| Age | Commit message (Collapse) | Author |
|---|
|
wl1271_warning() already appends a \n to the format,
so adding one to the warning string gives empty lines in the log.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some features supported by firmware aren't advertised and there is no
way for a driver to query them. This includes e.g. monitor mode details.
Most firmwares support monitor interface but only the latest ones
/announce/ it with a "monitor" flag in the "cap" iovar. There isn't any
reliable detection method for older firmwares (BRCMF_C_MONITOR was tried
but "it only indicates the core part of the stack supports").
Similarly support for tagging monitor frames and building radiotap
headers can't be reliably detected for all firmwares.
This commit adds table that allows mapping features to firmware version.
It adds mappings for 43602a1 and 4366b1 firmwares from
linux-firmware.git. Both were confirmed to be passing monitor frames.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When CONFIG_PROC_FS isn't set, gcc warning this:
drivers/net/wireless/intersil/hostap/hostap_hw.c:2901:12: warning: ‘prism2_registers_proc_show’ defined but not used [-Wunused-function]
static int prism2_registers_proc_show(struct seq_file *m, void *v)
drivers/net/wireless/intersil/hostap/hostap_proc.c:16:12: warning: ‘prism2_debug_proc_show’ defined but not used [-Wunused-function]
static int prism2_debug_proc_show(struct seq_file *m, void *v)
^
drivers/net/wireless/intersil/hostap/hostap_proc.c:49:12: warning: ‘prism2_stats_proc_show’ defined but not used [-Wunused-function]
static int prism2_stats_proc_show(struct seq_file *m, void *v)
^
drivers/net/wireless/intersil/hostap/hostap_proc.c:177:12: warning: ‘prism2_crypt_proc_show’ defined but not used [-Wunused-function]
static int prism2_crypt_proc_show(struct seq_file *m, void *v)
^
fix this by adding #ifdef around them.
hfa384x_read_reg is only used by prism2_registers_proc_show,so move it
into #ifdef.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When CONFIG_PROC_FS isn't set, gcc warning this:
drivers/net/wireless/atmel/atmel.c:1402:12: warning: ‘atmel_proc_show’ defined but not used [-Wunused-function]
static int atmel_proc_show(struct seq_file *m, void *v)
^
fix this by adding #ifdef around it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pointer 'p' is being assigned but is never used hence it is
redundant and can be removed. Also re-work if statement to remove
redundant assignment of p.
Cleans up clang warning:
warning: variable 'p' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Variables id, unicast, write, conf, a_band, accum_tx and ucode are
assigned a value but it is never read, hence they are redundant and
can be removed.
Cleans up clang warnings:
warning: variable 'id' set but not used [-Wunused-but-set-variable]
warning: variable 'unicast' set but not used [-Wunused-but-set-variable]
warning: variable 'write' set but not used [-Wunused-but-set-variable]
warning: variable 'conf' set but not used [-Wunused-but-set-variable]
warning: variable 'a_band' set but not used [-Wunused-but-set-variable]
warning: variable 'tx' set but not used [-Wunused-but-set-variable]
warning: variable 'accum_tx' set but not used [-Wunused-but-set-variable]
warning: variable 'ucode' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Variables len, ret, reason and crypt are assigned values that
are never read, hence they are redundant and can be removed.
Note: For the variable ret, a return code is being assigned, but
this is not returned and 0 is currently being returned, I believe
this is OK.
Cleans up clang warnings:
warning: variable 'len' set but not used [-Wunused-but-set-variable]
variable 'ret' set but not used [-Wunused-but-set-variable]
warning: variable 'reason' set but not used [-Wunused-but-set-variable]
warning: variable 'crypt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Variables len and dev assigned values but are never used hence they
are redundant and can be removed. Also add in white space in for-loop
and remove some { } braces on if statement.
Cleans up clang warnings:
warning: variable 'len' set but not used [-Wunused-but-set-variable]
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
common->init_done flag should set after basic initialization. Hence,
moving init_done flag at end of rsi_91x_init().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
rx_params are getting updated two times in driver, which is not required.
Hence, removing duplicate updation of rx_params from rsi_prepare_skb().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, RSI_NEEDED_HEADROOM is '80' for rsi driver, which is wrong.
As per rsi internal frame format, the RSI_NEEDED_HEADROOM shall be '84',
which is 64(dword_align) + 4(extended_desc) + 16(frame_desc).
Hence, corrected the needed headroom.
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, AP mode will work on only WLAN alone firmware. To give support
for AP and BT dual mode, adding firmware entry in 'struct ta_metadata'.
The firmware entry is based on what coex_mode is used in driver and coex
mode '4' for all AP+BT related functionalities. Hence, added the same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
while cleaning up the driver, observed that flash_content pointer is not
necessary in rsi_load_firmware(). Instead of this, driver can use
'fw_entry->data' directly.Hence, removed redundant flash_content pointer.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Removing redundant device id's from both usb and sdio idtables, as rsi
driver currently supporting only one module(RS9113). Also, replaced ids
with specific defines.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Due to multiple calls of add interface routine, vif is getting duplicated
and at certain instance, we are out of vifs, causing the driver to behave
abnormal.
Fix: Every vif has a unique mac-id, when we got a vif with same mac-id as
the previous id's, we will override the respective vif.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
System is unable to wake-up through magic-packet in secured connections.
Because key descriptor is getting corrupted and firmware is unable to
decrypt the magic packet. Fixed the issue by properly preparing it
before sending it to firmware.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Radio capabilities packet is not prepared properly for 40MHZ case,
ppe_ack_rate is a two byte variable which is initialized wrongly,
hence we are unable to connect, resolved by assigning it properly.
Signed-off-by: Ganapathi Raju <ganapathi.kondraju@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
observed low throughput rates during verification. This is because, QoS
enable flag is overridden by sequence number in the data descriptor frame.
Hence, added the fix for same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Mwifiex firmware inserts only Microsoft information element
Allow other vendor specific IEs to pass from userspace
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Driver is using boolean variables to maintain vairous status
information of adapter. These status variables are accessed by
multiple threads and there is a possibility of a race. To avoid
this, convert these variables to a set of bitops flags, to be
operated atomically.
Below variables of mwifiex_adapter are converted to bitop flags:
surprise_removed
is_cmd_timedout
is_suspended
is_hs_configured
hs_enabling
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Driver must ensure that whenever it holds a pointer to the list
entry mwifiex_rx_reorder_tbl, it must protect the same with
rx_reorder_tbl_lock. At present there are many places where
driver does not ensure this. To cover all cases, spinlocks in
below funcions are moved out and made sure that the caller will
hold the spinlock:
mwifiex_11n_dispatch_pkt_until_start_win()
mwifiex_11n_scan_and_dispatch()
mwifiex_del_rx_reorder_entry()
mwifiex_11n_get_rx_reorder_tbl()
mwifiex_11n_find_last_seq_num()
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
At present driver spinlock protects iteration of list
rx_reorder_tbl_ptr with rx_reorder_tbl_lock. To protect the
individual items in this list, it uses rx_pkt_lock. But, we can
use a single rx_reorder_tbl_lock for both purposes. This patch
replaces rx_pkt_lock by rx_reorder_tbl_lock.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull networking fixes from David Miller:
"Several smallish fixes, I don't think any of this requires another -rc
but I'll leave that up to you:
1) Don't leak uninitialzed bytes to userspace in xfrm_user, from Eric
Dumazet.
2) Route leak in xfrm_lookup_route(), from Tommi Rantala.
3) Premature poll() returns in AF_XDP, from Björn Töpel.
4) devlink leak in netdevsim, from Jakub Kicinski.
5) Don't BUG_ON in fib_compute_spec_dst, the condition can
legitimately happen. From Lorenzo Bianconi.
6) Fix some spectre v1 gadgets in generic socket code, from Jeremy
Cline.
7) Don't allow user to bind to out of range multicast groups, from
Dmitry Safonov with a follow-up by Dmitry Safonov.
8) Fix metrics leak in fib6_drop_pcpu_from(), from Sabrina Dubroca"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
netlink: Don't shift with UB on nlk->ngroups
net/ipv6: fix metrics leak
xen-netfront: wait xenbus state change when load module manually
can: ems_usb: Fix memory leak on ems_usb_disconnect()
openvswitch: meter: Fix setting meter id for new entries
netlink: Do not subscribe to non-existent groups
NET: stmmac: align DMA stuff to largest cache line length
tcp_bbr: fix bw probing to raise in-flight data for very small BDPs
net: socket: Fix potential spectre v1 gadget in sock_is_registered
net: socket: fix potential spectre v1 gadget in socketcall
net: mdio-mux: bcm-iproc: fix wrong getter and setter pair
ipv4: remove BUG_ON() from fib_compute_spec_dst
enic: handle mtu change for vf properly
net: lan78xx: fix rx handling before first packet is send
nfp: flower: fix port metadata conversion bug
bpf: use GFP_ATOMIC instead of GFP_KERNEL in bpf_parse_prog()
bpf: fix bpf_skb_load_bytes_relative pkt length check
perf build: Build error in libbpf missing initialization
net: ena: Fix use of uninitialized DMA address bits field
bpf: btf: Use exact btf value_size match in map_check_btf()
...
|
|
This patch implements following ethtool stats fields for netvsc:
cpu<n>_tx/rx_packets/bytes
cpu<n>_vf_tx/rx_packets/bytes
Corresponding per-cpu counters already exist in current code. Exposing
these counters will help troubleshooting performance issues.
for_each_present_cpu() was used instead of for_each_possible_cpu().
for_each_possible_cpu() would create very long and useless output.
It is still being used for internal buffer, but not for ethtool
output.
There could be an overflow if cpu was added between ethtool
call netvsc_get_sset_count() and netvsc_get_ethtool_stats() and
netvsc_get_strings(). (still safe if cpu was removed)
ethtool makes these three function calls separately.
As long as we use ethtool, I can't see any clean solution.
Currently and in foreseeable short term, Hyper-V doesn't support
cpu hot-plug. Plus, ethtool is for admin use. Unlikely the admin
would perform such combo operations.
Changes in v2:
- Remove cpp style comment
- Resubmit after freeze
Changes in v3:
- Reimplemented with kvmalloc instead of alloc_percpu
Changes in v4:
- Fixed inconsistent array size
- Use kvmalloc_array instead of kvmalloc
Signed-off-by: Yidong Ren <yidren@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-07-30
this is a pull request of one patch for net/master.
The patch by Anton Vasilyev and the Linux Driver Verification project
fixes a memory leak in the ems_usb driver's disconnect function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"A paravirt UP-patching fix, and an I2C MUX driver lockdep warning fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock/x86: Use LOCK_PREFIX in __pv_queued_spin_unlock() assembly code
i2c/mux, locking/core: Annotate the nested rt_mutex usage
locking/rtmutex: Allow specifying a subclass for nested locking
|
|
The Extended Page Access is a 16-bit register, so change the page
parameter of vsc85xx_phy_page_set to a u16.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When loading module manually, after call xenbus_switch_state to initializes
the state of the netfront device, the driver state did not change so fast
that may lead no dev created in latest kernel. This patch adds wait to make
sure xenbus knows the driver is not in closed/unknown state.
Current state:
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
With the patch installed.
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
Signed-off-by: Xiao Liang <xiliang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no in-tree callers of cn23xx_dump_iq_regs.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use 11M as tx rate for CCK protection control frames
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Introduce mac80211 rts threshold handler in order to add frame
protection support to mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Set MFP_CAPABLE bit in hw flag capabilities exported by the driver
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fall back to software encryption for hw unsupported ciphers in order
to enable 802.11w
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Kernel panic when with high memory pressure, calltrace looks like,
PID: 21439 TASK: ffff881be3afedd0 CPU: 16 COMMAND: "java"
#0 [ffff881ec7ed7630] machine_kexec at ffffffff81059beb
#1 [ffff881ec7ed7690] __crash_kexec at ffffffff81105942
#2 [ffff881ec7ed7760] crash_kexec at ffffffff81105a30
#3 [ffff881ec7ed7778] oops_end at ffffffff816902c8
#4 [ffff881ec7ed77a0] no_context at ffffffff8167ff46
#5 [ffff881ec7ed77f0] __bad_area_nosemaphore at ffffffff8167ffdc
#6 [ffff881ec7ed7838] __node_set at ffffffff81680300
#7 [ffff881ec7ed7860] __do_page_fault at ffffffff8169320f
#8 [ffff881ec7ed78c0] do_page_fault at ffffffff816932b5
#9 [ffff881ec7ed78f0] page_fault at ffffffff8168f4c8
[exception RIP: _raw_spin_lock_irqsave+47]
RIP: ffffffff8168edef RSP: ffff881ec7ed79a8 RFLAGS: 00010046
RAX: 0000000000000246 RBX: ffffea0019740d00 RCX: ffff881ec7ed7fd8
RDX: 0000000000020000 RSI: 0000000000000016 RDI: 0000000000000008
RBP: ffff881ec7ed79a8 R8: 0000000000000246 R9: 000000000001a098
R10: ffff88107ffda000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000008 R14: ffff881ec7ed7a80 R15: ffff881be3afedd0
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
It happens in the pagefault and results in double pagefault
during compacting pages when memory allocation fails.
Analysed the vmcore, the page leads to second pagefault is corrupted
with _mapcount=-256, but private=0.
It's caused by the race between migration and ballooning, and lock
missing in virtballoon_migratepage() of virtio_balloon driver.
This patch fix the bug.
Fixes: e22504296d4f64f ("virtio_balloon: introduce migration primitives to balloon pages")
Cc: stable@vger.kernel.org
Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Huang Chong <huang.chong@zte.com.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The VSP uses a lock to protect the BRU and BRS assignment when
configuring pipelines. The lock is taken in vsp1_du_atomic_begin() and
released in vsp1_du_atomic_flush(), as well as taken and released in
vsp1_du_setup_lif(). This guards against multiple pipelines trying to
assign the same BRU and BRS at the same time.
The DRM framework calls the .atomic_begin() operations in a loop over
all CRTCs included in an atomic commit. On a VSPDL (the only VSP type
where this matters), a single VSP instance handles two CRTCs, with a
single lock. This results in a deadlock when the .atomic_begin()
operation is called on the second CRTC.
The DRM framework serializes atomic commits that affect the same CRTCs,
but doesn't know about two CRTCs sharing the same VSPDL. Two commits
affecting the VSPDL LIF0 and LIF1 respectively can thus race each other,
hence the need for a lock.
This could be fixed on the DRM side by forcing serialization of commits
affecting CRTCs backed by the same VSPDL, but that would negatively
affect performances, as the locking is only needed when the BRU and BRS
need to be reassigned, which is an uncommon case.
The lock protects the whole .atomic_begin() to .atomic_flush() sequence.
The only operation that can occur in-between is vsp1_du_atomic_update(),
which doesn't touch the BRU and BRS, and thus doesn't need to be
protected by the lock. We can thus only take the lock around the
pipeline setup calls in vsp1_du_atomic_flush(), which fixes the
deadlock.
Fixes: f81f9adc4ee1 ("media: v4l: vsp1: Assign BRU and BRS to pipelines dynamically")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The repeat period is read from a static array. If a keydown event is
reported from bpf with a high protocol number, we read out of bounds. This
is unlikely to end up with a reasonable repeat period at the best of times,
in which case no timely key up event is generated.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
ems_usb_probe() allocates memory for dev->tx_msg_buffer, but there
is no its deallocation in ems_usb_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There are no in-tree callers of qed_get_cm_pq_idx_rl since it be there,
so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since driver is devicetree-based, all device type and charateristic can be
determined by the compatible string and its data. It's unnecessary to
create another dependent function to check chip ID and then decide whether
the specific funciton is being supported on a certain device. It can be
totally replaced by the existing flag, so a cleanup is made by removing
the function and the only user, HWLRO.
MT2701 also have a missing HWLRO support in old code, so add it the same
patch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve more in the existing code by reusing dma_zalloc_coherent instead
of dma_alloc_coherent with __GFP_ZERO or superfluous zeroing buffer.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-27 (Vxlan updates)
This series from Gal and Saeed provides updates to mlx5 vxlan implementation.
Gal, started with three cleanups to reflect the actual hardware vxlan state
- reflect 4789 UDP port default addition to software database
- check maximum number of vxlan UDP ports
- cleanup an unused member in vxlan work
Then Gal provides performance optimization by replacing the
vxlan radix tree with a hash table.
Measuring mlx5e_vxlan_lookup_port execution time:
Radix Tree Hash Table
--------------- ------------ ------------
Single Stream 161 ns 79 ns (51% improvement)
Multi Stream 259 ns 136 ns (47% improvement)
Measuring UDP stream packet rate, single fully utilized TX core:
Radix Tree: 498,300 PPS
Hash Table: 555,468 PPS (11% improvement)
Next, from Saeed, vxlan refactoring to allow sharing the vxlan table
between different mlx5 netdevice instances like PF and VF representors,
this is done by making mlx5 vxlan interface more generic and decoupling
it from PF netdevice structures and logic, then moving it into mlx5 core
as a low level interface so it can be used by VF representors, which is
illustrated in the last patch of the serious.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing MTU, RTNL is held so use rtnl_dereference
instead of rcu_dereference.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Seems it was missed while adding for first net dev in dual-emac mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for today STMMAC_ALIGN macro (which is used to align DMA stuff)
relies on L1 line length (L1_CACHE_BYTES).
This isn't correct in case of system with several cache levels
which might have L1 cache line length smaller than L2 line. This
can lead to sharing one cache line between DMA buffer and other
data, so we can lose this data while invalidate DMA buffer before
DMA transaction.
Fix that by using SMP_CACHE_BYTES instead of L1_CACHE_BYTES for
aligning.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2018-01-16
this is a pull request for net-next/master consisting of 38 patches.
Dan Murphy's patch fixes the path to a file in the comment of the CAN
Error Message Frame Mask structure.
A patch by Colin Ian King fixes a typo in the cc770 driver.
The next patch is by me an sorts the Kconfigand Makefile entries of the
CAN-USB driver subdir alphabetically.
The patch by Jakob Unterwurzacher adds support for the UCAN USB-CAN
adapter.
YueHaibing's patch replaces a open coded skb_put()+memset() by
skb_put_zero() in the CAN-dev infrastructure.
Zhu Yi provides a patch to enable multi-queue CAN devices.
Three patches by Luc Van Oostenryck fix the return value of several
driver's xmit function, I contribute a patch for the a fourth driver.
Fabio Estevam's patch switches the flexcan driver to SPDX identifier.
Two patches by Jia-Ju Bai replace the mdelay() by a usleep_range() in
the sja1000 drivers.
The next 6 patches are by Anssi Hannula and refactor the xilinx CAN
driver and add support for the xilinx CAN FD core.
A patch by Gustavo A. R. Silva adds fallthrough annotation to the
peak_usb driver.
5 patches by Stephane Grosjean for the peak CANFD driver do some
cleanups and provide more improvements for further firmware releases.
The remaining 13 patches are by Jimmy Assarsson and the first clean up
the kvaser_usb driver, so that the later patches add support for the
Kvaser USB hydra family.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no in-tree callers of qed_set_gft_event_id_cm_hdr.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no in-tree callers.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous change in the AML parser code blindly set all non-successful
dispatcher statuses to AE_OK. That approach is incorrect, though,
because successful control method invocations from module-level
return AE_CTRL_TRANSFER. Overwriting AE_OK to this status causes the
AML parser to think that there was no return value from the control
method invocation.
Fixes: 92c0f4af386 (ACPICA: AML Parser: ignore dispatcher error status during table load)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
