| Age | Commit message (Collapse) | Author |
|---|
|
Tolerance applies on both sides of the target voltage, i.e. both min and
max sides. But while checking if a voltage is supported by the regulator
or not, we haven't taken care of tolerance on the lower side. Fix that.
Cc: Lucas Stach <l.stach@pengutronix.de>
Fixes: 045ee45c4ff2 ("cpufreq: cpufreq-dt: disable unsupported OPPs")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We need to explicitly mark OPPs as shared, when they are not defined
with OPP-v2 bindings. This operation can potentially fail, and in that
case we should at least print an error message.
Fixes: 2e02d8723edf ("cpufreq: dt: Add support for operating-points-v2 bindings")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We need to explicitly mark OPPs as shared, when they are not defined
with OPP-v2 bindings. But this isn't required to be done if we failed to
initialize OPP table.
Reorder code to verify OPP count before marking them shared.
Fixes: 2e02d8723edf ("cpufreq: dt: Add support for operating-points-v2 bindings")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper update from Mike Snitzer:
- a couple small cleanups in dm-cache, dm-verity, persistent-data's
dm-btree, and DM core.
- a 4.1-stable fix for dm-cache that fixes the leaking of deferred bio
prison cells
- a 4.2-stable fix that adds feature reporting for the dm-stats
features added in 4.2
- improve DM-snapshot to not invalidate the on-disk snapshot if
snapshot device write overflow occurs; but a write overflow triggered
through the origin device will still invalidate the snapshot.
- optimize DM-thinp's async discard submission a bit now that late bio
splitting has been included in block core.
- switch DM-cache's SMQ policy lock from using a mutex to a spinlock;
improves performance on very low latency devices (eg. NVMe SSD).
- document DM RAID 4/5/6's discard support
[ I did not pull the slab changes, which weren't appropriate for this
tree, and weren't obviously the right thing to do anyway. At the very
least they need some discussion and explanation before getting merged.
Because not pulling the actual tagged commit but doing a partial pull
instead, this merge commit thus also obviously is missing the git
signature from the original tag ]
* tag 'dm-4.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix use after freeing migrations
dm cache: small cleanups related to deferred prison cell cleanup
dm cache: fix leaking of deferred bio prison cells
dm raid: document RAID 4/5/6 discard support
dm stats: report precise_timestamps and histogram in @stats_list output
dm thin: optimize async discard submission
dm snapshot: don't invalidate on-disk image on snapshot write overflow
dm: remove unlikely() before IS_ERR()
dm: do not override error code returned from dm_get_device()
dm: test return value for DM_MAPIO_SUBMITTED
dm verity: remove unused mempool
dm cache: move wake_waker() from free_migrations() to where it is needed
dm btree remove: remove unused function get_nr_entries()
dm btree: remove unused "dm_block_t root" parameter in btree_split_sibling()
dm cache policy smq: change the mutex to a spinlock
|
|
Commit 06bb6f5a69df ("mtd: spi-nor: stop (ab)using struct
spi_device_id") converted an array into a pointer, which means that
we should be checking if the pointer goes anywhere, not whether the C
string is empty. To do the latter means we dereference a NULL pointer
when we reach the terminating entry, for which 'name' is now NULL
instead of an array { 0, 0, ... }.
Sample crash:
[ 1.101371] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 1.109457] pgd = c0004000
[ 1.112157] [00000000] *pgd=00000000
[ 1.115736] Internal error: Oops: 5 [#1] SMP ARM
[ 1.120345] Modules linked in:
[ 1.123405] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 4.2.0-next-20150902+ #61
[ 1.130611] Hardware name: Rockchip (Device Tree)
[ 1.135306] task: ee0b8d40 ti: ee0ba000 task.ti: ee0ba000
[ 1.140697] PC is at spi_nor_scan+0x90/0x8c4
[ 1.144958] LR is at spi_nor_scan+0xa4/0x8c4
...
[ 1.504112] [<c03cc2e0>] (spi_nor_scan) from [<c03cb188>] (m25p_probe+0xc8/0x11c)
[ 1.511583] [<c03cb188>] (m25p_probe) from [<c03cd9d8>] (spi_drv_probe+0x60/0x7c)
[ 1.519055] [<c03cd9d8>] (spi_drv_probe) from [<c037faa0>] (driver_probe_device+0x1a0/0x444)
[ 1.527478] [<c037faa0>] (driver_probe_device) from [<c037fec8>] (__device_attach_driver+0x94/0xa0)
[ 1.536507] [<c037fec8>] (__device_attach_driver) from [<c037db3c>] (bus_for_each_drv+0x94/0xa4)
[ 1.545277] [<c037db3c>] (bus_for_each_drv) from [<c037f7e4>] (__device_attach+0xa4/0x144)
[ 1.553526] [<c037f7e4>] (__device_attach) from [<c0380058>] (device_initial_probe+0x1c/0x20)
[ 1.562035] [<c0380058>] (device_initial_probe) from [<c037ec88>] (bus_probe_device+0x38/0x94)
[ 1.570631] [<c037ec88>] (bus_probe_device) from [<c037ccf4>] (device_add+0x430/0x558)
[ 1.578534] [<c037ccf4>] (device_add) from [<c03d0240>] (spi_add_device+0xe4/0x174)
[ 1.586178] [<c03d0240>] (spi_add_device) from [<c03d0a24>] (spi_register_master+0x698/0x7d4)
[ 1.594688] [<c03d0a24>] (spi_register_master) from [<c03d0ba0>] (devm_spi_register_master+0x40/0x7c)
[ 1.603892] [<c03d0ba0>] (devm_spi_register_master) from [<c03d2fb4>] (rockchip_spi_probe+0x360/0x3f4)
[ 1.613182] [<c03d2fb4>] (rockchip_spi_probe) from [<c0381e34>] (platform_drv_probe+0x58/0xa8)
[ 1.621779] [<c0381e34>] (platform_drv_probe) from [<c037faa0>] (driver_probe_device+0x1a0/0x444)
[ 1.630635] [<c037faa0>] (driver_probe_device) from [<c037fdc4>] (__driver_attach+0x80/0xa4)
[ 1.639058] [<c037fdc4>] (__driver_attach) from [<c037e850>] (bus_for_each_dev+0x98/0xac)
[ 1.647221] [<c037e850>] (bus_for_each_dev) from [<c037f448>] (driver_attach+0x28/0x30)
[ 1.655210] [<c037f448>] (driver_attach) from [<c037ef74>] (bus_add_driver+0x128/0x250)
[ 1.663200] [<c037ef74>] (bus_add_driver) from [<c0380c40>] (driver_register+0xac/0xf0)
[ 1.671191] [<c0380c40>] (driver_register) from [<c0381d50>] (__platform_driver_register+0x58/0x6c)
[ 1.680221] [<c0381d50>] (__platform_driver_register) from [<c0a467c8>] (rockchip_spi_driver_init+0x18/0x20)
[ 1.690033] [<c0a467c8>] (rockchip_spi_driver_init) from [<c00098a4>] (do_one_initcall+0x124/0x1dc)
[ 1.699063] [<c00098a4>] (do_one_initcall) from [<c0a19f84>] (kernel_init_freeable+0x218/0x2ec)
[ 1.707748] [<c0a19f84>] (kernel_init_freeable) from [<c0719ed8>] (kernel_init+0x1c/0xf4)
[ 1.715912] [<c0719ed8>] (kernel_init) from [<c000fe50>] (ret_from_fork+0x14/0x24)
[ 1.723460] Code: e3510000 159f67c0 0a00000c e5961000 (e5d13000)
[ 1.729564] ---[ end trace 95baa6b3b861ce25 ]---
Fixes: 06bb6f5a69df ("mtd: spi-nor: stop (ab)using struct spi_device_id")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
|
|
The patch just to re-submit the patch "db3421c114cfa6326" because the
patch "4d494cdc92b3b9a0" remove the change.
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This chip can be found on Hitex LPC4350 Evaluation Board.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
According to the datasheet[1], both S25FL129P0 (256kB sectors) and
S25FL129P1 (64kB sectors) support dual read, quad read, dual i/o read
and quad i/o read.
I have verified dual read to be working for S25FL129P1 on a dual
capable spi controller. Quad as well as S25FL129P0 is untested, lacking
hardware to verify.
[1] http://www.spansion.com/Support/Datasheets/S25FL129P_00.pdf
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
As both omap2 onenand and omap2 nand driver modules are
named the same i.e. "omap2.ko", only one of them gets shipped
during MODPOST if both are configured as loadable modules.
To avoid this ambiguity let's ship the omap2 nand
driver as "omap2_nand.ko"
Reported by Pierre Neyron via github
https://github.com/beagleboard/linux/issues/40
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
It is a 256KiB flash with 4 KiB erase sectors
and 64KiB overlay blocks.
This is the one available on Hardkernel's Odroid U3 shield.
Signed-off-by: Alexis Ballier <aballier@gentoo.org>
[Brian: seems like this does NOT require the usual SST_WRITE hacks]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Add Micron (n25q064a) 8MB flash to the list of supported chips.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
[Brian: fixup context]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Pull SG updates from Jens Axboe:
"This contains a set of scatter-gather related changes/fixes for 4.3:
- Add support for limited chaining of sg tables even for
architectures that do not set ARCH_HAS_SG_CHAIN. From Christoph.
- Add sg chain support to target_rd. From Christoph.
- Fixup open coded sg->page_link in crypto/omap-sham. From
Christoph.
- Fixup open coded crypto ->page_link manipulation. From Dan.
- Also from Dan, automated fixup of manual sg_unmark_end()
manipulations.
- Also from Dan, automated fixup of open coded sg_phys()
implementations.
- From Robert Jarzmik, addition of an sg table splitting helper that
drivers can use"
* 'for-4.3/sg' of git://git.kernel.dk/linux-block:
lib: scatterlist: add sg splitting function
scatterlist: use sg_phys()
crypto/omap-sham: remove an open coded access to ->page_link
scatterlist: remove open coded sg_unmark_end instances
crypto: replace scatterwalk_sg_chain with sg_chain
target/rd: always chain S/G list
scatterlist: allow limited chaining without ARCH_HAS_SG_CHAIN
|
|
Pull block driver updates from Jens Axboe:
"On top of the 4.3 core block IO changes, here are the driver related
changes for 4.3. Basically just NVMe and nbd this time around:
- NVMe:
- PRACT PI improvement from Alok Pandey.
- Cleanups and improvements on submission queue doorbell and
writing, using CMB if available. From Jon Derrick.
- From Keith, support for setting queue maximum segments, and
reset support.
- Also from Jon, fixup of u64 division issue on 32-bit archs and
wiring up of the reset support through and ioctl.
- Two small cleanups from Matias and Sunad
- Various code cleanups and fixes from Markus Pargmann"
* 'for-4.3/drivers' of git://git.kernel.dk/linux-block:
NVMe: Using PRACT bit to generate and verify PI by controller
NVMe:Remove unreachable code in nvme_abort_req
NVMe: Add nvme subsystem reset IOCTL
NVMe: Add nvme subsystem reset support
NVMe: removed unused nn var from nvme_dev_add
NVMe: Set queue max segments
nbd: flags is a u32 variable
nbd: Rename functions for clearness of recv/send path
nbd: Change 'disconnect' to be boolean
nbd: Add debugfs entries
nbd: Remove variable 'pid'
nbd: Move clear queue debug message
nbd: Remove 'harderror' and propagate error properly
nbd: restructure sock_shutdown
nbd: sock_shutdown, remove conditional lock
nbd: Fix timeout detection
nvme: Fixes u64 division which breaks i386 builds
NVMe: Use CMB for the IO SQes if available
NVMe: Unify SQ entry writing and doorbell ringing
|
|
Pull core block updates from Jens Axboe:
"This first core part of the block IO changes contains:
- Cleanup of the bio IO error signaling from Christoph. We used to
rely on the uptodate bit and passing around of an error, now we
store the error in the bio itself.
- Improvement of the above from myself, by shrinking the bio size
down again to fit in two cachelines on x86-64.
- Revert of the max_hw_sectors cap removal from a revision again,
from Jeff Moyer. This caused performance regressions in various
tests. Reinstate the limit, bump it to a more reasonable size
instead.
- Make /sys/block/<dev>/queue/discard_max_bytes writeable, by me.
Most devices have huge trim limits, which can cause nasty latencies
when deleting files. Enable the admin to configure the size down.
We will look into having a more sane default instead of UINT_MAX
sectors.
- Improvement of the SGP gaps logic from Keith Busch.
- Enable the block core to handle arbitrarily sized bios, which
enables a nice simplification of bio_add_page() (which is an IO hot
path). From Kent.
- Improvements to the partition io stats accounting, making it
faster. From Ming Lei.
- Also from Ming Lei, a basic fixup for overflow of the sysfs pending
file in blk-mq, as well as a fix for a blk-mq timeout race
condition.
- Ming Lin has been carrying Kents above mentioned patches forward
for a while, and testing them. Ming also did a few fixes around
that.
- Sasha Levin found and fixed a use-after-free problem introduced by
the bio->bi_error changes from Christoph.
- Small blk cgroup cleanup from Viresh Kumar"
* 'for-4.3/core' of git://git.kernel.dk/linux-block: (26 commits)
blk: Fix bio_io_vec index when checking bvec gaps
block: Replace SG_GAPS with new queue limits mask
block: bump BLK_DEF_MAX_SECTORS to 2560
Revert "block: remove artifical max_hw_sectors cap"
blk-mq: fix race between timeout and freeing request
blk-mq: fix buffer overflow when reading sysfs file of 'pending'
Documentation: update notes in biovecs about arbitrarily sized bios
block: remove bio_get_nr_vecs()
fs: use helper bio_add_page() instead of open coding on bi_io_vec
block: kill merge_bvec_fn() completely
md/raid5: get rid of bio_fits_rdev()
md/raid5: split bio for chunk_aligned_read
block: remove split code in blkdev_issue_{discard,write_same}
btrfs: remove bio splitting and merge_bvec_fn() calls
bcache: remove driver private bio splitting code
block: simplify bio_add_page()
block: make generic_make_request handle arbitrarily sized bios
blk-cgroup: Drop unlikely before IS_ERR(_OR_NULL)
block: don't access bio->bi_error after bio_put()
block: shrink struct bio down to 2 cache lines again
...
|
|
Pull first round of SCSI updates from James Bottomley:
"This includes one new driver: cxlflash plus the usual grab bag of
updates for the major drivers: qla2xxx, ipr, storvsc, pm80xx, hptiop,
plus a few assorted fixes.
There's another tranch coming, but I want to incubate it another few
days in the checkers, plus it includes a mpt2sas separated lifetime
fix, which Avago won't get done testing until Friday"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (85 commits)
aic94xx: set an error code on failure
storvsc: Set the error code correctly in failure conditions
storvsc: Allow write_same when host is windows 10
storvsc: use storage protocol version to determine storage capabilities
storvsc: use correct defaults for values determined by protocol negotiation
storvsc: Untangle the storage protocol negotiation from the vmbus protocol negotiation.
storvsc: Use a single value to track protocol versions
storvsc: Rather than look for sets of specific protocol versions, make decisions based on ranges.
cxlflash: Remove unused variable from queuecommand
cxlflash: shift wrapping bug in afu_link_reset()
cxlflash: off by one bug in cxlflash_show_port_status()
cxlflash: Virtual LUN support
cxlflash: Superpipe support
cxlflash: Base error recovery support
qla2xxx: Update driver version to 8.07.00.26-k
qla2xxx: Add pci device id 0x2261.
qla2xxx: Fix missing device login retries.
qla2xxx: do not clear slot in outstanding cmd array
qla2xxx: Remove decrement of sp reference count in abort handler.
qla2xxx: Add support to show MPI and PEP FW version for ISP27xx.
...
|
|
Pull MTD updates from Brian Norris:
"SPI NOR:
- reduce virtual address space requirements for fsl-quadspi memory map
- new fsl-quadspi IP support: imx6ul-qspi and imx7d-qspi
- add new NOR flash device support
- add new driver for NXP SPI Flash Interface (SPIFI)
- stop abusing SPI API structs for non-SPI framework
- fixup DT table matching for new "jedec,spi-nor" string
NAND:
- brcmnand: fix big endian MIPS macro usage
- denali: refactor to use devres, dev_*() printing, etc.
- OMAP ELM: change the module alias to actually be usable
- pxa3xx_nand: fixup a few command sequencing issues -- both new and old
- race conditions in the IRQ handler status clearing
- problems when a bootloader left interrupts pending
- config issues when overriding the bootloader configuration
- new flash device support
- sunxi_nand:
- optimize timing configuration by calculation, rather than fixed
fail-safe values
- use EDO setting from ONFI
- r852: fix compiler warnings
- davinci: add 4KB page support
Core:
- oobtest: correct debug print information"
* tag 'for-linus-20150901' of git://git.infradead.org/linux-mtd: (42 commits)
mtd: mtd_oobtest: Fix the address offset with vary_offset case
mtd: blkdevs: fix switch-bool compilation warning
mtd: spi-nor: stop (ab)using struct spi_device_id
mtd: nand: add Toshiba TC58NVG0S3E to nand_ids table
mtd: dataflash: Export OF module alias information
nand: pxa3xx: Increase READ_ID buffer and make the size static
mtd: nand: pxa3xx-nand: fix random command timeouts
mtd: nand: pxa3xx_nand: fix early spurious interrupt
mtd: pxa3xx_nand: add a default chunk size
mtd: omap_elm: Fix module alias
mtd: physmap_of: fix null pointer deference when kzalloc returns null
mtd: nettel: do not ignore mtd_device_register() failure in nettel_init()
mtd: denali_pci: switch to dev_err()
mtd: denali_pci: refactor driver using devres API
mtd: denali_pci: use module_pci_driver() macro
mtd: denali: hide core part from user in Kconfig
mtd: spi-nor: add Spansion S25FL204K support
mtd: spi-nor: Improve Kconfig help text for SPI_FSL_QUADSPI
mtd: spi-nor: add driver for NXP SPI Flash Interface (SPIFI)
doc: dt: add documentation for nxp,lpc1773-spifi
...
|
|
Xen's PV network protocol includes messages to add/remove ethernet
multicast addresses to/from a filter list in the backend. This allows
the frontend to request the backend only forward multicast packets
which are of interest thus preventing unnecessary noise on the shared
ring.
The canonical netif header in git://xenbits.xen.org/xen.git specifies
the message format (two more XEN_NETIF_EXTRA_TYPEs) so the minimal
necessary changes have been pulled into include/xen/interface/io/netif.h.
To prevent the frontend from extending the multicast filter list
arbitrarily a limit (XEN_NETBK_MCAST_MAX) has been set to 64 entries.
This limit is not specified by the protocol and so may change in future.
If the limit is reached then the next XEN_NETIF_EXTRA_TYPE_MCAST_ADD
sent by the frontend will be failed with NETIF_RSP_ERROR.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a5597008dbc2 ("phy: fixed_phy: Add gpio to determine link up/down.")
added a new argument to fixed_phy_register(), but missed to update bgmac
driver, causing the following build failure:
drivers/net/ethernet/broadcom/bgmac.c:1450:2: error: too few arguments to function 'fixed_phy_register'
Add the missing argument.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flags to ibnl_put_msg should be NLM_F_REQUEST instead of GFP_KERNEL.
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: John Fleck <john.fleck@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Customize the insert_nop func for SDMA rings, and use burst NOP for
ring/IB submissions in other places as well
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The insert_nop function is added to amdgpu_ring_funcs structure as
well as the default implementation
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This function is added to map the ring to sdma instance
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove the hardcoded usage
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The burst NOP is supported for SDMA when feature_version is >= 20.
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This is added to support the burst NOP
v2: squash the typo fix
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Instead of the array which is used for ID management.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
|
|
with interruptible, the push_job maybe return -ERESTARTSYS,
then result in push_job error.
E.g. bug trace:
[ 181.618860] *****amdgpu_copy_buffer:fence->seq:0x0000000048d8758b, contxt:1207959552, ref:683967304, r:-512
[ 181.618929] BUG: unable to handle kernel paging request at ffffffff811aa266
[ 181.625887] IP: [<ffffffff81548ffc>] reservation_object_add_excl_fence+0x3c/0x120
...
[ 181.859767] [<ffffffff811aa266>] ? unmap_mapping_range+0x66/0x110
[ 181.865928] [<ffffffffc0608ac1>] ttm_bo_move_accel_cleanup+0x41/0x3c0 [ttm]
[ 181.872971] [<ffffffffc062d382>] amdgpu_move_blit.isra.18+0x122/0x150 [amdgpu]
[ 181.880254] [<ffffffff811aa266>] ? unmap_mapping_range+0x66/0x110
[ 181.886420] [<ffffffffc062d709>] amdgpu_bo_move+0xa9/0x200 [amdgpu]
[ 181.892753] [<ffffffffc0606e8d>] ttm_bo_handle_move_mem+0x26d/0x5c0 [ttm]
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
No copy_(to|from)_user while BO is reserved.
v2: handle default path as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
|
|
amdgpu_fence_wait_multiple()" v2
That isn't used any more.
v2: rebase
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
With the radeon driver loaded the HP Compaq dc5750
Small Form Factor machine fails to resume from suspend.
Adding a quirk similar to other devices avoids
the problem and the system resumes properly.
Signed-off-by: Jeffery Miller <jmiller@neverware.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
sync_resv is to handle both amdgpu_fence and sched_fence.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
|
|
AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Port of:
drm/radeon/atom: Send out the full AUX address
to amdgpu
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"Nothing interesting. A couple device specific minor updates and a
kernel doc change"
* 'for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: pata_arasam_cf: Use devm_clk_get
libata: fix libata-core.c kernel-doc warning
ata: sata_rcar: Remove obsolete sata-r8a779* platform_device_id entries
|
|
Looking other drm drivers, there is no the restriction that framebuffer
has only one buffer in .create_handle() callback. They use just first
buffer.
If this limitation is removed, there is no reason keeping buffer count
for framebuffer, so we can remove buf_cnt from struct exynos_drm_fb.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
We can get buffer count of framebuffer using drm_format_num_planes(), so
keeping exynos_drm_fb_get_buf_cnt() is unnecessary.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Using exynos_drm_framebuffer_init(), redundant codes can be removed.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This modifies exynos_drm_framebuffer_init() to be possible to support
multiple buffers. Then it can be used by exynos_user_fb_create().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Current codes get first gem object and then again get remain gem
objects. They can be unified to one routine.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch moves codes to update fb_info into exynos_drm_fbdev_update(),
so fb_info is updated via only one function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
It can get exynos_gem object via function argument, so no need to call
exynos_drm_fb_gem_obj() in exynos_drm_fbdev_update.
It also can get struct drm_framebuffer *fb via helper->fb, so can remove
a function argument for it.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The variable name "exynos_gem_obj" is too long, so some lines exceed 80
characters. It's simple to use "obj" instead of "exynos_gem_obj".
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The exynos_drm_fb_set_buf_cnt() is used to set buffer count only in
exynos_drm_fbdev_update(). This patch sets directly buffer count in
exynos_drm_framebuffer_init() without using exynos_drm_fb_set_buf_cnt(),
so there is no any reason to keep exynos_drm_fb_set_buf_cnt().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The cases of the switch statement ensure that reg_type
can never be REG_TYPE_NONE here.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The size check was incomplete. It only computed the
size of area of the drawing rectangle and checked if
the size still fit inside the buffer.
The correct check is to compute the position of the
last byte that the G2D engine is going to access and
then check if that position is still contained in the
buffer. In particular we need the stride information
to determine this.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Pass the correct hpd[] array to intel_get_hpd_pins() on pre-g4x
platforms.
This got broken in the following commit:
commit fd63e2a972c670887e5e8a08440111d3812c0996
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Jul 21 15:32:44 2015 -0700
drm/i915: combine i9xx_get_hpd_pins and pch_get_hpd_pins
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Egbert Eich <eich@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
There have been many hard to track down bugs whereby userspace forgot to
flag a write buffer and then cause graphics corruption or a hung GPU
when that buffer was later purged under memory pressure (as the buffer
appeared clean, its pages would have been evicted rather than preserved
and any changes more recent than in the backing storage would be lost).
In retrospect this is a rare optimisation against memory pressure,
already the slow path. If we always mark the buffer as dirty when
accessed by the GPU, anything not used can still be evicted cheaply
(ideal behaviour for mark-and-sweep eviction) but we do not run the risk
of corruption. For correct read serialisation, userspace still has to
notify when the GPU writes to an object. However, there are certain
situations under which userspace may wish to tell white lies to the
kernel...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: "Goel, Akash" <akash.goel@intel.co>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
To help with debugging i2c-over-aux issues, add a module parameter than
can be used to tweak the assumed i2c bus speed, and thus the maximum
number of retries we will do for each aux message.
Cc: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: moosotc@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Calculate the number of retries we should do for each i2c-over-aux
message based on the time it takes to perform the i2c transfer vs. the
aux transfer. We assume the shortest possible length for the aux
transfer, and the longest possible (exluding clock stretching) for the
i2c transfer.
The DP spec has some examples on how to calculate this, but we don't
calculate things quite the same way. The spec doesn't account for the
retry interval (assumes immediate retry on defer), and doesn't assume
the best/worst case behaviour as we do.
Note that currently we assume 10 kHz speed for the i2c bus. Some real
world devices (eg. some Apple DP->VGA dongle) fails with less than 16
retries. and that would correspond to something close to 15 kHz (with
our method of calculating things) But let's just go for 10 kHz to be
on the safe side. Ideally we should query/set the i2c bus speed via
DPCD but for now this should at leaast remove the regression from the
1->16 byte trasnfer size change. And of course if the sink completes
the transfer quicker this shouldn't slow things down since we don't
change the interval between retries.
I did a few experiments with a DP->DVI dongle I have that allows you
to change the i2c bus speed. Here are the results of me changing the
actual bus speed and the assumed bus speed and seeing when we start
to fail the operation:
actual i2c khz assumed i2c khz max retries
1 1 ok -> 2 fail 211 ok -> 106 fail
5 8 ok -> 9 fail 27 ok -> 24 fail
10 17 ok -> 18 fail 13 ok -> 12 fail
100 210 ok -> 211 fail 2 ok -> 1 fail
So based on that we have a fairly decent safety margin baked into
the formula to calculate the max number of retries.
Fixes a regression with some DP dongles from:
commit 1d002fa720738bcd0bddb9178e9ea0773288e1dd
Author: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Date: Tue Feb 10 18:38:08 2015 +0000
drm/dp: Use large transactions for I2C over AUX
v2: Use best case for AUX and worst case for i2c (Simon Farnsworth)
Add a define our AUX retry interval and account for it
v3: Make everything usecs to avoid confusion about units (Daniel)
Add a comment reminding people about the AUX bitrate (Daniel)
Use DIV_ROUND_UP() since we're after the "worst" case for i2c
Cc: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: moosotc@gmail.com
Tested-by: moosotc@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91451
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
