| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Just several fixups,
- fix page fault and vblank timeout issues due to delayed vblank handling.
- fix panel driver probing to fail without te-gpios property.
- fix potential security hole by using "%pK" format.
- fix wrong if statement condition.
And one cleanup which removes Exynos4415 SoC support which is not supported
anymore.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos/dsi: make te-gpios optional
drm/exynos: Print kernel pointers in a restricted form
drm/exynos/decon5433: fix software trigger mask
drm/exynos/fimd: signal frame done interrupt at front porch
drm/exynos/decon5433: signal frame done interrupt at front porch
drm/exynos/decon5433: fix vblank event handling
drm/exynos: move crtc event handling to drivers callbacks
drm/exynos: Remove support for Exynos4415 (SoC not supported anymore)
drm/exynos/decon5433: & vs | typo
|
|
We can build modular code that uses mdiobus_register_board_info() which would
lead to linking failure since this symbol is not expoerted.
Fixes: 648ea0134069 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* pm-cpuidle-fixes:
cpuidle: Validate cpu_dev in cpuidle_add_sysfs()
|
|
'intel_pstate-fixes'
* pm-cpufreq-fixes:
cpufreq: Restore policy min/max limits on CPU online
* pm-cpufreq-sched-fixes:
cpufreq: schedutil: Fix per-CPU structure initialization in sugov_start()
* intel_pstate-fixes:
cpufreq: intel_pstate: Fix policy data management in passive mode
cpufreq: intel_pstate: One set of global limits in active mode
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-fixes
Pull Allwinner clock fixes from Maxime Ripard:
A few fixes for a bunch of clocks on a few SoCs. The most important one is
probably one that fixes the NKMP clock frequency calculation and could end
up with clocking the CPU frequency to out of bounds rates.
* tag 'sunxi-clk-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: fix recalc_rate formula of NKMP clocks
clk: sunxi-ng: Fix div/mult settings for osc12M on A64
clk: sunxi-ng: sun6i: Fix enable bit offset for hdmi-ddc module clock
clk: sunxi: ccu-sun5i needs nkmp
clk: sunxi-ng: mp: Adjust parent rate for pre-dividers
|
|
controller
During early days of PCI quirks support, ThunderX firmware did not provide
PNP0c02 node with PCI configuration space and PEM-specific register ranges.
This means that for legacy FW we are not reserving these resources and
cannot gather PEM-specific resources for further PEM initialization.
To support already deployed legacy FW, calculate PEM-specific ranges and
provide resources reservation as fallback scenario into PEM driver when we
could not gather PEM reg base from ACPI tables.
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
|
|
"CAV" is the only PNP/ACPI hardware ID vendor prefix assigned to Cavium so
fix this as it should be from day one.
Fixes: 44f22bd91e88 ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller")
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
|
|
In ACPI world any ID should be carefully chosen and registered
officially. The commit bbf9d262a147 seems did a wrong assumption because
PCA is the registered PNP ID for "PHILIPS BU ADD ON CARD". I'm pretty
sure this prefix has nothing to do with the driver in question.
Moreover, newer ACPI specification has a support of _DSD method and
special device IDs to allow drivers be enumerated via compatible string.
The slight change to support this kind of enumeration will be added in
sequential patch against pca954x.c.
Revert the commit bbf9d262a147 for good.
Cc: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.11-rc4
Some more device ids for option and qcserial.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.11-rc4
f_acm got an endianness fix by Oliver Neukum. This has been around for a
long time but it's finally fixed.
f_hid learned that it should never access hidg->req without first
grabbing the spinlock.
Roger Quadros fixed two bugs in the f_uvc function driver.
Janusz Dziedzic fixed a very peculiar bug with EP0, one that's rather
difficult to trigger. When we're dealing with bounced EP0 requests, we
should delay unmap until after ->complete() is called.
UDC class got a use-after-free fix.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.11-rc
*) Revert USB3 PHY support for Broadcom NSP SoC
*) Fix compiler error on qcom-usb-hs when depends on EXTCON
is not added
*) Fix error handling in phy-exynos-pcie
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The latest gcc-7 snapshot adds a warning to point out that when
atk_read_value_old or atk_read_value_new fails, we copy
uninitialized data into sensor->cached_value:
drivers/hwmon/asus_atk0110.c: In function 'atk_input_show':
drivers/hwmon/asus_atk0110.c:651:26: error: 'value' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Adding an error check avoids this. All versions of the driver
are affected.
Fixes: 2c03d07ad54d ("hwmon: Add Asus ATK0110 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull networking fixes from David Miller:
1) Several netfilter fixes from Pablo and the crew:
- Handle fragmented packets properly in netfilter conntrack, from
Florian Westphal.
- Fix SCTP ICMP packet handling, from Ying Xue.
- Fix big-endian bug in nftables, from Liping Zhang.
- Fix alignment of fake conntrack entry, from Steven Rostedt.
2) Fix feature flags setting in fjes driver, from Taku Izumi.
3) Openvswitch ipv6 tunnel source address not set properly, from Or
Gerlitz.
4) Fix jumbo MTU handling in amd-xgbe driver, from Thomas Lendacky.
5) sk->sk_frag.page not released properly in some cases, from Eric
Dumazet.
6) Fix RTNL deadlocks in nl80211, from Johannes Berg.
7) Fix erroneous RTNL lockdep splat in crypto, from Herbert Xu.
8) Cure improper inflight handling during AF_UNIX GC, from Andrey
Ulanov.
9) sch_dsmark doesn't write to packet headers properly, from Eric
Dumazet.
10) Fix SCM_TIMESTAMPING_OPT_STATS handling in TCP, from Soheil Hassas
Yeganeh.
11) Add some IDs for Motorola qmi_wwan chips, from Tony Lindgren.
12) Fix nametbl deadlock in tipc, from Ying Xue.
13) GRO and LRO packets not counted correctly in mlx5 driver, from Gal
Pressman.
14) Fix reset of internal PHYs in bcmgenet, from Doug Berger.
15) Fix hashmap allocation handling, from Alexei Starovoitov.
16) nl_fib_input() needs stronger netlink message length checking, from
Eric Dumazet.
17) Fix double-free of sk->sk_filter during sock clone, from Daniel
Borkmann.
18) Fix RX checksum offloading in aquantia driver, from Pavel Belous.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
net:ethernet:aquantia: Fix for RX checksum offload.
amd-xgbe: Fix the ECC-related bit position definitions
sfc: cleanup a condition in efx_udp_tunnel_del()
Bluetooth: btqcomsmd: fix compile-test dependency
inet: frag: release spinlock before calling icmp_send()
tcp: initialize icsk_ack.lrcvtime at session start time
genetlink: fix counting regression on ctrl_dumpfamily()
socket, bpf: fix sk_filter use after free in sk_clone_lock
ipv4: provide stronger user input validation in nl_fib_input()
bpf: fix hashmap extra_elems logic
enic: update enic maintainers
net: bcmgenet: remove bcmgenet_internal_phy_setup()
ipv6: make sure to initialize sockc.tsflags before first use
fjes: Do not load fjes driver if extended socket device is not power on.
fjes: Do not load fjes driver if system does not have extended socket device.
net/mlx5e: Count LRO packets correctly
net/mlx5e: Count GSO packets correctly
net/mlx5: Increase number of max QPs in default profile
net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps
net/mlx5e: Use the proper UAPI values when offloading TC vlan actions
...
|
|
This was broken in commit cd979883b9ed ("xen/acpi-processor:
fix enabling interrupts on syscore_resume"). do_suspend (from
xen/manage.c) and thus xen_resume_notifier never get called on
the initial-domain at resume (it is if running as guest.)
The rationale for the breaking change was that upload_pm_data()
potentially does blocking work in syscore_resume(). This patch
addresses the original issue by scheduling upload_pm_data() to
execute in workqueue context.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@vger.kernel.org
Based-on-patch-by: Konrad Wilk <konrad.wilk@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
On a randconfig build without CONFIG_SCSI_LPFC_DEBUG_FS, I ran into
multiple compile failures:
drivers/scsi/lpfc/lpfc_debugfs.h: In function 'lpfc_debug_dump_wq':
drivers/scsi/lpfc/lpfc_debugfs.h:405:15: error: 'DUMP_FCP' undeclared (first use in this function); did you mean 'DUMP_VAR'?
drivers/scsi/lpfc/lpfc_debugfs.h:405:15: note: each undeclared identifier is reported only once for each function it appears in
drivers/scsi/lpfc/lpfc_debugfs.h:408:22: error: 'DUMP_NVME' undeclared (first use in this function); did you mean 'DUMP_NONE'?
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_ls_rsp_cmp':
drivers/scsi/lpfc/lpfc_nvmet.c:109:2: error: implicit declaration of function 'lpfc_nvmeio_data'; did you mean 'lpfc_mem_free'? [-Werror=implicit-function-declaration]
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_fcp_op':
drivers/scsi/lpfc/lpfc_nvmet.c:523:10: error: unused variable 'id' [-Werror=unused-variable]
They are all trivial to fix, so I'm doing it in a combined patch here.
Fixes: 1d9d5a9879ad ("scsi: lpfc: refactor debugfs queue dump routines")
Fixes: bd2cdd5e400f ("scsi: lpfc: NVME Initiator: Add debugfs support")
Fixes: 2b65e18202fd ("scsi: lpfc: NVME Target: Add debugfs support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
lpfc cannot establish connection with targets that send PRLI in P2P
configurations.
If lpfc rejects a PRLI that is sent from a target the target will not
resend and will reject the PRLI send from the initiator.
[mkp: applied by hand]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In a previous patch a hpsa_scsi_dev_t.volume_offline update line has
been removed, so let us put it back..
Fixes: 85b29008d8 (hpsa: update check for logical volume status)
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Otherwise this can also prevent modesets e.g. for switching VTs, when
multiple monitors with different native resolutions are connected.
The depths must match though, so keep the != test for that.
Also update the DRM_DEBUG output to be slightly more accurate, this
doesn't only affect requests from userspace.
Bugzilla: https://bugs.freedesktop.org/99841
Fixes: 865afb11949e ("drm/fb-helper: reject any changes to the fbdev")
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323085326.20185-1-michel@daenzer.net
|
|
Replace hard coded "ACPI0007" with ACPI_PROCESSOR_DEVICE_HID
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Provide debugfs function stubs when EDAC_DEBUG is not enabled so that we
don't fail the build:
drivers/edac/pnd2_edac.c: In function ‘pnd2_init’:
drivers/edac/pnd2_edac.c:1521:2: error: implicit declaration of function ‘setup_pnd2_debug’ [-Werror=implicit-function-declaration]
setup_pnd2_debug();
^
drivers/edac/pnd2_edac.c: In function ‘pnd2_exit’:
drivers/edac/pnd2_edac.c:1529:2: error: implicit declaration of function ‘teardown_pnd2_debug’ [-Werror=implicit-function-declaration]
teardown_pnd2_debug();
^
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
The debugfs.c functionality relies on DEBUG_FS so select it.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
This patch adds the missing PINGROUP for GPIO70-99.
This fixes a crash that happens in pinctrl-msm, if any
of the GPIO70-99 are accessed.
Fixes: 5303f7827fcd41d ("pinctrl: qcom: ipq4019: set ngpios to correct value")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When using GPIO as IRQ source, the GPIO must be configured
in INPUT. Callbacks dedicated for this was missing in
pinctrl-st driver.
This fix the following kernel error when trying to lock a gpio
as IRQ:
[ 7.521095] gpio gpiochip7: (PIO11): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 7.526018] gpio gpiochip7: (PIO11): unable to lock HW IRQ 6 for IRQ
[ 7.529405] genirq: Failed to request resources for 0-0053 (irq 81) on irqchip GPIO
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Clearing the status bit on irq_unmask will discard any pending interrupt
that did arrive after the irq_ack, i.e. while the IRQ handler function
was executing.
Fixes: f365be092572 ("pinctrl: Add Qualcomm TLMM driver")
Cc: stable@vger.kernel.org
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some pinctrls share memory regions, and devm_ioremap_resource does not
allow to share resources, in opposition to devm_ioremap.
This patch restores back usage of devm_ioremap function, but with proper
error handling and logging.
Fixes: baafaca ("pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()")
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As the IODelay driver is a hardware feature of the DRA7xxx SoC
depend on that SoC and compile test.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this
via NETIF_F_RXCSUM flag.
v1->v2: 'Signed-off-by' tag added.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Presumably if there is an "add" function, there is also a "del"
function. But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
compile-testing fails when QCOM_SMD is a loadable module:
drivers/bluetooth/built-in.o: In function `btqcomsmd_send':
btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send'
drivers/bluetooth/built-in.o: In function `btqcomsmd_probe':
btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel'
btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata'
This clarifies the dependency to allow compile-testing only when
SMD is completely disabled, otherwise the dependency on QCOM_SMD
will make sure we can link against it.
Fixes: e27ee2b16bad ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for v4.11-rc4
* tag 'drm-intel-fixes-2017-03-22' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: make context status notifier head be per engine
drm/i915: Avoid rcu_barrier() from reclaim paths (shrinker)
drm/i915/gvt: Fix gvt scheduler interval time
drm/i915/gvt: GVT pin/unpin shadow context
drm/i915/gvt: scan shadow indirect context image when valid
drm/i915/kvmgt: fix suspicious rcu dereference usage
drm/i915/gvt: add enable_execlists check before enable gvt
drm/i915/gvt: Remove bogus retry around i915_wait_request
drm/i915/gvt: correct the ggtt valid bit check in pipe control command
drm/i915/gvt: replace the gvt_err with gvt_vgpu_err
drm/i915/gvt: handle force-nonpriv registers, cmd parser part
drm/i915: Do .init_clock_gating() earlier to avoid it clobbering watermarks
drm/i915/glk: Remove MODULE_FIRMWARE() tag from Geminilake's DMC
drm/i915: Reject HDMI 12bpc if the sink doesn't indicate support
drm/i915: Always call i915_gem_reset_finish() following i915_gem_reset_prepare()
drm/i915: Stop using RP_DOWN_EI on Baytrail
drm/i915: Drop support for I915_EXEC_CONSTANTS_* execbuf parameters.
drm/i915: Only enable hotplug interrupts if the display interrupts are enabled
drm/i915: Disable engine->irq_tasklet around resets
drm/i915: Split GEM resetting into 3 phases
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into iommu/fixes
|
|
Commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a6108b ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a6a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The extended device socket cannot turn on/off while system is running.
So when system boots up and the device is not power on, the fjes driver
does not need be loaded.
To check the status of the device, the patch adds ACPI _STA method check.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fjes driver is used only by FUJITSU servers and almost of all
servers in the world never use it. But currently if ACPI PNP0C02
is defined in the ACPI table, the following message is always shown:
"FUJITSU Extended Socket Network Device Driver - version 1.2
- Copyright (c) 2015 FUJITSU LIMITED"
The message makes users confused because there is no reason that
the message is shown in other vendor servers.
To avoid the confusion, the patch adds a check that the server
has a extended socket device or not.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb202 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we use the non UAPI values and we miss erring on
the modify action which is not supported, fix that.
Fixes: 8b32580df1cb ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa916588e ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
E-Switch
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa916588e ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23d1 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e478f ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':
As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.
Fixes: 6246168b4a38 ("net: ethernet: ti: netcp: add support of cpts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
revert commit a59e6d815226 ("r8152: correct the rx early size") and
fix the rx early size as
(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
