| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One regression fix causes imx51 board hang when using ULPI PHY
|
|
This patch fixes the byte count indication in CQE for processed IPsec
packets that contain a metadata header.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds common functions to handle mellanox metadata headers.
These functions are used by IPsec and TLS to process FPGA metadata.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables TLS Rx based on available HW capabilities.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds software statistics for TLS to count important
events.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the TLS rx offload data path according to the
requirements of the TLS generic NIC offload infrastructure.
Special metadata ethertype is used to pass information to
the hardware.
When hardware loses synchronization a special resync request
metadata message is used to request resync.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the mlx5 implementation of the TLS Rx routines to add/del TLS
contexts, also add the tls_dev_resync_rx routine
to work with the TLS inline Rx crypto offload infrastructure.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Complete the implementation for Innova TLS (FPGA-based) hardware by
adding support for rx inline crypto offload.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For symmetry, we rename mlx5e_tls_offload_context to
mlx5e_tls_offload_context_tx before we add mlx5e_tls_offload_context_rx.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For symmetry, we rename tls_offload_context to
tls_offload_context_tx before we add tls_offload_context_rx.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The classification operations that are used for RSS make use of several
lookup tables. Having hit counters for these tables is really helpful
to determine what flows were matched by ingress traffic, and see the
path of packets among all the classifier tables.
This commit adds hit counters for the 3 tables used at the moment :
- The decoding table (also called lookup_id table), that links flows
identified by the Header Parser to the flow table.
There's one entry per flow, located at :
.../mvpp2/<controller>/flows/XX/dec_hits
Note that there are 21 flows in the decoding table, whereas there are
52 flows in the Header Parser. That's because there are several kind
of traffic that will match a given flow. Reading the hit counter from
one sub-flow will clear all hit counter that have the same flow_id.
This also applies to the flow_hits.
- The flow table, that contains all the different lookups to be
performed by the classifier for each packet of a given flow. The match
is done on the first entry of the flow sequence.
- The C2 engine entries, that are used to assign the default rx queue,
and enable or disable RSS for a given port.
There's one entry per flow, located at:
.../mvpp2/<controller>/flows/XX/flow_hits
There is one C2 entry per port, so the c2 hit counter is located at :
.../mvpp2/<controller>/ethX/c2_hits
All hit counter values are 16-bits clear-on-read values.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The classifier configuration for RSS is quite complex, with several
lookup tables being used. This commit adds useful info in debugfs to
see how the different tables are configured :
Added 2 new entries in the per-port directory :
- .../eth0/default_rxq : The default rx queue on that port
- .../eth0/rss_enable : Indicates if RSS is enabled in the C2 entry
Added the 'flows' directory :
It contains one entry per sub-flow. a 'sub-flow' is a unique path from
Header Parser to the flow table. Multiple sub-flows can point to the
same 'flow' (each flow has an id from 8 to 29, which is its index in the
Lookup Id table) :
- .../flows/00/...
/01/...
...
/51/id : The flow id. There are 21 unique flows. There's one
flow per combination of the following parameters :
- L4 protocol (TCP, UDP, none)
- L3 protocol (IPv4, IPv6)
- L3 parameters (Fragmented or not)
- L2 parameters (Vlan tag presence or not)
.../type : The flow type. This is an even higher level flow,
that we manipulate with ethtool. It can be :
"udp4" "tcp4" "udp6" "tcp6" "ipv4" "ipv6" "other".
.../eth0/...
.../eth1/engine : The hash generation engine used for this
flow on the given port
.../hash_opts : The hash generation options indicating on
what data we base the hash (vlan tag, src
IP, src port, etc.)
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One helpful feature to help debug the Header Parser TCAM filter in PPv2
is to be able to see if the entries did match something when a packet
comes in. This can be done by using the built-in hit counter for TCAM
entries.
This commit implements reading the counter, and exposing its value on
debugfs for each filter entry.
The counter is a 16-bits clear-on-read value, located at:
.../mvpp2/<controller>/parser/XXX/hits
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell PPv2 Packer Header Parser has a TCAM based filter, that is not
trivial to configure and debug. Being able to dump TCAM entries from
userspace can be really helpful to help development of new features
and debug existing ones.
This commit adds a basic debugfs interface for the PPv2 driver, focusing
on TCAM related features.
<mnt>/mvpp2/ --- f2000000.ethernet
\- f4000000.ethernet --- parser --- 000 ...
| \- 001
| \- ...
| \- 255 --- ai
| \- header_data
| \- lookup_id
| \- sram
| \- valid
\- eth1 ...
\- eth2 --- mac_filter
\- parser_entries
\- vid_filter
There's one directory per PPv2 instance, named after pdev->name to make
sure names are uniques. In each of these directories, there's :
- one directory per interface on the controller, each containing :
- "mac_filter", which lists all filtered addresses for this port
(based on TCAM, not on the kernel's uc / mc lists)
- "parser_entries", which lists the indices of all valid TCAM
entries that have this port in their port map
- "vid_filter", which lists the vids allowed on this port, based on
TCAM
- one "parser" directory (the parser is common to all ports), containing :
- one directory per TCAM entry (256 of them, from 0 to 255), each
containing :
- "ai" : Contains the 1 byte Additional Info field from TCAM, and
- "header_data" : Contains the 8 bytes Header Data extracted from
the packet
- "lookup_id" : Contains the 4 bits LU_ID
- "sram" : contains the raw SRAM data, which is the result of the TCAM
lookup. This readonly at the moment.
- "valid" : Indicates if the entry is valid of not.
All entries are read-only, and everything is output in hex form.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the appropriate SPDX license identifiers and drop the license text.
This patch is only cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
I already pulled the first fix, pull the GVT fixes.
- GVT fix for KBL vGPU hang to update virtual register from LRI.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180713070922.GA19840@intel.com
|
|
into drm-fixes
Two armada fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180713075427.GA16160@rmk-PC.armlinux.org.uk
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc5:
- Single fix for a build error when the driver is builtin,
but the backend is a loadable module.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c596cf5-3f24-070e-74f2-c59bfbaf68fa@linux.intel.com
|
|
git://anongit.freedesktop.org/tegra/linux into drm-fixes
drm/tegra: Fixes for v4.18-rc5
This contains a couple of one- or two-line fixes for various minor
issues in the Tegra driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712070142.15571-1-thierry.reding@gmail.com
|
|
into drm-fixes
A few display and GPUVM fixes for 4.18.
A few more fixes for 4.18. Two display fixes and a fix to avoid a segfault if
the GPU does not power up properly on resume. These are on top of my pull
from earlier this week.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712043820.2877-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix hotplug irq ack on i965/g4x (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710213249.GA16479@intel.com
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-15
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various different arm32 JIT improvements in order to optimize code emission
and make the JIT code itself more robust, from Russell.
2) Support simultaneous driver and offloaded XDP in order to allow for advanced
use-cases where some work is offloaded to the NIC and some to the host. Also
add ability for bpftool to load programs and maps beyond just the cgroup case,
from Jakub.
3) Add BPF JIT support in nfp for multiplication as well as division. For the
latter in particular, it uses the reciprocal algorithm to emulate it, from Jiong.
4) Add BTF pretty print functionality to bpftool in plain and JSON output
format, from Okash.
5) Add build and installation to the BPF helper man page into bpftool, from Quentin.
6) Add a TCP BPF callback for listening sockets which is triggered right after
the socket transitions to TCP_LISTEN state, from Andrey.
7) Add a new cgroup tree command to bpftool which iterates over the whole cgroup
tree and prints all attached programs, from Roman.
8) Improve xdp_redirect_cpu sample to support parsing of double VLAN tagged
packets, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for 4.18:
- an important core fix for RTCs using the core offsetting only one
driver is affected
- a fix for the error path of mrst"
* tag 'rtc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: fix alarm read and set offset
rtc: mrst: fix error code in probe()
|
|
Hosts using a VRRP router send their packets with a destination MAC of
the VRRP router which is of the following form [1]:
IPv4 - 00-00-5E-00-01-{VRID}
IPv6 - 00-00-5E-00-02-{VRID}
Where VRID is the ID of the virtual router. Such packets are directed to
the router block in the ASIC by an FDB entry that was added in the
previous patch.
However, in certain cases it is possible to skip this FDB lookup and
send such packets directly to the router. This is accomplished by adding
these special MAC addresses to the RIF cache. If the cache is hit, the
packet will skip the L2 lookup and ingress the router with the RIF
specified in the cache entry.
1. https://tools.ietf.org/html/rfc5798#section-7.3
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Virtual Router Redundancy Protocol packets are used to communicate the
state of the Master router associated with the virtual router ID (VRID).
These are link-local multicast packets sent with IP protocol 112 that
are trapped in the router block in the ASIC.
Add a trap for these packets and mark the trapped packets to prevent
them from potentially being re-flooded by the bridge driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An IP packet received on a netdev with a macvlan upper whose MAC matches
the packet's destination MAC will be re-injected to the Rx path as if it
was received by the macvlan, and perform an L3 lookup.
Reflect this functionality to the ASIC by programming FDB entries that
will direct MACs of macvlan uppers to the router.
In a similar fashion to router interfaces (RIFs) that are programmed
upon the addition of the first IP address on an interface and destroyed
upon the removal of the last IP address, the FDB entries for the macvlan
are added and destroyed based on the addition of the first and removal
of the last IP address on the macvlan.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to allow more unicast MAC addresses (e.g., VRRP virtual MAC) to
be directed to the router we need to enable macvlan uppers on top of
mlxsw netdevs.
Allow macvlan upper devices on top of mlxsw netdevs and sanitize
configurations that can't work. For example, a macvlan can't be enslaved
to a bridge as without ACLs the device doesn't take the destination MAC
into account when classifying a packet to a bridge instance (i.e., a
FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The > comparisons should be >= or else we read beyond the end of the
pinctrl->functions[] array.
Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The datasheet does not document any registers to control drive strength,
and no drive strength registers are for this reason described for this
SoC. The flags indicating that drive strength can be controlled are
however set for some pins in the driver.
This leads to a NULL pointer dereference when the sh-pfc core tries to
access the struct describing the drive strength registers, for example
when reading the sysfs file pinconf-pins.
Fix this by removing the SH_PFC_PIN_CFG_DRIVE_STRENGTH from all pins.
Fixes: b92ac66a1819602b ("pinctrl: sh-pfc: Add R8A77970 PFC support")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The .gpio_set_direction() callback was setting inverted direction
for SoCs older than the JZ4770, this restores the correct behaviour.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When we are explicitly using GPIO hogging mechanism in the pinctrl node,
such as:
&pio {
line_input {
gpio-hog;
gpios = <95 0>, <96 0>, <97 0>;
input;
};
};
A kernel panic happens at dereferencing a NULL pointer: In this case, the
drvdata is still not setup properly yet when it is being accessed.
A better solution for fixing up this issue should be we should obtain the
private data from struct gpio_chip using a specific gpiochip_get_data
instead of a generic dev_get_drvdata.
[ 0.249424] Unable to handle kernel NULL pointer dereference at virtual
address 000000c8
[ 0.257818] Mem abort info:
[ 0.260704] ESR = 0x96000005
[ 0.263869] Exception class = DABT (current EL), IL = 32 bits
[ 0.270011] SET = 0, FnV = 0
[ 0.273167] EA = 0, S1PTW = 0
[ 0.276421] Data abort info:
[ 0.279398] ISV = 0, ISS = 0x00000005
[ 0.283372] CM = 0, WnR = 0
[ 0.286440] [00000000000000c8] user address but active_mm is swapper
[ 0.293027] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 0.298795] Modules linked in:
[ 0.301958] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.16.0-rc1+ #389
[ 0.308716] Hardware name: MediaTek MT7622 RFB1 board (DT)
[ 0.314396] pstate: 80000005 (Nzcv daif -PAN -UAO)
[ 0.319362] pc : mtk_hw_pin_field_get+0x28/0x118
[ 0.324140] lr : mtk_hw_set_value+0x30/0x104
[ 0.328557] sp : ffffff800801b6d0
[ 0.331983] x29: ffffff800801b6d0 x28: ffffff80086b7970
[ 0.337484] x27: 0000000000000000 x26: ffffff80087b8000
[ 0.342986] x25: 0000000000000000 x24: ffffffc00324c230
[ 0.348487] x23: 0000000000000003 x22: 0000000000000000
[ 0.353988] x21: ffffff80087b8000 x20: 0000000000000000
[ 0.359489] x19: 0000000000000054 x18: 00000000fffff7c0
[ 0.364990] x17: 0000000000006300 x16: 000000000000003f
[ 0.370492] x15: 000000000000000e x14: ffffffffffffffff
[ 0.375993] x13: 0000000000000000 x12: 0000000000000020
[ 0.381494] x11: 0000000000000006 x10: 0101010101010101
[ 0.386995] x9 : fffffffffffffffa x8 : 0000000000000007
[ 0.392496] x7 : ffffff80085d63f8 x6 : 0000000000000003
[ 0.397997] x5 : 0000000000000054 x4 : ffffffc0031eb800
[ 0.403499] x3 : ffffff800801b728 x2 : 0000000000000003
[ 0.409000] x1 : 0000000000000054 x0 : 0000000000000000
[ 0.414502] Process swapper/0 (pid: 1, stack limit = 0x000000002a913c1c)
[ 0.421441] Call trace:
[ 0.423968] mtk_hw_pin_field_get+0x28/0x118
[ 0.428387] mtk_hw_set_value+0x30/0x104
[ 0.432445] mtk_gpio_set+0x20/0x28
[ 0.436052] mtk_gpio_direction_output+0x18/0x30
[ 0.440833] gpiod_direction_output_raw_commit+0x7c/0xa0
[ 0.446333] gpiod_direction_output+0x104/0x114
[ 0.451022] gpiod_configure_flags+0xbc/0xfc
[ 0.455441] gpiod_hog+0x8c/0x140
[ 0.458869] of_gpiochip_add+0x27c/0x2d4
[ 0.462928] gpiochip_add_data_with_key+0x338/0x5f0
[ 0.467976] mtk_pinctrl_probe+0x388/0x400
[ 0.472217] platform_drv_probe+0x58/0xa4
[ 0.476365] driver_probe_device+0x204/0x44c
[ 0.480783] __device_attach_driver+0xac/0x108
[ 0.485384] bus_for_each_drv+0x7c/0xac
[ 0.489352] __device_attach+0xa0/0x144
[ 0.493320] device_initial_probe+0x10/0x18
[ 0.497647] bus_probe_device+0x2c/0x8c
[ 0.501616] device_add+0x2f8/0x540
[ 0.505226] of_device_add+0x3c/0x44
[ 0.508925] of_platform_device_create_pdata+0x80/0xb8
[ 0.514245] of_platform_bus_create+0x290/0x3e8
[ 0.518933] of_platform_populate+0x78/0x100
[ 0.523352] of_platform_default_populate+0x24/0x2c
[ 0.528403] of_platform_default_populate_init+0x94/0xa4
[ 0.533903] do_one_initcall+0x98/0x130
[ 0.537874] kernel_init_freeable+0x13c/0x1d4
[ 0.542385] kernel_init+0x10/0xf8
[ 0.545903] ret_from_fork+0x10/0x18
[ 0.549603] Code: 900020a1 f9400800 911dcc21 1400001f (f9406401)
[ 0.555916] ---[ end trace de8c34787fdad3b3 ]---
[ 0.560722] Kernel panic - not syncing: Attempted to kill init!
exitcode=0x0000000b
[ 0.560722]
[ 0.570188] SMP: stopping secondary CPUs
[ 0.574253] ---[ end Kernel panic - not syncing: Attempted to kill
init! exitcode=0x0000000b
[ 0.574253]
Cc: stable@vger.kernel.org
Fixes: d6ed93551320 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If the pinctrl node has the gpio-ranges property, the range will be added
by the gpio core and doesn't need to be added by the pinctrl driver.
But for keeping backward compatibility, an explicit pinctrl_add_gpio_range
is still needed to be called when there is a missing gpio-ranges in pinctrl
node in old dts files.
Cc: stable@vger.kernel.org
Fixes: d6ed93551320 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
To allow claiming hogs by pinctrl, we cannot enable pinctrl until all
groups and functions are being added done. Also, it's necessary that
the corresponding gpiochip is being added when the pinctrl device is
enabled.
Cc: stable@vger.kernel.org
Fixes: d6ed93551320 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Because gpichip applied in the driver must depend on mtk eint to implement
the input data debouncing and the translation between gpio and irq, it's
better to keep logic consistent with mtk eint being built prior to gpiochip
being added.
Cc: stable@vger.kernel.org
Fixes: e6dabd38d8e7 ("pinctrl: mediatek: add EINT support to MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It should be to return an error code when failing at groups building.
Cc: stable@vger.kernel.org
Fixes: d6ed93551320 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fixes: f9358e12a0af ("net: mvpp2: split ingress traffic into multiple flows")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We accidentally left out the error handling for kstrtoul().
Fixes: a520030e326a ("qlcnic: Implement flash sysfs callback for 83xx adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By a simple extension of of_phy_get_and_connect() drivers
that have a fixed link on e.g. RGMII can support also
fixed links, so in addition to:
ethernet-port {
phy-mode = "rgmii";
phy-handle = <&foo>;
};
This setup with a fixed-link node and no phy-handle will
now also work just fine:
ethernet-port {
phy-mode = "rgmii";
fixed-link {
speed = <1000>;
full-duplex;
pause;
};
};
This is very helpful for connecting random ethernet ports
to e.g. DSA switches that typically reside on fixed links.
The phy-mode is still there as the fixes link in this case
is still an RGMII link.
Tested on the Cortina Gemini driver with the Vitesse DSA
router chip on a fixed 1Gbit link.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"A clocksource driver fix and a revert"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: arm_arch_timer: Set arch_mem_timer cpumask to cpu_possible_mask
Revert "tick: Prefer a lower rating device only if it's CPU local device"
|
|
Pull rdma fixes from Jason Gunthorpe:
"Things have been quite slow, only 6 RC patches have been sent to the
list. Regression, user visible bugs, and crashing fixes:
- cxgb4 could wrongly fail MR creation due to a typo
- various crashes if the wrong QP type is mixed in with APIs that
expect other types
- syzkaller oops
- using ERR_PTR and NULL together cases HFI1 to crash in some cases
- mlx5 memory leak in error unwind"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix memory leak in mlx5_ib_create_srq() error path
RDMA/uverbs: Don't fail in creation of multiple flows
IB/hfi1: Fix incorrect mixing of ERR_PTR and NULL return values
RDMA/uverbs: Fix slab-out-of-bounds in ib_uverbs_ex_create_flow
RDMA/uverbs: Protect from attempts to create flows on unsupported QP
iw_cxgb4: correctly enforce the max reg_mr depth
|
|
Split handling of offloaded and driver programs completely. Since
offloaded programs always come with XDP_FLAGS_HW_MODE set in reality
there could be no sharing, anyway, programs would only be installed
in driver or in hardware. Splitting the handling allows us to install
programs in HW and in driver at the same time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Allow netdevsim to accept driver and offload attachment of XDP
BPF programs at the same time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Split the query of HW-attached program from the software one.
Introduce new .ndo_bpf command to query HW-attached program.
This will allow drivers to install different programs in HW
and SW at the same time. Netlink can now also carry multiple
programs on dump (in which case mode will be set to
XDP_ATTACHED_MULTI and user has to check per-attachment point
attributes, IFLA_XDP_PROG_ID will not be present). We reuse
IFLA_XDP_PROG_ID skb space for second mode, so rtnl_xdp_size()
doesn't need to be updated.
Note that the installation side is still not there, since all
drivers currently reject installing more than one program at
the time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Basic operations drivers perform during xdp setup and query can
be moved to helpers in the core. Encapsulate program and flags
into a structure and add helpers. Note that the structure is
intended as the "main" program information source in the driver.
Most drivers will additionally place the program pointer in their
fast path or ring structures.
The helpers don't have a huge impact now, but they will
decrease the code duplication when programs can be installed
in HW and driver at the same time. Encapsulating the basic
operations in helpers will hopefully also reduce the number
of changes to drivers which adopt them.
Helpers could really be static inline, but they depend on
definition of struct netdev_bpf which means they'd have
to be placed in netdevice.h, an already 4500 line header.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
prog_attached of struct netdev_bpf should have been superseded
by simply setting prog_id long time ago, but we kept it around
to allow offloading drivers to communicate attachment mode (drv
vs hw). Subsequently drivers were also allowed to report back
attachment flags (prog_flags), and since nowadays only programs
attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell
the attachment mode from the flags driver reports. Remove
prog_attached member.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dave Jiang:
- ensure that a variable passed in by reference to acpi_nfit_ctl is
always set to a value. An incremental patch is provided due to notice
from testing in -next. The rest of the commits did not exhibit
issues.
- fix a return path in nsio_rw_bytes() that was not returning "bytes
remain" as expected for the function.
- address an issue where applications polling on scrub-completion for
the NVDIMM may falsely wakeup and read the wrong state value and
cause hang.
- change the test unit persistent capability attribute to fix up a
broken assumption in the unit test infrastructure wrt the
'write_cache' attribute
- ratelimit dev_info() in the dax device check_vma() function since
this is easily triggered from userspace
* tag 'libnvdimm-fixes-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix unchecked dereference in acpi_nfit_ctl
acpi, nfit: Fix scrub idle detection
tools/testing/nvdimm: advertise a write cache for nfit_test
acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value
dev-dax: check_vma: ratelimit dev_info-s
libnvdimm, pmem: Fix memcpy_mcsafe() return code handling in nsio_rw_bytes()
|
|
Rather than using the index variable stored in vram. If
the device fails to come back online after a resume cycle,
reads from vram will return all 1s which will cause a
segfault. Based on a patch from Thomas Martitz <kugel@rockbox.org>.
This avoids the segfault, but we still need to sort out
why the GPU does not come back online after a resume.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=105760
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The offset needs to be added after reading the alarm value.
It also needs to be subtracted after the now < alarm test.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
