| Age | Commit message (Collapse) | Author |
|---|
|
The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.
This patch was tested on Raspberry Pi 3B+
Link: https://github.com/raspberrypi/linux/issues/2608
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a new rx packet arrives, the rx path will decide whether to reuse
the remainder of the page or not according to one of the below conditions:
1. frag_info->frag_stride == PAGE_SIZE / 2
2. frags->page_offset + frag_info->frag_size > PAGE_SIZE;
The first condition is no met for when XDP is set.
For XDP, page_offset is always set to priv->rx_headroom which is
XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some
padding, still the 2nd release condition will hold since
XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not
be released and will be _wrongly_ reused for next free rx descriptor.
In XDP there is an assumption to have a page per packet and reuse can
break such assumption and might cause packet data corruptions.
Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd
case to avoid page reuse when XDP is set, since rx_headroom is set to 0
for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup.
No additional cache line is required for the new condition.
Fixes: 34db548bfb95 ("mlx4: add page recycling in receive path")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Suggested-by: Martin KaFai Lau <kafai@fb.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expose counters ASIC has in the group of RFC 2819 counters that count
number of packets within specific size range.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configuring SLI_PKTn_OUTPUT_CONTROL, VF driver was assuming that IPTR
mode was disabled by reset, which was not true. Since DPDK driver had
set IPTR mode previously, the VF driver (which uses buf-ptr-only mode) was
not properly handling DROQ packets (i.e. it saw zero-length packets).
This represented an invalid hardware configuration which the driver could
not handle.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.
Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3ffe64f1a641 ("hv_netvsc: split sub-channel setup into async and sync")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Octeon Ethernet drivers work perfectly without PCI.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tag type in the frame extraction header is only a bit wide. There's
no need to use GENMASK when retrieving the information. This patch
simplify the code by dropping GENMASK and using BIT instead.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were returning DUPLEX_UNKNOWN in get_link_ksettings() when
the link was down. Unfortunately, this causes a problem when
"ethtool -s autoneg on" is issued for a link which is down because
the ethtool code first reads the settings and then reapplies them
with only the changes provided on the command line. Which results
in us diving into set_link_ksettings() with DUPLEX_UNKNOWN which is
not DUPLEX_FULL, so set_link_ksettings() throws an -EINVAL error.
do not return DUPLEX_UNKNOWN to fix the issue.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch remove the following documentation warning
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:103: warning: Excess function parameter 'priv' description in 'stmmac_axi_setup'
It was introduced in commit afea03656add7 ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix a typo in the word Describe
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On XDP_TX we need to free up the frame only when tun_xdp_tx() returns a
negative value. A positive value indicates that the packet is
successfully enqueued to the ptr_ring, so freeing the page causes
use-after-free.
Fixes: 735fc4054b3a ("xdp: change ndo_xdp_xmit API to support bulking")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hwrm_dbg_resp_addr and hwrm_dbg_resp_dma_addr are never used
and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the existing %pad printk format to print dma_addr_t values.
This avoids the following warnings when compiling on the parisc platform:
warning: format '%llx' expects argument of type 'long long unsigned int', but argument 2 has type 'dma_addr_t {aka unsigned int}' [-Wformat=]
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing entry for RTL8211C to mdio_device_id table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: cf87915cb9f8 ("net: phy: realtek: add support for RTL8211C")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the swap macro and remove unnecessary variable *temp*.
This makes the code easier to read and maintain. Also, slightly
refactor some code due to the removal of *temp*.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some network drivers include functionality to speed down the PHY when
suspending and just waiting for a WoL packet because this saves energy.
This functionality is quite generic, therefore let's factor it out to
phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This functionality will also be needed in subsequent patches of this
series, therefore factor it out to a helper.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Actually, hclge_get_ring_chain_from_mbx is used to get ring type, tqp id,
and int_gl index from mailbox message. So the comments is incorrect. This
patch fixes it.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HCLGE_INT_GL_IDX_M and HCLGE_INT_GL_IDX_S are used to set fireware
cmd. When getting int_gl value from mailbox message, we should use
HNAE3_RING_GL_IDX_M and HNAE3_RING_GL_IDX_S.
Fixes: 79eee4108541 ("net: hns3: add int_gl_idx setup for VF")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
handle->reset_level is assigned to HNAE3_NONE_RESET when client is
initialized, if a tx timeout happens right after initialization,
then handle->reset_level is not resetted to HNAE3_FUNC_RESET in
hclge_reset_event, which will cause reset event not properly
handled problem.
This patch fixes it by setting handle->reset_level properly when
client is initialized.
Fixes: 6d4c3981a8d8 ("net: hns3: Changes to make enet watchdog timeout func common for PF/VF")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The configuration of the ring will be used to reinitialize the
ring after the hardware reset is completed. So we should not
release and reacquire this configuration during reset.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing reset, netdev has not been brought up is not an error,
it means that we do not need do the stop operation, so just return
zero.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to hardware's description, driver should get reset event
from VECTOR0_PF_OTHER_INT_ST(0x20800) instead of
VECTOR0_PF_OTHER_INT_SRC(0x20700).
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Netdevice reset should not be requested frequently, a new one
must wait a moment since there may be some work not completed.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since current locking was not covering certain code where
netdev was being accessed or manipulated, this patch fixes
it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to hardware's description, the head pointer register should
be written before the tail pointer register while doing command queue
initialization.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- A slew of driver fixes for Mediatek mt7622
- Fix a direction inversion bug in the Ingenic driver
- Fix unsupported drive strength setting on the PFC r8a77970
- Off by one and NULL dereference fixes in the NSP driver
* tag 'pinctrl-v4.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: nsp: Fix potential NULL dereference
pinctrl: nsp: off by ones in nsp_pinmux_enable()
pinctrl: sh-pfc: r8a77970: remove SH_PFC_PIN_CFG_DRIVE_STRENGTH flag
pinctrl: ingenic: Fix inverted direction for < JZ4770
pinctrl: mt7622: fix a kernel panic when gpio-hog is being applied
pinctrl: mt7622: stop using the deprecated pinctrl_add_gpio_range
pinctrl: mt7622: fix that pinctrl_claim_hogs cannot work
pinctrl: mt7622: fix initialization sequence between eint and gpiochip
pinctrl: mt7622: fix error path on failing at groups building
|
|
Pull drm fixes from Dave Airlie:
- two AGP fixes in here
- a bunch of mostly amdgpu fixes
- sun4i build fix
- two armada fixes
- some tegra fixes
- one i915 core and one i915 gvt fix
* tag 'drm-fixes-2018-07-16-1' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu/pp/smu7: use a local variable for toc indexing
amd/dc/dce100: On dce100, set clocks to 0 on suspend
drm/amd/display: Convert 10kHz clks from PPLib into kHz for Vega
drm/amdgpu: Verify root PD is mapped into kernel address space (v4)
drm/amd/display: fix invalid function table override
drm/amdgpu: Reserve VM root shared fence slot for command submission (v3)
Revert "drm/amd/display: Don't return ddc result and read_bytes in same return value"
char: amd64-agp: Use 64-bit arithmetic instead of 32-bit
char: agp: Change return type to vm_fault_t
drm/i915: Fix hotplug irq ack on i965/g4x
drm/armada: fix irq handling
drm/armada: fix colorkey mode property
drm/tegra: Fix comparison operator for buffer size
gpu: host1x: Check whether size of unpin isn't 0
gpu: host1x: Skip IOMMU initialization if firewall is enabled
drm/sun4i: link in front-end code if needed
drm/i915/gvt: update vreg on inhibit context lri command
|
|
If the server or network is misbehaving and we get an unexpected reply
we can sometimes miss the request not being started and wait on a
request and never get a response, or even double complete the same
request. Fix this by replacing the send_complete completion with just a
per command lock. Add a per command cookie as well so that we can know
if we're getting a double completion for a previous event. Also check
to make sure we dont have REQUEUED set as that means we raced with the
timeout handler and need to just let the retry occur.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We can race with the snd timeout and the per-request timeout and end up
requeuing the same request twice. We can't use the send_complete
completion to tell if everything is ok because we hold the tx_lock
during send, so the timeout stuff will block waiting to mark the socket
dead, and we could be marked complete and still requeue. Instead add a
flag to the socket so we know whether we've been requeued yet.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When the CSI is receiving from a bt.656 bus, include a check for
field type 'alternate' when determining whether to set CSI clock
mode to CCIR656_INTERLACED or CCIR656_PROGRESSIVE.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
If the second LVDS channel has been disabled in the DT when using dual-channel
mode we should not print a warning.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The LVDS signal integrity is only guaranteed when the correct enable
sequence (first IPU DI, then LDB) is used. If the LDB display output was
active before the imx-drm driver is loaded (like when a bootsplash was
active) the DI will be disabled by the full IPU reset we do when loading
the driver. The LDB control registers are not part of the IPU range and
thus will remain unchanged.
This leads to the LDB still being active when the DI is getting enabled,
effectively reversing the required enable sequence. Fix this by also
disabling the LDB on driver bind.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
A comment in the review of the patch adding the phandle cache said that
the cache would have to be updated when modules are applied and removed.
This patch implements the cache updates.
Fixes: 0b3ce78e90fc ("of: cache phandle nodes to reduce cost of of_find_node_by_phandle()")
Reported-by: Alan Tull <atull@kernel.org>
Suggested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
drm_legacy_ctxbitmap_next() returns idr_alloc() which can return
-ENOMEM, -EINVAL or -ENOSPC none of which are -1 . but the call sites
of drm_legacy_ctxbitmap_next() seem to be assuming that the error case
would be -1 (original return of drm_ctxbitmap_next() prior to 2.6.23
was actually -1). Thus reenable error handling by checking for < 0.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 62968144e673 ("drm: convert drm context code to use Linux idr")
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1531571532-22733-1-git-send-email-hofrat@osadl.org
|
|
Add ELAN0622 to ACPI mapping table to support Elan touchpad found in
Ideapad 330-15AST.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Reported-by: Anant Shende <anantshende@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.18-rc
*) Fix to get xhci working after disable<->enable cycle
*) Fix wrong enum used for status lines (also fixes a compilation
warning).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Looks like the adjusted syntax wasn't fully build tested. This fixes
failures with powerpc builds:
drivers/mmc/host/mxcmmc.c: In function ‘mxcmci_swap_buffers’:
drivers/mmc/host/mxcmmc.c:296:51: error: expected ‘)’ before ‘;’ token
void *buf = kmap_atomic(sg_page(sg) + sg->offset;
^
drivers/mmc/host/mxcmmc.c:299:1: error: expected ‘,’ or ‘;’ before ‘}’ token
}
^
Fixes: b189e7589f6d3 ("mmc: mxcmmc: handle highmem pages")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If softsynthx_read() is called with `count < 3`, `count - 3` wraps, causing
the loop to copy as much data as available to the provided buffer. If
softsynthx_read() is invoked through sys_splice(), this causes an
unbounded kernel write; but even when userspace just reads from it
normally, a small size could cause userspace crashes.
Fixes: 425e586cf95b ("speakup: add unicode variant of /dev/softsynth")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'hostif_mib_set_request_bool'
'hostif_mib_set_request_bool' function receives a bool as value and
send the received value with MIB_VALUE_TYPE_BOOL type. There is
one case where the value passed is not a boolean one but
'MCAST_FILTER_PROMISC' which is '2'. Call hostif_mib_set_request_int
instead for related multicast enumeration. This changes original
code behaviour but seems to be the right way to do this.
Fixes: 8ce76bff0e6a ("staging: ks7010: add new helpers to achieve mib set request and simplify code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit b83b8b1881c4 ("staging:r8188eu: Use lib80211 to support TKIP")
is causing 2 problems for me:
1) One boot the wifi on a laptop with a r8188eu wifi device would not
connect and dmesg contained an oops about scheduling while atomic
pointing to the tkip code. This went away after reverting the commit.
2) I reverted the revert to try and get the oops from 1. again to be able
to add it to this commit message. But now the system did connect to the
wifi only to print a whole bunch of oopses, followed by a hardfreeze a
few seconds later. Subsequent reboots also all lead to scenario 2. Until
I reverted the commit again.
Revert the commit fixes both issues making the laptop usable again.
Fixes: b83b8b1881c4 ("staging:r8188eu: Use lib80211 to support TKIP")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently nouveau doesn't actually expose the state debugfs file that's
usually provided for any modesetting driver that supports atomic, even
if nouveau is loaded with atomic=1. This is due to the fact that the
standard debugfs files that DRM creates for atomic drivers is called
when drm_get_pci_dev() is called from nouveau_drm.c. This happens well
before we've initialized the display core, which is currently
responsible for setting the DRIVER_ATOMIC cap.
So, move the atomic option into nouveau_drm.c and just add the
DRIVER_ATOMIC cap whenever it's enabled on the kernel commandline. This
shouldn't cause any actual issues, as the atomic ioctl will still fail
as expected even if the display core doesn't disable it until later in
the init sequence. This also provides the added benefit of being able to
use the state debugfs file to check the current display state even if
clients aren't allowed to modify it through anything other than the
legacy ioctls.
Additionally, disable the DRIVER_ATOMIC cap in nv04's display core, as
this was already disabled there previously.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This both uses the legacy modesetting structures in a racy manner, and
additionally also doesn't even check the right variable (enabled != the
CRTC is actually turned on for atomic).
This fixes issues on my P50 regarding the dedicated GPU not entering
runtime suspend.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
A CRTC being enabled doesn't mean it's on! It doesn't even necessarily
mean it's being used. This fixes runtime PM leaks on the P50 I've got
next to me.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
When MST and atomic were introduced to nouveau, another structure that
could contain a drm_connector embedded within it was introduced; struct
nv50_mstc. This meant that we no longer would be able to simply loop
through our connector list and assume that nouveau_connector() would
return a proper pointer for each connector, since the assertion that
all connectors coming from nouveau have a full nouveau_connector struct
became invalid.
Unfortunately, none of the actual code that looped through connectors
ever got updated, which means that we've been causing invalid memory
accesses for quite a while now.
An example that was caught by KASAN:
[ 201.038698] ==================================================================
[ 201.038792] BUG: KASAN: slab-out-of-bounds in nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038797] Read of size 4 at addr ffff88076738c650 by task kworker/0:3/718
[ 201.038800]
[ 201.038822] CPU: 0 PID: 718 Comm: kworker/0:3 Tainted: G O 4.18.0-rc4Lyude-Test+ #1
[ 201.038825] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018
[ 201.038882] Workqueue: events nouveau_display_hpd_work [nouveau]
[ 201.038887] Call Trace:
[ 201.038894] dump_stack+0xa4/0xfd
[ 201.038900] print_address_description+0x71/0x239
[ 201.038929] ? nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038935] kasan_report.cold.6+0x242/0x2fe
[ 201.038942] __asan_report_load4_noabort+0x19/0x20
[ 201.038970] nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038998] ? nvif_notify_put+0x1f0/0x1f0 [nouveau]
[ 201.039003] ? kmsg_dump_rewind_nolock+0xe4/0xe4
[ 201.039049] nouveau_display_init.cold.12+0x34/0x39 [nouveau]
[ 201.039089] ? nouveau_user_framebuffer_create+0x120/0x120 [nouveau]
[ 201.039133] nouveau_display_resume+0x5c0/0x810 [nouveau]
[ 201.039173] ? nvkm_client_ioctl+0x20/0x20 [nouveau]
[ 201.039215] nouveau_do_resume+0x19f/0x570 [nouveau]
[ 201.039256] nouveau_pmops_runtime_resume+0xd8/0x2a0 [nouveau]
[ 201.039264] pci_pm_runtime_resume+0x130/0x250
[ 201.039269] ? pci_restore_standard_config+0x70/0x70
[ 201.039275] __rpm_callback+0x1f2/0x5d0
[ 201.039279] ? rpm_resume+0x560/0x18a0
[ 201.039283] ? pci_restore_standard_config+0x70/0x70
[ 201.039287] ? pci_restore_standard_config+0x70/0x70
[ 201.039291] ? pci_restore_standard_config+0x70/0x70
[ 201.039296] rpm_callback+0x175/0x210
[ 201.039300] ? pci_restore_standard_config+0x70/0x70
[ 201.039305] rpm_resume+0xcc3/0x18a0
[ 201.039312] ? rpm_callback+0x210/0x210
[ 201.039317] ? __pm_runtime_resume+0x9e/0x100
[ 201.039322] ? kasan_check_write+0x14/0x20
[ 201.039326] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039333] __pm_runtime_resume+0xac/0x100
[ 201.039374] nouveau_display_hpd_work+0x67/0x1f0 [nouveau]
[ 201.039380] process_one_work+0x7a0/0x14d0
[ 201.039388] ? cancel_delayed_work_sync+0x20/0x20
[ 201.039392] ? lock_acquire+0x113/0x310
[ 201.039398] ? kasan_check_write+0x14/0x20
[ 201.039402] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039409] worker_thread+0x86/0xb50
[ 201.039418] kthread+0x2e9/0x3a0
[ 201.039422] ? process_one_work+0x14d0/0x14d0
[ 201.039426] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 201.039431] ret_from_fork+0x3a/0x50
[ 201.039441]
[ 201.039444] Allocated by task 79:
[ 201.039449] save_stack+0x43/0xd0
[ 201.039452] kasan_kmalloc+0xc4/0xe0
[ 201.039456] kmem_cache_alloc_trace+0x10a/0x260
[ 201.039494] nv50_mstm_add_connector+0x9a/0x340 [nouveau]
[ 201.039504] drm_dp_add_port+0xff5/0x1fc0 [drm_kms_helper]
[ 201.039511] drm_dp_send_link_address+0x4a7/0x740 [drm_kms_helper]
[ 201.039518] drm_dp_check_and_send_link_address+0x1a7/0x210 [drm_kms_helper]
[ 201.039525] drm_dp_mst_link_probe_work+0x71/0xb0 [drm_kms_helper]
[ 201.039529] process_one_work+0x7a0/0x14d0
[ 201.039533] worker_thread+0x86/0xb50
[ 201.039537] kthread+0x2e9/0x3a0
[ 201.039541] ret_from_fork+0x3a/0x50
[ 201.039543]
[ 201.039546] Freed by task 0:
[ 201.039549] (stack is not available)
[ 201.039551]
[ 201.039555] The buggy address belongs to the object at ffff88076738c1a8
which belongs to the cache kmalloc-2048 of size 2048
[ 201.039559] The buggy address is located 1192 bytes inside of
2048-byte region [ffff88076738c1a8, ffff88076738c9a8)
[ 201.039563] The buggy address belongs to the page:
[ 201.039567] page:ffffea001d9ce200 count:1 mapcount:0 mapping:ffff88084000d0c0 index:0x0 compound_mapcount: 0
[ 201.039573] flags: 0x8000000000008100(slab|head)
[ 201.039578] raw: 8000000000008100 ffffea001da3be08 ffffea001da25a08 ffff88084000d0c0
[ 201.039582] raw: 0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000
[ 201.039585] page dumped because: kasan: bad access detected
[ 201.039588]
[ 201.039591] Memory state around the buggy address:
[ 201.039594] ffff88076738c500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039598] ffff88076738c580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039601] >ffff88076738c600: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
[ 201.039604] ^
[ 201.039607] ffff88076738c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039611] ffff88076738c700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039613] ==================================================================
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Every codepath in nouveau that loops through the connector list
currently does so using the old method, which is prone to race
conditions from MST connectors being created and destroyed. This has
been causing a multitude of problems, including memory corruption from
trying to access connectors that have already been freed!
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The bo array has req->nr_buffers elements so the > should be >= so we
don't read beyond the end of the array.
Fixes: a1606a9596e5 ("drm/nouveau: new gem pushbuf interface, bump to 0.0.16")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
disables
It was possible for this to be skipped when shutting down MST streams, and
leaving the core channel interlocked with a wndw channel update that never
happens - leading to a hung display.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-By: Lyude Paul <lyude@redhat.com>
|
|
The device (a POS terminal) implements CDC ACM, but has not union
descriptor.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
