| Age | Commit message (Collapse) | Author |
|---|
|
After using the built-in UEFI hardware diagnostics to compare
the measured battery temperature, i noticed that the temperature
is actually expressed in tenth degree kelvin, similar to the
SBS-Data standard. For example, a value of 2992 is displayed as
26 degrees celsius.
Fix the scaling so that the correct values are being displayed.
Tested on a Dell Inspiron 3505.
Fixes: a77272c16041 ("platform/x86: dell: Add new dell-wmi-ddv driver")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230218115318.20662-2-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
If one or both sensor buffers could not be initialized, either
due to missing hardware support or due to some error during probing,
the resume handler will encounter undefined behaviour when
attempting to lock buffers then protected by an uninitialized or
destroyed mutex.
Fix this by introducing a "active" flag which is set during probe,
and only invalidate buffers which where flaged as "active".
Tested on a Dell Inspiron 3505.
Fixes: 3b7eeff93d29 ("platform/x86: dell-ddv: Add hwmon support")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230218115318.20662-1-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
The amd_pmc_write_stb() function was previously hidden in an
ifdef to avoid a warning when CONFIG_SUSPEND is disabled, but
now there is an additional caller:
drivers/platform/x86/amd/pmc.c: In function 'amd_pmc_stb_debugfs_open_v2':
drivers/platform/x86/amd/pmc.c:256:8: error: implicit declaration of function 'amd_pmc_write_stb'; did you mean 'amd_pmc_read_stb'? [-Werror=implicit-function-declaration]
256 | ret = amd_pmc_write_stb(dev, AMD_PMC_STB_DUMMY_PC);
| ^~~~~~~~~~~~~~~~~
| amd_pmc_read_stb
There is now an easier way to handle this using DEFINE_SIMPLE_DEV_PM_OPS()
to replace all the #ifdefs, letting gcc drop any of the unused functions
silently.
Fixes: b0d4bb973539 ("platform/x86/amd: pmc: Write dummy postcode into the STB DRAM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230214152512.806188-1-arnd@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
Older platforms don't have qcom,vmid set, handle -EINVAL return value
correctly. And since num_vmids is passed to of_property_read_u32_array
later we should make sure it has a sane value before continuing.
Fixes: e656cd0bcf3d ("soc: qcom: rmtfs: Optionally map RMTFS to more VMs")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230305-rmtfs-vmid-fix-v1-2-6a7206081602@z3ntu.xyz
|
|
of_property_count_u32_elems returns a negative integer when an error
happens , but since the value was assigned to an unsigned integer, the
check never worked correctly. Also print the correct variable in the
error print, ret isn't used here.
Fixes: e656cd0bcf3d ("soc: qcom: rmtfs: Optionally map RMTFS to more VMs")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230305-rmtfs-vmid-fix-v1-1-6a7206081602@z3ntu.xyz
|
|
The slice IDs for CVPFW, CPUSS1 and CPUWHT currently overflow the 32bit
LLCC config registers, which means it is writing beyond the upper limit
of the ATTR0_CFGn and ATTR1_CFGn range of registers. But the most obvious
impact is the fact that the mentioned slices do not get configured at all,
which will result in reduced performance. Fix that by using the slice ID
values taken from the latest LLCC SC table.
Fixes: ec69dfbdc426 ("soc: qcom: llcc: Add sc8180x and sc8280xp configurations")
Cc: stable@vger.kernel.org # 5.19+
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Reviewed-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306135527.509796-1-abel.vesa@linaro.org
|
|
When the sd driver revalidates host-managed SMR disks, it calls
disk_set_zoned() which changes the zone_write_granularity attribute value
to the logical block size regardless of the device type. After that, the sd
driver overwrites the value in sd_zbc_read_zone() with the physical block
size, since ZBC/ZAC requires this for host-managed disks. Between the calls
to disk_set_zoned() and sd_zbc_read_zone(), there exists a window where the
attribute shows the logical block size as the zone_write_granularity value,
which is wrong for host-managed disks. The duration of the window is from
20ms to 200ms, depending on report zone command execution time.
To avoid the wrong zone_write_granularity value between disk_set_zoned()
and sd_zbc_read_zone(), modify the value not in sd_zbc_read_zone() but
just after disk_set_zoned() call.
Fixes: a805a4fa4fa3 ("block: introduce zone_write_granularity limit")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20230306063024.3376959-1-shinichiro.kawasaki@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Hyper-V uses a VHD or VHDX file on the host as the underlying storage for a
virtual disk. The VHD/VHDX file format is a sparse format where real disk
space on the host is assigned in chunks that the VHD/VHDX file format calls
the BlockSize. This BlockSize is not to be confused with the 512-byte (or
4096-byte) sector size of the underlying storage device. The default block
size for a new VHD/VHDX file is 32 Mbytes. When a guest VM touches any
disk space within a 32 Mbyte chunk of the VHD/VHDX file, Hyper-V allocates
32 Mbytes of real disk space for that section of the VHD/VHDX. Similarly,
if a discard operation is done that covers an entire 32 Mbyte chunk,
Hyper-V will free the real disk space for that portion of the VHD/VHDX.
This BlockSize is surfaced in Linux as the "discard_granularity" in
/sys/block/sd<x>/queue, which makes sense.
Hyper-V also has differencing disks that can overlay a VHD/VHDX file to
capture changes to the VHD/VHDX while preserving the original VHD/VHDX.
One example of this differencing functionality is for VM snapshots. When a
snapshot is created, a differencing disk is created. If the snapshot is
rolled back, Hyper-V can just delete the differencing disk, and the VM will
see the original disk contents at the time the snapshot was taken.
Differencing disks are used in other scenarios as well.
The BlockSize for a differencing disk defaults to 2 Mbytes, not 32 Mbytes.
The smaller default is used because changes to differencing disks are
typically scattered all over, and Hyper-V doesn't want to allocate 32
Mbytes of real disk space for a stray write here or there. The smaller
BlockSize provides more efficient use of real disk space.
When a differencing disk is added to a VHD/VHDX, Hyper-V reports
UNIT_ATTENTION with a sense code indicating "Operating parameters have
changed", because the value of discard_granularity should be changed to 2
Mbytes. When the differencing disk is removed, discard_granularity should
be changed back to 32 Mbytes. However, current code simply reports a
message from scsi_report_sense() and the value of
/sys/block/sd<x>/queue/discard_granularity is not updated. The message
isn't very actionable by a sysadmin.
Fix this by having the storvsc driver check for the sense code indicating
that the underly VHD/VHDX block size has changed, and do a rescan of the
device to pick up the new discard_granularity. With this change the entire
transition to/from differencing disks is handled automatically and
transparently, with no confusing messages being output.
Link: https://lore.kernel.org/r/1677516514-86060-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver version.
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20230302105342.34933-4-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In kdump kernel mode, the driver works in reduced functionality mode with
some features disabled such as reduced MSI-X count and RDPQ disabled, etc.
However, the firmware is not aware of this mode in some cases, which
results in undefined behavior.
To address this, the driver informs the firmware about the kdump mode
through MPI capabilities bit during driver initialization. This allows
firmware to adjust its behavior accordingly.
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20230302105342.34933-3-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The firmware only supports Logical Disk IDs up to 240 and LD ID 255 (0xFF)
is reserved for deleted LDs. However, in some cases, firmware was assigning
LD ID 254 (0xFE) to deleted LDs and this was causing the driver to mark the
wrong disk as deleted. This in turn caused the wrong disk device to be
taken offline by the SCSI midlayer.
To address this issue, limit the LD ID range from 255 to 240. This ensures
the deleted LD ID is properly identified and removed by the driver without
accidently deleting any valid LDs.
Fixes: ae6874ba4b43 ("scsi: megaraid_sas: Early detection of VD deletion through RaidMap update")
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20230302105342.34933-2-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the SAS Transport Layer support is enabled and a device exposed to
the OS by the driver fails INQUIRY commands, the driver frees up the memory
allocated for an internal HBA port data structure. However, in some places,
the reference to the freed memory is not cleared. When the firmware sends
the Device Info change event for the same device again, the freed memory is
accessed and that leads to memory corruption and OS crash.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-7-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A wrong variable is checked while populating PRP entries in the PRP page
and this results in failure. No PRP entries in the PRP page were
successfully created and any NVMe Encapsulated commands with PRP of size
greater than 8K failed.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-6-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Return proper non-zero return values for all the cases when the controller
initialization and re-initialization fails.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If a controller reset operation is triggered to recover the controller from
a fault state, then wait for the snapdump to be saved in the firmware
region before proceeding to reset the controller.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Prevent driver from trying to dereference a NULL pointer in a debug print
while removing a device during driver unload.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As part of Task Management handling, the driver will disable and enable the
MSIx index zero which belongs to the Admin reply queue. During this
transition the driver loses some interrupts and this leads to Admin request
and ioctl timeouts.
After enabling the interrupts, poll the Admin reply queue to avoid
timeouts.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Link: https://lore.kernel.org/r/20230228140835.4075-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the &epd_pool->list is empty when executing
lpfc_get_io_buf_from_expedite_pool() the function would return an invalid
pointer. Even in the case if the list is guaranteed to be populated, the
iterator variable should not be used after the loop to be more robust for
future changes.
Linus proposed to avoid any use of the list iterator variable after the
loop, in the attempt to move the list iterator variable declaration into
the macro to avoid any potential misuse after the loop [1].
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Signed-off-by: Jakob Koschel <jkl820.git@gmail.com>
Link: https://lore.kernel.org/r/20230301-scsi-lpfc-avoid-list-iterator-after-loop-v1-1-325578ae7561@gmail.com
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If kzalloc() fails in lpfc_sli4_cgn_params_read(), then we rely on
lpfc_read_object()'s routine to NULL check pdata.
Currently, an early return error is thrown from lpfc_read_object() to
protect us from NULL ptr dereference, but the errno code is -ENODEV.
Change the errno code to a more appropriate -ENOMEM.
Reported-by: Kang Chen <void0red@gmail.com>
Link: https://lore.kernel.org/all/20230226102338.3362585-1-void0red@gmail.com
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230228044336.5195-1-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Smatch static checker reported:
drivers/ufs/host/ufs-qcom.c:1469
ufs_qcom_mcq_config_resource() info: returning a literal zero is
cleaner
Fix the above warning by returning in place instead of a jump to a label.
Also remove the usage of devm_kfree() as it's unnecessary in this function.
Fixes: c263b4ef737e ("scsi: ufs: core: mcq: Configure resource regions")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Link: https://lore.kernel.org/r/3ebd2582af74b81ef7b57149f57c6a3bf0963953.1677721229.git.quic_asutoshd@quicinc.com
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix an error case in ufs_qcom_mcq_config_resource(), where the return value
is set to 0 before passing it to PTR_ERR.
This led to Smatch warning:
drivers/ufs/host/ufs-qcom.c:1455 ufs_qcom_mcq_config_resource() warn:
passing zero to 'PTR_ERR'
Fixes: c263b4ef737e ("scsi: ufs: core: mcq: Configure resource regions")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Link: https://lore.kernel.org/r/94ca99b327af634799ce5f25d0112c28cd00970d.1677721072.git.quic_asutoshd@quicinc.com
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The "dev_req_params" pointer points to inside the middle of a struct so it
can't be NULL. Removing this impossible condition is nice because now we
don't need to consider the correct error code for that situation.
Link: https://lore.kernel.org/r/Y/yA3niWUcGYgBU8@kili
Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The ufshcd driver uses simpleondemand governor for devfreq. Add it to the
list of ufshcd softdeps to allow userspace initramfs tools like dracut to
automatically pull the governor module into the initramfs together with UFS
drivers.
Link: https://lore.kernel.org/r/20230220140740.14379-1-athierry@redhat.com
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In case devm_add_action() fails, check it in the caller of
interrupt_preinit_v3_hw().
Link: https://lore.kernel.org/r/20230227031030.893324-1-void0red@gmail.com
Signed-off-by: Kang Chen <void0red@gmail.com>
Acked-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The K210 clock driver depends on SOC_CANAAN, which is only selectable
when !MMU on RISC-V. !MMU is not possible on 32-bit yet, but patches
have been sent for its enabling. The kernel test robot reported this
implicit 64-bit division there.
Replace the implicit division with an explicit one.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-riscv/202301201538.zNlqgE4L-lkp@intel.com/
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Link: https://lore.kernel.org/r/20230301002657.352637-2-Mr.Bossman075@gmail.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Commit 44c57f205876 ("scsi: qla2xxx: Changes to support FCP2 Target") added
support for FC2 Targets. Unfortunately, there are older setups which break
with this new feature enabled.
Allow to disable it via module option.
Link: https://lore.kernel.org/r/20230208152014.109214-1-dwagner@suse.de
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The first half of the error message is printed by pr_err(), the second half
is printed by pr_debug(). The user will therefore see only the first part
of the message and will miss some useful information.
Link: https://lore.kernel.org/r/20230214141556.762047-1-mlombard@redhat.com
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The loop in dmcrypt_write may be running for unbounded amount of time,
thus we need cond_resched() in it.
This commit fixes the following warning:
[ 3391.153255][ C12] watchdog: BUG: soft lockup - CPU#12 stuck for 23s! [dmcrypt_write/2:2897]
...
[ 3391.387210][ C12] Call trace:
[ 3391.390338][ C12] blk_attempt_bio_merge.part.6+0x38/0x158
[ 3391.395970][ C12] blk_attempt_plug_merge+0xc0/0x1b0
[ 3391.401085][ C12] blk_mq_submit_bio+0x398/0x550
[ 3391.405856][ C12] submit_bio_noacct+0x308/0x380
[ 3391.410630][ C12] dmcrypt_write+0x1e4/0x208 [dm_crypt]
[ 3391.416005][ C12] kthread+0x130/0x138
[ 3391.419911][ C12] ret_from_fork+0x10/0x18
Reported-by: yangerkun <yangerkun@huawei.com>
Fixes: dc2676210c42 ("dm crypt: offload writes to thread")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
This is an already known issue that dm-thin volume cannot be used as
swap, otherwise a deadlock may happen when dm-thin internal memory
demand triggers swap I/O on the dm-thin volume itself.
But thanks to commit a666e5c05e7c ("dm: fix deadlock when swapping to
encrypted device"), the limit_swap_bios target flag can also be used
for dm-thin to avoid the recursive I/O when it is used as swap.
Fix is to simply set ti->limit_swap_bios to true in both pool_ctr()
and thin_ctr().
In my test, I create a dm-thin volume /dev/vg/swap and use it as swap
device. Then I run fio on another dm-thin volume /dev/vg/main and use
large --blocksize to trigger swap I/O onto /dev/vg/swap.
The following fio command line is used in my test,
fio --name recursive-swap-io --lockmem 1 --iodepth 128 \
--ioengine libaio --filename /dev/vg/main --rw randrw \
--blocksize 1M --numjobs 32 --time_based --runtime=12h
Without this fix, the whole system can be locked up within 15 seconds.
With this fix, there is no any deadlock or hung task observed after
2 hours of running fio.
Furthermore, if blocksize is changed from 1M to 128M, after around 30
seconds fio has no visible I/O, and the out-of-memory killer message
shows up in kernel message. After around 20 minutes all fio processes
are killed and the whole system is back to being alive.
This is exactly what is expected when recursive I/O happens on dm-thin
volume when it is used as swap.
Depends-on: a666e5c05e7c ("dm: fix deadlock when swapping to encrypted device")
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Fix data corruption issue with SerDes connected PHYs operating at 1.25
Gbps speed where we could previously observe about 30% packet loss while
the bad packet counter was increasing.
As almost all boards with MediaTek MT7622 or MT7986 use either the MT7531
switch IC operating at 3.125Gbps SerDes rate or single-port PHYs using
rate-adaptation to 2500Base-X mode, this issue only got exposed now when
we started trying to use SFP modules operating with 1.25 Gbps with the
BananaPi R3 board.
The fix is to set bit 12 which disables the RX FIFO clear function when
setting up MAC MCR, MediaTek SDK did the same change stating:
"If without this patch, kernel might receive invalid packets that are
corrupted by GMAC."[1]
[1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/d8a2975939a12686c4a95c40db21efdc3f821f63
Fixes: 42c03844e93d ("net-next: mediatek: add support for MediaTek MT7622 SoC")
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/138da2735f92c8b6f8578ec2e5a794ee515b665f.1677937317.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently link up can't be detected in forced mode if polling
isn't used. Only link up interrupt source we have is aneg
complete which isn't applicable in forced mode. Therefore we
have to use energy-on as link up indicator.
Fixes: 7365494550f6 ("net: phy: smsc: skip ENERGYON interrupt if disabled")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to what seems to be a copy-paste error, the _NRT master was
identical to the _RT master, which should not be the case.. Fix it
using the values available from the downstream kernel [1].
[1] https://android.googlesource.com/kernel/msm-extra/devicetree/+/refs/heads/android-msm-bramble-4.19-android11-qpr1/qcom/scuba-bus.dtsi#127
Fixes: 1a14b1ac3935 ("interconnect: qcom: Add QCM2290 driver support")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20230103142120.15605-1-konrad.dybcio@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
It turns out that commit 596ff4a09b89 ("cpumask: re-introduce
constant-sized cpumask optimizations") exposed a number of cases of
drivers not checking the result of "cpumask_next()" and friends
correctly.
The documented correct check for "no more cpus in the cpumask" is to
check for the result being equal or larger than the number of possible
CPU ids, exactly _because_ we've always done those constant-sized
cpumask scans using a widened type before. So the return value of a
cpumask scan should be checked with
if (cpu >= nr_cpu_ids)
...
because the cpumask scan did not necessarily stop exactly *at* that
maximum CPU id.
But a few cases ended up instead using checks like
if (cpu == nr_cpumask_bits)
...
which used that internal "widened" number of bits. And that used to
work pretty much by accident (ok, in this case "by accident" is simply
because it matched the historical internal implementation of the cpumask
scanning, so it was more of a "intentionally using implementation
details rather than an accident").
But the extended constant-sized optimizations then did that internal
implementation differently, and now that code that did things wrong but
matched the old implementation no longer worked at all.
Which then causes subsequent odd problems due to using what ends up
being an invalid CPU ID.
Most of these cases require either unusual hardware or special uses to
hit, but the random.c one triggers quite easily.
All you really need is to have a sufficiently small CONFIG_NR_CPUS value
for the bit scanning optimization to be triggered, but not enough CPUs
to then actually fill that widened cpumask. At that point, the cpumask
scanning will return the NR_CPUS constant, which is _not_ the same as
nr_cpumask_bits.
This just does the mindless fix with
sed -i 's/== nr_cpumask_bits/>= nr_cpu_ids/'
to fix the incorrect uses.
The ones in the SCSI lpfc driver in particular could probably be fixed
more cleanly by just removing that repeated pattern entirely, but I am
not emptionally invested enough in that driver to care.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/lkml/481b19b5-83a0-4793-b4fd-194ad7b978c3@roeck-us.net/
Reported-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/lkml/CAMuHMdUKo_Sf7TjKzcNDa8Ve+6QrK+P8nSQrSQ=6LTRmcBKNww@mail.gmail.com/
Reported-by: Vernon Yang <vernon2gm@gmail.com>
Link: https://lore.kernel.org/lkml/20230306160651.2016767-1-vernon2gm@gmail.com/
Cc: Yury Norov <yury.norov@gmail.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
A fix for nouveau preventing the system shutdown and one for a build
warning, and NULL pointer dereference fix for cirrus.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230223083839.5gtmu6i42bnj7pfh@houat
|
|
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 3a49afb84ca0 ("clk: enable hi655x common clk automatically")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Riku Voipio <riku.voipio@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-3-rdunlap@infradead.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Link: https://lore.kernel.org/r/20230222121453.91915-13-nick.alcock@oracle.com
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20230222121453.91915-12-nick.alcock@oracle.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Change sm8550 interconnect driver to use generic qcom_icc_rpmh_*
functions rather than embedding a copy of thema. This also fixes an
overallocation of memory for icc_onecell_data structure.
Fixes: e6f0d6a30f73 ("interconnect: qcom: Add SM8550 interconnect provider driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230105002221.1416479-4-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Change sm8450 interconnect driver to use generic qcom_icc_rpmh_*
functions rather than embedding a copy of thema. This also fixes an
overallocation of memory for icc_onecell_data structure.
Fixes: fafc114a468e ("interconnect: qcom: Add SM8450 interconnect provider driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230105002221.1416479-3-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
This is a struct with a trailing zero-length array of icc_node pointers
but it's allocated as if it were a single array of icc_nodes instead.
Fortunately this overallocates memory rather then allocating less memory
than required.
Fix by replacing devm_kcalloc() with devm_kzalloc() and struct_size()
macro.
Fixes: 5bc9900addaf ("interconnect: qcom: Add OSM L3 interconnect provider support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230105002221.1416479-2-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Add QUIRK_NO_CLX to disable the CLx state for hardware which
doesn't supports it.
AMD Yellow Carp and Pink Sardine don't support CLx state,
hence disabling it using QUIRK_NO_CLX.
Cc: stable@vger.kernel.org
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
[mw: added debug log when the quirk is run]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Following warning reported by KASAN during driver unload
==================================================================
BUG: KASAN: double-free in bnxt_remove_one+0x103/0x200 [bnxt_en]
Free of addr ffff88814e8dd4c0 by task rmmod/17469
CPU: 47 PID: 17469 Comm: rmmod Kdump: loaded Tainted: G S 6.2.0-rc7+ #2
Hardware name: Dell Inc. PowerEdge R740/01YM03, BIOS 2.3.10 08/15/2019
Call Trace:
<TASK>
dump_stack_lvl+0x33/0x46
print_report+0x17b/0x4b3
? __call_rcu_common.constprop.79+0x27e/0x8c0
? __pfx_free_object_rcu+0x10/0x10
? __virt_addr_valid+0xe3/0x160
? bnxt_remove_one+0x103/0x200 [bnxt_en]
kasan_report_invalid_free+0x64/0xd0
? bnxt_remove_one+0x103/0x200 [bnxt_en]
? bnxt_remove_one+0x103/0x200 [bnxt_en]
__kasan_slab_free+0x179/0x1c0
? bnxt_remove_one+0x103/0x200 [bnxt_en]
__kmem_cache_free+0x194/0x350
bnxt_remove_one+0x103/0x200 [bnxt_en]
pci_device_remove+0x62/0x110
device_release_driver_internal+0xf6/0x1c0
driver_detach+0x76/0xe0
bus_remove_driver+0x89/0x160
pci_unregister_driver+0x26/0x110
? strncpy_from_user+0x188/0x1c0
bnxt_exit+0xc/0x24 [bnxt_en]
__x64_sys_delete_module+0x21f/0x390
? __pfx___x64_sys_delete_module+0x10/0x10
? __pfx_mem_cgroup_handle_over_high+0x10/0x10
? _raw_spin_lock+0x87/0xe0
? __pfx__raw_spin_lock+0x10/0x10
? __audit_syscall_entry+0x185/0x210
? ktime_get_coarse_real_ts64+0x51/0x80
? syscall_trace_enter.isra.18+0x126/0x1a0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7effcb6fd71b
Code: 73 01 c3 48 8b 0d 6d 17 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 17 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffeada270b8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 00005623660e0750 RCX: 00007effcb6fd71b
RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005623660e07b8
RBP: 0000000000000000 R08: 00007ffeada26031 R09: 0000000000000000
R10: 00007effcb771280 R11: 0000000000000206 R12: 00007ffeada272e0
R13: 00007ffeada28bc4 R14: 00005623660e02a0 R15: 00005623660e0750
</TASK>
Auxiliary device structures are freed in bnxt_aux_dev_release. So avoid
calling kfree from bnxt_remove_one.
Also, set bp->edev to NULL before freeing the auxilary private structure.
Fixes: d80d88b0dfff ("bnxt_en: Add auxiliary driver support")
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to keep track of all the possible concurrent TPA (GRO/LRO)
completions on the aggregation ring. On P5 chips, the maximum number
of concurrent TPA is 256 and the amount of memory we allocate is order-5
on systems using 4K pages. Memory allocation failure has been reported:
NetworkManager: page allocation failure: order:5, mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 15 PID: 2995 Comm: NetworkManager Kdump: loaded Not tainted 5.10.156 #1
Hardware name: Dell Inc. PowerEdge R660/0M1CC5, BIOS 0.2.25 08/12/2022
Call Trace:
dump_stack+0x57/0x6e
warn_alloc.cold.120+0x7b/0xdd
? _cond_resched+0x15/0x30
? __alloc_pages_direct_compact+0x15f/0x170
__alloc_pages_slowpath.constprop.108+0xc58/0xc70
__alloc_pages_nodemask+0x2d0/0x300
kmalloc_order+0x24/0xe0
kmalloc_order_trace+0x19/0x80
bnxt_alloc_mem+0x1150/0x15c0 [bnxt_en]
? bnxt_get_func_stat_ctxs+0x13/0x60 [bnxt_en]
__bnxt_open_nic+0x12e/0x780 [bnxt_en]
bnxt_open+0x10b/0x240 [bnxt_en]
__dev_open+0xe9/0x180
__dev_change_flags+0x1af/0x220
dev_change_flags+0x21/0x60
do_setlink+0x35c/0x1100
Instead of allocating this big chunk of memory and dividing it up for the
concurrent TPA instances, allocate each small chunk separately for each
TPA instance. This will reduce it to order-0 allocations.
Fixes: 79632e9ba386 ("bnxt_en: Expand bnxt_tpa_info struct to support 57500 chips.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The locking in phy_probe() and phy_remove() does very little to prevent
any races with e.g. phy_attach_direct(), but instead causes lockdep ABBA
warnings. Remove it.
======================================================
WARNING: possible circular locking dependency detected
6.2.0-dirty #1108 Tainted: G W E
------------------------------------------------------
ip/415 is trying to acquire lock:
ffff5c268f81ef50 (&dev->lock){+.+.}-{3:3}, at: phy_attach_direct+0x17c/0x3a0 [libphy]
but task is already holding lock:
ffffaef6496cb518 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x154/0x560
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.}-{3:3}:
__lock_acquire+0x35c/0x6c0
lock_acquire.part.0+0xcc/0x220
lock_acquire+0x68/0x84
__mutex_lock+0x8c/0x414
mutex_lock_nested+0x34/0x40
rtnl_lock+0x24/0x30
sfp_bus_add_upstream+0x34/0x150
phy_sfp_probe+0x4c/0x94 [libphy]
mv3310_probe+0x148/0x184 [marvell10g]
phy_probe+0x8c/0x200 [libphy]
call_driver_probe+0xbc/0x15c
really_probe+0xc0/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__device_attach_driver+0xc4/0x160
bus_for_each_drv+0x80/0xe0
__device_attach+0xb0/0x1f0
device_initial_probe+0x1c/0x2c
bus_probe_device+0xa4/0xb0
device_add+0x360/0x53c
phy_device_register+0x60/0xa4 [libphy]
fwnode_mdiobus_phy_device_register+0xc0/0x190 [fwnode_mdio]
fwnode_mdiobus_register_phy+0x160/0xd80 [fwnode_mdio]
of_mdiobus_register+0x140/0x340 [of_mdio]
orion_mdio_probe+0x298/0x3c0 [mvmdio]
platform_probe+0x70/0xe0
call_driver_probe+0x34/0x15c
really_probe+0xc0/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__driver_attach+0x104/0x210
bus_for_each_dev+0x78/0xdc
driver_attach+0x2c/0x3c
bus_add_driver+0x184/0x240
driver_register+0x80/0x13c
__platform_driver_register+0x30/0x3c
xt_compat_calc_jump+0x28/0xa4 [x_tables]
do_one_initcall+0x50/0x1b0
do_init_module+0x50/0x1fc
load_module+0x684/0x744
__do_sys_finit_module+0xc4/0x140
__arm64_sys_finit_module+0x28/0x34
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0x6c/0x1b0
do_el0_svc+0x34/0x44
el0_svc+0x48/0xf0
el0t_64_sync_handler+0xb8/0xc0
el0t_64_sync+0x1a0/0x1a4
-> #0 (&dev->lock){+.+.}-{3:3}:
check_prev_add+0xb4/0xc80
validate_chain+0x414/0x47c
__lock_acquire+0x35c/0x6c0
lock_acquire.part.0+0xcc/0x220
lock_acquire+0x68/0x84
__mutex_lock+0x8c/0x414
mutex_lock_nested+0x34/0x40
phy_attach_direct+0x17c/0x3a0 [libphy]
phylink_fwnode_phy_connect.part.0+0x70/0xe4 [phylink]
phylink_fwnode_phy_connect+0x48/0x60 [phylink]
mvpp2_open+0xec/0x2e0 [mvpp2]
__dev_open+0x104/0x214
__dev_change_flags+0x1d4/0x254
dev_change_flags+0x2c/0x7c
do_setlink+0x254/0xa50
__rtnl_newlink+0x430/0x514
rtnl_newlink+0x58/0x8c
rtnetlink_rcv_msg+0x17c/0x560
netlink_rcv_skb+0x64/0x150
rtnetlink_rcv+0x20/0x30
netlink_unicast+0x1d4/0x2b4
netlink_sendmsg+0x1a4/0x400
____sys_sendmsg+0x228/0x290
___sys_sendmsg+0x88/0xec
__sys_sendmsg+0x70/0xd0
__arm64_sys_sendmsg+0x2c/0x40
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0x6c/0x1b0
do_el0_svc+0x34/0x44
el0_svc+0x48/0xf0
el0t_64_sync_handler+0xb8/0xc0
el0t_64_sync+0x1a0/0x1a4
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(rtnl_mutex);
lock(&dev->lock);
lock(rtnl_mutex);
lock(&dev->lock);
*** DEADLOCK ***
Fixes: 298e54fa810e ("net: phy: add core phylib sfp support")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When SCMI raw coexistence mode is enabled make the core stack probe
successfully even when the initial base protocol exchanges with the
platform/server failed.
This behaviour enables the system to boot with a broken regular SCMI
stack but with a fully functional and accessible SCMI raw debugfs
interface that can be used to further debug the issue.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20230223152330.2707260-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
linux/of.h is included more than once, just remove the duplicate include
header inclusion.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202302101520071730986@zte.com.cn
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
In this context "return scmi_dev;" and "return NULL;" are equivalent
but it is more readable to return a literal.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/Y/Yx8pOdf8rNhPVe@kili
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The comments say "enabled" where "disabled" is intended. Also it's
cleaner to return zero explicitly instead of ret.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y86im5M49p3ePGxj@kili
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Playing media with a resolution smaller than the crtc size requires the
video overlay to be scaled for output and GXM boards display a 1px pink
line on the bottom of the scaled overlay. Comparing with the downstream
vendor driver revealed VPP_DUMMY_DATA not being set [0].
Setting VPP_DUMMY_DATA prevents the 1px pink line from being seen.
[0] https://github.com/endlessm/linux-s905x/blob/master/drivers/amlogic/amports/video.c#L7869
Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller")
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230303123312.155164-1-christianshewitt@gmail.com
|
|
When MAC is not support PMT, driver will check PHY's WoL capability
and set device wakeup capability in stmmac_init_phy(). We can enable
the WoL through ethtool, the driver would enable the device wake up
flag. Now the device_may_wakeup() return true.
But if there is a way which enable the PHY's WoL capability derectly,
like in BIOS. The driver would not know the enable thing and would not
set the device wake up flag. The phy_suspend may failed like this:
[ 32.409063] PM: dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x50 returns -16
[ 32.409065] PM: Device stmmac-1:00 failed to suspend: error -16
[ 32.409067] PM: Some devices failed to suspend, or early wake event detected
Add to set the device wakeup enable flag according to the get_wol
function result in PHY can fix the error in this scene.
v2: add a Fixes tag.
Fixes: 1d8e5b0f3f2c ("net: stmmac: Support WOL with phy")
Signed-off-by: Rongguang Wei <weirongguang@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
