| Age | Commit message (Collapse) | Author |
|---|
|
Due to hardware errata in Aero controllers, reads to certain fusion
registers could intermittently return zero. This behavior is
transient in nature and subsequent reads will return valid value.
For Aero controllers, any calls to readl to read from certain
registers will be retried for maximum three times, if read returns
zero.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of the register address, pass the instance pointer to clear_intr
and read_fw_status_reg functions. This is done in preparation for adding
adapter type based checks in these functions in later patches of this
series.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Identify all Aero controller PCI IDs with new adapter type.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation for the new Aero series adapter type, all the places where
we check adapter type for Ventura series needs to include any later adapter
types.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
With commit 09c2f95ad404 ("scsi: mpt3sas: Swap I/O memory read value back
to cpu endianness"), 64bit writes in _base_writeq() were rewritten to use
__raw_writeq() instad of writeq().
This introduced a bug apparent on powerpc64 systems such as the Raptor
Talos II that causes the HBA to drop from the PCIe bus under heavy load and
being reinitialized after a couple of seconds.
It can easily be triggered on affacted systems by using something like
fio --name=random-write --iodepth=4 --rw=randwrite --bs=4k --direct=0 \
--size=128M --numjobs=64 --end_fsync=1
fio --name=random-write --iodepth=4 --rw=randwrite --bs=64k --direct=0 \
--size=128M --numjobs=64 --end_fsync=1
a couple of times. In my case I tested it on both a ZFS raidz2 and a btrfs
raid6 using LSI 9300-8i and 9400-8i controllers.
The fix consists in resembling the write ordering of writeq() by adding a
mandatory write memory barrier before device access and a compiler barrier
afterwards. The additional MMIO barrier is superfluous.
Signed-off-by: Stephan Günther <moepi@moepi.net>
Reported-by: Matt Corallo <linux@bluematt.me>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The intent of invoking configfs_depend_item in commit 7474f52a82d51
("tcm_qla2xxx: Perform configfs depend/undepend for base_tpg")
was to prevent a physical Fibre Channel port removal when
virtual (NPIV) ports announced through that physical port are active.
The change does not work as expected: it makes enabled physical port
dependent on target configfs subsystem (the port's parent), something
the configfs guarantees anyway.
Besides, scheduling work in a worker thread and waiting for the work's
completion is not really a valid workaround for the requirement not to call
configfs_depend_item from a configfs callback: the call occasionally
deadlocks.
Thus, removing configfs_depend_item calls does not break anything and fixes
the deadlock problem.
Signed-off-by: Anatoliy Glagolev <glagolig@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The 6320 family of switches uses the same watchdog registers as the
6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvpp2_phylink_validate() sets all modes that are supported by a
given PPv2 port. An mistake made the 10000baseT_Full mode being
advertised in some cases when a port wasn't configured to perform at
10G. This patch fixes this.
Fixes: d97c9f4ab000 ("net: mvpp2: 1000baseX support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. remove fine-tune property and related setting to simplify
the timing adjustment flow.
2. set timing value according to the value from device tree,
and will not care whether PHY insert internal delay.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC Reset was noticed to erase important EEPROM settings.
It is also unnecessary since a chip wide reset was done earlier
in initialization, and that reset preserves EEPROM settings.
There for this patch removes the unnecessary MAC specific reset.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increasing the depth of control path command queue to 8K entries to handle
burst of commands. This feature needs support from FW and the driver/fw
compatibility is checked from the interface version number.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Get HWRM interface major, minor, build and patch version from FW for
checking the FW/Driver compatibility.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Acquiring the rtnl lock while holding usdev_lock could result in a
deadlock.
For example:
usnic_ib_query_port()
| mutex_lock(&us_ibdev->usdev_lock)
| ib_get_eth_speed()
| rtnl_lock()
rtnl_lock()
| usnic_ib_netdevice_event()
| mutex_lock(&us_ibdev->usdev_lock)
This commit moves the usdev_lock acquisition after the rtnl lock has been
released.
This is safe to do because usdev_lock is not protecting anything being
accessed in ib_get_eth_speed(). Hence, the correct order of holding locks
(rtnl -> usdev_lock) is not violated.
Signed-off-by: Parvi Kaustubhi <pkaustub@cisco.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
When in a sleepable (non-atomic) context, wait for firmware completion
instead of polling for it.
Signed-off-by: Gal Pressman <galpress@amazon.com>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
When in a sleepable (non-atomic) context, wait for firmware completion
instead of polling for it.
Signed-off-by: Gal Pressman <galpress@amazon.com>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Introduce a 'flags' field to destroy address handle callback and add a
flag that marks whether the callback is executed in an atomic context or
not.
This will allow drivers to wait for completion instead of polling for it
when it is allowed.
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Fixes: 'commit d588cf8f618d ("target: Fix se_tpg_tfo->tf_subsys regression + remove tf_subsystem")'
'commit cbbd26b8b1a6 ("[iov_iter] new primitives - copy_from_iter_full() and friends")'
Signed-off-by: Yan Wang <wangyan122@huawei.com>
Reviewed-by: Jun Piao <piaojun@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
VIRTIO_PCI_CONFIG() is deprecated. Use VIRTIO_PCI_CONFIG_OFF() instead.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Now that there are no more data path users of vhost_vsock_lock, it can
be turned into a mutex. It's only used by .release() and in the
.ioctl() path.
Depends-on: <20181105103547.22018-1-stefanha@redhat.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
In commit 88c85538, "virtio-blk: add discard and write zeroes features
to specification" (https://github.com/oasis-tcs/virtio-spec), the virtio
block specification has been extended to add VIRTIO_BLK_T_DISCARD and
VIRTIO_BLK_T_WRITE_ZEROES commands. This patch enables support for
discard and write zeroes in the virtio-blk driver when the device
advertises the corresponding features, VIRTIO_BLK_F_DISCARD and
VIRTIO_BLK_F_WRITE_ZEROES.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Introduce a 'flags' field to create address handle callback and add a flag
that marks whether the callback is executed in an atomic context or not.
This will allow drivers to wait for completion instead of polling for it
when it is allowed.
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
mlx5 driver falsely advertises support of software timestamping.
Fix it by removing the false indication.
Fixes: ef9814deafd0 ("net/mlx5e: Add HW timestamping (TS) support")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expression terminated with "," instead of ";", resulted in
set_fte getting bad value for modify_enable_mask field.
Fixes: bd5251dbf156 ("net/mlx5_core: Introduce flow steering destination of type counter")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the completion queue of the RQ is empty, do not immediately return.
If left-over decompressed CQEs (from the previous cycle) were processed,
need to go to the finalization part of the poll function.
Bug exists only when CQE compression is turned ON.
This solves the following issue:
mlx5_core 0000:82:00.1: mlx5_eq_int:544:(pid 0): CQ error on CQN 0xc08, syndrome 0x1
mlx5_core 0000:82:00.1 p4p2: mlx5e_cq_error_event: cqn=0x000c08 event=0x04
Fixes: 4b7dfc992514 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Previous patches tried to make RIF deletion more robust and avoid
use-after-free situations.
As another precaution, hold a reference on a RIF's netdev and release it
when the RIF is deleted.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the past we had multiple instances where RIFs were not properly
deleted.
One of the reasons for leaking a RIF was that at the time when IP
addresses were flushed from the respective netdev (prompting the
destruction of the RIF), the netdev was no longer a mlxsw upper. This
caused the inet{,6}addr notification blocks to ignore the NETDEV_DOWN
event and leak the RIF.
Instead of checking whether the netdev is our upper when an IP address
is removed, we can instead check if the netdev has a RIF configured.
To look up a RIF we need to access mlxsw private data, so the patch
stores the notification blocks inside a mlxsw struct. This then allows
us to use container_of() and extract the required private data.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Next patch is going to make RIF deletion more robust by removing
reliance on fragile mlxsw_sp_lower_get(). This is because a netdev is
not necessarily our upper anymore when its IP addresses are flushed.
The inet{,6}addr notification blocks are going to resolve 'struct
mlxsw_sp' using container_of(), but the functions they call still use
mlxsw_sp_lower_get().
As a preparation for the next patch, propagate 'struct mlxsw_sp' down to
the functions called from the notification blocks and remove reliance on
mlxsw_sp_lower_get().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a LAG device or a VLAN device on top of it is enslaved to a bridge,
the driver propagates the CHANGEUPPER event to the LAG's slaves.
This causes each physical port to increase the reference count of the
internal representation of the bridge port by calling
mlxsw_sp_port_bridge_join().
However, when a port is removed from a LAG, the corresponding leave()
function is not called and the reference count is not decremented. This
leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that
try to understand if the bridge port should be destroyed even when its
reference count is not 0.
Instead, make sure that when a port is unlinked from a LAG it would see
the same events as if the LAG (or its uppers) were unlinked from a
bridge.
The above is achieved by walking the LAG's uppers when a port is
unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is
enslaved to a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b3529af6bb0d ("spectrum: Reference count VLAN entries") started
reference counting port-VLAN entries in a similar fashion to the 8021q
driver.
However, this is not actually needed and only complicates things.
Instead, the driver should forbid the creation of a VLAN on a port if
this VLAN already exists. This would also solve the issue fixed by the
mentioned commit.
Therefore, remove the get()/put() API and use create()/destroy()
instead.
One place that needs special attention is VLAN addition in a VLAN-aware
bridge via switchdev operations. In case the VLAN flags (e.g., 'pvid')
are toggled, then the VLAN entry already exists. To prevent the driver
from wrongly returning EEXIST, the driver is changed to check in the
prepare phase whether the entry already exists and only returns an error
in case it is not associated with the correct bridge port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 993107fea5ee ("mlxsw: spectrum_switchdev: Fix VLAN device
deletion via ioctl") I fixed a bug caused by the fact that the driver
views differently the deletion of a VLAN device when it is deleted via
an ioctl and netlink.
Instead of relying on a specific order of events (device being
unregistered vs. VLAN filter being updated), simply make sure that the
driver performs the necessary cleanup when the VLAN device is unlinked,
which always happens before the other two events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is no longer used. Remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when a RIF is constructed on top of a FID, the RIF increments
the FID's reference count and the RIF is destroyed when the FID's
reference count drops to 1. This effectively means that when no local
ports are member in the FID, the FID is destroyed regardless if the
router port is a member in the FID or not.
The above can lead to the unexpected behavior in which routes using a
VLAN interface as their nexthop device are no longer offloaded after the
last local port leaves the corresponding VLAN (FID).
Example:
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1 offload
# bridge vlan del vid 10 dev swp3
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1
After the patch, the route is offloaded before and after the VLAN is
removed from local port 'swp3', as the RIF corresponding to 'br0.10'
continues to exists.
In order to remove RIFs' reliance on the underlying FID's reference
count, we need to add a reference count to sub-port RIFs, which are RIFs
that correspond to physical ports and their uppers (e.g., LAG devices).
In this case, each {Port, VID} ('struct mlxsw_sp_port_vlan') needs to
hold a reference on the RIF. For example:
bond0.10
|
bond0
|
+-------+
| |
swp1 swp2
Both {Port 1, VID 10} and {Port 2, VID 10} will hold a reference on the
RIF corresponding to 'bond0.10'. When the last reference is dropped, the
RIF will be destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, only VRF and macvlan uppers are supported on top of VLAN
device configured over a bridge, so make sure the driver forbids other
uppers.
Note that enslavement to a VRF is handled earlier in the notification
block, so there is no need to check for a VRF upper here.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify allocation of the non-SRQ receive queues such that immediate
data is aligned on a 512 byte boundary. That alignment is necessary
to pass the immediate data without copying to the block layer. When
receiving an SRP_CMD with immediate data, postpone the ib_post_recv()
call until target_execute_cmd() has finished. See also
srpt_release_cmd().
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch does not change any functionality but makes the next patch
easier to read.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Neither a driver version number nor a release data is useful in
an upstream driver. Remove the word "InfiniBand" from the driver
description because recently RoCE support has been added to this
driver.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add documentation for those structure members for which it is missing.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Make sure that long strings occur on a single line as required by the
coding standard.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Use tabs instead of spaces for indentation. Make sure that multi-line
expressions have the operator at the end of a line instead of the start.
Avoid a complaint about a missing space in a ternary expression by
changing '(boolean) ? 1: 0' into 'boolean'.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch avoids that KASAN sporadically reports the following:
BUG: KASAN: use-after-free in rxe_run_task+0x1e/0x60 [rdma_rxe]
Read of size 1 at addr ffff88801c50d8f4 by task check/24830
CPU: 4 PID: 24830 Comm: check Not tainted 4.20.0-rc6-dbg+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
dump_stack+0x86/0xca
print_address_description+0x71/0x239
kasan_report.cold.5+0x242/0x301
__asan_load1+0x47/0x50
rxe_run_task+0x1e/0x60 [rdma_rxe]
rxe_post_send+0x4bd/0x8d0 [rdma_rxe]
srpt_zerolength_write+0xe1/0x160 [ib_srpt]
srpt_close_ch+0x8b/0xe0 [ib_srpt]
srpt_set_enabled+0xe7/0x150 [ib_srpt]
srpt_tpg_enable_store+0xc0/0x100 [ib_srpt]
configfs_write_file+0x157/0x1d0
__vfs_write+0xd7/0x3d0
vfs_write+0x102/0x290
ksys_write+0xab/0x130
__x64_sys_write+0x43/0x50
do_syscall_64+0x71/0x210
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Allocated by task 13856:
save_stack+0x43/0xd0
kasan_kmalloc+0xc7/0xe0
kasan_slab_alloc+0x11/0x20
kmem_cache_alloc+0x105/0x320
rxe_alloc+0xff/0x1f0 [rdma_rxe]
rxe_create_qp+0x9f/0x160 [rdma_rxe]
ib_create_qp+0xf5/0x690 [ib_core]
rdma_create_qp+0x6a/0x140 [rdma_cm]
srpt_cm_req_recv.cold.59+0x1588/0x237b [ib_srpt]
srpt_rdma_cm_req_recv.isra.35+0x1d5/0x220 [ib_srpt]
srpt_rdma_cm_handler+0x6f/0x100 [ib_srpt]
cma_listen_handler+0x59/0x60 [rdma_cm]
cma_ib_req_handler+0xd5b/0x2570 [rdma_cm]
cm_process_work+0x2e/0x110 [ib_cm]
cm_work_handler+0x2aae/0x502b [ib_cm]
process_one_work+0x481/0x9e0
worker_thread+0x67/0x5b0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
Freed by task 3440:
save_stack+0x43/0xd0
__kasan_slab_free+0x139/0x190
kasan_slab_free+0xe/0x10
kmem_cache_free+0xbc/0x330
rxe_elem_release+0x66/0xe0 [rdma_rxe]
rxe_destroy_qp+0x3f/0x50 [rdma_rxe]
ib_destroy_qp+0x140/0x360 [ib_core]
srpt_release_channel_work+0xdc/0x310 [ib_srpt]
process_one_work+0x481/0x9e0
worker_thread+0x67/0x5b0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Request permission to send immediate data during login. If the SRP
target grants this request, send the payload of write requests <= 8 KB
as immediate data.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Move the maximum initiator to target information unit length parameter
from struct srp_target_port into struct srp_rdma_ch. This patch does
not change any functionality but makes the next patch easier to read.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Since srp_rdma_ch.max_ti_iu_len is used in the hot path, move it to the
section with data structure members used in the hot path.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch avoids that the SCSI mid-layer keeps retrying forever if
ib_post_send() fails. This was discovered while testing immediate
data support and passing a too large num_sge value to ib_post_send().
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Reserve additional space for CDBs that contain more than sixteen bytes
and set the add_cdb_len field for such CDBs as required. From the SRP
standard: "The ADDITIONAL CDB LENGTH field contains the length in
dwords of the ADDITIONAL CDB field."
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch avoids that a warning is reported when building with W=1.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add constants and data structures to support immediate data. These
changes conform to SRP2r04.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch moves all constants that come from the SRP standard into the
include/scsi/srp.h header file.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The current code has 2 problems. It assumes that the RX ring for
the loopback packet is combined with the TX ring. This is not
true if the ethtool channels are set to non-combined mode. The
second problem is that it won't work on 57500 chips without
adjusting the logic to get the proper completion ring (cpr) pointer.
Fix both issues by locating the proper cpr pointer through the RX
ring.
Fixes: e44758b78ae8 ("bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
secpath_set is a wrapper for secpath_dup that will not perform
an allocation if the secpath attached to the skb has a reference count
of one, i.e., it doesn't need to be COW'ed.
Also, secpath_dup doesn't attach the secpath to the skb, it leaves
this to the caller.
Use secpath_set in places that immediately assign the return value to
skb.
This allows to remove skb->sp without touching these spots again.
secpath_dup can eventually be removed in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
