| Age | Commit message (Collapse) | Author |
|---|
|
We normally runtime suspend when there are displays attached if they
are in the DPMS off state, however, if something wakes the GPU
we send a hotplug event on resume (in case any displays were connected
while the GPU was in suspend) which can cause userspace to light
up the displays again soon after they were turned off.
Prior to
commit 087451f372bf76 ("drm/amdgpu: use generic fb helpers instead of setting up AMD own's."),
the driver took a runtime pm reference when the fbdev emulation was
enabled because we didn't implement proper shadowing support for
vram access when the device was off so the device never runtime
suspended when there was a console bound. Once that commit landed,
we now utilize the core fb helper implementation which properly
handles the emulation, so runtime pm now suspends in cases where it did
not before. Ultimately, we need to sort out why runtime suspend in not
working in this case for some users, but this should restore similar
behavior to before.
v2: move check into runtime_suspend
v3: wake ups -> wakeups in comment, retain pm_runtime behavior in
runtime_idle callback
Fixes: 087451f372bf76 ("drm/amdgpu: use generic fb helpers instead of setting up AMD own's.")
Link: https://lore.kernel.org/r/20220403132322.51c90903@darkstar.example.org/
Tested-by: Michele Ballabio <ballabio.m@gmail.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Add support to checkpoint/restore GWS (Global Wave Sync) queues.
Signed-off-by: David Yat Sin <david.yatsin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
dqm->gws_queue_count and pdd->qpd.mapped_gws_queue need to be updated
each time the queue gets evicted.
Fixes: b8020b0304c8 ("drm/amdkfd: Enable over-subscription with >1 GWS queue")
Signed-off-by: David Yat Sin <david.yatsin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The Sapphire Rapids (SPR) C6 optimization was added to the end of the
'spr_idle_state_table_update()' function. However, the function has a
'return' which may happen before the optimization has a chance to run.
And this may prevent the optimization from happening.
This is an unlikely scenario, but possible if user boots with, say,
the 'intel_idle.preferred_cstates=6' kernel boot option.
This patch fixes the issue by eliminating the problematic 'return'
statement.
Fixes: 3a9cf77b60dc ("intel_idle: add core C6 optimization for SPR")
Suggested-by: Jan Beulich <jbeulich@suse.com>
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ rjw: Minor changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Problem description.
When user boots kernel up with the 'intel_idle.preferred_cstates=4' option,
we enable C1E and disable C1 states on Sapphire Rapids Xeon (SPR). In order
for C1E to work on SPR, we have to enable the C1E promotion bit on all
CPUs. However, we enable it only on one CPU.
Fix description.
The 'intel_idle' driver already has the infrastructure for disabling C1E
promotion on every CPU. This patch uses the same infrastructure for
enabling C1E promotion on every CPU. It changes the boolean
'disable_promotion_to_c1e' variable to a tri-state 'c1e_promotion'
variable.
Tested on a 2-socket SPR system. I verified the following combinations:
* C1E promotion enabled and disabled in BIOS.
* Booted with and without the 'intel_idle.preferred_cstates=4' kernel
argument.
In all 4 cases C1E promotion was correctly set on all CPUs.
Also tested on an old Broadwell system, just to make sure it does not cause
a regression. C1E promotion was correctly disabled on that system, both C1
and C1E were exposed (as expected).
Fixes: da0e58c038e6 ("intel_idle: add 'preferred_cstates' module argument")
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ rjw: Minor changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull ARM cpufreq fixes for 5.18-rc5 from Viresh Kumar:
"- Fix issues with the Qualcomm's cpufreq driver (Dmitry Baryshkov and
Vladimir Zapolskiy).
- Fix memory leak with the Sun501 driver (Xiaobing Luo)."
* tag 'cpufreq-arm-fixes-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: qcom-cpufreq-hw: Clear dcvs interrupts
cpufreq: fix memory leak in sun50i_cpufreq_nvmem_probe
cpufreq: qcom-cpufreq-hw: Fix throttle frequency value on EPSS platforms
cpufreq: qcom-hw: provide online/offline operations
cpufreq: qcom-hw: fix the opp entries refcounting
cpufreq: qcom-hw: fix the race between LMH worker and cpuhp
cpufreq: qcom-hw: drop affinity hint before freeing the IRQ
|
|
Commit e8604b1447b4 introduced a call to the helper function
msi_first_desc(), which needs MSI descriptor mutex lock before
call. However, the required mutex lock was not added. This results in
lockdep assertion:
WARNING: CPU: 4 PID: 119 at kernel/irq/msi.c:274 msi_first_desc+0xd0/0x10c
msi_first_desc+0xd0/0x10c
fsl_mc_msi_domain_alloc_irqs+0x7c/0xc0
fsl_mc_populate_irq_pool+0x80/0x3cc
Fix this by adding the mutex lock and unlock around the function call.
Fixes: e8604b1447b4 ("bus: fsl-mc-msi: Simplify MSI descriptor handling")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220412075636.755454-1-shinichiro.kawasaki@wdc.com
|
|
Current DP driver implementation has adding safe mode done at
dp_hpd_plug_handle() which is expected to be executed under event
thread context.
However there is possible circular locking happen (see blow stack trace)
after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which
is executed under drm_thread context.
After review all possibilities methods and as discussed on
https://patchwork.freedesktop.org/patch/483155/, supporting EDID
compliance tests in the driver is quite hacky. As seen with other
vendor drivers, supporting these will be much easier with IGT. Hence
removing all the related fail safe code for it so that no possibility
of circular lock will happen.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
======================================================
WARNING: possible circular locking dependency detected
5.15.35-lockdep #6 Tainted: G W
------------------------------------------------------
frecon/429 is trying to acquire lock:
ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at:
dp_panel_add_fail_safe_mode+0x4c/0xa0
but task is already holding lock:
ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: lock_crtcs+0xb4/0x124
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&kms->commit_lock[i]){+.+.}-{3:3}:
__mutex_lock_common+0x174/0x1a64
mutex_lock_nested+0x98/0xac
lock_crtcs+0xb4/0x124
msm_atomic_commit_tail+0x330/0x748
commit_tail+0x19c/0x278
drm_atomic_helper_commit+0x1dc/0x1f0
drm_atomic_commit+0xc0/0xd8
drm_atomic_helper_set_config+0xb4/0x134
drm_mode_setcrtc+0x688/0x1248
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
-> #2 (crtc_ww_class_mutex){+.+.}-{3:3}:
__mutex_lock_common+0x174/0x1a64
ww_mutex_lock+0xb8/0x278
modeset_lock+0x304/0x4ac
drm_modeset_lock+0x4c/0x7c
drmm_mode_config_init+0x4a8/0xc50
msm_drm_init+0x274/0xac0
msm_drm_bind+0x20/0x2c
try_to_bring_up_master+0x3dc/0x470
__component_add+0x18c/0x3c0
component_add+0x1c/0x28
dp_display_probe+0x954/0xa98
platform_probe+0x124/0x15c
really_probe+0x1b0/0x5f8
__driver_probe_device+0x174/0x20c
driver_probe_device+0x70/0x134
__device_attach_driver+0x130/0x1d0
bus_for_each_drv+0xfc/0x14c
__device_attach+0x1bc/0x2bc
device_initial_probe+0x1c/0x28
bus_probe_device+0x94/0x178
deferred_probe_work_func+0x1a4/0x1f0
process_one_work+0x5d4/0x9dc
worker_thread+0x898/0xccc
kthread+0x2d4/0x3d4
ret_from_fork+0x10/0x20
-> #1 (crtc_ww_class_acquire){+.+.}-{0:0}:
ww_acquire_init+0x1c4/0x2c8
drm_modeset_acquire_init+0x44/0xc8
drm_helper_probe_single_connector_modes+0xb0/0x12dc
drm_mode_getconnector+0x5dc/0xfe8
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
-> #0 (&dev->mode_config.mutex){+.+.}-{3:3}:
__lock_acquire+0x2650/0x672c
lock_acquire+0x1b4/0x4ac
__mutex_lock_common+0x174/0x1a64
mutex_lock_nested+0x98/0xac
dp_panel_add_fail_safe_mode+0x4c/0xa0
dp_hpd_plug_handle+0x1f0/0x280
dp_bridge_enable+0x94/0x2b8
drm_atomic_bridge_chain_enable+0x11c/0x168
drm_atomic_helper_commit_modeset_enables+0x500/0x740
msm_atomic_commit_tail+0x3e4/0x748
commit_tail+0x19c/0x278
drm_atomic_helper_commit+0x1dc/0x1f0
drm_atomic_commit+0xc0/0xd8
drm_atomic_helper_set_config+0xb4/0x134
drm_mode_setcrtc+0x688/0x1248
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
Changes in v2:
-- re text commit title
-- remove all fail safe mode
Changes in v3:
-- remove dp_panel_add_fail_safe_mode() from dp_panel.h
-- add Fixes
Changes in v5:
-- to=dianders@chromium.org
Changes in v6:
-- fix Fixes commit ID
Fixes: 8b2c181e3dcf ("drm/msm/dp: add fail safe mode outside of event_mutex context")
Reported-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Link: https://lore.kernel.org/r/1651007534-31842-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"Core fix:
- Fix a possible data corruption of the 'part' field in mtd_info
Rawnand fixes:
- Fix the check on the return value of wait_for_completion_timeout
- Fix wrong ECC parameters for mt7622
- Fix a possible memory corruption that might panic in the Qcom
driver"
* tag 'mtd/fixes-for-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: qcom: fix memory corruption that causes panic
mtd: fix 'part' field data corruption in mtd_info
mtd: rawnand: Fix return value check of wait_for_completion_timeout
mtd: rawnand: fix ecc parameters for mt7622
|
|
Minh Yuan reported a concurrency use-after-free issue in the floppy code
between raw_cmd_ioctl and seek_interrupt.
[ It turns out this has been around, and that others have reported the
KASAN splats over the years, but Minh Yuan had a reproducer for it and
so gets primary credit for reporting it for this fix - Linus ]
The problem is, this driver tends to break very easily and nowadays,
nobody is expected to use FDRAWCMD anyway since it was used to
manipulate non-standard formats. The risk of breaking the driver is
higher than the risk presented by this race, and accessing the device
requires privileges anyway.
Let's just add a config option to completely disable this ioctl and
leave it disabled by default. Distros shouldn't use it, and only those
running on antique hardware might need to enable it.
Link: https://lore.kernel.org/all/000000000000b71cdd05d703f6bf@google.com/
Link: https://lore.kernel.org/lkml/CAKcFiNC=MfYVW-Jt9A3=FPJpTwCD2PL_ULNCpsCVE5s8ZeBQgQ@mail.gmail.com
Link: https://lore.kernel.org/all/CAEAjamu1FRhz6StCe_55XY5s389ZP_xmCF69k987En+1z53=eg@mail.gmail.com
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
Reported-by: syzbot+8e8958586909d62b6840@syzkaller.appspotmail.com
Reported-by: cruise k <cruise4k@gmail.com>
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Tested-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sparse reports this issue
core.c: note: in included file:
core.h:239:12: warning: symbol 'pmc_lpm_modes' was not declared. Should it be static?
Global variables should not be defined in headers. This only works
because core.h is only included by core.c. Single file use
variables should be static, so change its storage-class specifier
to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20220423123048.591405-1-trix@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Fix bug that added an offset to the mailbox addr during multi-packet
reads. Did not affect current ABI since it doesn't support multi-packet
transactions.
Fixes: 2546c6000430 ("platform/x86: Add Intel Software Defined Silicon driver")
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20220420155622.1763633-4-david.e.box@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Due to change in firmware flow, update mailbox writes to poll on ready bit
instead of run_busy bit. This change makes the polling method consistent
for both writes and reads, which also uses the ready bit.
Fixes: 2546c6000430 ("platform/x86: Add Intel Software Defined Silicon driver")
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20220420155622.1763633-3-david.e.box@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
To prevent an agent from indefinitely holding the mailbox firmware has
implemented a leaky bucket algorithm. Repeated access to the mailbox may
now incur a delay of up to 2.1 seconds. Add a retry loop that tries for
up to 2.5 seconds to acquire the mailbox.
Fixes: 2546c6000430 ("platform/x86: Add Intel Software Defined Silicon driver")
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20220420155622.1763633-2-david.e.box@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Loading this driver in guests results in unchecked MSR access error for
MSR 0x620.
There is no use of reading and modifying package/die scope uncore MSRs
in guests. So check for CPU feature X86_FEATURE_HYPERVISOR to prevent
loading of this driver in guests.
Fixes: dbce412a7733 ("platform/x86/intel-uncore-freq: Split common and enumeration part")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215870
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20220427100304.2562990-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This works on my system.
Signed-off-by: Darryn Anton Jordan <darrynjordan@icloud.com>
Acked-by: Thomas Weißschuh <thomas@weissschuh.net>
Link: https://lore.kernel.org/r/Ylguq87YG+9L3foV@hark
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Latitude 7520 supports AC timeouts, but it has no KBD_LED_AC_TOKEN
and so changes to stop_timeout appear to have no effect if the laptop
is plugged in.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220426120827.12363-1-gabriele.mzt@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
fails
Before this commit fan_curve_check_present() was trying to not cause
the probe to fail on devices without fan curve control by testing for
known error codes returned by asus_wmi_evaluate_method_buf().
Checking for ENODATA or ENODEV, with the latter being returned by this
function when an ACPI integer with a value of ASUS_WMI_UNSUPPORTED_METHOD
is returned. But for other ACPI integer returns this function just returns
them as is, including the ASUS_WMI_DSTS_UNKNOWN_BIT value of 2.
On the Asus U36SD ASUS_WMI_DSTS_UNKNOWN_BIT gets returned, leading to:
asus-nb-wmi: probe of asus-nb-wmi failed with error 2
Instead of playing whack a mole with error codes here, simply treat all
errors as there not being any fan curves, fixing the driver no longer
loading on the Asus U36SD laptop.
Fixes: e3d13da7f77d ("platform/x86: asus-wmi: Fix regression when probing for fan curve control")
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2079125
Cc: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220427114956.332919-1-hdegoede@redhat.com
|
|
asus_wmi_evaluate_method_buf()
This code tests for if the obj->buffer.length is larger than the buffer
but then it just does the memcpy() anyway.
Fixes: 0f0ac158d28f ("platform/x86: asus-wmi: Add support for custom fan curves")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220413073744.GB8812@kili
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
CLEAR_FAULTS commands can apparently sometimes trigger catastrophic
power output glitches on the ahe-50dc, so block them from being sent
at all.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220427035109.3819-1-zev@bewilderbeest.net
Fixes: d387d88ed045 ("hwmon: (pmbus) Add Delta AHE-50DC fan control module driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-04-26
This series contains updates to ice driver only.
Ivan Vecera removes races related to VF message processing by changing
mutex_trylock() call to mutex_lock() and moving additional operations
to occur under mutex.
Petr Oros increases wait time after firmware flash as current time is
not sufficient.
Jake resolves a use-after-free issue for mailbox snapshot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining
GSWIP_MII_CFG bits") added all known bits in the GSWIP_MII_CFGp
register. It helped bring this register into a well-defined state so the
driver has to rely less on the bootloader to do things right.
Unfortunately it also sets the GSWIP_MII_CFG_RMII_CLK bit without any
possibility to configure it. Upon further testing it turns out that all
boards which are supported by the GSWIP driver in OpenWrt which use an
RMII PHY have a dedicated oscillator on the board which provides the
50MHz RMII reference clock.
Don't set the GSWIP_MII_CFG_RMII_CLK bit (but keep the code which always
clears it) to fix support for the Fritz!Box 7362 SL in OpenWrt. This is
a board with two Atheros AR8030 RMII PHYs. With the "RMII clock" bit set
the MAC also generates the RMII reference clock whose signal then
conflicts with the signal from the oscillator on the board. This results
in a constant cycle of the PHY detecting link up/down (and as a result
of that: the two ports using the AR8030 PHYs are not working).
At the time of writing this patch there's no known board where the MAC
(GSWIP) has to generate the RMII reference clock. If needed this can be
implemented in future by providing a device-tree flag so the
GSWIP_MII_CFG_RMII_CLK bit can be toggled per port.
Fixes: 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits")
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20220425152027.2220750-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix some register offsets on Intel Alderlake
- Fix the order the UFS and SDC pins on Qualcomm SM6350
- Fix a build error in Mediatek Moore.
- Fix a pin function table in the Sunplus SP7021.
- Fix some Kconfig and static keywords on the Samsung Tesla FSD SoC.
- Fix up the EOI function for edge triggered IRQs and keep the block
clock enabled for level IRQs in the STM32 driver.
- Fix some bits and order in the Rockchip RK3308 driver.
- Handle the errorpath in the Pistachio driver probe() properly.
* tag 'pinctrl-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pistachio: fix use of irq_of_parse_and_map()
pinctrl: stm32: Keep pinctrl block clock enabled when LEVEL IRQ requested
pinctrl: rockchip: sort the rk3308_mux_recalced_data entries
pinctrl: rockchip: fix RK3308 pinmux bits
pinctrl: stm32: Do not call stm32_gpio_get() for edge triggered IRQs in EOI
pinctrl: Fix an error in pin-function table of SP7021
pinctrl: samsung: fix missing GPIOLIB on ARM64 Exynos config
pinctrl: mediatek: moore: Fix build error
pinctrl: qcom: sm6350: fix order of UFS & SDC pins
pinctrl: alderlake: Fix register offsets for ADL-N variant
pinctrl: samsung: staticize fsd_pin_ctrl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes and updates from Helge Deller:
"A bunch of outstanding fbdev patches - all trivial and small"
* tag 'for-5.18/fbdev-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
video: fbdev: clps711x-fb: Use syscon_regmap_lookup_by_phandle
video: fbdev: mmp: replace usage of found with dedicated list iterator variable
video: fbdev: sh_mobile_lcdcfb: Remove sh_mobile_lcdc_check_var() declaration
video: fbdev: i740fb: Error out if 'pixclock' equals zero
video: fbdev: i740fb: use memset_io() to clear screen
video: fbdev: s3fb: Error out if 'pixclock' equals zero
video: fbdev: arkfb: Error out if 'pixclock' equals zero
video: fbdev: tridentfb: Error out if 'pixclock' equals zero
video: fbdev: vt8623fb: Error out if 'pixclock' equals zero
video: fbdev: kyro: Error out if 'lineclock' equals zero
video: fbdev: neofb: Fix the check of 'var->pixclock'
video: fbdev: imxfb: Fix missing of_node_put in imxfb_probe
video: fbdev: omap: Make it CCF clk API compatible
video: fbdev: aty/matrox/...: Prepare cleanup of powerpc's asm/prom.h
video: fbdev: pm2fb: Fix a kernel-doc formatting issue
linux/fb.h: Spelling s/palette/palette/
video: fbdev: sis: fix potential NULL dereference in sisfb_post_sis300()
video: fbdev: pxafb: use if else instead
video: fbdev: udlfb: properly check endpoint type
video: fbdev: of: display_timing: Remove a redundant zeroing of memory
|
|
During ice_sriov_configure, if num_vfs is 0, we are being asked by the
kernel to remove all VFs.
The driver first de-initializes the snapshot before freeing all the VFs.
This results in a use-after-free BUG detected by KASAN. The bug occurs
because the snapshot can still be accessed until all VFs are removed.
Fix this by freeing all the VFs first before calling
ice_mbx_deinit_snapshot.
[ +0.032591] ==================================================================
[ +0.000021] BUG: KASAN: use-after-free in ice_mbx_vf_state_handler+0x1c3/0x410 [ice]
[ +0.000315] Write of size 28 at addr ffff889908eb6f28 by task kworker/55:2/1530996
[ +0.000029] CPU: 55 PID: 1530996 Comm: kworker/55:2 Kdump: loaded Tainted: G S I 5.17.0-dirty #1
[ +0.000022] Hardware name: Dell Inc. PowerEdge R740/0923K0, BIOS 1.6.13 12/17/2018
[ +0.000013] Workqueue: ice ice_service_task [ice]
[ +0.000279] Call Trace:
[ +0.000012] <TASK>
[ +0.000011] dump_stack_lvl+0x33/0x42
[ +0.000030] print_report.cold.13+0xb2/0x6b3
[ +0.000028] ? ice_mbx_vf_state_handler+0x1c3/0x410 [ice]
[ +0.000295] kasan_report+0xa5/0x120
[ +0.000026] ? __switch_to_asm+0x21/0x70
[ +0.000024] ? ice_mbx_vf_state_handler+0x1c3/0x410 [ice]
[ +0.000298] kasan_check_range+0x183/0x1e0
[ +0.000019] memset+0x1f/0x40
[ +0.000018] ice_mbx_vf_state_handler+0x1c3/0x410 [ice]
[ +0.000304] ? ice_conv_link_speed_to_virtchnl+0x160/0x160 [ice]
[ +0.000297] ? ice_vsi_dis_spoofchk+0x40/0x40 [ice]
[ +0.000305] ice_is_malicious_vf+0x1aa/0x250 [ice]
[ +0.000303] ? ice_restore_all_vfs_msi_state+0x160/0x160 [ice]
[ +0.000297] ? __mutex_unlock_slowpath.isra.15+0x410/0x410
[ +0.000022] ? ice_debug_cq+0xb7/0x230 [ice]
[ +0.000273] ? __kasan_slab_alloc+0x2f/0x90
[ +0.000022] ? memset+0x1f/0x40
[ +0.000017] ? do_raw_spin_lock+0x119/0x1d0
[ +0.000022] ? rwlock_bug.part.2+0x60/0x60
[ +0.000024] __ice_clean_ctrlq+0x3a6/0xd60 [ice]
[ +0.000273] ? newidle_balance+0x5b1/0x700
[ +0.000026] ? ice_print_link_msg+0x2f0/0x2f0 [ice]
[ +0.000271] ? update_cfs_group+0x1b/0x140
[ +0.000018] ? load_balance+0x1260/0x1260
[ +0.000022] ? ice_process_vflr_event+0x27/0x130 [ice]
[ +0.000301] ice_service_task+0x136e/0x1470 [ice]
[ +0.000281] process_one_work+0x3b4/0x6c0
[ +0.000030] worker_thread+0x65/0x660
[ +0.000023] ? __kthread_parkme+0xe4/0x100
[ +0.000021] ? process_one_work+0x6c0/0x6c0
[ +0.000020] kthread+0x179/0x1b0
[ +0.000018] ? kthread_complete_and_exit+0x20/0x20
[ +0.000022] ret_from_fork+0x22/0x30
[ +0.000026] </TASK>
[ +0.000018] Allocated by task 10742:
[ +0.000013] kasan_save_stack+0x1c/0x40
[ +0.000018] __kasan_kmalloc+0x84/0xa0
[ +0.000016] kmem_cache_alloc_trace+0x16c/0x2e0
[ +0.000015] intel_iommu_probe_device+0xeb/0x860
[ +0.000015] __iommu_probe_device+0x9a/0x2f0
[ +0.000016] iommu_probe_device+0x43/0x270
[ +0.000015] iommu_bus_notifier+0xa7/0xd0
[ +0.000015] blocking_notifier_call_chain+0x90/0xc0
[ +0.000017] device_add+0x5f3/0xd70
[ +0.000014] pci_device_add+0x404/0xa40
[ +0.000015] pci_iov_add_virtfn+0x3b0/0x550
[ +0.000016] sriov_enable+0x3bb/0x600
[ +0.000013] ice_ena_vfs+0x113/0xa79 [ice]
[ +0.000293] ice_sriov_configure.cold.17+0x21/0xe0 [ice]
[ +0.000291] sriov_numvfs_store+0x160/0x200
[ +0.000015] kernfs_fop_write_iter+0x1db/0x270
[ +0.000018] new_sync_write+0x21d/0x330
[ +0.000013] vfs_write+0x376/0x410
[ +0.000013] ksys_write+0xba/0x150
[ +0.000012] do_syscall_64+0x3a/0x80
[ +0.000012] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ +0.000028] Freed by task 10742:
[ +0.000011] kasan_save_stack+0x1c/0x40
[ +0.000015] kasan_set_track+0x21/0x30
[ +0.000016] kasan_set_free_info+0x20/0x30
[ +0.000012] __kasan_slab_free+0x104/0x170
[ +0.000016] kfree+0x9b/0x470
[ +0.000013] devres_destroy+0x1c/0x20
[ +0.000015] devm_kfree+0x33/0x40
[ +0.000012] ice_mbx_deinit_snapshot+0x39/0x70 [ice]
[ +0.000295] ice_sriov_configure+0xb0/0x260 [ice]
[ +0.000295] sriov_numvfs_store+0x1bc/0x200
[ +0.000015] kernfs_fop_write_iter+0x1db/0x270
[ +0.000016] new_sync_write+0x21d/0x330
[ +0.000012] vfs_write+0x376/0x410
[ +0.000012] ksys_write+0xba/0x150
[ +0.000012] do_syscall_64+0x3a/0x80
[ +0.000012] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ +0.000024] Last potentially related work creation:
[ +0.000010] kasan_save_stack+0x1c/0x40
[ +0.000016] __kasan_record_aux_stack+0x98/0xa0
[ +0.000013] insert_work+0x34/0x160
[ +0.000015] __queue_work+0x20e/0x650
[ +0.000016] queue_work_on+0x4c/0x60
[ +0.000015] nf_nat_masq_schedule+0x297/0x2e0 [nf_nat]
[ +0.000034] masq_device_event+0x5a/0x60 [nf_nat]
[ +0.000031] raw_notifier_call_chain+0x5f/0x80
[ +0.000017] dev_close_many+0x1d6/0x2c0
[ +0.000015] unregister_netdevice_many+0x4e3/0xa30
[ +0.000015] unregister_netdevice_queue+0x192/0x1d0
[ +0.000014] iavf_remove+0x8f9/0x930 [iavf]
[ +0.000058] pci_device_remove+0x65/0x110
[ +0.000015] device_release_driver_internal+0xf8/0x190
[ +0.000017] pci_stop_bus_device+0xb5/0xf0
[ +0.000014] pci_stop_and_remove_bus_device+0xe/0x20
[ +0.000016] pci_iov_remove_virtfn+0x19c/0x230
[ +0.000015] sriov_disable+0x4f/0x170
[ +0.000014] ice_free_vfs+0x9a/0x490 [ice]
[ +0.000306] ice_sriov_configure+0xb8/0x260 [ice]
[ +0.000294] sriov_numvfs_store+0x1bc/0x200
[ +0.000015] kernfs_fop_write_iter+0x1db/0x270
[ +0.000016] new_sync_write+0x21d/0x330
[ +0.000012] vfs_write+0x376/0x410
[ +0.000012] ksys_write+0xba/0x150
[ +0.000012] do_syscall_64+0x3a/0x80
[ +0.000012] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ +0.000025] The buggy address belongs to the object at ffff889908eb6f00
which belongs to the cache kmalloc-96 of size 96
[ +0.000016] The buggy address is located 40 bytes inside of
96-byte region [ffff889908eb6f00, ffff889908eb6f60)
[ +0.000026] The buggy address belongs to the physical page:
[ +0.000010] page:00000000b7e99a2e refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1908eb6
[ +0.000016] flags: 0x57ffffc0000200(slab|node=1|zone=2|lastcpupid=0x1fffff)
[ +0.000024] raw: 0057ffffc0000200 ffffea0069d9fd80 dead000000000002 ffff88810004c780
[ +0.000015] raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000
[ +0.000009] page dumped because: kasan: bad access detected
[ +0.000016] Memory state around the buggy address:
[ +0.000012] ffff889908eb6e00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ +0.000014] ffff889908eb6e80: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ +0.000014] >ffff889908eb6f00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ +0.000011] ^
[ +0.000013] ffff889908eb6f80: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ +0.000013] ffff889908eb7000: fa fb fb fb fb fb fb fb fc fc fc fc fa fb fb fb
[ +0.000012] ==================================================================
Fixes: 0891c89674e8 ("ice: warn about potentially malicious VFs")
Reported-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We need to wait 5 s for EMP reset after firmware flash. Code was extracted
from OOT driver (ice v1.8.3 downloaded from sourceforge). Without this
wait, fw_activate let card in inconsistent state and recoverable only
by second flash/activate. Flash was tested on these fw's:
From -> To
3.00 -> 3.10/3.20
3.10 -> 3.00/3.20
3.20 -> 3.00/3.10
Reproducer:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
71: ens7f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
dmesg after flash:
[ 55.120788] ice: Copyright (c) 2018, Intel Corporation.
[ 55.274734] ice 0000:ca:00.0: Get PHY capabilities failed status = -5, continuing anyway
[ 55.569797] ice 0000:ca:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.28.0
[ 55.603629] ice 0000:ca:00.0: Get PHY capability failed.
[ 55.608951] ice 0000:ca:00.0: ice_init_nvm_phy_type failed: -5
[ 55.647348] ice 0000:ca:00.0: PTP init successful
[ 55.675536] ice 0000:ca:00.0: DCB is enabled in the hardware, max number of TCs supported on this port are 8
[ 55.685365] ice 0000:ca:00.0: FW LLDP is disabled, DCBx/LLDP in SW mode.
[ 55.692179] ice 0000:ca:00.0: Commit DCB Configuration to the hardware
[ 55.701382] ice 0000:ca:00.0: 126.024 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x8 link at 0000:c9:02.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
Reboot doesn’t help, only second flash/activate with OOT or patched
driver put card back in consistent state.
After patch:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
19: ens7f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
Fixes: 399e27dbbd9e94 ("ice: support immediate firmware activation via devlink reload")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Previous patch labelled "ice: Fix incorrect locking in
ice_vc_process_vf_msg()" fixed an issue with ignored messages
sent by VF driver but a small race window still left.
Recently caught trace during 'ip link set ... vf 0 vlan ...' operation:
[ 7332.995625] ice 0000:3b:00.0: Clearing port VLAN on VF 0
[ 7333.001023] iavf 0000:3b:01.0: Reset indication received from the PF
[ 7333.007391] iavf 0000:3b:01.0: Scheduling reset task
[ 7333.059575] iavf 0000:3b:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 3
[ 7333.059626] ice 0000:3b:00.0: Invalid message from VF 0, opcode 3, len 4, error -1
Setting of VLAN for VF causes a reset of the affected VF using
ice_reset_vf() function that runs with cfg_lock taken:
1. ice_notify_vf_reset() informs IAVF driver that reset is needed and
IAVF schedules its own reset procedure
2. Bit ICE_VF_STATE_DIS is set in vf->vf_state
3. Misc initialization steps
4. ice_sriov_post_vsi_rebuild() -> ice_vf_set_initialized() and that
clears ICE_VF_STATE_DIS in vf->vf_state
Step 3 is mentioned race window because IAVF reset procedure runs in
parallel and one of its step is sending of VIRTCHNL_OP_GET_VF_RESOURCES
message (opcode==3). This message is handled in ice_vc_process_vf_msg()
and if it is received during the mentioned race window then it's
marked as invalid and error is returned to VF driver.
Protect vf_state check in ice_vc_process_vf_msg() by cfg_lock to avoid
this race condition.
Fixes: e6ba5273d4ed ("ice: Fix race conditions between virtchnl handling and VF ndo ops")
Tested-by: Fei Liu <feliu@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Usage of mutex_trylock() in ice_vc_process_vf_msg() is incorrect
because message sent from VF is ignored and never processed.
Use mutex_lock() instead to fix the issue. It is safe because this
mutex is used to prevent races between VF related NDOs and
handlers processing request messages from VF and these handlers
are running in ice_service_task() context. Additionally move this
mutex lock prior ice_vc_is_opcode_allowed() call to avoid potential
races during allowlist access.
Fixes: e6ba5273d4ed ("ice: Fix race conditions between virtchnl handling and VF ndo ops")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
commit b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a
central place") added a platform device notifier that sets the DMA
offset for all of the display engine frontend and backend devices.
The code applying the offset to DMA buffer physical addresses was then
removed from the backend driver in commit 756668ba682e ("drm/sun4i:
backend: Remove the MBUS quirks"), but the code subtracting PHYS_OFFSET
was left in the frontend driver.
As a result, the offset was applied twice in the frontend driver. This
likely went unnoticed because it only affects specific configurations
(scaling or certain pixel formats) where the frontend is used, on boards
with both one of these older SoCs and more than 1 GB of DRAM.
In addition, the references to PHYS_OFFSET prevent compiling the driver
on architectures where PHYS_OFFSET is not defined.
Fixes: b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a central place")
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-4-samuel@sholland.org
|
|
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Fixes: 7acc9973e3c4 ("usb: phy: generic: add vbus support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220425171412.1188485-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614f3 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Way back in commit 4f25580fb84d ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands
It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.
The aforementioned commit tried to get that right for HS400ES, although
it's unclear whether this ever truly worked as committed into mainline,
as other changes/refactoring adjusted the sequence in conflicting ways:
08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode
switch")
53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode
for mmc")
In any case, today we do step 3 before step 2. Let's fix that, and also
apply the same logic to HS200/400, where this eMMC has problems too.
Resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:
[ 2.058881] mmc1: CQHCI version 5.10
[ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.209804] mmc1: mmc_select_hs400es failed, error -84
[ 2.215597] mmc1: error -84 whilst initialising MMC card
[ 2.417514] mmc1: mmc_select_hs400es failed, error -110
[ 2.423373] mmc1: error -110 whilst initialising MMC card
[ 2.605052] mmc1: mmc_select_hs400es failed, error -110
[ 2.617944] mmc1: error -110 whilst initialising MMC card
[ 2.835884] mmc1: mmc_select_hs400es failed, error -110
[ 2.841751] mmc1: error -110 whilst initialising MMC card
Ealier versions of this patch bumped to 200MHz/HS200 speeds too early,
which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for
the report Luca!) After a second look, it appears that aligns with
JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz)
rates first.
Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode switch")
Fixes: 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Fixes: 4f25580fb84d ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds the necessary PCI IDs for Intel Meteor Lake-P
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220425103518.44028-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We received a report[1] of kernel crashes when Cilium is used in XDP
mode with virtio_net after updating to newer kernels. After
investigating the reason it turned out that when using mergeable bufs
with an XDP program which adjusts xdp.data or xdp.data_meta page_to_buf()
calculates the build_skb address wrong because the offset can become less
than the headroom so it gets the address of the previous page (-X bytes
depending on how lower offset is):
page_to_skb: page addr ffff9eb2923e2000 buf ffff9eb2923e1ffc offset 252 headroom 256
This is a pr_err() I added in the beginning of page_to_skb which clearly
shows offset that is less than headroom by adding 4 bytes of metadata
via an xdp prog. The calculations done are:
receive_mergeable():
headroom = VIRTIO_XDP_HEADROOM; // VIRTIO_XDP_HEADROOM == 256 bytes
offset = xdp.data - page_address(xdp_page) -
vi->hdr_len - metasize;
page_to_skb():
p = page_address(page) + offset;
...
buf = p - headroom;
Now buf goes -4 bytes from the page's starting address as can be seen
above which is set as skb->head and skb->data by build_skb later. Depending
on what's done with the skb (when it's freed most often) we get all kinds
of corruptions and BUG_ON() triggers in mm[2]. We have to recalculate
the new headroom after the xdp program has run, similar to how offset
and len are recalculated. Headroom is directly related to
data_hard_start, data and data_meta, so we use them to get the new size.
The result is correct (similar pr_err() in page_to_skb, one case of
xdp_page and one case of virtnet buf):
a) Case with 4 bytes of metadata
[ 115.949641] page_to_skb: page addr ffff8b4dcfad2000 offset 252 headroom 252
[ 121.084105] page_to_skb: page addr ffff8b4dcf018000 offset 20732 headroom 252
b) Case of pushing data +32 bytes
[ 153.181401] page_to_skb: page addr ffff8b4dd0c4d000 offset 288 headroom 288
[ 158.480421] page_to_skb: page addr ffff8b4dd00b0000 offset 24864 headroom 288
c) Case of pushing data -33 bytes
[ 835.906830] page_to_skb: page addr ffff8b4dd3270000 offset 223 headroom 223
[ 840.839910] page_to_skb: page addr ffff8b4dcdd68000 offset 12511 headroom 223
Offset and headroom are equal because offset points to the start of
reserved bytes for the virtio_net header which are at buf start +
headroom, while data points at buf start + vnet hdr size + headroom so
when data or data_meta are adjusted by the xdp prog both the headroom size
and the offset change equally. We can use data_hard_start to compute the
new headroom after the xdp prog (linearized / page start case, the
virtnet buf case is similar just with bigger base offset):
xdp.data_hard_start = page_address + vnet_hdr
xdp.data = page_address + vnet_hdr + headroom
new headroom after xdp prog = xdp.data - xdp.data_hard_start - metasize
An example reproducer xdp prog[3] is below.
[1] https://github.com/cilium/cilium/issues/19453
[2] Two of the many traces:
[ 40.437400] BUG: Bad page state in process swapper/0 pfn:14940
[ 40.916726] BUG: Bad page state in process systemd-resolve pfn:053b7
[ 41.300891] kernel BUG at include/linux/mm.h:720!
[ 41.301801] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 41.302784] CPU: 1 PID: 1181 Comm: kubelet Kdump: loaded Tainted: G B W 5.18.0-rc1+ #37
[ 41.304458] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1.fc35 04/01/2014
[ 41.306018] RIP: 0010:page_frag_free+0x79/0xe0
[ 41.306836] Code: 00 00 75 ea 48 8b 07 a9 00 00 01 00 74 e0 48 8b 47 48 48 8d 50 ff a8 01 48 0f 45 fa eb d0 48 c7 c6 18 b8 30 a6 e8 d7 f8 fc ff <0f> 0b 48 8d 78 ff eb bc 48 8b 07 a9 00 00 01 00 74 3a 66 90 0f b6
[ 41.310235] RSP: 0018:ffffac05c2a6bc78 EFLAGS: 00010292
[ 41.311201] RAX: 000000000000003e RBX: 0000000000000000 RCX: 0000000000000000
[ 41.312502] RDX: 0000000000000001 RSI: ffffffffa6423004 RDI: 00000000ffffffff
[ 41.313794] RBP: ffff993c98823600 R08: 0000000000000000 R09: 00000000ffffdfff
[ 41.315089] R10: ffffac05c2a6ba68 R11: ffffffffa698ca28 R12: ffff993c98823600
[ 41.316398] R13: ffff993c86311ebc R14: 0000000000000000 R15: 000000000000005c
[ 41.317700] FS: 00007fe13fc56740(0000) GS:ffff993cdd900000(0000) knlGS:0000000000000000
[ 41.319150] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 41.320152] CR2: 000000c00008a000 CR3: 0000000014908000 CR4: 0000000000350ee0
[ 41.321387] Call Trace:
[ 41.321819] <TASK>
[ 41.322193] skb_release_data+0x13f/0x1c0
[ 41.322902] __kfree_skb+0x20/0x30
[ 41.343870] tcp_recvmsg_locked+0x671/0x880
[ 41.363764] tcp_recvmsg+0x5e/0x1c0
[ 41.384102] inet_recvmsg+0x42/0x100
[ 41.406783] ? sock_recvmsg+0x1d/0x70
[ 41.428201] sock_read_iter+0x84/0xd0
[ 41.445592] ? 0xffffffffa3000000
[ 41.462442] new_sync_read+0x148/0x160
[ 41.479314] ? 0xffffffffa3000000
[ 41.496937] vfs_read+0x138/0x190
[ 41.517198] ksys_read+0x87/0xc0
[ 41.535336] do_syscall_64+0x3b/0x90
[ 41.551637] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 41.568050] RIP: 0033:0x48765b
[ 41.583955] Code: e8 4a 35 fe ff eb 88 cc cc cc cc cc cc cc cc e8 fb 7a fe ff 48 8b 7c 24 10 48 8b 74 24 18 48 8b 54 24 20 48 8b 44 24 08 0f 05 <48> 3d 01 f0 ff ff 76 20 48 c7 44 24 28 ff ff ff ff 48 c7 44 24 30
[ 41.632818] RSP: 002b:000000c000a2f5b8 EFLAGS: 00000212 ORIG_RAX: 0000000000000000
[ 41.664588] RAX: ffffffffffffffda RBX: 000000c000062000 RCX: 000000000048765b
[ 41.681205] RDX: 0000000000005e54 RSI: 000000c000e66000 RDI: 0000000000000016
[ 41.697164] RBP: 000000c000a2f608 R08: 0000000000000001 R09: 00000000000001b4
[ 41.713034] R10: 00000000000000b6 R11: 0000000000000212 R12: 00000000000000e9
[ 41.728755] R13: 0000000000000001 R14: 000000c000a92000 R15: ffffffffffffffff
[ 41.744254] </TASK>
[ 41.758585] Modules linked in: br_netfilter bridge veth netconsole virtio_net
and
[ 33.524802] BUG: Bad page state in process systemd-network pfn:11e60
[ 33.528617] page ffffe05dc0147b00 ffffe05dc04e7a00 ffff8ae9851ec000 (1) len 82 offset 252 metasize 4 hroom 0 hdr_len 12 data ffff8ae9851ec10c data_meta ffff8ae9851ec108 data_end ffff8ae9851ec14e
[ 33.529764] page:000000003792b5ba refcount:0 mapcount:-512 mapping:0000000000000000 index:0x0 pfn:0x11e60
[ 33.532463] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
[ 33.532468] raw: 000fffffc0000000 0000000000000000 dead000000000122 0000000000000000
[ 33.532470] raw: 0000000000000000 0000000000000000 00000000fffffdff 0000000000000000
[ 33.532471] page dumped because: nonzero mapcount
[ 33.532472] Modules linked in: br_netfilter bridge veth netconsole virtio_net
[ 33.532479] CPU: 0 PID: 791 Comm: systemd-network Kdump: loaded Not tainted 5.18.0-rc1+ #37
[ 33.532482] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1.fc35 04/01/2014
[ 33.532484] Call Trace:
[ 33.532496] <TASK>
[ 33.532500] dump_stack_lvl+0x45/0x5a
[ 33.532506] bad_page.cold+0x63/0x94
[ 33.532510] free_pcp_prepare+0x290/0x420
[ 33.532515] free_unref_page+0x1b/0x100
[ 33.532518] skb_release_data+0x13f/0x1c0
[ 33.532524] kfree_skb_reason+0x3e/0xc0
[ 33.532527] ip6_mc_input+0x23c/0x2b0
[ 33.532531] ip6_sublist_rcv_finish+0x83/0x90
[ 33.532534] ip6_sublist_rcv+0x22b/0x2b0
[3] XDP program to reproduce(xdp_pass.c):
#include <linux/bpf.h>
#include <bpf/bpf_helpers.h>
SEC("xdp_pass")
int xdp_pkt_pass(struct xdp_md *ctx)
{
bpf_xdp_adjust_head(ctx, -(int)32);
return XDP_PASS;
}
char _license[] SEC("license") = "GPL";
compile: clang -O2 -g -Wall -target bpf -c xdp_pass.c -o xdp_pass.o
load on virtio_net: ip link set enp1s0 xdpdrv obj xdp_pass.o sec xdp_pass
CC: stable@vger.kernel.org
CC: Jason Wang <jasowang@redhat.com>
CC: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
CC: Daniel Borkmann <daniel@iogearbox.net>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: virtualization@lists.linux-foundation.org
Fixes: 8fb7da9e9907 ("virtio_net: get build_skb() buf by data ptr")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220425103703.3067292-1-razor@blackwall.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The other port_hidden functions rely on the port_read/port_write
functions to access the hidden control port. These functions apply the
offset for port_base_addr where applicable. Update port_hidden_wait to
use the port_wait_bit so that port_base_addr offsets are accounted for
when waiting for the busy bit to change.
Without the offset the port_hidden_wait function would timeout on
devices that have a non-zero port_base_addr (e.g. MV88E6141), however
devices that have a zero port_base_addr would operate correctly (e.g.
MV88E6390).
Fixes: 609070133aff ("net: dsa: mv88e6xxx: update code operating on hidden registers")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220425070454.348584-1-nathan@nathanrossi.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Return back the error value that we get from phy_read_mmd().
Fixes: c84786fa8f91 ("net: phy: marvell10g: read copper results from CSSR1")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/f47cb031aeae873bb008ba35001607304a171a20.1650868058.git.baruch@tkos.co.il
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'
However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.
Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.
As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com
Fixes: d03825fba459 ("net: bcmgenet: add skb_tx_timestamp call")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
plane_state->uapi.crtc is not what we want to be looking at.
If bigjoiner is used hw.crtc is what tells us what crtc the plane
is supposedly using.
Not an actual problem on current hardware as the only FBC capable
pipe (A) can't be a bigjoiner slave and thus uapi.crtc==hw.crtc
always here. But when we get more FBC instances this will become
actually important.
Fixes: 2e6c99f88679 ("drm/i915/fbc: Nuke lots of crap from intel_fbc_state_cache")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220413152852.7336-1-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
(cherry picked from commit 3e1faae3398789abe8d4797255bfe28d95d81308)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Fix typo in the _SEL_FETCH_PLANE_BASE_1_B register base address.
Fixes: a5523e2ff074a5 ("drm/i915: Add PSR2 selective fetch registers")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/5400
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v5.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421162221.2261895-1-imre.deak@intel.com
(cherry picked from commit af2cbc6ef967f61711a3c40fca5366ea0bc7fecc)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
It's noted that dcvs interrupts are not self-clearing, thus an interrupt
handler runs constantly, which leads to a severe regression in runtime.
To fix the problem an explicit write to clear interrupt register is
required, note that on OSM platforms the register may not be present.
Fixes: 275157b367f4 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
'size' may be used uninitialized in gsm_dlci_modem_output() if called with
an adaption that is neither 1 nor 2. The function is currently only called
by gsm_modem_upd_via_data() and only for adaption 2.
Properly handle every invalid case by returning -EINVAL to silence the
compiler warning and avoid future regressions.
Fixes: c19ffe00fed6 ("tty: n_gsm: fix invalid use of MSC in advanced option")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220425104726.7986-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clk fixes from Jernej Skrabec:
- Add missing sentinel
- check return value for platform_get_resource()
- mark rtc-32k as critical
* tag 'sunxi-clk-fixes-for-5.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()
clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical
clk: sunxi-ng: fix not NULL terminated coccicheck error
|
|
Since version 5.13, the standard syscon bindings have been added
to all clps711x DT nodes, so we can now use the more general
syscon_regmap_lookup_by_phandle function to get the syscon pointer.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Fixes: 7a6fca879f59 ("clk: sunxi: Add driver for A80 MMC config clocks/resets")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220421134308.2885094-1-yangyingliang@huawei.com
|
|
This code is really spurious.
It always returns an ERR_PTR, even when err is known to be 0 and calls
put_device() after a successful device_register() call.
It is likely that the return statement in the normal path is missing.
Add 'return rdev;' to fix it.
Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/ef2b9576350bba4c8e05e669e9535e9e2a415763.1650551719.git.christophe.jaillet@wanadoo.fr
|
|
Explicitly disable PEC when the client does not support it.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without a new code, at the second load of the driver
(or bind) the "flags" variable is not updated to avoid PEC usage. As a
consequence the further communication with the device is done with
the PEC enabled, which is wrong and may fail.
The implementation first disable the I2C_CLIENT_PEC flag, then the old
code enable it if needed.
Fixes: 4e5418f787ec ("hwmon: (pmbus_core) Check adapter PEC support")
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220420145059.431061-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This reverts 35a33ff3807d ("random: use memmove instead of memcpy for
remaining 32 bytes"), which was made on a totally bogus basis. The thing
it was worried about overlapping came from the stack, not from one of
its arguments, as Eric pointed out.
But the fact that this confusion even happened draws attention to the
fact that it's a bit non-obvious that the random_data parameter can
alias chacha_state, and in fact should do so when the caller can't rely
on the stack being cleared in a timely manner. So this commit documents
that.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
bridge
DSA, through dsa_port_bridge_leave(), first notifies the port of the
fact that it left a bridge, then, if that bridge was VLAN-aware, it
notifies the port of the change in VLAN awareness state, towards
VLAN-unaware mode.
So ocelot_port_vlan_filtering() can be called when ocelot_port->bridge
is NULL, and this makes ocelot_add_vlan_unaware_pvid() create a struct
ocelot_bridge_vlan with a vid of 0 and an "untagged" setting of true on
that port.
In a way this structure correctly reflects the reality, but by design,
VID 0 (OCELOT_STANDALONE_PVID) was not meant to be kept in the bridge
VLAN list of the driver, but managed separately.
Having OCELOT_STANDALONE_PVID in ocelot->vlans makes us trip up on
several sanity checks that did not expect to have this VID there.
For example, after we leave a VLAN-aware bridge and we re-join it, we
can no longer program egress-tagged VLANs to hardware:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 nomaster
# ip link set swp0 master br0
# bridge vlan add dev swp0 vid 100
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
But this configuration is in fact supported by the hardware, since we
could use OCELOT_PORT_TAG_NATIVE. According to its comment:
/* all VLANs except the native VLAN and VID 0 are egress-tagged */
yet when assessing the eligibility for this mode, we do not check for
VID 0 in ocelot_port_uses_native_vlan(), instead we just ensure that
ocelot_port_num_untagged_vlans() == 1. This is simply because VID 0
doesn't have a bridge VLAN structure.
The way I identify the problem is that ocelot_port_vlan_filtering(false)
only means to call ocelot_add_vlan_unaware_pvid() when we dynamically
turn off VLAN awareness for a bridge we are under, and the PVID changes
from the bridge PVID to a reserved PVID based on the bridge number.
Since OCELOT_STANDALONE_PVID is statically added to the VLAN table
during ocelot_vlan_init() and never removed afterwards, calling
ocelot_add_vlan_unaware_pvid() for it is not intended and does not serve
any purpose.
Fix the issue by avoiding the call to ocelot_add_vlan_unaware_pvid(vid=0)
when we're resetting VLAN awareness after leaving the bridge, to become
a standalone port.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both the felix DSA driver and ocelot switchdev driver declare
dev->features & NETIF_F_HW_VLAN_CTAG_FILTER under certain circumstances*,
so the 8021q module will add VID 0 to our RX filter when the port goes
up, to ensure 802.1p traffic is not dropped.
We treat VID 0 as a special value (OCELOT_STANDALONE_PVID) which
deliberately does not have a struct ocelot_bridge_vlan associated with
it. Instead, this gets programmed to the VLAN table in ocelot_vlan_init().
If we allow external calls to modify VID 0, we reach the following
situation:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 up # this adds VID 0 to ocelot->vlans with untagged=false
bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged # the bridge also adds VID 1
br0 1 PVID Egress Untagged
# bridge vlan add dev swp0 vid 100 untagged
Error: mscc_ocelot_switch_lib: Port with egress-tagged VLANs cannot have more than one egress-untagged (native) VLAN.
This configuration should have been accepted, because
ocelot_port_manage_port_tag() should select OCELOT_PORT_TAG_NATIVE.
Yet it isn't, because we have an entry in ocelot->vlans which says
VID 0 should be egress-tagged, something the hardware can't do.
Fix this by suppressing additions/deletions on VID 0 and managing this
VLAN exclusively using OCELOT_STANDALONE_PVID.
*DSA toggles it when the port becomes VLAN-aware by joining a VLAN-aware
bridge. Ocelot declares it unconditionally for some reason.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lan966x->ports[] array has lan966x->num_phys_ports elements. These
are assigned in lan966x_probe(). That means the > comparison should be
changed to >=.
The first off by one check is harmless but the second one could lead to
an out of bounds access and a crash.
Fixes: 5ccd66e01cbe ("net: lan966x: add support for interrupts from analyzer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
