| Age | Commit message (Collapse) | Author |
|---|
|
Robert reported the following when booting a CXL host with Restricted CXL
Host (RCH) topology:
[ 39.815379] cxl_acpi ACPI0017:00: not a cxl_port device
[ 39.827123] WARNING: CPU: 46 PID: 1754 at drivers/cxl/core/port.c:592 to_cxl_port+0x56/0x70 [cxl_core]
... plus some related subsequent NULL pointer dereference:
[ 40.718708] BUG: kernel NULL pointer dereference, address: 00000000000002d8
The iterator to walk the PCIe path did not account for RCH topology.
However RCH does not support hotplug and the memory exported by the
Restricted CXL Device (RCD) should be covered by HMAT and therefore no
access_coordinate is needed. Add check to see if the endpoint device is
RCD and skip calculation.
Also add a call to cxl_endpoint_get_perf_coordinates() in cxl_test in order
to exercise the topology iterator. The dev_is_pci() check added is to help
with this test and should be harmless for normal operation.
Reported-by: Robert Richter <rrichter@amd.com>
Closes: https://lore.kernel.org/all/Ziv8GfSMSbvlBB0h@rric.localdomain/
Fixes: 592780b8391f ("cxl: Fix retrieving of access_coordinates in PCIe path")
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Robert Richter <rrichter@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Link: https://lore.kernel.org/r/20240426224913.1027420-1-dave.jiang@intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
|
priv.runtime_map is only allocated when efi_novamap is not set.
Otherwise, it is an uninitialized value. In the error path, it is freed
unconditionally. Avoid passing an uninitialized value to free_pool.
Free priv.runtime_map only when it was allocated.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: f80d26043af9 ("efi: libstub: avoid efi_get_memory_map() for allocating the virt map")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Some new SOF changes depend on the fixes there.
|
|
The via-macii ADB driver calls request_irq() after disabling hard
interrupts. But disabling interrupts isn't necessary here because the
VIA shift register interrupt was masked during VIA1 initialization.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/419fcc09d0e563b425c419053d02236b044d86b0.1710298421.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
We can use the DEFINE_RES_MEM_NAMED() macro and resource_contains()
helper instead of reimplementing them in the code. No functional change
intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230831121623.36293-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Uses NEC defaults as other non-eeprom devices.
Link: https://lore.kernel.org/linux-media/2273969.FyfRTN5kjP@bootes
Signed-off-by: Alex Volkov <alex@bootes.sytes.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The macro parameter name, sd, captures the field name in the third
argument of container_of. Fortunately, the argument at all uses is
actually sd. But change the macro parameter name anyway, for a little
added safety.
Link: https://lore.kernel.org/linux-media/20230315090904.20092-1-Julia.Lawall@inria.fr
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Some camera sensor can output the embedded data in specific data type.
This patch adds the support for metadata capture in IPU6 ISYS driver.
Signed-off-by: Hongju Wang <hongju.wang@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Co-developed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add Kconfig and Makefile for the IPU6 driver.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Andreas Helbech Kleist <andreaskleist@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The main input system driver does basic ISYS hardware setup, IRQ handling
and sets up device nodes.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Register V4L2 video device and setup the VB2 queues to support video
capture. Video streaming callback will trigger the input system driver to
construct a input system stream configuration for firmware based on data
type and stream ID and then queue buffers to firmware to do capture.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Co-developed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
IPU6 CSI-2 D-PHY hardware varies on different platforms, current IPU6 has
three D-PHY hardware instances which are used on Tigerlake, Alder lake,
Meteor lake and Jasper lake. MCD D-PHY is included in Tigerlake and Alder
lake, DWC D-PHY is included in Meteor lake.
Each PHY has its own register interface, the input system driver calls the
appropriate D-PHY callbacks for the hardware set in isys_probe().
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Input system CSI2 receiver is exposed as a v4l2 sub-device. Each CSI2
sub-device represent one single CSI2 hardware port which be linked with
external sub-device such camera sensor by linked with ISYS CSI2's sink
pad. The CSI2 source pad is linked to the sink pad of video capture device.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Implement the input system firmware ABIs in the ISYS driver, including
stream configuration, control command, capture request and response.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Co-developed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Syscom is an inter-process(or) communication mechanism between an IPU and
host. Syscom uses message queues for message exchange between IPU and
host. Each message queue has its consumer and producer, host queue
messages to firmware as the producer and then firmware to dequeue the
messages as consumer and vice versa. IPU and host use shared registers or
memory to reside the read and write indices which are updated by consumer
and producer.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The Intel IPU6 has internal microcontrollers (scalar processor, SP) which
are used to execute the firmware. The SPs can access IPU internal memory
and system DRAM mapped to its an internal 32-bit virtual address space.
This patch adds a driver for the IPU MMU and a DMA mapping implementation
using the internal MMU. The system IOMMU may be used besides the IPU MMU.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
For IPU6, firmware is generated and released as signed Code Partition
Directory (CPD) format file which is aligned with the SPI flash code
partition definition. The CPD format includes CPD header, manifest,
metadata and module data. The driver parses them according to the CPD
layout to acquire each component.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The IPU6 buttress is the interface between IPU device (input system and
processing system) with rest of the SoC. It contains overall IPU hardware
control registers, these control registers are used as the interfaces with
the Intel Converged Security Engine and Punit to do firmware
authentication and power management.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Even though the IPU input system and processing system are in a single PCI
device, each system has its own power sequence. Powering up the processing
system depends on first powering up the input system.
Besides, both the input and processing systems have their own MMU hardware
for IPU DMA address mapping.
Register the IS/PS devices on auxiliary bus and attach power domain to
implement the power sequence dependency.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Intel Image Processing Unit 6th Gen includes input and processing systems
but the hardware presents itself as a single PCI device in system.
The IPU6 PCI device driver basically does PCI configurations and loads the
firmware binary, initialises IPU virtual bus and sets up platform specific
variants to support multiple IPU6 devices in single device driver.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Use IPU bridge to instantiate software nodes for IPU6 related devices. If
the IPU6 device is probed before the MEI CSI device is created, neither
will probe unless there are further devices probed successfully which
triggers re-probe of both IPU6 and MEI CSI.
This patch ensures the necessary software nodes are in place when the MEI
CSI driver is probed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add a driver for the Unicam camera receiver block on BCM283x processors.
It is represented as two video device nodes: unicam-image and
unicam-embedded which are connected to an internal subdev (named
unicam-subdev) in order to manage streams routing.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Co-developed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Co-developed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Sakari Ailus: Squash fixes by Laurent.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
This is a packed grey-scale image format with a depth of 14 bits per
pixel. Every four consecutive samples are packed into seven bytes. Each
of the first four bytes contain the eight high order bits of the pixels,
and the three following bytes contains the six least significants bits
of each pixel, in the same order.
As the other formats only needed 5 bytes before, append two bytes in the
documentation array.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
This is a packed grey-scale image format with a depth of 12 bits per
pixel. Two consecutive pixels are packed into 3 bytes. The first 2 bytes
contain the 8 high order bits of the pixels, and the 3rd byte contains
the 4 least significants bits of each pixel, in the same order.
Add the entry in userspace API, and document it.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add trivial S_ROUTING IOCTL support for drivers where routing is static.
Essentially this means returning the same information G_ROUTING call would
have done.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Julien Massot <julien.massot@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Return the routes set using S_ROUTING back to the user. Also reflect this
in documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The len_routes field is used to tell the size of the routes array in
struct v4l2_subdev_routing. This way the number of routes returned from
S_ROUTING IOCTL may be larger than the number of routes provided, in case
there are more routes returned by the driver.
Note that this uAPI is still disabled in the code, so this change can
safely be done. Anyone who manually patched the code to enable this uAPI
must update their code.
The patch also increases the number of reserved fields in struct
v4l2_subdev_routing.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
As the user needs to know what went wrong for S_ROUTING, copy array
arguments back to the user.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add two new functions, v4l2_subdev_lock_states() and
v4l2_subdev_unclock_states(), to acquire and release the state of two
sub-devices. They differ from calling v4l2_subdev_{un,}lock_state() so
that if the two states share the same lock, the lock is acquired only
once.
Also use the new functions in v4l2_subdev_link_validate().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Set (and unset) the V4L2_FMT_FLAG_META_LINE_BASED flag in struct
v4l2_fmtdesc based on the format after returning the driver callback for
enumerating formats. This way the drivers don't need to care about the
flag.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Many camera sensors, among other devices, transmit embedded data and image
data for each CSI-2 frame. This embedded data typically contains register
configuration of the sensor that has been used to capture the image data
of the same frame.
The embedded data is received by the CSI-2 receiver and has the same
properties as the image data, including that it is line based: it has
width, height and bytesperline (stride).
Add these fields to struct v4l2_meta_format and document them.
Also add V4L2_FMT_FLAG_META_LINE_BASED to tell a given format is
line-based i.e. these fields of struct v4l2_meta_format are valid for it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Generic 8-bit metadata formats define the in-memory data layout but not
the format of the data itself. The reasoning for having such formats is to
allow CSI-2 receiver drivers to receive and DMA drivers to write the data
to memory without knowing a large number of device-specific formats.
These formats may be used only in conjunction with a Media Controller
pipeline where the internal pad of the source sub-device defines the
specific format of the data (using an mbus code).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
VXLAN stores per-VNI statistics using vxlan_vnifilter_count().
These statistics were not updated when arp_reduce() failed its
pskb_may_pull() call.
Use vxlan_vnifilter_count() to update the VNI counter when that
happens.
Fixes: 4095e0e1328a ("drivers: vxlan: vnifilter: per vni stats")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VXLAN devices update their stats locklessly. Therefore these counters
should either be stored in per-cpu data structures or the updates
should be done using atomic increments.
Since the net_device_core_stats infrastructure is already used in
vxlan_rcv(), use it for the other rx_dropped and tx_dropped counter
updates. Update the other counters atomically using DEV_STATS_INC().
Fixes: d342894c5d2f ("vxlan: virtual extensible lan")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the PTP programmable gpios to implement also PTP_PF_EXTTS
function. The pins can be configured to capture both of rising
and falling edge. Once the event is seen, then an interrupt is
generated and the LTC is saved in the registers.
On lan8814 only GPIO 3 can be configured for this.
This was tested using:
ts2phc -m -l 7 -s generic -f ts2phc.cfg
Where the configuration was the following:
---
[global]
ts2phc.pin_index 3
[eth0]
---
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit introduces LED drivers for rtl8366rb, enabling LEDs to be
described in the device tree using the same format as qca8k. Each port
can configure up to 4 LEDs.
If all LEDs in a group use the default state "keep", they will use the
default behavior after a reset. Changing the brightness of one LED,
either manually or by a trigger, will disable the default hardware
trigger and switch the entire LED group to manually controlled LEDs.
Once in this mode, there is no way to revert to hardware-controlled LEDs
(except by resetting the switch).
Software triggers function as expected with manually controlled LEDs.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The necessity of asserting the reset on removal was previously
questioned, as DSA's own cleanup methods should suffice to prevent
traffic leakage[1].
When a driver has subdrivers controlled by devres, they will be
unregistered after the main driver's .remove is executed. If it asserts
a reset, the subdrivers will be unable to communicate with the hardware
during their cleanup. For LEDs, this means that they will fail to turn
off, resulting in a timeout error.
[1] https://lore.kernel.org/r/20240123215606.26716-9-luizluca@gmail.com/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch family supports four LEDs for each of its six ports. Each
LED group is composed of one of these four LEDs from all six ports. LED
groups can be configured to display hardware information, such as link
activity, or manually controlled through a bitmap in registers
RTL8366RB_LED_0_1_CTRL_REG and RTL8366RB_LED_2_3_CTRL_REG.
After a reset, the default LED group configuration for groups 0 to 3
indicates, respectively, link activity, link at 1000M, 100M, and 10M, or
RTL8366RB_LED_CTRL_REG as 0x5432. These configurations are commonly used
for LED indications. However, the driver was replacing that
configuration to use manually controlled LEDs (RTL8366RB_LED_FORCE)
without providing a way for the OS to control them. The default
configuration is deemed more useful than fixed, uncontrollable turned-on
LEDs.
The driver was enabling/disabling LEDs during port_enable/disable.
However, these events occur when the port is administratively controlled
(up or down) and are not related to link presence. Additionally, when a
port N was disabled, the driver was turning off all LEDs for group N,
not only the corresponding LED for port N in any of those 4 groups. In
such cases, if port 0 was brought down, the LEDs for all ports in LED
group 0 would be turned off. As another side effect, the driver was
wrongly warning that port 5 didn't have an LED ("no LED for port 5").
Since showing the administrative state of ports is not an orthodox way
to use LEDs, it was not worth it to fix it and all this code was
dropped.
The code to disable LEDs was simplified only changing each LED group to
the RTL8366RB_LED_OFF state. Registers RTL8366RB_LED_0_1_CTRL_REG and
RTL8366RB_LED_2_3_CTRL_REG are only used when the corresponding LED
group is configured with RTL8366RB_LED_FORCE and they don't need to be
cleaned. The code still references an LED controlled by
RTL8366RB_INTERRUPT_CONTROL_REG, but as of now, no test device has
actually used it. Also, some magic numbers were replaced by macros.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of (struct rt6_info *)dst casts, we can use :
#define dst_rt6_info(_ptr) \
container_of_const(_ptr, struct rt6_info, dst)
Some places needed missing const qualifiers :
ip6_confirm_neigh(), ipv6_anycast_destination(),
ipv6_unicast_destination(), has_gateway()
v2: added missing parts (David Ahern)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the host page size was more than 4 times larger than the FW page
size, this macro evaluated to zero resulting in zero-sized arrays.
Use DIV_ROUND_UP() to ensure the correct behavior.
Reported-by: 20240228012313.5934-1-yaolu@kylinos.cn
Closes: https://lore.kernel.org/dri-devel/20240228012313.5934-1-yaolu@kylinos.cn
Link: https://lore.kernel.org/dri-devel/20240228012313.5934-1-yaolu@kylinos.cn
Fixes: 927f3e0253c1 ("drm/imagination: Implement MIPS firmware processor and MMU support")
Cc: stable@vger.kernel.org
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
|
|
release_firmware() checks for NULL pointers internally so checking
before calling it is redundant.
Link: https://lore.kernel.org/linux-media/20220606014433.290667-1-chi.minghao@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add Grand Ridge (ATOM_CRESTMONT) to hpm_cpu_ids, so that MSR 0x54 can be
used.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240422212222.3881606-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Commit d725d20e81c2 ("media: flexcop-usb: sanity checking of endpoint type
") adds a sanity check for endpoint[1], but fails to modify the sanity
check of bNumEndpoints.
Fix this by modifying the sanity check of bNumEndpoints to 2.
Link: https://lore.kernel.org/linux-media/20220602055027.849014-1-dzm91@hust.edu.cn
Fixes: d725d20e81c2 ("media: flexcop-usb: sanity checking of endpoint type")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
High speed is no longer the ultimate in speed.
Link: https://lore.kernel.org/linux-media/20220517131109.28371-2-oneukum@suse.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
No need for GFP_ATOMIC during probe()
Link: https://lore.kernel.org/linux-media/20220517131109.28371-1-oneukum@suse.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
No need for GFP_ATOMIC during probe()
Link: https://lore.kernel.org/linux-media/20220517111049.25611-1-oneukum@suse.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The driver should disable regulators when fails to probe.
Link: https://lore.kernel.org/linux-media/20220510114852.1719018-1-zheyuma97@gmail.com
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The driver should check whether the client provides the platform_data.
The following log reveals it:
[ 29.610324] BUG: KASAN: null-ptr-deref in kmemdup+0x30/0x40
[ 29.610730] Read of size 40 at addr 0000000000000000 by task bash/414
[ 29.612820] Call Trace:
[ 29.613030] <TASK>
[ 29.613201] dump_stack_lvl+0x56/0x6f
[ 29.613496] ? kmemdup+0x30/0x40
[ 29.613754] print_report.cold+0x494/0x6b7
[ 29.614082] ? kmemdup+0x30/0x40
[ 29.614340] kasan_report+0x8a/0x190
[ 29.614628] ? kmemdup+0x30/0x40
[ 29.614888] kasan_check_range+0x14d/0x1d0
[ 29.615213] memcpy+0x20/0x60
[ 29.615454] kmemdup+0x30/0x40
[ 29.615700] lgdt3306a_probe+0x52/0x310
[ 29.616339] i2c_device_probe+0x951/0xa90
Link: https://lore.kernel.org/linux-media/20220405095018.3993578-1-zheyuma97@gmail.com
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Spectrum ASICs only support a single interrupt, that means that all the
events are handled by one IRQ (interrupt request) handler. Once an
interrupt is received, we schedule tasklet to handle events from EQ and
then schedule tasklets to handle completions from CQs. Tasklet runs in
softIRQ (software IRQ) context, and will be run on the same CPU which
scheduled it. That means that today we use only one CPU to handle all the
packets (both network packets and EMADs) from hardware.
This can be improved using NAPI. The idea is to use NAPI instance per
CQ, which is mapped 1:1 to DQ (RDQ or SDQ). NAPI poll method can be run
in kernel thread, so then the driver will be able to handle WQEs in several
CPUs. Convert the existing code to use NAPI APIs.
Add NAPI instance as part of 'struct mlxsw_pci_queue' and initialize it
as part of CQs initialization. Set the appropriate poll method and dummy
net device, according to queue number, similar to tasklet setup. For CQs
which are used for completions of RDQ, use Rx poll method and
'napi_dev_rx', which is set as 'threaded'. It means that Rx poll method
will run in kernel context, so several RDQs will be handled in parallel.
For CQs which are used for completions of SDQ, use Tx poll method and
'napi_dev_tx', this method will run in softIRQ context, as it is
recommended in NAPI documentation, as Tx packets' processing is short task.
Convert mlxsw_pci_cq_{rx,tx}_tasklet() to poll methods. Handle 'budget'
argument - ignore it in Tx poll method, as it is recommended to not limit
Tx processing. For Rx processing, handle up to 'budget' completions.
Return 'work_done' which is the amount of completions that were handled.
Handle the following cases:
1. After processing 'budget' completions, the driver still has work to do:
Return work-done = budget. In that case, the NAPI instance will be
polled again (without the need to be rescheduled). Do not re-arm the
queue, as NAPI will handle the reschedule, so we do not have to involve
hardware to send an additional interrupt for the completions that should
be processed.
2. Event processing has been completed:
Call napi_complete_done() to mark NAPI processing as completed, which
means that the poll method will not be rescheduled. Re-arm the queue,
as all completions were handled.
In case that poll method handled exactly 'budget' completions, return
work-done = budget -1, to distinguish from the case that driver still
has completions to handle. Otherwise, return the amount of completions
that were handled.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch will set the driver to use NAPI for event processing. Then
tasklet mechanism will be used only for EQ. Reorganize 'mlxsw_pci_queue'
to hold EQ and CQ attributes in a union. For now, add tasklet for both EQ
and CQ. This will be changed in the next patch, as 'tasklet_struct' will be
replaced with NAPI instance.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
