| Age | Commit message (Collapse) | Author |
|---|
|
The current driver accepts any videomode with pclk < 154MHz. This is not
correct, as with 1 lane and/or 1.62Mbps speed not all videomodes can be
supported.
Add code to reject modes that require more bandwidth that is available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-6-tomi.valkeinen@ti.com
|
|
Initially DP0_SRCCTRL is set to a static value which includes
DP0_SRCCTRL_LANES_2 and DP0_SRCCTRL_BW27, even when only 1 lane of
1.62Gbps speed is used. DP1_SRCCTRL is configured to a magic number.
This patch changes the configuration as follows:
Configure DP0_SRCCTRL by using tc_srcctrl() which provides the correct
value.
DP1_SRCCTRL needs two bits to be set to the same value as DP0_SRCCTRL:
SSCG and BW27. All other bits can be zero.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-5-tomi.valkeinen@ti.com
|
|
PHY_2LANE bit is always set in DP_PHY_CTRL, breaking 1 lane use.
Set PHY_2LANE only when 2 lanes are used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-4-tomi.valkeinen@ti.com
|
|
DP1_SRCCTRL register and PHY_2LANE field did not have matching defines.
Add these.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-3-tomi.valkeinen@ti.com
|
|
tc358767 driver does not set DRM bus_flags, even if it does configures
the polarity settings into its registers. This means that the DPI source
can't configure the polarities correctly.
Add sync flags accordingly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-2-tomi.valkeinen@ti.com
|
|
On arm64 little endian allyesconfig:
drivers/acpi/nfit/intel.c:149:12: warning: unused function 'intel_security_unlock' [-Wunused-function]
static int intel_security_unlock(struct nvdimm *nvdimm,
^
drivers/acpi/nfit/intel.c:230:12: warning: unused function 'intel_security_erase' [-Wunused-function]
static int intel_security_erase(struct nvdimm *nvdimm,
^
drivers/acpi/nfit/intel.c:279:12: warning: unused function 'intel_security_query_overwrite' [-Wunused-function]
static int intel_security_query_overwrite(struct nvdimm *nvdimm)
^
drivers/acpi/nfit/intel.c:316:12: warning: unused function 'intel_security_overwrite' [-Wunused-function]
static int intel_security_overwrite(struct nvdimm *nvdimm,
^
4 warnings generated.
Mark these functions as __maybe_unused because they are only used when
CONFIG_X86 is set.
Fixes: 4c6926a23b76 ("acpi/nfit, libnvdimm: Add unlock of nvdimm support for Intel DIMMs")
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In commit 6bb2a2af8b1b ("drm/i915/gvt: Fix crash after request->hw_context change"),
forgot to handle workload scan path in ELSP handler case which was to
optimize scanning earlier instead of in gvt submission thread, so request
alloc and add was splitting then which is against right process.
This trys to do a partial revert of that commit which still has workload
request alloc helper and make sure shadow state population is handled after
request alloc for target state buffer.
v3: Fix missed workload status setting in request alloc error path
v2: Fix dispatch workload err path that should add request after alloc anyway.
Fixes: 6bb2a2af8b1b ("drm/i915/gvt: Fix crash after request->hw_context change")
Cc: Bin Yang <bin.yang@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Bin Yang <bin.yang@intel.com>
Reviewed-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
scsi_mq_setup_tags(), which is called by scsi_add_host(), calculates the
command size to allocate based on the prot_capabilities. In the isci
driver, scsi_host_set_prot() is called after scsi_add_host() so the command
size gets calculated to be smaller than it needs to be. Eventually,
scsi_mq_init_request() locates the 'prot_sdb' after the command assuming it
was sized correctly and a buffer overrun may occur.
However, seeing blk_mq_alloc_rqs() rounds up to the nearest cache line
size, the mistake can go unnoticed.
The bug was noticed after the struct request size was reduced by commit
9d037ad707ed ("block: remove req->timeout_list")
Which likely reduced the allocated space for the request by an entire cache
line, enough that the overflow could be hit and it caused a panic, on boot,
at:
RIP: 0010:t10_pi_complete+0x77/0x1c0
Call Trace:
<IRQ>
sd_done+0xf5/0x340
scsi_finish_command+0xc3/0x120
blk_done_softirq+0x83/0xb0
__do_softirq+0xa1/0x2e6
irq_exit+0xbc/0xd0
call_function_single_interrupt+0xf/0x20
</IRQ>
sd_done() would call scsi_prot_sg_count() which reads the number of
entities in 'prot_sdb', but seeing 'prot_sdb' is located after the end of
the allocated space it reads a garbage number and erroneously calls
t10_pi_complete().
To prevent this, the calls to scsi_host_set_prot() are moved into
isci_host_alloc() before the call to scsi_add_host(). Out of caution, also
move the similar call to scsi_host_set_guard().
Fixes: 3d2d75254915 ("[SCSI] isci: T10 DIF support")
Link: http://lkml.kernel.org/r/da851333-eadd-163a-8c78-e1f4ec5ec857@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Intel SCU Linux support <intel-linux-scu@intel.com>
Cc: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "Drop thru" and "Fall
Thru" with "fall through" annotations, which is what GCC is expecting to
find.
Also, in some cases a dash is added as a token in order to separate the
"fall through" annotation from the rest of the comment on the same line,
which is what GCC is expecting to find.
Addresses-Coverity-ID: 114979 ("Missing break in switch")
Addresses-Coverity-ID: 114980 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix boolean expression by using logical AND operator '&&' instead of
bitwise operator '&'.
This issue was detected with the help of Coccinelle.
Fixes: 1e46731efd9c ("scsi: smartpqi: check for null device pointers")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The commit 356fd2663cff ("scsi: Set request queue runtime PM status back to
active on resume") fixed up the inconsistent RPM status between request
queue and device. However changing request queue RPM status shall be done
only on successful resume, otherwise status may be still inconsistent as
below,
Request queue: RPM_ACTIVE
Device: RPM_SUSPENDED
This ends up soft lockup because requests can be submitted to underlying
devices but those devices and their required resource are not resumed.
For example,
After above inconsistent status happens, IO request can be submitted to UFS
device driver but required resource (like clock) is not resumed yet thus
lead to warning as below call stack,
WARN_ON(hba->clk_gating.state != CLKS_ON);
ufshcd_queuecommand
scsi_dispatch_cmd
scsi_request_fn
__blk_run_queue
cfq_insert_request
__elv_add_request
blk_flush_plug_list
blk_finish_plug
jbd2_journal_commit_transaction
kjournald2
We may see all behind IO requests hang because of no response from storage
host or device and then soft lockup happens in system. In the end, system
may crash in many ways.
Fixes: 356fd2663cff (scsi: Set request queue runtime PM status back to active on resume)
Cc: stable@vger.kernel.org
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Delete tab aligning a statement with the right hand side of a preceding
assignment rather than the left hand side.
Found with the help of Coccinelle.
[mkp: added space]
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The return code should be check while qla4xxx_copy_from_fwddb_param fails.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This was apparently forgotten in
894169db1 ("scsi: megaraid_sas: Use 63-bit DMA addressing").
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Leo Zhang <nguzcf@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Changing of caching mode via /sys/devices/.../scsi_disk/.../cache_type may
fail if device responds to MODE SENSE command with DPOFUA flag set, and
then checks this flag to be not set on MODE SELECT command.
In this scenario, when trying to change cache_type, write always fails:
# echo "none" >cache_type
bash: echo: write error: Invalid argument
And following appears in dmesg:
[13007.865745] sd 1:0:1:0: [sda] Sense Key : Illegal Request [current]
[13007.865753] sd 1:0:1:0: [sda] Add. Sense: Invalid field in parameter list
From SBC-4 r15, 6.5.1 "Mode pages overview", description of DEVICE-SPECIFIC
PARAMETER field in the mode parameter header:
...
The write protect (WP) bit for mode data sent with a MODE SELECT
command shall be ignored by the device server.
...
The DPOFUA bit is reserved for mode data sent with a MODE SELECT
command.
...
The remaining bits in the DEVICE-SPECIFIC PARAMETER byte are also reserved
and shall be set to zero.
[mkp: shuffled commentary to commit description]
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The function to_acpi_nfit_desc and function to_acpi_desc
do the same things,delete the function to_acpi_nfit_desc,
and keep the inline function to_acpi_desc.
Signed-off-by: Xiaochun Lee <lixc17@lenovo.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The header file "intel.h" is repeated here, So delete one.
Signed-off-by: Xiaochun Lee <lixc17@lenovo.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This patch includes some fixes and cleanup for idle-page writeback.
1. writeback_limit interface
Now writeback_limit interface is rather conusing. For example, once
writeback limit budget is exausted, admin can see 0 from
/sys/block/zramX/writeback_limit which is same semantic with disable
writeback_limit at this moment. IOW, admin cannot tell that zero came
from disable writeback limit or exausted writeback limit.
To make the interface clear, let's sepatate enable of writeback limit to
another knob - /sys/block/zram0/writeback_limit_enable
* before:
while true :
# to re-enable writeback limit once previous one is used up
echo 0 > /sys/block/zram0/writeback_limit
echo $((200<<20)) > /sys/block/zram0/writeback_limit
..
.. # used up the writeback limit budget
* new
# To enable writeback limit, from the beginning, admin should
# enable it.
echo $((200<<20)) > /sys/block/zram0/writeback_limit
echo 1 > /sys/block/zram/0/writeback_limit_enable
while true :
echo $((200<<20)) > /sys/block/zram0/writeback_limit
..
.. # used up the writeback limit budget
It's much strightforward.
2. fix condition check idle/huge writeback mode check
The mode in writeback_store is not bit opeartion any more so no need to
use bit operations. Furthermore, current condition check is broken in
that it does writeback every pages regardless of huge/idle.
3. clean up idle_store
No need to use goto.
[minchan@kernel.org: missed spin_lock_init]
Link: http://lkml.kernel.org/r/20190103001601.GA255139@google.com
Link: http://lkml.kernel.org/r/20181224033529.19450-1-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Suggested-by: John Dias <joaodias@google.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: John Dias <joaodias@google.com>
Cc: Srinivas Paladugu <srnvs@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A recent regression causes a null ptr crash when dumping cm_id resources.
The cma is incorrectly adding all cm_id restrack resources as kernel mode.
Fixes: af8d70375d56 ("RDMA/restrack: Resource-tracker should not use uobject pointers")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This is an ugly one unfortunately. Currently, all DRM drivers supporting
atomic modesetting will save the state that userspace had set before
suspending, then attempt to restore that state on resume. This probably
worked very well at one point, like many other things, until DP MST came
into the picture. While it's easy to restore state on normal display
connectors that were disconnected during suspend regardless of their
state post-resume, this can't really be done with MST because of the
fact that setting up a downstream sink requires performing sideband
transactions between the source and the MST hub, sending out the ACT
packets, etc.
Because of this, there isn't really a guarantee that we can restore the
atomic state we had before suspend once we've resumed. This sucks pretty
bad, but so far I haven't run into any compositors that this actually
causes serious issues with. Most compositors will notice the hotplug we
send afterwards, and then reprobe state.
Since nouveau and i915 also don't fail the suspend/resume process due to
failing to restore the atomic state, let's make amdgpu match this
behavior. Better to resume the GPU properly, then to stop the process
half way because of a potentially unavoidable atomic commit failure.
Eventually, we'll have a real fix for this problem on the DRM level. But
we've got some more important low-hanging fruit to deal with first.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-3-lyude@redhat.com
|
|
drm_dp_mst_topology_mgr_resume() returns whether or not it managed to
find the topology in question after a suspend resume cycle, and the
driver is supposed to check this value and disable MST accordingly if
it's gone-in addition to sending a hotplug in order to notify userspace
that something changed during suspend.
Currently, amdgpu just makes the mistake of ignoring the return code
from drm_dp_mst_topology_mgr_resume() which means that if a topology was
removed in suspend, amdgpu never notices and assumes it's still
connected which leads to all sorts of problems.
So, fix this by actually checking the rc from
drm_dp_mst_topology_mgr_resume(). Also, reformat the rest of the
function while we're at it to fix the over-indenting.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-2-lyude@redhat.com
|
|
When a VLAN is deleted from a bridge port we should not change the PVID
unless the deleted VLAN is the PVID.
Fixes: fe9ccc785de5 ("mlxsw: spectrum_switchdev: Don't batch VLAN operations")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding a VLAN on a port can trigger the offload of a VXLAN tunnel which
is already a member in the VLAN. In case the configuration of the VXLAN
is not supported, the driver would return -EOPNOTSUPP.
This is problematic since bridge code does not interpret this as error,
but rather that it should try to setup the VLAN using the 8021q driver
instead of switchdev.
Fixes: d70e42b22dd4 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers are not supposed to return errors in switchdev commit phase if
they returned OK in prepare phase. Otherwise, a WARNING is emitted.
However, when the offloading of a VXLAN tunnel is triggered by the
addition of a VLAN on a local port, it is not possible to guarantee that
the commit phase will succeed without doing a lot of work.
In these cases, the artificial division between prepare and commit phase
does not make sense, so simply do the work in the prepare phase.
Fixes: d70e42b22dd4 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VXLAN is a loadable module, MLXSW_SPECTRUM must not be built-in:
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:2547: undefined
reference to `vxlan_fdb_find_uc'
Add Kconfig dependency to enforce usable configurations.
Fixes: 1231e04f5bba ("mlxsw: spectrum_switchdev: Add support for VxLAN encapsulation")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure that lag port TX is disabled before mlxsw_sp_port_lag_leave()
is called and prevent from possible EMAD error.
Fixes: 0d65fc13042f ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removal of the mlxsw driver on Spectrum-2 platforms hits an ASSERT_RTNL()
in Spectrum-2 ACL Bloom filter and in ERP removal paths. This happens
because the multicast router implementation in Spectrum-2 relies on ACLs.
Taking the RTNL lock upon driver removal is useless since the driver first
removes its ports and unregisters from notifiers so concurrent writes
cannot happen at that time. The assertions were originally put as a
reminder for future work involving ERP background optimization, but having
these assertions only during addition serves this purpose as well.
Therefore remove the ASSERT_RTNL() in both places related to ERP and Bloom
filter removal.
Fixes: cf7221a4f5a5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When writing to C-TCAM, mlxsw driver uses cregion->ops->entry_insert().
In case of C-TCAM HW insertion error, the opposite action should take
place.
Add error handling case in which the C-TCAM region entry is removed, by
calling cregion->ops->entry_remove().
Fixes: a0a777b9409f ("mlxsw: spectrum_acl: Start using A-TCAM")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This soft dependency works around an issue where sometimes the genphy
driver is used instead of the dedicated PHY driver. The root cause of
the issue isn't clear yet. People reported the unloading/re-loading
module r8169 helps, and also configuring this soft dependency in
the modprobe config files. Important just seems to be that the
realtek module is loaded before r8169.
Once this has been applied preliminary fix 38af4b903210 ("net: phy:
add workaround for issue where PHY driver doesn't bind to the device")
will be removed.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating frame buffer, userspace may request to attach to a
previously allocated GEM object that is smaller than what GPU
requires. Validation must be done to prevent out-of-bound DMA,
otherwise it could be exploited to reveal sensitive data.
This fix is not done in a common code path because individual
driver might have different requirement.
Cc: stable@vger.kernel.org # v4.2+
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Userspace may request pitch alignment that is not supported by GPU.
Some requests 32, but GPU ignores it and uses default 64 when cpp is
4. If GEM object is allocated based on the smaller alignment, GPU
DMA will go out of bound.
Cc: stable@vger.kernel.org # v4.2+
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Since soft min setting is enough. Hard min setting is redundant.
Reported-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Make sure the clock level enforced is within the allowed
ranges.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Since pp_od_clk_voltage device file is for OD related sysfs operations.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It has been noticed that some phys do not have the registers
required by the previous implementation.
To fix this, instead of using phy_read, the required information
is extracted from the phy_device structure.
fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For those ASICs with no overdrive capabilities, the OD support flag
will be reset.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Otherwise it is impossible to use it for something else, as it will break
userspace that puts garbage there.
The same check should be done in other structures, but the fact that
data in reserved fields is ignored is already part of the kernel ABI.
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The below referenced commit adds a test for integer overflow, but in
doing so prevents the unmap ioctl from ever including the last page of
the address space. Subtract one to compare to the last address of the
unmap to avoid the overflow and wrap-around.
Fixes: 71a7d3d78e3c ("vfio/type1: silence integer overflow warning")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1662291
Cc: stable@vger.kernel.org # v4.15+
Reported-by: Pei Zhang <pezhang@redhat.com>
Debugged-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The handle_irq_perbit function loop every bit in hwirq local variable.
handle_irq_perbit(hwirq) {
for_everyt_bit_in(hwirq) {
handle_domain_irq()
->irq_exit()
->invoke_softirq()
->__do_softirq()
->local_irq_enable() // Here will cause new interrupt.
}
}
When new interrupt coming at local_irq_enable, it will finish another
interrupt handler and pull down the interrupt source. But hwirq is the
local variable for handle_irq_perbit(), it can't get new interrupt
controller pending reg status. So we need update hwirq with pending reg
in every loop.
Also change write_relax to writel could prevent stw from fast retire.
When local_irq is enabled, intc regs is really set-in.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Lu Baoquan <lu.baoquan@intellif.com>
|
|
drivers/vfio/pci/vfio_pci_nvlink2.c cannot be compiled for in-tree
building.
CC drivers/vfio/pci/vfio_pci_nvlink2.o
In file included from drivers/vfio/pci/trace.h:102,
from drivers/vfio/pci/vfio_pci_nvlink2.c:29:
./include/trace/define_trace.h:89:42: fatal error: ./trace.h: No such file or directory
#include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
^
compilation terminated.
make[1]: *** [scripts/Makefile.build;277: drivers/vfio/pci/vfio_pci_nvlink2.o] Error 1
To fix the build error, let's tell include/trace/define_trace.h the
location of drivers/vfio/pci/trace.h
Fixes: 7f92891778df ("vfio_pci: Add NVIDIA GV100GL [Tesla V100 SXM2] subdriver")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The ltq_r32() and ltq_w32() macros use the __raw_readl() and
__raw_writel() functions which do not swap the value to little endian.
On the big endian vrx200 SoC the UART is operated in big endian IO mode,
the readl() and write() functions convert the value to little endian
first and then the driver does not work any more on this SoC.
Currently the vrx200 SoC selects the CONFIG_SWAP_IO_SPACE option,
without this option the serial driver would work, but PCI devices do not
work any more.
This patch makes the driver use the __raw_readl() and __raw_writel()
functions which do not swap the endianness. On big endian system it is
assumed that the device should be access in big endian IO mode and on a
little endian system it would be access in little endian mode.
Fixes: 89b8bd2082bb ("serial: lantiq: Use readl/writel instead of ltq_r32/ltq_w32")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Building the driver when GPIOLIB=n is not selected is causing the following
compilation failure:
drivers/pci/controller/dwc/pci-meson.c: In function 'meson_pcie_assert_reset':
drivers/pci/controller/dwc/pci-meson.c:290:2: error: implicit declaration of function 'gpiod_set_value_cansleep'; did you mean 'gpio_set_value_cansleep'? [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(mp->reset_gpio, 0);
^~~~~~~~~~~~~~~~~~~~~~~~
gpio_set_value_cansleep
drivers/pci/controller/dwc/pci-meson.c: In function 'meson_pcie_probe':
drivers/pci/controller/dwc/pci-meson.c:540:19: error: implicit declaration of function 'devm_gpiod_get'; did you mean 'devm_gpio_free'? [-Werror=implicit-function-declaration]
mp->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
^~~~~~~~~~~~~~
devm_gpio_free
drivers/pci/controller/dwc/pci-meson.c:540:48: error: 'GPIOD_OUT_LOW' undeclared (first use in this function); did you mean 'GPIOF_INIT_LOW'?
mp->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
^~~~~~~~~~~~~
GPIOF_INIT_LOW
Add the missing linux/gpio/consumer.h header to fix it.
Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The last few stragglers coccinelle doesn't pick up are on driver
specific header files. Phase those out as well as dma_alloc_coherent()
zeroes out the memory as well now too.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch fixes a memory corruption that occurred in the
qcom-nandc driver since it was converted to nand_scan().
On boot, an affected device will panic from a NPE at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual address 0
| pgd = (ptrval)
| [00000000] *pgd=00000000
| Internal error: Oops: 80000005 [#1] SMP ARM
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| PC is at (null)
| LR is at nand_block_isbad+0x90/0xa4
| pc : [<00000000>] lr : [<c0592240>] psr: 80000013
| sp : cf839d40 ip : 00000000 fp : cfae9e20
| r10: cf815810 r9 : 00000000 r8 : 00000000
| r7 : 00000000 r6 : 00000000 r5 : 00000001 r4 : cf815810
| r3 : 00000000 r2 : cfae9810 r1 : ffffffff r0 : cf815810
| Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| [<c0592240>] (nand_block_isbad) from [<c0580a94>]
| [<c0580a94>] (allocate_partition) from [<c05811e4>]
| [<c05811e4>] (add_mtd_partitions) from [<c0581164>]
| [<c0581164>] (parse_mtd_partitions) from [<c057def4>]
| [<c057def4>] (mtd_device_parse_register) from [<c059d274>]
| [<c059d274>] (qcom_nandc_probe) from [<c0567f00>]
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4. This causes the
sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_block_bad() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch restores the old behavior by reallocating the shared bam
transaction alloc_bam_transaction() after the chip was identified,
but before mtd_device_parse_register() (which is an alias for
mtd_device_register() - see panic) gets called. This fixes the
corruption and the driver is working again.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f18c ("mtd: rawnand: qcom: convert driver to nand_scan()")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
cpuinfo_cur_freq gets current CPU frequency as detected by hardware
while scaling_cur_freq last known CPU frequency. Some platforms may not
allow checking the CPU frequency of an offline CPU or the associated
resources may have been released via cpufreq_exit when the CPU gets
offlined, in which case the policy would have been invalidated already.
If we attempt to get current frequency from the hardware, it may result
in hang or crash.
For example on Juno, I see:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000188
[0000000000000188] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 5 PID: 4202 Comm: cat Not tainted 4.20.0-08251-ga0f2c0318a15-dirty #87
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : scmi_cpufreq_get_rate+0x34/0xb0
lr : scmi_cpufreq_get_rate+0x34/0xb0
Call trace:
scmi_cpufreq_get_rate+0x34/0xb0
__cpufreq_get+0x34/0xc0
show_cpuinfo_cur_freq+0x24/0x78
show+0x40/0x60
sysfs_kf_seq_show+0xc0/0x148
kernfs_seq_show+0x44/0x50
seq_read+0xd4/0x480
kernfs_fop_read+0x15c/0x208
__vfs_read+0x60/0x188
vfs_read+0x94/0x150
ksys_read+0x6c/0xd8
__arm64_sys_read+0x24/0x30
el0_svc_common+0x78/0x100
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
---[ end trace 3d1024e58f77f6b2 ]---
So fix the issue by checking if the policy is invalid early in
__cpufreq_get before attempting to get the current frequency.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Cast get_unaligned_be32(...) to u64 in order to give the compiler
complete information about the proper arithmetic to use and avoid
a potential integer overflow.
Notice that such function call is used in contexts that expect
expressions of type u64 (64 bits, unsigned); and the following
expressions are currently being evaluated using 32-bit
arithmetic:
val = get_unaligned_be32(&power->update_tag) *
occ->powr_sample_time_us;
val = get_unaligned_be32(&power->vdn.update_tag) *
occ->powr_sample_time_us;
Addresses-Coverity-ID: 1442357 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1442476 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1442508 ("Unintentional integer overflow")
Fixes: ff692d80b2e2 ("hwmon (occ): Add sensor types and versions")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Unsafe global rkey is considered dangerous because it exposes memory
registered for all memory in the system. Only users with a QP on the same
PD can use the rkey, and generally those QPs will already know the
value. However, out of caution, do not expose the value to unprivleged
users on the local system. Require CAP_NET_ADMIN instead.
Cc: <stable@vger.kernel.org> # 4.16
Fixes: 29cf1351d450 ("RDMA/nldev: provide detailed PD information")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This driver requires regmap or the compile fails:
drivers/phy/ti/phy-gmii-sel.c:43:27: error: array type has incomplete element type ‘struct reg_field’
const struct reg_field (*regfields)[PHY_GMII_SEL_LAST];
Add it to kconfig.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
