| Age | Commit message (Collapse) | Author |
|---|
|
Intermittent Kernel crash has been observed on probe in
bcm_qspi_mspi_l2_isr() handler when the MSPI spifie interrupt bit
has not been cleared before registering for interrupts.
Fix the driver to move SoC specific custom interrupt handling code
before we register IRQ in probe. Also clear MSPI interrupt status
resgiter prior to registering IRQ handlers.
Fixes: cc20a38612db ("spi: iproc-qspi: Add Broadcom iProc SoCs support")
Signed-off-by: Kamal Dasu <kdasu@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211008203603.40915-3-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm FF-A driver fixes for v5.15
Couple of fixes addressing issues when FFA driver is build as a module.
One adds the device unregistration which was missing and causes issue
when loading the module second time after unloading once. Another one
adds the missing remove callback on the ffa bus which was missing due
to which modules depending on FFA(e.g. OPTEE) will fail to remove the
device and faults next time that module is loaded again.
* tag 'ffa-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_ffa: Fix __ffa_devices_unregister
firmware: arm_ffa: Add missing remove callback to ffa_bus_type
Link: https://lore.kernel.org/r/20211006153231.4061789-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Tested on SD5200T TB3 dock which has Fresco Logic FL1100 USB 3.0 Host
Controller.
Before this patch streaming video from USB cam made mouse and keyboard
connected to the same USB bus unusable. Also video was jerky.
With this patch streaming video doesn't have any effect on other
periferals and video is smooth.
Cc: stable@vger.kernel.org
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to allocate resources before registering the tty device to
avoid having a racing open() and write() fail to enable rx or
dereference a NULL pointer when accessing the uninitialised fifo.
Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver")
Cc: stable@vger.kernel.org # 4.16
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
[ bjorn: rebased to v5.14-rc2 ]
Link: https://github.com/raspberrypi/linux/issues/3060
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
See https://github.com/raspberrypi/linux/issues/3981
Two read-modify-write cycles on ep->ep_state are not guarded by
xhci->lock. Fix these.
Fixes: f5249461b504 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Three driver bugfixes and one leak fix for the core"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mlxcpld: Modify register setting for 400KHz frequency
i2c: mlxcpld: Fix criteria for frequency setting
i2c: mediatek: Add OFFSET_EXT_CONF setting back
i2c: acpi: fix resource leak in reconfiguration device addition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five fixes, all in drivers.
The big change is the UFS task management rework, with lpfc next and
the rest being fairly minor and obvious fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: Fix iscsi_task use after free
scsi: lpfc: Fix memory overwrite during FC-GS I/O abort handling
scsi: elx: efct: Delete stray unlock statement
scsi: ufs: core: Fix task management completion
scsi: acornscsi: Remove scsi_cmd_to_tag() reference
|
|
commit 126285651b7f ("Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net")
accidentally reverted the effect of
commit 1a8024239da ("virtio-net: fix for skb_over_panic inside big mode")
on drivers/net/virtio_net.c
As a result, users of crosvm (which is using large packet mode)
are experiencing crashes with 5.14-rc1 and above that do not
occur with 5.13.
Crash trace:
[ 61.346677] skbuff: skb_over_panic: text:ffffffff881ae2c7 len:3762 put:3762 head:ffff8a5ec8c22000 data:ffff8a5ec8c22010 tail:0xec2 end:0xec0 dev:<NULL>
[ 61.369192] kernel BUG at net/core/skbuff.c:111!
[ 61.372840] invalid opcode: 0000 [#1] SMP PTI
[ 61.374892] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 5.14.0-rc1 linux-v5.14-rc1-for-mesa-ci.tar.bz2 #1
[ 61.376450] Hardware name: ChromiumOS crosvm, BIOS 0
..
[ 61.393635] Call Trace:
[ 61.394127] <IRQ>
[ 61.394488] skb_put.cold+0x10/0x10
[ 61.395095] page_to_skb+0xf7/0x410
[ 61.395689] receive_buf+0x81/0x1660
[ 61.396228] ? netif_receive_skb_list_internal+0x1ad/0x2b0
[ 61.397180] ? napi_gro_flush+0x97/0xe0
[ 61.397896] ? detach_buf_split+0x67/0x120
[ 61.398573] virtnet_poll+0x2cf/0x420
[ 61.399197] __napi_poll+0x25/0x150
[ 61.399764] net_rx_action+0x22f/0x280
[ 61.400394] __do_softirq+0xba/0x257
[ 61.401012] irq_exit_rcu+0x8e/0xb0
[ 61.401618] common_interrupt+0x7b/0xa0
[ 61.402270] </IRQ>
See
https://lore.kernel.org/r/5edaa2b7c2fe4abd0347b8454b2ac032b6694e2c.camel%40collabora.com
for the report.
Apply the original 1a8024239da ("virtio-net: fix for skb_over_panic inside big mode")
again, the original logic still holds:
In virtio-net's large packet mode, there is a hole in the space behind
buf.
hdr_padded_len - hdr_len
We must take this into account when calculating tailroom.
Cc: Greg KH <gregkh@linuxfoundation.org>
Fixes: fb32856b16ad ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom")
Fixes: 126285651b7f ("Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reported-by: Corentin Noël <corentin.noel@collabora.com>
Tested-by: Corentin Noël <corentin.noel@collabora.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case a PHY device was probed thus in the PHY_READY state, but not
configured and with no network device attached yet, we should not be
trying to shut it down because it has been brought back into reset by
phy_device_reset() towards the end of phy_probe() and anyway we have not
configured the PHY yet.
Fixes: e2f016cf7751 ("net: phy: add a shutdown procedure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'rc'.
Eliminate the follow smatch warning:
drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start()
warn: missing error code 'rc'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: d51e4af5c209 ("qed: aRFS infrastructure support")
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver can call card->isac.release() function from an atomic
context.
Fix this by calling this function after releasing the lock.
The following log reveals it:
[ 44.168226 ] BUG: sleeping function called from invalid context at kernel/workqueue.c:3018
[ 44.168941 ] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 5475, name: modprobe
[ 44.169574 ] INFO: lockdep is turned off.
[ 44.169899 ] irq event stamp: 0
[ 44.170160 ] hardirqs last enabled at (0): [<0000000000000000>] 0x0
[ 44.170627 ] hardirqs last disabled at (0): [<ffffffff814209ed>] copy_process+0x132d/0x3e00
[ 44.171240 ] softirqs last enabled at (0): [<ffffffff81420a1a>] copy_process+0x135a/0x3e00
[ 44.171852 ] softirqs last disabled at (0): [<0000000000000000>] 0x0
[ 44.172318 ] Preemption disabled at:
[ 44.172320 ] [<ffffffffa009b0a9>] nj_release+0x69/0x500 [netjet]
[ 44.174441 ] Call Trace:
[ 44.174630 ] dump_stack_lvl+0xa8/0xd1
[ 44.174912 ] dump_stack+0x15/0x17
[ 44.175166 ] ___might_sleep+0x3a2/0x510
[ 44.175459 ] ? nj_release+0x69/0x500 [netjet]
[ 44.175791 ] __might_sleep+0x82/0xe0
[ 44.176063 ] ? start_flush_work+0x20/0x7b0
[ 44.176375 ] start_flush_work+0x33/0x7b0
[ 44.176672 ] ? trace_irq_enable_rcuidle+0x85/0x170
[ 44.177034 ] ? kasan_quarantine_put+0xaa/0x1f0
[ 44.177372 ] ? kasan_quarantine_put+0xaa/0x1f0
[ 44.177711 ] __flush_work+0x11a/0x1a0
[ 44.177991 ] ? flush_work+0x20/0x20
[ 44.178257 ] ? lock_release+0x13c/0x8f0
[ 44.178550 ] ? __kasan_check_write+0x14/0x20
[ 44.178872 ] ? do_raw_spin_lock+0x148/0x360
[ 44.179187 ] ? read_lock_is_recursive+0x20/0x20
[ 44.179530 ] ? __kasan_check_read+0x11/0x20
[ 44.179846 ] ? do_raw_spin_unlock+0x55/0x900
[ 44.180168 ] ? ____kasan_slab_free+0x116/0x140
[ 44.180505 ] ? _raw_spin_unlock_irqrestore+0x41/0x60
[ 44.180878 ] ? skb_queue_purge+0x1a3/0x1c0
[ 44.181189 ] ? kfree+0x13e/0x290
[ 44.181438 ] flush_work+0x17/0x20
[ 44.181695 ] mISDN_freedchannel+0xe8/0x100
[ 44.182006 ] isac_release+0x210/0x260 [mISDNipac]
[ 44.182366 ] nj_release+0xf6/0x500 [netjet]
[ 44.182685 ] nj_remove+0x48/0x70 [netjet]
[ 44.182989 ] pci_device_remove+0xa9/0x250
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bridging, and possibly other upper stack gizmos, adds the
lower device's netdev->dev_addr to its own uc list, and
then requests it be deleted when the upper bridge device is
removed. This delete request also happens with the bridging
vlan_filtering is enabled and then disabled.
Bonding has a similar behavior with the uc list, but since it
also uses set_mac to manage netdev->dev_addr, it doesn't have
the same the failure case.
Because we store our netdev->dev_addr in our uc list, we need
to ignore the delete request from dev_uc_sync so as to not
lose the address and all hope of communicating. Note that
ndo_set_mac_address is expressly changing netdev->dev_addr,
so no limitation is set there.
Fixes: 2a654540be10 ("ionic: Add Rx filter and rx_mode ndo support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix error handling in mana_create_rxq() when
cq->gdma_id >= gc->max_num_cqs.
Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1633698691-31721-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The cmtp_add_connection() would add a cmtp session to a controller
and run a kernel thread to process cmtp.
__module_get(THIS_MODULE);
session->task = kthread_run(cmtp_session, session, "kcmtpd_ctr_%d",
session->num);
During this process, the kernel thread would call detach_capi_ctr()
to detach a register controller. if the controller
was not attached yet, detach_capi_ctr() would
trigger an array-index-out-bounds bug.
[ 46.866069][ T6479] UBSAN: array-index-out-of-bounds in
drivers/isdn/capi/kcapi.c:483:21
[ 46.867196][ T6479] index -1 is out of range for type 'capi_ctr *[32]'
[ 46.867982][ T6479] CPU: 1 PID: 6479 Comm: kcmtpd_ctr_0 Not tainted
5.15.0-rc2+ #8
[ 46.869002][ T6479] Hardware name: QEMU Standard PC (i440FX + PIIX,
1996), BIOS 1.14.0-2 04/01/2014
[ 46.870107][ T6479] Call Trace:
[ 46.870473][ T6479] dump_stack_lvl+0x57/0x7d
[ 46.870974][ T6479] ubsan_epilogue+0x5/0x40
[ 46.871458][ T6479] __ubsan_handle_out_of_bounds.cold+0x43/0x48
[ 46.872135][ T6479] detach_capi_ctr+0x64/0xc0
[ 46.872639][ T6479] cmtp_session+0x5c8/0x5d0
[ 46.873131][ T6479] ? __init_waitqueue_head+0x60/0x60
[ 46.873712][ T6479] ? cmtp_add_msgpart+0x120/0x120
[ 46.874256][ T6479] kthread+0x147/0x170
[ 46.874709][ T6479] ? set_kthread_struct+0x40/0x40
[ 46.875248][ T6479] ret_from_fork+0x1f/0x30
[ 46.875773][ T6479]
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211008065830.305057-1-butterflyhuangxx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix potential memory leak on a error path in eBPF
- Fix handling of zpci device on reserve
* tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix zpci_zdev_put() on reserve
bpf, s390: Fix potential memory leak about jit_data
|
|
Similar to commit 6087175b7991 ("net: dsa: mt7530: use independent VLAN
learning on VLAN-unaware bridges"), software forwarding between an
unoffloaded LAG port (a bonding interface with an unsupported policy)
and a mv88e6xxx user port directly under a bridge is broken.
We adopt the same strategy, which is to make the standalone ports not
find any ATU entry learned on a bridge port.
Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are
as many FIDs as VIDs (4096). The FID is derived from the VID when
possible (the VTU maps a VID to a FID), with a fallback to the port
based default FID value when not (802.1Q Mode is disabled on the port,
or the classified VID isn't present in the VTU).
The mv88e6xxx driver makes the following use of FIDs and VIDs:
- the port's DefaultVID (to which untagged & pvid-tagged packets get
classified) is 0 and is absent from the VTU, so this kind of packets is
processed in FID 0, the default FID assigned by mv88e6xxx_setup_port.
- every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() ->
mv88e6xxx_atu_new() associates a FID with that VID which increases
linearly starting from 1. Like this:
bridge vlan add dev lan0 vid 100 # FID 1
bridge vlan add dev lan1 vid 100 # still FID 1
bridge vlan add dev lan2 vid 1024 # FID 2
The FID allocation made by the driver is sub-optimal for the following
reasons:
(a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too.
A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID
of 0 too. The difference is that the bridged ports may learn ATU
entries, while the standalone port has the requirement that it must
not, and must not find them either. Standalone ports must not use
the same FID as ports belonging to a bridge. All standalone ports
can use the same FID, since the ATU will never have an entry in
that FID.
(b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a
default FID of 0 on all their ports. The FDBs will not be isolated
between these bridges. Every VLAN-unaware bridge must use the same
FID on all its ports, different from the FID of other bridge ports.
(c) Each bridge VLAN uses a unique FID which is useful for Independent
VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges
will result in the same FID being used by mv88e6xxx_atu_new().
The correct behavior is for VLAN 1 in br0 to have a different FID
compared to VLAN 1 in br1.
This patch cannot fix all the above. Traditionally the DSA framework did
not care about this, and the reality is that DSA core involvement is
needed for the aforementioned issues to be solved. The only thing we can
solve here is an issue which does not require API changes, and that is
issue (a), aka use a different FID for standalone ports vs ports under
VLAN-unaware bridges.
The first step is deciding what VID and FID to use for standalone ports,
and what VID and FID for bridged ports. The 0/0 pair for standalone
ports is what they used up till now, let's keep using that. For bridged
ports, there are 2 cases:
- VLAN-aware ports will never end up using the port default FID, because
packets will always be classified to a VID in the VTU or dropped
otherwise. The FID is the one associated with the VID in the VTU.
- On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at
zero (just as in the case of standalone ports), and just change the
port's default FID from 0 to a different number (say 1).
However, Tobias points out that there is one more requirement to cater to:
cross-chip bridging. The Marvell DSA header does not carry the FID in
it, only the VID. So once a packet crosses a DSA link, if it has a VID
of zero it will get classified to the default FID of that cascade port.
Relying on a port default FID for upstream cascade ports results in
contradictions: a default FID of 0 breaks ATU isolation of bridged ports
on the downstream switch, a default FID of 1 breaks standalone ports on
the downstream switch.
So not only must standalone ports have different FIDs compared to
bridged ports, they must also have different DefaultVID values.
IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply
choose 4095 as the DefaultVID of ports belonging to VLAN-unaware
bridges, and VID 4095 maps to FID 1.
For the xmit operation to look up the same ATU database, we need to put
VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges
too. All shared ports are configured to map this VID to the bridging
FID, because they are members of that VLAN in the VTU. Shared ports
don't need to have 802.1QMode enabled in any way, they always parse the
VID from the DSA header, they don't need to look at the 802.1Q header.
We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the
mention that mv88e6xxx_vtu_setup() which was located right below that
call was flushing the VTU so those entries wouldn't be preserved.
So we need to relocate the VTU flushing prior to the port initialization
during ->setup(). Also note that this is why it is safe to assume that
VID 4095 will get associated with FID 1: the user ports haven't been
created, so there is no avenue for the user to create a bridge VLAN
which could otherwise race with the creation of another FID which would
otherwise use up the non-reserved FID value of 1.
[ Currently mv88e6xxx_port_vlan_join() doesn't have the option of
specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ]
mv88e6xxx_port_db_load_purge() is the function to access the ATU for
FDB/MDB entries, and it used to determine the FID to use for
VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid().
But the driver only called mv88e6xxx_port_set_fid() once, during probe,
so no surprises, the port FID was always 0, the call to get_fid() was
redundant. As much as I would have wanted to not touch that code, the
logic is broken when we add a new FID which is not the port-based
default. Now the port-based default FID only corresponds to standalone
ports, and FDB/MDB entries belong to the bridging service. So while in
the future, when the DSA API will support FDB isolation, we will have to
figure out the FID based on the bridge number, for now there's a single
bridging FID, so hardcode that.
Lastly, the tagger needs to check, when it is transmitting a VLAN
untagged skb, whether it is sending it towards a bridged or a standalone
port. When we see it is bridged we assume the bridge is VLAN-unaware.
Not because it cannot be VLAN-aware but:
- if we are transmitting from a VLAN-aware bridge we are likely doing so
using TX forwarding offload. That code path guarantees that skbs have
a vlan hwaccel tag in them, so we would not enter the "else" branch
of the "if (skb->protocol == htons(ETH_P_8021Q))" condition.
- if we are transmitting on behalf of a VLAN-aware bridge but with no TX
forwarding offload (no PVT support, out of space in the PVT, whatever),
we would indeed be transmitting with VLAN 4095 instead of the bridge
device's pvid. However we would be injecting a "From CPU" frame, and
the switch won't learn from that - it only learns from "Forward" frames.
So it is inconsequential for address learning. And VLAN 4095 is
absolutely enough for the frame to exit the switch, since we never
remove that VLAN from any port.
Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VLAN support in mv88e6xxx has a loaded history. Commit 2ea7a679ca2a
("net: dsa: Don't add vlans when vlan filtering is disabled") noticed
some issues with VLAN and decided the best way to deal with them was to
make the DSA core ignore VLANs added by the bridge while VLAN awareness
is turned off. Those issues were never explained, just presented as
"at least one corner case".
That approach had problems of its own, presented by
commit 54a0ed0df496 ("net: dsa: provide an option for drivers to always
receive bridge VLANs") for the DSA core, followed by
commit 1fb74191988f ("net: dsa: mv88e6xxx: fix vlan setup") which
applied ds->configure_vlan_while_not_filtering = true for mv88e6xxx in
particular.
We still don't know what corner case Andrew saw when he wrote
commit 2ea7a679ca2a ("net: dsa: Don't add vlans when vlan filtering is
disabled"), but Tobias now reports that when we use TX forwarding
offload, pinging an external station from the bridge device is broken if
the front-facing DSA user port has flooding turned off. The full
description is in the link below, but for short, when a mv88e6xxx port
is under a VLAN-unaware bridge, it inherits that bridge's pvid.
So packets ingressing a user port will be classified to e.g. VID 1
(assuming that value for the bridge_default_pvid), whereas when
tag_dsa.c xmits towards a user port, it always sends packets using a VID
of 0 if that port is standalone or under a VLAN-unaware bridge - or at
least it did so prior to commit d82f8ab0d874 ("net: dsa: tag_dsa:
offload the bridge forwarding process").
In any case, when there is a conversation between the CPU and a station
connected to a user port, the station's MAC address is learned in VID 1
but the CPU tries to transmit through VID 0. The packets reach the
intended station, but via flooding and not by virtue of matching the
existing ATU entry.
DSA has established (and enforced in other drivers: sja1105, felix,
mt7530) that a VLAN-unaware port should use a private pvid, and not
inherit the one from the bridge. The bridge's pvid should only be
inherited when that bridge is VLAN-aware, so all state transitions need
to be handled. On the other hand, all bridge VLANs should sit in the VTU
starting with the moment when the bridge offloads them via switchdev,
they are just not used.
This solves the problem that Tobias sees because packets ingressing on
VLAN-unaware user ports now get classified to VID 0, which is also the
VID used by tag_dsa.c on xmit.
Fixes: d82f8ab0d874 ("net: dsa: tag_dsa: offload the bridge forwarding process")
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003222312.284175-2-vladimir.oltean@nxp.com/#24491503
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fix two minor issues in the Xen privcmd driver plus a cleanup patch
for that driver
- fix multiple issues related to running as PVH guest and some related
earlyprintk fixes for other Xen guest types
- fix an issue introduced in 5.15 the Xen balloon driver
* tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: fix cancelled balloon action
xen/x86: adjust data placement
x86/PVH: adjust function/data placement
xen/x86: hook up xen_banner() also for PVH
xen/x86: generalize preferred console model from PV to PVH Dom0
xen/x86: make "earlyprintk=xen" work for HVM/PVH DomU
xen/x86: allow "earlyprintk=xen" to work for PV Dom0
xen/x86: make "earlyprintk=xen" work better for PVH Dom0
xen/x86: allow PVH Dom0 without XEN_PV=y
xen/x86: prevent PVH type from getting clobbered
xen/privcmd: drop "pages" parameter from xen_remap_pfn()
xen/privcmd: fix error handling in mmap-resource processing
xen/privcmd: replace kcalloc() by kvcalloc() when allocating empty pages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recent ACPI-related regression in the PCI subsystem that
introduced a NULL pointer dereference possible to trigger from
user space via sysfs on some systems"
* tag 'acpi-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI: ACPI: Check parent pointer in acpi_pci_find_companion()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.15-rc5 that resolve a number of
reported issues:
- gadget driver fixes
- xhci build warning fixes
- build configuration fix
- cdc-acm tty handling fixes
- cdc-wdm fix
- typec fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-acm: fix break reporting
USB: cdc-acm: fix racy tty buffer accesses
usb: gadget: f_uac2: fixed EP-IN wMaxPacketSize
usb: cdc-wdm: Fix check for WWAN
usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle
usb: typec: tcpm: handle SRC_STARTUP state if cc changes
usb: typec: tcpci: don't handle vSafe0V event if it's not enabled
usb: typec: tipd: Remove dependency on "connector" child fwnode
Partially revert "usb: Kconfig: using select for USB_COMMON dependency"
usb: dwc3: gadget: Revert "set gadgets parent to the right controller"
usb: xhci: tegra: mark PM functions as __maybe_unused
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:
- meson-gx: Fix read/write access for dram-access-quirk
- sdhci-of-at91: Fix calibration sequence"
* tag 'mmc-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: meson-gx: do not use memcpy_to/fromio for dram-access-quirk
mmc: sdhci-of-at91: replace while loop with read_poll_timeout
mmc: sdhci-of-at91: wait for calibration done before proceed
|
|
Pull drm fixes from Dave Airlie:
"I've returned from my tropical island retreat, even managed to bring
one of my kids on a dive with some turtles. Thanks to Daniel for doing
last week's work.
Otherwise this is the weekly fixes pull, it's a bit bigger because the
vc4 reverts in your tree caused some problems with fixes in the
drm-misc tree so it got left out last week, so this week has the misc
fixes rebased without the vc4 pieces.
Otherwise it's i915, amdgpu with the usual fixes and a scattering over
other drivers.
I expect things should calm down a bit more next week.
core:
- Kconfig fix for fb_simple vs simpledrm.
i915:
- Fix RKL HDMI audio
- Fix runtime pm imbalance on i915_gem_shrink() error path
- Fix Type-C port access before hw/sw state sync
- Fix VBT backlight struct version/size check
- Fix VT-d async flip on SKL/BXT with plane stretch workaround
amdgpu:
- DCN 3.1 DP alt mode fixes
- S0ix gfxoff fix
- Fix DRM_AMD_DC_SI dependencies
- PCIe DPC handling fix
- DCN 3.1 scaling fix
- Documentation fix
amdkfd:
- Fix potential memory leak
- IOMMUv2 init fixes
vc4 (there were some hdmi fixes but things got reverted, sort it out
later):
- compiler fix
nouveau:
- Cursor fix
- Fix ttm buffer moves for ampere gpu's by adding minimal
acceleration support.
- memory leak fixes
rockchip:
- crtc/clk fixup
panel:
- ili9341 Fix DT bindings indent
- y030xx067a - yellow tint init seq fix
gbefb:
- Fix gbefb when built with COMPILE_TEST"
* tag 'drm-fixes-2021-10-08' of git://anongit.freedesktop.org/drm/drm: (33 commits)
drm/amd/display: Fix detection of 4 lane for DPALT
drm/amd/display: Limit display scaling to up to 4k for DCN 3.1
drm/amd/display: Skip override for preferred link settings during link training
drm/nouveau/debugfs: fix file release memory leak
drm/nouveau/kms/nv50-: fix file release memory leak
drm/nouveau: avoid a use-after-free when BO init fails
DRM: delete DRM IRQ legacy midlayer docs
video: fbdev: gbefb: Only instantiate device when built for IP32
fbdev: simplefb: fix Kconfig dependencies
drm/panel: abt-y030xx067a: yellow tint fix
dt-bindings: panel: ili9341: correct indentation
drm/nouveau/fifo/ga102: initialise chid on return from channel creation
drm/rockchip: Update crtc fixup to account for fractional clk change
drm/nouveau/ga102-: support ttm buffer moves via copy engine
drm/nouveau/kms/tu102-: delay enabling cursor until after assign_windows
drm/sun4i: dw-hdmi: Fix HDMI PHY clock setup
drm/vc4: hdmi: Remove unused struct
drm/kmb: Enable alpha blended second plane
drm/amdgpu: handle the case of pci_channel_io_frozen only in amdgpu_pci_resume
drm/amdgpu: init iommu after amdkfd device init
...
|
|
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some old IPs do not provide the hardware feature register.
On these IPs, this register is read 0x00000000.
In old driver version, this feature was handled but a regression came
with the commit f10a6a3541b4 ("stmmac: rework get_hw_feature function").
Indeed, this commit removes the return value in dma->get_hw_feature().
This return value was used to indicate the validity of retrieved
information and used later on in stmmac_hw_init() to override
priv->plat data if this hardware feature were valid.
This patch restores the return code in ->get_hw_feature() in order
to indicate the hardware feature validity and override priv->plat
data only if this hardware feature is valid.
Fixes: f10a6a3541b4 ("stmmac: rework get_hw_feature function")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In dibusb_read_eeprom_byte(), if dibusb_i2c_msg() fails, val gets
assigned an value that's not properly initialized.
Using kzalloc() in place of kmalloc() for the buffer fixes this issue,
as the val can now be set to 0 in the event dibusb_i2c_msg() fails.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Tested-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
After freed the dev->urb_list, we should set it to NULL as well as set
counter to zero.
Requested-by: Sean Young <sean@mess.org>
Signed-off-by: Nil Yi <teroincn@163.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
mn88443x_cmn_power_on() did not handle possible errors of
clk_prepare_enable() and always finished successfully so that its caller
mn88443x_probe() did not care about failed preparing/enabling of clocks
as well.
Add missed error handling in both mn88443x_cmn_power_on() and
mn88443x_probe(). This required to change the return value of the former
from "void" to "int".
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0f408ce8941f ("media: dvb-frontends: add Socionext MN88443x ISDB-S/T demodulator driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Don't populate the read-only arrays on the stack but instead them
static const. Also makes the object code smaller by 154 bytes:
Before:
text data bss dec hex filename
42949 22424 0 65373 ff5d media/dvb-frontends/mb86a20s.o
After:
text data bss dec hex filename
42731 22488 0 65219 fec3 media/dvb-frontends/mb86a20s.o
(gcc version 11.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
bus_info field had a different value for the media entity and the video
device.
Fixes v4l2-compliance:
v4l2-compliance.cpp(637): media bus_info 'PCI:0000:00:05.0' differs from
V4L2 bus_info 'PCI:viewfinder'
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
For a try_fmt call, the node noes not need to be enabled.
Fixes v4l2-compliance
fail: v4l2-test-formats.cpp(717): Video Output Multiplanar is valid, but
no TRY_FMT was implemented
test VIDIOC_TRY_FMT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The initial format did not have a valid size.
Fixes v4l2-compliance:
fail: v4l2-test-formats.cpp(723): Video Output Multiplanar:
TRY_FMT(G_FMT) != G_FMT
test VIDIOC_TRY_FMT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Move the calculation to an inline function, to it can be used by other
parts of the driver.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If num_planes is different than zero num_planes and sizes must be
checked to support the format.
Fix the following v4l2-compliance error:
Buffer ioctls (Input 0):
fail: v4l2-test-buffers.cpp(717): q.create_bufs(node, 1, &fmt) != EINVAL
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a V4L2 driver for Renesas R-Car Image Signal Processor. The driver
supports the R-Car V3U SoC where the ISP IP sits between the R-Car CSI-2
receiver and VIN and filters the CSI-2 data based on VC/DT and directs
the video stream to different VIN IPs.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The only usage of imgu_subdev_internal_ops is to assign its address to
the internal_ops field in the v4l2_subdev struct, which is a pointer to
const v4l2_subdev_internal_ops. Make it const to allow the compiler to
put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports
usual features like I2C control, CSI-2 for frame data, digital/analog
gain control or test patterns.
This driver supports the 640x480, 1280x720 and 1632x1224 resolution
modes. It supports runtime PM in order not to draw any unnecessary power.
The part is also called YACG4D0C9SHC and a datasheet can be found at
https://product.skhynix.com/products/cis/cis.go
The large sets of partly undocumented register values are for example
found when searching for the hi846_mipi_raw_Sensor.c Android driver.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The sensor orientation is read from the _PLC ACPI buffer and converted to a v4l2
format.
The sensor rotation is read from the SSDB ACPI buffer and converted into
degrees.
Signed-off-by: Fabian Wüthrich <me@fabwu.ch>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
- Get the min buffer count required by FW from source event change
and use the same value to decide actual buffer count and for
buffer size calculation.
- Setup DPB and OPB buffers after session continue incase of
reconfig.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Consider alignment while calculating NUM_MBS.
Co-developed-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Set work route to FW based on num of vpp pipes.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
AON register programming is used to set NOC to low power mode
during V6 power off sequence. However AON register memory map
is not applicable to 1pipe, hence skipping AON register programming.
Co-developed-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Co-developed-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
V6 HW can have vpp pipes as 1 or 4, add num_vpp_pipes
to resource struture to differentiate.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Adds a sm7280 compatible binding to the venus core.
Co-developed-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Enable no tz FW loading and add routine to reset XTSS.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
