| Age | Commit message (Collapse) | Author |
|---|
|
Rather than forcing the platform resources to declare the desired page
size, simply use the existing information passed down to us by the higher
layers. This way we work out of the box with all flash chips that the
kernel knows about.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
When resetting the ECC registers/counters, the bit will automatically
clear itself once the reset has actually finished. So make sure we
wait for that to occur before doing anything else rather than assuming
everything is peachy and proceeding with stale ECC values.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
We used the platform rd_dly field when we meant to use the wr_dly field.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The NAND base may send some controls which are neither CLE nor ALE, so
we need to explicitly check both instead of assuming things are always
one or the other. Otherwise, we sometimes send out illegal addresses
to the NAND device.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Our write_buf/read_buf funcs always do ECC in HW ECC mode. That is not
needed for raw funcs. In fact, write_buf/read_buf should be a pure func
for data input/output while chip->ecc.hwctl controls ECC. Unfortunately,
we can't separate ECC from normal data input/output in our NFC, so our DMA
write_buf/read_buf entries are coupled with ECC operations closely.
Thus we need to provide dedicated read_page_raw/write_page_raw funcs where
we do non-DMA transactions so as to avoid automatic ECC.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The low level NAND driver doesn't care about filesystems, so punt the
local comment indicating otherwise.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Commit 5349ef3127c77075ff70b2014f17ae0fbcaaf199 (drm/fb: fix
FBIOGET/PUT_VSCREENINFO pixel clock handling) changed the logic of
when a pixclock was valid vs invalid.
The atomic kernel mode setting used by the kernel debugger relies upon
the drm_fb_helper_check_var() to always return -EINVAL. Until a
better solution exists, this behavior will be restored.
CC: David Airlie <airlied@linux.ie>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
If the HW compression is left on, the call backs from the HW will
crash the kernel. The only time this code is called is when kernel
mode setting is in use with kgdb and the kdb shell.
The atomic display pipe handler callback will reset everything when
kgdb restores kernel to the run state.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
|
|
Implement atomic kernel mode settings using the fb layer's debug hook
system for supporting debugger interaction.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Implement the callbacks for KDB entry/exit via the drm helpers.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Add fb ops to handle enter/exit of the kernel debugger. If present, the
fb core will register them with KGDB and they'll be called when the
debugger is entered and exited. The new functions are responsible for
switching to an appropriate debug framebuffer and restoring the
interrupted state at exit time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Add the kms keyword processing to kgdboc and the callbacks to invoke
console switching when ever kgdboc is started with "kgdboc=kms,kbd".
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The kernel console interface stores the number of lines it is
configured to use. The kdb debugger can greatly benefit by knowing how
many lines there are on the console for the pager functionality
without having the end user compile in the setting or have to
repeatedly change it at run time.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: Andrew Morton <akpm@linux-foundation.org>
|
|
These functions allow the kernel debugger to save and restore the
state of the system console.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: David Airlie <airlied@linux.ie>
CC: Andrew Morton <akpm@linux-foundation.org>
|
|
FBIO_WAITFORVSYNC is a stardard ioctl for waiting vsync, already
used by some userspace, so add it as an alias for OMAPFB_WAITFORVSYNC.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
The function overlay_manager_store currently fails if the sysfs input is a
prefix string of an existing overlay manager name. This occurs because strncmp
compares the two strings only till the length of the input sysfs string. So a
sysfs input "lcd" will match manager name "lcd2" which is incorrect behavior.
The use of sysfs_streq here will prevent this false positive match to occur.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
In the case of an error on calling dsi_update_screen_l4(), a
successful framedone callback is still sent to panel-taal. An
error should be returned to taal_update() instead.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
TDO35S samples the data on the falling adge of the pixel clock,
therefore the data strobe should be on the raising edge.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
omapfb_mode_to_timings() sets the bpp to 0 when bootarg omapfb.mode is set to
either "pal" or "ntsc". This patch corrects this by setting the bpp to 24, as
would be done if omapdss_default_get_recommended_bpp() would be called.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Move sysfs entry creation to omapfb_probe() from omapfb_create_framebuffers().
This will make sure that sysfs entry is not left behind in case of unsuccessful
probe due to failure in enabling fb0 of omapfb_create_framebuffers().
Signed-off-by: Afzal Mohammed <lazfamam@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Remove extra return statement in omapdss_default_get_recommended_bpp
from overlay.c
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
An overlay in YUV mode has to have an even input width, because data for
each pixel is divided between two adjacent pixels.
The algorithm handling manual update overlay adjusting may adjust the
overlay width to be odd.
This patch adds a check for that situation, and makes the width even.
The width is increased by one if it is possible (the unadjusted input
width is larger than the width), and decreased by one if increasing is
not possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Using bool silently converted input to 0 or 1, making the range check
useless. Use unsigned long instead, and convert to bool later. Found by
Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Unsigned regno can never be less than zero. Found by Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Unsigned rotate can never be less than zero. Found by Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Make sure NULL return value of fb2display() is not referenced. Found by
Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Skip any further processing of taal_enable_te(), taal_rotate(), and
taal_mirror() if value remains unchanged.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
OMAP DSS HW cannot send updates with odd widths. Normally the widths are
made even while preparing the update.
This patch adds a BUG_ON() to check if the update width is even. This is
to detect broken updates cleanly, as otherwise the OMAP DSS HW will just
halt, leading to obscure error situations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
The current FIFO low threshold was too low, and caused the FIFO to run
empty when core domain went to INA state between FIFO fills. This patch
increases the low threshold to keep that from happening.
The threshold values depend quite much on the HW and the use cases, so
this should actually be somehow configurable from board files, perhaps.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
The code presumed that all ComplexIO interrupts are errors. This is not
the case. This patch adds proper error mask for CIO interrupt handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
SMRPS function always sent BTA after sending the SMRPS packet. This is
not needed, and also caused some (buggy) panels to bug. This patch
removes the BTA.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Currently the update area on manual update displays is automatically
enlargened to fully cover scaled overlays. This patch makes that
optional, allowing the panel driver to choose if it's used or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Previously a work was started on FRAMEDONE interrupt, and this work
either sent a BTA synchronously or looped until TE_SIZE was zero, to
wait for the end of the transfer.
This patch changes a BTA to be sent asynchronously from FRAMEDONE
interrupt, and when a BTA interrupt is received, the transfer is
finished. This way we do the whole process asynchronously, and also
inside interrupt context.
This will give us much better latency to handle the end of the frame
than with the previous work based solution.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Change dsi_vc_config_l4/vp() to loop for the VC_BUSY flag to change, and
return an error if it fails.
Busy looping is bad, but there's no interrupt that can be used for all the
cases where VC can be busy. So the caller should first try to make sure
that the VC is not busy, if possible, and then call dsi_vc_config_l4/vp().
Most notable case when the caller cannot be sure if the VC is busy is
after frame has been sent. Usually DSI buffers have been emptied until we
need to reconfig the VC, but in some rare cases the VC can still be busy,
and this patch will handle that case.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Once the DSI PLL is separated from the DSI display a full DSI reset will
not be performed every time the display is enabled so the interface and
VCs must be disabled when disabling the display. If the VCs are not
disabled some register accesses will abort.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
The TRM tells us to wait for the DSI PLL derived clocks to become
active before selecting them for use. I didn't actually have any issues
which this would fix but according to the TRM it seems to be the right
thing to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Print an error message if dsi_calc_clock_rates() fails just like it's
done when dispc_calc_clock_rates() fails.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Do not leave the free running pixel clock enabled if the DSI PLL reset
times out.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
The OCTEON is a MIPS64 based SOC family with an on chip watchdog unit.
The driver is split into two source files one for the C code and one
for assembly. Assembly is needed to handle the NMI and then print the
machine state before the reboot is triggered.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org,
Patchwork: https://patchwork.linux-mips.org/patch/1503/
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/watchdog/octeon-wdt-main.c
create mode 100644 drivers/watchdog/octeon-wdt-nmi.S
|
|
Add support for the battery voltage measurement part of the JZ4740 ADC unit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1416/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add support for reading the ADCIN pin of the ADC unit on JZ4740 SoCs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: lm-sensors@lm-sensors.org
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1425/
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add OHCI glue code for JZ4740 SoCs OHCI module.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1411/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: linux-mmc@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1463/
Patchwork: https://patchwork.linux-mips.org/patch/1523/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add support for the NAND controller on JZ4740 SoCs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1470/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add support for the LCD controller on JZ4740 SoCs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1470/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add support for the RTC unit on JZ4740 SoCs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: rtc-linux@googlegroups.com
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Alessandro Zummo <a.zummo@towertech.it>,
Patchwork: https://patchwork.linux-mips.org/patch/1424/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
au1000_eth uses firmware calls to get a valid MAC address, and changes
it depending on platform device id. This patch moves this logic out of
the driver into the platform device registration part, where boards with
supported chips can use whatever firmware interface they need; the default
implementation maintains compatibility with existing, YAMON-based firmware.
Tested-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1481/
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the SERIAL_8250_AU1X00 config symbol. Instead, use the MIPS_ALCHEMY
one which is always defined when building an Au1x00-based platform.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Linux-serial <linux-serial@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This one depends on a previous patch (which removes SOC_AU1X00 and changes
MACH_ALCHEMY) to apply cleanly (and then actually work), so I'd love for
this to go in via the mips tree.
|
|
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
- release_mem_region
+ release_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
