limits of the system memory before permanently assuming it
would be able to get receive buffer memory.
Mitch fixes a memory leak of one page each time the driver is opened by
allocating the correct number of receive buffers and do not fiddle with
next_to_use in the VF driver.
Arnd Bergmann fixed a indentation issue by adding the appropriate
curly braces in i40e_vc_config_promiscuous_mode_msg().
Julia Lawall fixed an issue found by Coccinelle, where i40e_client_ops
structure can be const since it is never modified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for Intel Bluetooth device 8265 also known
as Windstorm Peak (WsP).
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0a2b Rev= 0.10
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Tables have to exist for VRFs to function. Ensure they exist
when VRF device is created.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qede requires qed to provide enough resources to accommodate 16 combined
channels, but that upper-bound isn't actually being enforced by it.
Instead, qed inform back to qede how many channels can be opened based on
available resources - but that calculation doesn't really take into account
the resources requested by qede; Instead it considers other FW/HW available
resources.
As a result, if a user would increase the number of channels to more than
16 [e.g., using ethtool] the chip would hang.
This change increments the resources requested by qede to 64 combined
channels instead of 16; This value is an upper bound on the possible
available channels [due to other FW/HW resources].
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently had a system crash in the cnic module. Vmcore analysis confirmed
that "ip link up" was executed which failed due to an allocation failure
because of memory fragmentation. Futher analysis revealed that the cnic irq
vector was still allocated after the "ip link up" that failed. When
"ip link down" was executed it called free_msi_irqs() which crashed the system
because the cnic irq was still inuse.
PANIC: "kernel BUG at drivers/pci/msi.c:411!"
The code execution was:
cnic_netdev_event()
if (event == NETDEV_UP) {
.
.
▹ if (!cnic_start_hw(dev))
cnic_start_hw()
calls cnic_cm_open() which failed with -ENOMEM
cnic_start_hw() then took the err1 path:
err1:↩
cp->free_resc(dev);↩ <---- frees resources but not irq vector
pci_dev_put(dev->pcidev);↩
return err;↩
}↩
This returns control back to cnic_netdev_event() but now the cnic irq vector
is still allocated even although cnic_cm_open() failed. The next
"ip link down" while trigger the crash.
The cnic_start_hw() routine is not handling the allocation failure correctly.
Fix this by checking whether CNIC_DRV_STATE_HANDLES_IRQ flag is set indicating
that the hardware has been started in cnic_start_hw(). If it has then call
cp->stop_hw() which frees the cnic irq vector and cnic resources. Otherwise
just maintain the previous behaviour and free cnic resources.
I reproduced this by injecting an ENOMEM error into cnic_cm_alloc_mem()s return
code.
# ip link set dev enpX down
# ip link set dev enpX up <--- hit's allocation failure
# ip link set dev enpX down <--- crashes here
With this patch I confirmed there was no crash in the reproducer.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for problems introduced or discovered recently (intel_pstate,
sti-cpufreq, ARM64 cpuidle, Operating Performance Points framework,
generic device properties framework) and one fix for a hotplug-related
deadlock in ACPICA that's been there forever, but is nasty enough.
Specifics:
- Fix for a recent regression in the intel_pstate driver causing it
to fail to restore the HWP (HW-managed P-states) configuration of
the boot CPU after suspend-to-RAM (Rafael Wysocki).
- Fix for two recent regressions in the intel_pstate driver, one that
can trigger a divide by zero if the driver is accessed via sysfs
before it manages to take the first sample and one causing it to
fail to update a structure field used in a trace point, so the
information coming from it is less useful (Rafael Wysocki).
- Fix for a problem in the sti-cpufreq driver introduced during the
4.5 cycle that causes it to break CPU PM in multi-platform kernels
by registering cpufreq-dt (which subsequently doesn't work)
unconditionally and preventing the driver that would actually work
from registering (Sudeep Holla).
- Stable-candidate fix for an ARM64 cpuidle issue causing idle state
usage counters to be incorrectly updated for idle states that were
not entered due to errors (James Morse).
- Fix for a recently introduced issue in the OPP (Operating
Performance Points) framework causing it to print bogus error
messages for missing optional regulators (Viresh Kumar).
- Fix for a recently introduced issue in the generic device
properties framework that may cause it to attempt to dereferece and
invalid pointer in some cases (Heikki Krogerus).
- Fix for a deadlock in the ACPICA core that may be triggered by
device (eg Thunderbolt) hotplug (Prarit Bhargava)"
* tag 'pm+acpi-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / OPP: Remove useless check
ACPICA: Dispatcher: Update thread ID for recursive method calls
intel_pstate: Fix intel_pstate_get()
cpufreq: intel_pstate: Fix HWP on boot CPU after system resume
cpufreq: st: enable selective initialization based on the platform
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
device property: Avoid potential dereferences of invalid pointers
|
|
Another version of Elgato EyeTV Sat USB DVB-S2 adapter needs just
a USB ID addition.
Signed-off-by: Christian Knippel <namerp@gmail.com>
Reported-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
It's been reported that CJC7113 devices are returning
all 1s when reading register 0:
"1111111111111111" found @ 0x4a (stk1160)
This new device is apparently compatible with SA7113, so let's
add a quirk to allow its autodetection. Given there isn't
any known differences with SAA7113, this commit does not
introduces a new saa711x_model value.
Reported-by: Philippe Desrochers <desrochers.philippe@gmail.com>
Signed-off-by: Kevin Fitch <kfitch42@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The nvm_dev->max_pages_per_blk variable was removed in favor of the new
nvm->sec_per_blk variable. The ->max_pages_per_blk variable was still
used in rrpc_capacity, reporting the reserved capacity to zero. Replace
with ->sec_per_blk to calculate the reserved area again.
Signed-off-by: Javier González <javier@cnexlabs.com>
Updated patch description. Was "lightnvm: eliminate redundant variable"
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The number of ppas contained on a request is not necessarily the number
of pages that it maps to neither on the target nor on the device side.
In order to avoid confusion, rename nr_pages to nr_ppas since it is what
the variable actually contains.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Targets can update a block state when having a reference to an
in-memory virtual block. In the case that a target does not keep the
block metadata in memory, it does not have a way to update this
structure.
Therefore, expose gennvm_mark_blk() through the media managers
->mark_blk() callback and let targets update the state structure through
this callback.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Targets associated with a device manager are not freed on device
removal. They have to be manually removed before shutdown. Make sure
any outstanding targets are freed upon shutdown.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A recent change to lightnvm added code to pass a kernel pointer
to the hardware, which gcc complained about:
drivers/nvme/host/lightnvm.c: In function 'nvme_nvm_rqtocmd':
drivers/nvme/host/lightnvm.c:472:32: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
c->ph_rw.metadata = cpu_to_le64(rqd->meta_list);
It looks like this has no way of working anyway, so this changes
the code to pass the dma_address instead. This was most likely
what was intended here. Neither of the two are currently ever
written to, so the effect is the same for now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a34b1eb78e21 ("lightnvm: enable metadata to be sent to device")
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
When doing GC, rrpc calculates the physical LUN to which the rrpc block
belongs too. This calculation is based on the assumption that LUNs are
assigned sequentially to the LUN list. Use the reference to the LUN
instead. This saves us the calculation and allows us to align LUNs in a
different manner to, for example, take advantage of devide parallelism.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Align with the rest of the nvme subsystem.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Until now, the dma pool have been exclusively used to allocate the ppa
list being sent to the device. In pblk (upcoming), we use these pools to
allocate metadata too. Thus, we generalize the names of some variables
on the dma helper functions to make the code more readable.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Enable metadata buffer to be sent to the device through the metadata
field on the physical rw nvme command. The size of the metadata buffer
must follow dev->oob_size * # of PPAs.
Signed-off-by: Javier González <javier@cnexlabs.com>
Updated description.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
rrpc does not save any metadata on a given request. Thus, do not attempt
to free the metadata dma region.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The ppa configured for retrieving the bad block table uses the internal
lun id to setup the get bad block ppa. This increases monotonically
with the number luns available. When configuring a ppa, the channel and
lun must be specified separately, leading to an out of bound memory
access in gennvm_block_bb when lun id goes beyond the luns available
within a channel.
Additional, remove out of bound check in gennvm_block_bb(), as it was a
buggy to begin with.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The set_bb_tbl takes struct nvm_rq and only uses its ppa_list and
nr_pages internally. Instead, make these two variables explicit.
This allows a user to call it without initializing a struct nvm_rq
first.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We move the responsibility of managing the persistent bad block table to
the target. The target may choose to mark a block bad or retry writing
to it. Never the less, it should be the target that makes the decision
and not the media manager.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A virtual block enables a block to identify multiple physical blocks.
This is useful for metadata where a device media supports multiple
planes. In that case, a block, with multiple planes can be managed
as a single vblk. Reducing the metadata required by one forth.
nvm_set_rqd_ppalist() takes care of expanding a ppa_list with vblks
automatically. However, for some use-cases, where only a single physical
block is required, the ppa_list should not be expanded.
Therefore, add a vblk parameter to nvm_set_rqd_ppalist(), and only
expand the ppa_list if vblk is set.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Now that device ops->get_bb_table no longer uses a callback, the
struct factory_blks can be removed.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The device ops->get_bb_tbl() takes a callback, that allows the caller
to use its own callback function to update its data structures in the
returning function.
This makes it difficult to send parameters to the callback, and usually
is circumvented by small private structures, that both carry the callers
state and any flags needed to fulfill the update.
Refactor ops->get_bb_tbl() to fill a data buffer with the status of the
blocks returned, and let the user call the callback function manually.
That will provide the necessary flags and data structures and simplify
the logic around ops->get_bb_tbl().
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Users that wish to iterate all luns on a device. Must create a
struct ppa_addr and separate iterators for channels and luns. To set the
iterators, two loops are required, one to iterate channels, and another
to iterate luns. This leads to decrease in readability.
Introduce nvm_for_each_lun_ppa, which implements the nested loop and
sets ppa, channel, and lun variable for each loop body, eliminating
the boilerplate code.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A target name must be unique. However, a per-device registration of
targets is maintained on a dev->online_targets list, with a per-device
search for targets upon registration.
This results in a name collision when two targets, with the same name,
are created on two different targets, where the per-device list is not
shared.
Signed-off-by: Simon A. F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The functions nvm_register_target(), nvm_unregister_target() and
associated list refers to a target type that is being registered by a
target type module. Rename nvm_*_targets() to nvm_*_tgt_type(), so that
the intension is clear.
This enables target instances to use the _nvm_*_targets() naming.
Signed-off-by: Simon A. F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Since we mainly use soffset in device sector size, we therefore store
this value in rrpc->soffset, instead of the offset in 512byte sector
size. This eliminates the "(ilog2(dev->sec_size) - 9)" calculation on
each I/O.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Updated patch description.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Calculate rrpc total blocks and sectors up front, make sense
to use them. For example, we use rrpc->nr_sects to calculate rrpc
area size, but it makes no sense if we don't initialize it up front,
since it would be zero until we finish rrpc luns init.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A memory leak occurs if the lower page table is initialized and the
following dev->lun_map fails on allocation.
Rearrange the initialization of lower page table to allow dev->lun_map
to fail gracefully without memory leak.
Reviewed by: Johannes Thumshirn <jthumshirn@suse.de>
Move kfree of dev->lun_map to nvm_free()
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The get block table command returns a list of blocks and planes
with their associated state. Users, such as gennvm and sysblk,
manages all planes as a single virtual block.
It was therefore natural to fold the bad block list before it is
returned. However, to allow users, which manages on a per-plane
block level, to also use the interface, the get_bb_tbl interface is
changed to not fold by default and instead let the caller fold if
necessary.
Reviewed by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The flash page size (fpg) and size across planes (pfpg) are convenient
to know when allocating buffer sizes. This has previously been a
calculated in various places. Replace with the pre-calculated values.
Reviewed by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The nvm_submit_ppa function assumes that users manage all plane
blocks as a single block. Extend the API with nvm_submit_ppa_list
to allow the user to send its own ppa list. If the user submits more
than a single PPA, the user must take care to allocate and free
the corresponding ppa list.
Reviewed by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The device ->submit_io() callback might fail to submit I/O to device.
In that case, the nvm_submit_ppa function should not wait for
completion. Instead return the ->submit_io() error.
Reviewed by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This fixes the following warnings:
drivers/lightnvm/sysblk.c:125:9: warning: ‘ret’ may be used
uninitialized in this function
drivers/lightnvm/sysblk.c:275:15: warning: ‘ret’ may be used
uninitialized in this function
In both cases, ret is only set from within a loop that may not be entered.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
By default, rproc_fw_boot() needs to wait for rproc to be configured,
but a race may occur when using rpmsg/virtio. In this case, it can
be called locally in a safe manor.
This patch represents two usecases:
- External call (via exported rproc_boot()), which waits
- Internal call can use 'nowait' version of rproc_boot()
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
