| Age | Commit message (Collapse) | Author |
|---|
|
These are constant data.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove prompts to make all pinctrl cores to non-visible symbols and
make sure the target SoCs would be coupled with the corresponding
cores.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove duplicated assignment statement from aspeed_gpio_probe() function.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Without CONFIG_PM_SLEEP, we get annoying warnings about unused functions:
drivers/pinctrl/qcom/pinctrl-msm.c:1082:12: error: 'msm_pinctrl_resume' defined but not used [-Werror=unused-function]
static int msm_pinctrl_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
drivers/pinctrl/qcom/pinctrl-msm.c:1075:12: error: 'msm_pinctrl_suspend' defined but not used [-Werror=unused-function]
static int msm_pinctrl_suspend(struct device *dev)
Mark them as __maybe_unused to shut up the warning and silently drop
the functions without having to add ugly #ifdefs.
Fixes: 977d057ad346 ("pinctrl: msm: Add sleep pinctrl state transitions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be
configured in devicetree using groups = BOOTx or groups = CARDx. This
makes the behavior consistent with other pins inside the same driver as
well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers.
Fixes: 0fefcb6876d0d6 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be
configured in devicetree using groups = BOOTx or groups = CARDx. This
makes the behavior consistent with other pins inside the same driver as
well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers.
Fixes: 6ac730951104a4 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename the existing "gpio" function to "gpio_periphs". This makes it
consistent with the "gpio_aobus" function. Also GXBB and GXL are also
using the "gpio_periphs" naming, so this makes the code here consistent
with other Amlogic pinctrl drivers.
No functional changes since thee "gpio" function is currently not used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename the existing "gpio" function to "gpio_periphs". This makes it
consistent with the "gpio_aobus" function. Also GXBB and GXL are also
using the "gpio_periphs" naming, so this makes the code here consistent
with other Amlogic pinctrl drivers.
No functional changes since thee "gpio" function is currently not used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PIOBU pins do not lose their voltage during Backup/Self-refresh.
This patch adds a simple GPIO controller for them and a
maintainer for the driver.
This driver adds support for using the pins as GPIO
offering the possibility to read/set the voltage.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
dmesg reports that "Your touchpad (PNP: SYN3052 SYN0100 SYN0002 PNP0f13)
says it can support a different bus."
I've tested the offered psmouse.synaptics_intertouch=1 with 4.18.x and
4.19.x and it seems to work well. No problems seen with suspend/resume.
Also, it appears that RMI/SMBus mode is actually required for 3-4 finger
multitouch gestures to work -- otherwise they are not reported at all.
Information from dmesg in both modes:
psmouse serio3: synaptics: Touchpad model: 1, fw: 8.2, id: 0x1e2b1,
caps: 0xf00123/0x840300/0x2e800/0x0, board id: 3139, fw id: 2000742
psmouse serio3: synaptics: Trying to set up SMBus access
rmi4_smbus 6-002c: registering SMbus-connected sensor
rmi4_f01 rmi4-00.fn01: found RMI device,
manufacturer: Synaptics, product: TM3139-001, fw id: 2000742
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch fixes the coding style problem reported
by checkpatch.pl as below:
ERROR: foo* bar should be "foo *bar"
Signed-off-by: Hardik Singh Rathore <hardiksingh.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
* pm-devfreq:
PM / devfreq: add devfreq_suspend/resume() functions
PM / devfreq: add support for suspend/resume of a devfreq device
PM / devfreq: refactor set_target frequency function
* pm-avs:
PM / AVS: SmartReflex: Switch to SPDX Licence ID
PM / AVS: SmartReflex: NULL check before some freeing functions is not needed
PM / AVS: SmartReflex: remove unused function
* pm-tools:
tools/power/x86/intel_pstate_tracer: Fix non root execution for post processing a trace file
tools/power turbostat: consolidate duplicate model numbers
tools/power turbostat: fix goldmont C-state limit decoding
cpupower : Auto-completion for cpupower tool
tools/power turbostat: reduce debug output
tools/power turbosat: fix AMD APIC-id output
|
|
* pm-core:
PM-runtime: Switch autosuspend over to using hrtimers
* pm-qos:
PM / QoS: Change to use DEFINE_SHOW_ATTRIBUTE macro
* pm-domains:
PM / Domains: remove define_genpd_open_function() and define_genpd_debugfs_fops()
* pm-sleep:
PM / sleep: convert to DEFINE_SHOW_ATTRIBUTE
|
|
* pm-opp:
PM / Domains: Propagate performance state updates
PM / Domains: Factorize dev_pm_genpd_set_performance_state()
PM / Domains: Save OPP table pointer in genpd
OPP: Don't return 0 on error from of_get_required_opp_performance_state()
OPP: Add dev_pm_opp_xlate_performance_state() helper
OPP: Improve _find_table_of_opp_np()
PM / Domains: Make genpd performance states orthogonal to the idlestates
OPP: Fix missing debugfs supply directory for OPPs
OPP: Use opp_table->regulators to verify no regulator case
OPP: Remove of_dev_pm_opp_find_required_opp()
OPP: Rename and relocate of_genpd_opp_to_performance_state()
OPP: Configure all required OPPs
OPP: Add dev_pm_opp_{set|put}_genpd_virt_dev() helper
PM / Domains: Add genpd_opp_to_performance_state()
OPP: Populate OPPs from "required-opps" property
OPP: Populate required opp tables from "required-opps" property
OPP: Separate out custom OPP handler specific code
OPP: Identify and mark genpd OPP tables
PM / Domains: Rename genpd virtual devices as virt_dev
|
|
* pm-cpuidle:
cpuidle: Add 'above' and 'below' idle state metrics
cpuidle: big.LITTLE: fix refcount leak
cpuidle: Add cpuidle.governor= command line parameter
cpuidle: poll_state: Disregard disable idle states
Documentation: admin-guide: PM: Add cpuidle document
* pm-cpufreq:
cpufreq: qcom-hw: Add support for QCOM cpufreq HW driver
dt-bindings: cpufreq: Introduce QCOM cpufreq firmware bindings
cpufreq: nforce2: Remove meaningless return
cpufreq: ia64: Remove unused header files
cpufreq: imx6q: save one condition block for normal case of nvmem read
cpufreq: imx6q: remove unused code
cpufreq: pmac64: add of_node_put()
cpufreq: powernv: add of_node_put()
Documentation: intel_pstate: Clarify coordination of P-State limits
cpufreq: intel_pstate: Force HWP min perf before offline
cpufreq: s3c24xx: Change to use DEFINE_SHOW_ATTRIBUTE macro
* pm-cpufreq-sched:
sched/cpufreq: Add the SPDX tags
|
|
* acpi-pci:
ACPI: Make PCI slot detection driver depend on PCI
ACPI/IORT: Stub out ACS functions when CONFIG_PCI is not set
arm64: select ACPI PCI code only when both features are enabled
PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set
ACPICA: Remove PCI bits from ACPICA when CONFIG_PCI is unset
ACPI: Allow CONFIG_PCI to be unset for reboot
ACPI: Move PCI reset to a separate function
|
|
* acpi-tables:
ACPI / tables: Add an ifdef around amlcode and dsdt_amlcode
ACPI / tables: add DSDT AmlCode new declaration name support
ACPI: SPCR: Consider baud rate 0 as preconfigured state
* acpi-soc:
ACPI / LPSS: Ignore acpi_device_fix_up_power() return value
ACPI / APD: Add clock frequency for Hisilicon Hip08 SPI controller
* acpi-apei:
ACPI/APEI: Clear GHES block_status before panic()
ACPI, APEI, EINJ: Change to use DEFINE_SHOW_ATTRIBUTE macro
* acpi-misc:
ACPI: fix acpi_find_child_device() invocation in acpi_preset_companion()
|
|
* acpica:
ACPICA: Update version to 20181213
ACPICA: change coding style to match ACPICA, no functional change
ACPICA: Debug output: Add option to display method/object evaluation
ACPICA: disassembler: disassemble OEMx tables as AML
ACPICA: Add "Windows 2018.2" string in the _OSI support
ACPICA: Expressions in package elements are not supported
ACPICA: Update buffer-to-string conversions
ACPICA: add comments, no functional change
ACPICA: Remove defines that use deprecated flag
ACPICA: Add "Windows 2018" string in the _OSI support
ACPICA: Update version to 20181031
ACPICA: iASL: Enhance error detection
ACPICA: iASL: adding definition and disassembly for TPM2 revision 3
ACPICA: Use %d for signed int print formatting instead of %u
ACPICA: Debugger: refactor to fix unused variable warning
|
|
Add's support to Raspberry Pi's 7" Touch device. Instead of using a
conventional bus all information is copied into a memory mapped area by
RPi's firmware.
Based on the driver found in RPi's kernel repository.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The current implementation of elan_i2c is known to not support those
2 laptops.
A proper fix is to tweak both elantech and elan_i2c to transmit the
correct information from PS/2, which would make a bad candidate for
stable.
So to give us some time for fixing the root of the problem, disable
elan_i2c for the devices we know are not behaving properly.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1803600
Link: https://bugs.archlinux.org/task/59714
Fixes: df077237cf55 Input: elantech - detect new ICs and setup Host Notify for them
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The loop exits with "timeout" set to -1 not to 0.
Fixes: 1158f0f16224 ("Input: add support for Nomadik SKE keypad controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The gpio IP on Armada 370 at offset 0x18180 has neither a clk nor pwm
registers. So there is no need for a clk as the pwm isn't used anyhow.
So only check for the clk in the presence of the pwm registers. This fixes
a failure to probe the gpio driver for the above mentioned gpio device.
Fixes: 757642f9a584 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
spi_read() and spi_write() require DMA-safe memory. When
CONFIG_VMAP_STACK is selected, those functions cannot be used
with buffers on stack.
This patch replaces calls to spi_read() and spi_write() by
spi_write_then_read() which doesn't require DMA-safe buffers.
Fixes: 0c36ec314735 ("gpio: gpio driver for max7301 SPI GPIO expander")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit ec0daae685b2 ("gpio: omap: Add level wakeup handling for omap4
based SoCs") attempted to fix omap4 GPIO wakeup handling as it was
blocking deeper SoC idle states. However this caused a regression for
GPIOs during runtime having over second long latencies for Ethernet
GPIO interrupt as reportedy by Russell King <rmk+kernel@armlinux.org.uk>.
Let's fix this issue by doing a partial revert of the breaking commit.
We still want to keep the quirk handling around as it is also used for
OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER.
The real fix for omap4 GPIO wakeup handling involves fixes for
omap_set_gpio_trigger() and omap_gpio_unmask_irq() and will be posted
separately. And we must keep the wakeup bit enabled during runtime
because of module doing clock autogating with autoidle configured.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Fixes: ec0daae685b2 ("gpio: omap: Add level wakeup handling for omap4
based SoCs")
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 4.21-rc1
Here are the USB-serial updates for 4.21-rc1, including:
- support for mos7840 3-port devices
- improved ftdi baud-rate divisor calculations
- support for a new class of f81534 devices
Included are also various clean ups and some new pl2303 device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
USB: serial: mos7840: remove set but not used variables 'number, serial'
USB: serial: mos7840: add a product ID for the new product
USB: serial: mos7840: clean up register handling
USB: serial: ftdi_sio: use rounding when calculating baud rate divisors
USB: serial: f81534: fix reading old/new IC config
USB: serial: mos7840: remove set but not used variables 'st, data1, iflag'
USB: serial: quatech2: remove set but not used variable 'port_priv'
|
|
Add ethtool private flag 'xdp_tx_mpwqe' to control the feature
from userspace.
Feature is set ON by default, if supported.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support for the HW feature of multi-packet WQE in XDP
xmit flow.
The conventional TX descriptor (WQE, Work Queue Element) serves
a single packet. Our HW has support for multi-packet WQE (MPWQE)
in which a single descriptor serves multiple TX packets.
This reduces both the PCI overhead and the CPU cycles wasted on
writing them.
In this patch we add support for the HW feature, which is supported
starting from ConnectX-5.
Performance:
Tested packet rate for UDP 64Byte multi-stream over ConnectX-5 NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
XDP_TX:
We see a huge gain on single port ConnectX-5, and reach the 100 Mpps
milestone.
* Single-port HCA:
Before: 70 Mpps
After: 100 Mpps (+42.8%)
* Dual-port HCA:
Before: 51.7 Mpps
After: 57.3 Mpps (+10.8%)
* In both cases we tested traffic on one port and for now On Dual-port HCAs
we see only small gain, we are working to overcome this bottleneck, but
for the moment only with experimental firmware on dual port HCAs we can
reach the wanted numbers as seen on Single-port HCAs.
XDP_REDIRECT:
Redirect from (A) ConnectX-5 to (B) ConnectX-5.
Due to a setup limitation, (A) and (B) are on different NUMA nodes,
so absolute performance numbers are not optimal.
Note:
Below is the transmit rate of (B), not the redirect rate of (A)
which is in some cases higher.
* (B) is single-port:
Before: 77 Mpps
After: 90 Mpps (+16.8%)
* (B) is dual-port:
Before: 61 Mpps
After: 72 Mpps (+18%)
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Each xdp_wqe_info instance describes the number of data-segments
and WQEBBs of the WQE.
This is useful for a downstream patch that adds support for
Multi-Packet TX WQE feature.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This provides infrastructure to have multiple xdp_info instances
for the same consumer index.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Instead of calculating the control segment to be used upon an
XDP xmit doorbell, save it in SQ structure.
Nullify when no pending doorbell.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Do not ignore the CQE opcode.
This helps expose issues and debug them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Do not maintain an SQ state bit to indicate whether an
XDP SQ serves redirect operations.
Instead, rely on the fact that such an XDP SQ doesn't reside
in an RQ instance, while the others do.
This info is not known to the XDP SQ functions themselves,
and they rely on their callers to distinguish between the cases.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
program check
At the end of the RQ polling loop, some XDP-related operations
might be required. Before checking them one by one, check if
an XDP program is even loaded.
Combine all the checks and operations in a single function in xdp files.
This saves unnecessary checks for non-XDP flows.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The opcode indicates about the error reason.
Printing it helps in debug.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
POWER9 Witherspoon machines come with 4 or 6 V100 GPUs which are not
pluggable PCIe devices but still have PCIe links which are used
for config space and MMIO. In addition to that the GPUs have 6 NVLinks
which are connected to other GPUs and the POWER9 CPU. POWER9 chips
have a special unit on a die called an NPU which is an NVLink2 host bus
adapter with p2p connections to 2 to 3 GPUs, 3 or 2 NVLinks to each.
These systems also support ATS (address translation services) which is
a part of the NVLink2 protocol. Such GPUs also share on-board RAM
(16GB or 32GB) to the system via the same NVLink2 so a CPU has
cache-coherent access to a GPU RAM.
This exports GPU RAM to the userspace as a new VFIO device region. This
preregisters the new memory as device memory as it might be used for DMA.
This inserts pfns from the fault handler as the GPU memory is not onlined
until the vendor driver is loaded and trained the NVLinks so doing this
earlier causes low level errors which we fence in the firmware so
it does not hurt the host system but still better be avoided; for the same
reason this does not map GPU RAM into the host kernel (usual thing for
emulated access otherwise).
This exports an ATSD (Address Translation Shootdown) register of NPU which
allows TLB invalidations inside GPU for an operating system. The register
conveniently occupies a single 64k page. It is also presented to
the userspace as a new VFIO device region. One NPU has 8 ATSD registers,
each of them can be used for TLB invalidation in a GPU linked to this NPU.
This allocates one ATSD register per an NVLink bridge allowing passing
up to 6 registers. Due to the host firmware bug (just recently fixed),
only 1 ATSD register per NPU was actually advertised to the host system
so this passes that alone register via the first NVLink bridge device in
the group which is still enough as QEMU collects them all back and
presents to the guest via vPHB to mimic the emulated NPU PHB on the host.
In order to provide the userspace with the information about GPU-to-NVLink
connections, this exports an additional capability called "tgt"
(which is an abbreviated host system bus address). The "tgt" property
tells the GPU its own system address and allows the guest driver to
conglomerate the routing information so each GPU knows how to get directly
to the other GPUs.
For ATS to work, the nest MMU (an NVIDIA block in a P9 CPU) needs to
know LPID (a logical partition ID or a KVM guest hardware ID in other
words) and PID (a memory context ID of a userspace process, not to be
confused with a linux pid). This assigns a GPU to LPID in the NPU and
this is why this adds a listener for KVM on an IOMMU group. A PID comes
via NVLink from a GPU and NPU uses a PID wildcard to pass it through.
This requires coherent memory and ATSD to be available on the host as
the GPU vendor only supports configurations with both features enabled
and other configurations are known not to work. Because of this and
because of the ways the features are advertised to the host system
(which is a device tree with very platform specific properties),
this requires enabled POWERNV platform.
The V100 GPUs do not advertise any of these capabilities via the config
space and there are more than just one device ID so this relies on
the platform to tell whether these GPUs have special abilities such as
NVLinks.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
VFIO regions already support region capabilities with a limited set of
fields. However the subdriver might have to report to the userspace
additional bits.
This adds an add_capability() hook to vfio_pci_regops.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
So far we only allowed mapping of MMIO BARs to the userspace. However
there are GPUs with on-board coherent RAM accessible via side
channels which we also want to map to the userspace. The first client
for this is NVIDIA V100 GPU with NVLink2 direct links to a POWER9
NPU-enabled CPU; such GPUs have 16GB RAM which is coherently mapped
to the system address space, we are going to export these as an extra
PCI region.
We already support extra PCI regions and this adds support for mapping
them to the userspace.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This new memory does not have page structs as it is not plugged to
the host so gup() will fail anyway.
This adds 2 helpers:
- mm_iommu_newdev() to preregister the "memory device" memory so
the rest of API can still be used;
- mm_iommu_is_devmem() to know if the physical address is one of thise
new regions which we must avoid unpinning of.
This adds @mm to tce_page_is_contained() and iommu_tce_xchg() to test
if the memory is device memory to avoid pfn_to_page().
This adds a check for device memory in mm_iommu_ua_mark_dirty_rm() which
does delayed pages dirtying.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Normally mm_iommu_get() should add a reference and mm_iommu_put() should
remove it. However historically mm_iommu_find() does the referencing and
mm_iommu_get() is doing allocation and referencing.
We are going to add another helper to preregister device memory so
instead of having mm_iommu_new() (which pre-registers the normal memory
and references the region), we need separate helpers for pre-registering
and referencing.
This renames:
- mm_iommu_get to mm_iommu_new;
- mm_iommu_find to mm_iommu_get.
This changes mm_iommu_get() to reference the region so the name now
reflects what it does.
This removes the check for exact match from mm_iommu_new() as we want it
to fail on existing regions; mm_iommu_get() should be used instead.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The destroy_workqueue on error unwind is missing, and the code jumps to
the wrong exit label.
Fixes: 813e90b1aeaa ("IB/mlx5: Add advise_mr() support")
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/infiniband/hw/mlx4/qp.c: In function '_mlx4_ib_destroy_qp':
drivers/infiniband/hw/mlx4/qp.c:1612:22: warning:
variable 'pd' set but not used [-Wunused-but-set-variable]
Fixes: e00b64f7c54c ("RDMA: Cleanup undesired pd->uobject usage")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The AFU Descriptor Template in the PCI config space has a Name Space
field which is a 24 Byte ASCII character string of descriptive name
space for the AFU. The OCXL driver read the string four characters at
a time with pci_read_config_dword().
This optimization is valid on a little-endian system since this is PCI,
but a big-endian system ends up with each subset of four characters in
reverse order.
This could be fixed by switching to read characters one by one. Another
option is to swap the bytes if we're big-endian.
Go for the latter with le32_to_cpu().
Cc: stable@vger.kernel.org # v4.16
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We now use dev_name(&ib_device->dev) instead of ib_device->name in iwpm
messages. The name field in struct device is a const char *, where as
ib_device->name is a char array of size IB_DEVICE_NAME_MAX, and it is
pre-initialized to zeros.
Since iw_cm_map() was using memcpy() to copy in the device name, and
copying IWPM_DEVNAME_SIZE bytes, it ends up copying past the end of the
source device name string and copying random bytes. This results in iwpmd
failing the REGISTER_PID request from iwcm. Thus port mapping is broken.
Validate the device and if names, and use strncpy() to inialize the entire
message field.
Fixes: 896de0090a85 ("RDMA/core: Use dev_name instead of ibdev->name")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Virtio-net devices negotiate LRO support with the host.
Display the initially negotiated state with ethtool -k.
Also allow configuring it with ethtool -K, reusing the existing
virtnet_set_guest_offloads helper that configures LRO for XDP.
This is conditional on VIRTIO_NET_F_CTRL_GUEST_OFFLOADS.
Virtio-net negotiates TSO4 and TSO6 separately, but ethtool does not
distinguish between the two. Display LRO as on only if any offload
is active.
RTNL is held while calling virtnet_set_features, same as on the path
from virtnet_xdp_set.
Changes v1 -> v2
- allow ethtool config (-K) only if VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
- show LRO as enabled if any LRO variant is enabled
- do not allow configuration while XDP is active
- differentiate current features from the capable set, to restore
on XDP down only those features that were active on XDP up
- move test out of VIRTIO_NET_F_CSUM/TSO branch, which is tx only
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-21
The following pull-request contains BPF updates for your *net-next* tree.
There is a merge conflict in test_verifier.c. Result looks as follows:
[...]
},
{
"calls: cross frame pruning",
.insns = {
[...]
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "function calls to other bpf functions are allowed for root only",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
{
"jset: functional",
.insns = {
[...]
{
"jset: unknown const compare not taken",
.insns = {
BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0,
BPF_FUNC_get_prandom_u32),
BPF_JMP_IMM(BPF_JSET, BPF_REG_0, 1, 1),
BPF_LDX_MEM(BPF_B, BPF_REG_8, BPF_REG_9, 0),
BPF_EXIT_INSN(),
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "!read_ok",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
[...]
{
"jset: range",
.insns = {
[...]
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.result_unpriv = ACCEPT,
.result = ACCEPT,
},
The main changes are:
1) Various BTF related improvements in order to get line info
working. Meaning, verifier will now annotate the corresponding
BPF C code to the error log, from Martin and Yonghong.
2) Implement support for raw BPF tracepoints in modules, from Matt.
3) Add several improvements to verifier state logic, namely speeding
up stacksafe check, optimizations for stack state equivalence
test and safety checks for liveness analysis, from Alexei.
4) Teach verifier to make use of BPF_JSET instruction, add several
test cases to kselftests and remove nfp specific JSET optimization
now that verifier has awareness, from Jakub.
5) Improve BPF verifier's slot_type marking logic in order to
allow more stack slot sharing, from Jiong.
6) Add sk_msg->size member for context access and add set of fixes
and improvements to make sock_map with kTLS usable with openssl
based applications, from John.
7) Several cleanups and documentation updates in bpftool as well as
auto-mount of tracefs for "bpftool prog tracelog" command,
from Quentin.
8) Include sub-program tags from now on in bpf_prog_info in order to
have a reliable way for user space to get all tags of the program
e.g. needed for kallsyms correlation, from Song.
9) Add BTF annotations for cgroup_local_storage BPF maps and
implement bpf fs pretty print support, from Roman.
10) Fix bpftool in order to allow for cross-compilation, from Ivan.
11) Update of bpftool license to GPLv2-only + BSD-2-Clause in order
to be compatible with libbfd and allow for Debian packaging,
from Jakub.
12) Remove an obsolete prog->aux sanitation in dump and get rid of
version check for prog load, from Daniel.
13) Fix a memory leak in libbpf's line info handling, from Prashant.
14) Fix cpumap's frame alignment for build_skb() so that skb_shared_info
does not get unaligned, from Jesper.
15) Fix test_progs kselftest to work with older compilers which are less
smart in optimizing (and thus throwing build error), from Stanislav.
16) Cleanup and simplify AF_XDP socket teardown, from Björn.
17) Fix sk lookup in BPF kselftest's test_sock_addr with regards
to netns_id argument, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, a dash is added as a token in order
to separate the "Fall through" annotation from the rest of the comment on
the same line, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, a dash is added as a token in order
to separate the "Fall through" annotations from the rest of the comment on
the same line, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, a dash is added as a token in order
to separate the "fall through" annotations from the rest of the comment on
the same line, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
