| Age | Commit message (Collapse) | Author |
|---|
|
There are some useless type cast, print in hclge_cmd_send.
This patch removes them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hclge_ring_to_dma_dir is unused anywhere.
This patch removes it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pointer zatm_dev is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'zatm_dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL8211C has an issue when operating in Gigabit slave mode, therefore
genphy driver can't be used. See also this U-boot change.
https://lists.denx.de/pipermail/u-boot/2016-March/249712.html
Add a PHY driver for this chip with the quirk to force Gigabit master
mode. As a note: This will make it impossible to connect two network
ports directly which both are driven by a RTl8211C.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc 8.1.0 complains:
drivers/isdn/i4l/isdn_tty.c: In function 'isdn_tty_suspend.isra.1':
drivers/isdn/i4l/isdn_tty.c:790:3: warning:
'strncpy' output truncated before terminating nul copying
as many bytes from a string as its length
drivers/isdn/i4l/isdn_tty.c:778:6: note: length computed here
drivers/isdn/i4l/isdn_tty.c: In function 'isdn_tty_resume':
drivers/isdn/i4l/isdn_tty.c:880:3: warning:
'strncpy' output truncated before terminating nul copying
as many bytes from a string as its length
drivers/isdn/i4l/isdn_tty.c:817:6: note: length computed here
Using strncpy() is indeed less than perfect since the length of data to
be copied has already been determined with strlen(). Replace strncpy()
with memcpy() to address the warning and optimize the code a little.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding support for RTL8211 I forgot to update the mdio_device_id
table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: d241d4aac93f ("net: phy: realtek: add support for RTL8211")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This hack (affecting the non-PCIe models only) was introduced in 2004
to deal with link negotiation failures in 1GBit mode. Based on a
comment in the r8169 vendor driver I assume the issue affects RTL8169sb
in combination with particular 1GBit switch models.
Resetting the PHY every 10s and hoping that one fine day we will make
it to establish the link seems to be very hacky to me. I'd say:
If 1GBit doesn't work reliably in a users environment then the user
should remove 1GBit from the advertised modes, e.g. by using
ethtool -s <if> advertise <10/100 modes>
If the issue affects one chip version only and that with most link
partners, then we could also think of removing 1GBit from the
advertised modes for this chip version in the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode),
get-tsinfo() callback should return the software timestamp capabilities
instead of returning the error.
Fixes: 4c55215c ("qede: Add driver support for PTP")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the correct size value while copying chassis/port id values.
Fixes: 6ad8c632e ("qed: Add support for query/config dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After we change the ipvlan mode from l3 to l2, or vice versa, we only
reset IFF_NOARP flag, but don't flush the ARP table cache, which will
cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2().
Then the message will not come out of host.
Here is the reproducer on local host:
ip link set eth1 up
ip addr add 192.168.1.1/24 dev eth1
ip link add link eth1 ipvlan1 type ipvlan mode l3
ip netns add net1
ip link set ipvlan1 netns net1
ip netns exec net1 ip link set ipvlan1 up
ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1
ip route add 192.168.2.0/24 via 192.168.1.2
ping 192.168.2.2 -c 2
ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2
ping 192.168.2.2 -c 2
Add the same configuration on remote host. After we set the mode to l2,
we could find that the src/dst MAC addresses are the same on eth1:
21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64
Fix this by calling dev_change_flags(), which will call netdevice notifier
with flag change info.
v2:
a) As pointed out by Wang Cong, check return value for dev_change_flags() when
change dev flags.
b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops.
So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if sa_idx is equal to NSIM_IPSEC_MAX_SA_COUNT then
an out-of-bounds read on ipsec->sa will occur. Fix the
incorrect bounds check by using >= rather than >.
Detected by CoverityScan, CID#1470226 ("Out-of-bounds-read")
Fixes: 7699353da875 ("netdevsim: add ipsec offload testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.
Commit 5f114163f2f5 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.
This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.
Fixes: 5f114163f2f5 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adjusts the allocator calls to use 2-factor argument call style, as
done treewide already for improved defense against allocation overflows.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Reduce the default values for the number of hardware queues and queue depth
to significantly reduce the memory footprint of a DASD device.
The memory consumption per DASD device reduces from approximately 40MB to
approximately 1.5MB.
This is necessary to build systems with a large number of DASD devices and
a reasonable amount of memory.
Performance measurements showed that good performance results are possible
with the new default values even on systems with lots of CPUs and lots of
alias devices.
Fixes: e443343e509a ("s390/dasd: blk-mq conversion")
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Dan Carpenter reported an integer underflow issue in the rtl8188eu driver.
This is also needed for the length (signed integer) in rtl8723bs, as it is
later converted to an unsigned integer and used in a memcpy operation.
Original issue is at https://patchwork.kernel.org/patch/9796371/
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Murray McAllister <murray.mcallister@insomniasec.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
changed gvt display transcode DDI mode from DP_SST to
DVI to address below calltrace issue during guest booting
up which is caused by zero dotclock initial value with DP_SST
mode. transcode DVI mode emulation also align with native with DP
connection.
[drm:drm_calc_timestamping_constants]
ERROR crtc 41: Can't calculate constants, dotclock = 0!
WARNING: at drivers/gpu/drm/drm_vblank.c:620
drm_calc_vbltimestamp_from_scanoutpos
Call Trace:
? drm_calc_timestamping_constants+0x144/0x150 [drm]
drm_get_last_vbltimestamp+0x54/0x90 [drm]
drm_reset_vblank_timestamp+0x59/0xd0 [drm]
drm_crtc_vblank_on+0x7b/0xd0 [drm]
intel_modeset_setup_hw_state+0xb67/0xfd0 [i915]
? gen2_read32+0x110/0x110 [i915]
? drm_modeset_lock+0x30/0xa0 [drm]
intel_modeset_init+0x794/0x19d0 [i915]
? intel_setup_gmbus+0x232/0x2e0 [i915]
i915_driver_load+0xb4a/0xf40 [i915]
Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
when guest writes ggtt entries, it could write 8 bytes a time if
gtt_entry_size is 8. But, qemu could split the 8 bytes into 2 consecutive
4-byte writes.
If each 4-byte partial write could trigger a host ggtt write, it is very
possible that a wrong combination is written to the host ggtt. E.g.
the higher 4 bytes is the old value, but the lower 4 bytes is the new
value, and this 8-byte combination is wrong but written to the ggtt, thus
causing bugs.
To handle this condition, we just record the first 4-byte write, then wait
until the second 4-byte write comes and write the combined 64-bit data to
host ggtt table.
To save memory space and to spot partial write as early as possible, we
don't keep this information for every ggtt index. Instread, we just record
the last ggtt write position, and assume the two 4-byte writes come in
consecutively for each vgpu.
This assumption is right based on the characteristic of ggtt entry which
stores memory address. When gtt_entry_size is 8, the guest memory physical
address should be 64 bits, so any sane guest driver should write 8-byte
long data at a time, so 2 consecutive 4-byte writes at the same ggtt index
should be trapped in gvt.
v2:
when incomplete ggtt entry write is located, e.g.
1. guest only writes 4 bytes at a ggtt offset and no long writes the
rest 4 bytes.
2. guest writes 4 bytes of a ggtt offset, then write at other ggtt
offsets, then return back to write the left 4 bytes of the first
ggtt offset.
add error handling logic to remap host entry to scratch page, and mark
guest virtual ggtt entry as not present. (zhenyu wang)
Signed-off-by: Zhao Yan <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch unifies the naming of DRM functions for reference counting
of struct drm_framebuffer. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems"
* tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: ion: Return an ERR_PTR in ion_map_kernel
staging: comedi: quatech_daqp_cs: fix no-op loop daqp_ao_insn_write()
iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machines
iio: buffer: fix the function signature to match implementation
iio: mma8452: Fix ignoring MMA8452_INT_DRDY
iio: tsl2x7x/tsl2772: avoid potential division by zero
iio: pressure: bmp280: fix relative humidity unit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are five fixes for the tty core and some serial drivers.
The tty core ones fix some security and other issues reported by the
syzbot that I have taken too long in responding to (sorry Tetsuo!).
The 8350 serial driver fix resolves an issue of devices that used to
work properly stopping working as they shouldn't have been added to a
blacklist.
All of these have been in linux-next for a few days with no reported
issues"
* tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: prevent leaking uninitialized data to userspace via /dev/vcs*
serdev: fix memleak on module unload
serial: 8250_pci: Remove stalled entries in blacklist
n_tty: Access echo_* variables carefully.
n_tty: Fix stall at n_tty_receive_char_special().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of USB gadget and other driver fixes for 4.18-rc3.
There's a bunch of them here, most of them being gadget driver and
xhci host controller fixes for reported issues (as normal), but there
are also some new device ids, and some fixes for the typec code.
There is an acpi core patch in here that was acked by the acpi
maintainer as it is needed for the typec fixes in order to properly
solve a problem in that driver.
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: host: fix disconnection detect issue
usb: typec: tcpm: fix logbuffer index is wrong if _tcpm_log is re-entered
typec: tcpm: Fix a msecs vs jiffies bug
NFC: pn533: Fix wrong GFP flag usage
usb: cdc_acm: Add quirk for Uniden UBC125 scanner
staging/typec: fix tcpci_rt1711h build errors
usb: typec: ucsi: Fix for incorrect status data issue
usb: typec: ucsi: acpi: Workaround for cache mode issue
acpi: Add helper for deactivating memory region
usb: xhci: increase CRS timeout value
usb: xhci: tegra: fix runtime PM error handling
usb: xhci: remove the code build warning
xhci: Fix kernel oops in trace_xhci_free_virt_device
xhci: Fix perceived dead host due to runtime suspend race with event handler
dwc2: gadget: Fix ISOC IN DDMA PID bitfield value calculation
usb: gadget: dwc2: fix memory leak in gadget_init()
usb: gadget: composite: fix delayed_status race condition when set_interface
usb: dwc2: fix isoc split in transfer with no data
usb: dwc2: alloc dma aligned buffer for isoc split in
usb: dwc2: fix the incorrect bitmaps for the ports of multi_tt hub
...
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-07-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) A bpf_fib_lookup() helper fix to change the API before freeze to
return an encoding of the FIB lookup result and return the nexthop
device index in the params struct (instead of device index as return
code that we had before), from David.
2) Various BPF JIT fixes to address syzkaller fallout, that is, do not
reject progs when set_memory_*() fails since it could still be RO.
Also arm32 JIT was not using bpf_jit_binary_lock_ro() API which was
an issue, and a memory leak in s390 JIT found during review, from
Daniel.
3) Multiple fixes for sockmap/hash to address most of the syzkaller
triggered bugs. Usage with IPv6 was crashing, a GPF in bpf_tcp_close(),
a missing sock_map_release() routine to hook up to callbacks, and a
fix for an omitted bucket lock in sock_close(), from John.
4) Two bpftool fixes to remove duplicated error message on program load,
and another one to close the libbpf object after program load. One
additional fix for nfp driver's BPF offload to avoid stopping offload
completely if replace of program failed, from Jakub.
5) Couple of BPF selftest fixes that bail out in some of the test
scripts if the user does not have the right privileges, from Jeffrin.
6) Fixes in test_bpf for s390 when CONFIG_BPF_JIT_ALWAYS_ON is set
where we need to set the flag that some of the test cases are expected
to fail, from Kleber.
7) Fix to detangle BPF_LIRC_MODE2 dependency from CONFIG_CGROUP_BPF
since it has no relation to it and lirc2 users often have configs
without cgroups enabled and thus would not be able to use it, from Sean.
8) Fix a selftest failure in sockmap by removing a useless setrlimit()
call that would set a too low limit where at the same time we are
already including bpf_rlimit.h that does the job, from Yonghong.
9) Fix BPF selftest config with missing missing NET_SCHED, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5088814a6e93 (ACPICA: AML parser: attempt to continue loading
table after error) unintentionally added leading newlines to error
messages emitted by ACPICA which caused unexpected things to be
printed to the kernel log. Drop these newlines (which effectively
reverts the part of commit 5088814a6e93 adding them).
Fixes: 5088814a6e93 (ACPICA: AML parser: attempt to continue loading table after error)
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is reported that commit c62ec4610c40 (PM / core: Fix direct_complete
handling for devices with no callbacks) introduced a system suspend
regression on Samsung 305V4A by allowing a PCI bridge (not a PCIe
port) to stay in D3 over suspend-to-RAM, which is a side effect of
setting power.direct_complete for the children of that bridge that
have no PM callbacks.
On the majority of systems PCI bridges are not allowed to be
runtime-suspended (the power/control sysfs attribute is set to "on"
for them by default), but user space can change that setting and if
it does so and a given bridge has no children with PM callbacks, the
direct_complete optimization will be applied to it and it will stay
in suspend over system suspend. Apparently, that confuses the
platform firmware on the affected machine and that may very well
happen elsewhere, so avoid the direct_complete optimization for
PCI bridges with no drivers (if there is a driver, it should take
care of the PM handling) on suspend-to-RAM altogether (that should
not matter for suspend-to-idle as platform firmware is not involved
in it).
Fixes: c62ec4610c40 (PM / core: Fix direct_complete handling for devices with no callbacks)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199941
Reported-by: n0000b.n000b@gmail.com
Tested-by: n0000b.n000b@gmail.com
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The patch noted in the fixes below converted get_user_pages_fast() to
get_user_pages_longterm(), however the two calls differ in a few ways.
First _fast() is documented to not require the mmap_sem, while _longterm()
is documented to need it. Hold the mmap sem as required.
Second, _fast accepts an 'int write' while _longterm uses 'unsigned int
gup_flags', so the expression '!!(prot & IOMMU_WRITE)' is only working by
luck as FOLL_WRITE is currently == 0x1. Use the expected FOLL_WRITE
constant instead.
Fixes: 94db151dc892 ("vfio: disable filesystem-dax page pinning")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Pull block fixes from Jens Axboe:
"Small set of fixes for this series. Mostly just minor fixes, the only
oddball in here is the sg change.
The sg change came out of the stall fix for NVMe, where we added a
mempool and limited us to a single page allocation. CONFIG_SG_DEBUG
sort-of ruins that, since we'd need to account for that. That's
actually a generic problem, since lots of drivers need to allocate SG
lists. So this just removes support for CONFIG_SG_DEBUG, which I added
back in 2007 and to my knowledge it was never useful.
Anyway, outside of that, this pull contains:
- clone of request with special payload fix (Bart)
- drbd discard handling fix (Bart)
- SATA blk-mq stall fix (me)
- chunk size fix (Keith)
- double free nvme rdma fix (Sagi)"
* tag 'for-linus-20180629' of git://git.kernel.dk/linux-block:
sg: remove ->sg_magic member
drbd: Fix drbd_request_prepare() discard handling
blk-mq: don't queue more if we get a busy return
block: Fix cloning of requests with a special payload
nvme-rdma: fix possible double free of controller async event buffer
block: Fix transfer when chunk sectors exceeds max
|
|
cmd_rc is passed in by reference to the acpi_nfit_ctl() function and the
caller expects a value returned. However, when the package is pass through
via the ND_CMD_CALL command, cmd_rc is not touched. Make sure cmd_rc is
always set.
Fixes: aef253382266 ("libnvdimm, nfit: centralize command status translation")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Currently the NFP fw only supports L3/L4 hashing so rejects the offload of
filters that output to LAG ports implementing other hash algorithms. Team,
however, uses a BPF function for the hash that is not defined. To support
Team offload, accept hashes that are defined as 'unknown' (only Team
defines such hash types). In this case, use the NFP default of L3/L4
hashing for egress port selection.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the tos and the tunnel flags from the tunnel key and offload these
action fields. Only the checksum and tunnel key flags are implemented in
fw so reject offloads of other flags. The tunnel key flag is always
considered set in the fw so enforce that it is set in the rule. Note that
the compulsory setting of the tunnel key flag and optional setting of
checksum is inline with how tc currently generates ipv4 udp tunnel
actions.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the ttl for ipv4 udp tunnels was set to the namespace default.
Modify this to attempt to extract the ttl from a full route lookup on the
tunnel destination. If this is not possible then resort to the default.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware will automatically update csum in headers when a set action has
been performed. This means we could in the driver ignore the explicit
checksum action when performing a set action.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used to leave bus-info in ethtool driver info empty for
representors in case multi-PCIe-to-single-host cards make
the association between PCIe device and NFP many to one.
It seems these attempts are futile, we need to link the
representors to one PCIe device in sysfs to get consistent
naming, plus devlink uses one PCIe as a handle, anyway.
The multi-PCIe-to-single-system support won't be clean,
if it ever comes.
Turns out some user space (RHEL tests) likes to read bus-info
so just populate it.
While at it remove unnecessary app NULL-check, representors
are spawned by an app, so it must exist.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_consume_skb() in nfp_net_tx_complete() to get bulk free.
Pass 0 as budget for ctrl queue completion since it runs out of
a tasklet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP NAPI handling will only complete the TXed packets when called
with budget of 0, implement ndo_poll_controller by scheduling NAPI
on all TX queues.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some platforms with broken ACPI tables we may not have access
to the Serial Number PCIe capability. This capability is crucial
for us for switchdev operation as we use serial number as switch ID,
and for communication with management FW where interface ID is used.
If we can't determine the Serial Number we have to fail device probe.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After user changes the ring count statistics for deactivated
rings disappear from ethtool -S output. This causes loss of
information to the user and means that ethtool stats may not
add up to interface stats. Always expose counters from all
the rings. Note that we allocate at most num_possible_cpus()
rings so number of rings should be reasonable.
The alternative of only listing stats for rings which were
ever in use could be confusing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing device hotplug the sub channel must be async to avoid
deadlock issues because device is discovered in softirq context.
When doing changes to MTU and number of channels, the setup
must be synchronous to avoid races such as when MTU and device
settings are done in a single ip command.
Reported-by: Thomas Walker <Thomas.Walker@twosigma.com>
Fixes: 8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug")
Fixes: 732e49850c5e ("netvsc: fix race on sub channel creation")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pool can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/zatm.c:1491 zatm_ioctl() warn: potential spectre issue
'zatm_dev->pool_info' (local cap)
Fix this by sanitizing pool before using it to index
zatm_dev->pool_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit e830baa9c3f0 ("qeth: restore device features after recovery") and
commit ce3443564145 ("s390/qeth: rely on kernel for feature recovery")
made sure that the HW functions for device features get re-programmed
after recovery.
But we missed that the same handling is also required when a card is
first set offline (destroying all HW context), and then online again.
Fix this by moving the re-enable action out of the recovery-only path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If qeth_qdio_output_handler() detects that a transmit requires async
completion, it replaces the pending buffer's metadata object
(qeth_qdio_out_buffer) so that this queue buffer can be re-used while
the data is pending completion.
Later when the CQ indicates async completion of such a metadata object,
qeth_qdio_cq_handler() tries to free any data associated with this
object (since HW has now completed the transfer). By calling
qeth_clear_output_buffer(), it erronously operates on the queue buffer
that _previously_ belonged to this transfer ... but which has been
potentially re-used several times by now.
This results in double-free's of the buffer's data, and failing
transmits as the buffer descriptor is scrubbed in mid-air.
The correct way of handling this situation is to
1. scrub the queue buffer when it is prepared for re-use, and
2. later obtain the data addresses from the async-completion notifier
(ie. the AOB), instead of the queue buffer.
All this only affects qeth devices used for af_iucv HiperTransport.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
*ether_addr*_64bits functions have been introduced to optimize
performance critical paths, which access 6-byte ethernet address as u64
value to get "nice" assembly. A harmless hack works nicely on ethernet
addresses shoved into a structure or a larger buffer, until busted by
Kasan on smth like plain (u8 *)[6].
qeth_l2_set_mac_address calls qeth_l2_remove_mac passing
u8 old_addr[ETH_ALEN] as an argument.
Adding/removing macs for an ethernet adapter is not that performance
critical. Moreover is_multicast_ether_addr_64bits itself on s390 is not
faster than is_multicast_ether_addr:
is_multicast_ether_addr(%r2) -> %r2
llc %r2,0(%r2)
risbg %r2,%r2,63,191,0
is_multicast_ether_addr_64bits(%r2) -> %r2
llgc %r2,0(%r2)
risbg %r2,%r2,63,191,0
So, let's just use is_multicast_ether_addr instead of
is_multicast_ether_addr_64bits.
Fixes: bcacfcbc82b4 ("s390/qeth: fix MAC address update sequence")
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When qeth_l2_set_mac_address() finds the card in a non-reachable state,
it merely copies the new MAC address into dev->dev_addr so that
__qeth_l2_set_online() can later register it with the HW.
But __qeth_l2_set_online() may very well be running concurrently, so we
can't trust the card state without appropriate locking:
If the online sequence is past the point where it registers
dev->dev_addr (but not yet in SOFTSETUP state), any address change needs
to be properly programmed into the HW. Otherwise the netdevice ends up
with a different MAC address than what's set in the HW, and inbound
traffic is not forwarded as expected.
This is most likely to occur for OSD in LPAR, where
commit 21b1702af12e ("s390/qeth: improve fallback to random MAC address")
now triggers eg. systemd to immediately change the MAC when the netdevice
is registered with a NET_ADDR_RANDOM address.
Fixes: bcacfcbc82b4 ("s390/qeth: fix MAC address update sequence")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b7493e91c11a757cf0f8ab26989642ee4bb2c642.
On its own, querying RDEV for a MAC address works fine. But when upgrading
from a qeth that previously queried DDEV on a z/VM NIC (ie. any kernel with
commit ec61bd2fd2a2), the RDEV query now returns a _different_ MAC address
than the DDEV query.
If the NIC is configured with MACPROTECT, z/VM apparently requires us to
use the MAC that was initially returned (on DDEV) and registered. So after
upgrading to a kernel that uses RDEV, the SETVMAC registration cmd for the
new MAC address fails and we end up with a non-operabel interface.
To avoid regressions on upgrade, switch back to using DDEV for the MAC
address query. The downgrade path (first RDEV, later DDEV) is fine, in this
case both queries return the same MAC address.
Fixes: b7493e91c11a ("s390/qeth: use Read device to query hypervisor for MAC")
Reported-by: Michal Kubecek <mkubecek@suse.com>
Tested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The __alx_open function can be called from ndo_open, which is called
under RTNL, or from alx_resume, which isn't. Since commit d768319cd427,
we're calling the netif_set_real_num_{tx,rx}_queues functions, which
need to be called under RTNL.
This is similar to commit 0c2cc02e571a ("igb: Move the calls to set the
Tx and Rx queues into igb_open").
Fixes: d768319cd427 ("alx: enable multiple tx queues")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: fc7a6c287ff3 ("sfc: use a semaphore to lock farch filters too")
Suggested-by: Joseph Korty <joe.korty@concurrent-rt.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a bug where INT_STAT1 was written twice and
INT_STAT2 was ignored when disabling interrupts.
Fixes: b753a9faaf9a ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
