| Age | Commit message (Collapse) | Author |
|---|
|
Remove the redundant empty lines crept in.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Fix the bit width of the hse rtc divider because it's off by one.
Fixes: 2c87c9d33117 ("clk: stm32mp1: add RTC clock")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The divisor of ethptp_k and ck_hse_rtc clocks is: 'value register
plus one'.
Then CLK_DIVIDER_ALLOW_ZERO flag has no effect and is useless here.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The divider of HSI (clk-hsi-div) is power of two divider.
Fixes: 9bee94e7b7da ("clk: stm32mp1: Introduce STM32MP1 clock driver")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
index 8: ck_mcu is divided by 256 (not 512)
Fixes: e51d297e9a92 ("clk: stm32mp1: add Sub System clocks")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
ck_csi is used for IO compensation so it should be
considered as "always-on" and kept on.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
STM32MP1 clock IP offers lots of Kernel clocks that are shared
by multiple IP's at the same time.
Then boot loader applies a clock tree that allows to use all IP's
at same time and with the maximum of performance.
Not change parents on a change rate on kernel clocks ensures
the integrity of the system.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Fixes parent clock for axi, fdcan, sai and adc12 clocks.
Fixes: e51d297e9a92 ("clk: stm32mp1: add Sub System clocks")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
I noticed that modprobe clk-twl6040 can fail after a cold boot with:
abe_cm:clk:0010:0: failed to enable
...
Unhandled fault: imprecise external abort (0x1406) at 0xbe896b20
WARNING: CPU: 1 PID: 29 at drivers/clk/clk.c:828 clk_core_disable_lock+0x18/0x24
...
(clk_core_disable_lock) from [<c0123534>] (_disable_clocks+0x18/0x90)
(_disable_clocks) from [<c0124040>] (_idle+0x17c/0x244)
(_idle) from [<c0125ad4>] (omap_hwmod_idle+0x24/0x44)
(omap_hwmod_idle) from [<c053a038>] (sysc_runtime_suspend+0x48/0x108)
(sysc_runtime_suspend) from [<c06084c4>] (__rpm_callback+0x144/0x1d8)
(__rpm_callback) from [<c0608578>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c0607034>] (rpm_suspend+0x120/0x694)
(rpm_suspend) from [<c0607a78>] (__pm_runtime_idle+0x60/0x84)
(__pm_runtime_idle) from [<c053aaf0>] (sysc_probe+0x874/0xf2c)
(sysc_probe) from [<c05fecd4>] (platform_drv_probe+0x48/0x98)
After searching around for a similar issue, I came across an earlier fix
that never got merged upstream in the Android tree for glass-omap-xrr02.
There is patch "MFD: twl6040-codec: Implement PDMCLK cold temp errata"
by Misael Lopez Cruz <misael.lopez@ti.com>.
Based on my observations, this fix is also needed when cold booting
devices, and not just for deeper idle modes. Since we now have a clock
driver for pdmclk, let's fix the issue in twl6040_pdmclk_prepare().
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The current implementation of gpio-gate-clk enables/disables the clock
using the GPIO in the ->enable() and ->disable() clock callbacks. This
requires the GPIO to be configurable in atomic contexts. While it is
the case for most memory-mapped GPIO controllers, it is not the case
for GPIO expanders on I2C or SPI.
This commit extends the gpio-gate-clk to check whether the GPIO calls
require sleeping or not. If sleeping is not required, the current
implementation based on ->enable()/->disable() is kept. However, if
sleeping is needed, we instead implement the logic in the ->prepare()
and ->unprepare() hooks. Thanks to this, a gate clock connected to a
GPIO on a GPIO expander can be controlled with the existing driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[sboyd@kernel.org: Mark clk ops static]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The clk-rpmh driver only supports on and off RPMh clock resources. Let's
extend the driver by adding support for clocks that are managed by a
different type of RPMh resource known as Bus Clock Manager(BCM). The BCM
is a configurable shared resource aggregator that scales performance
based on a set of frequency points. The Qualcomm IP Accelerator (IPA)
clock is an example of a resource that is managed by the BCM and this a
requirement from the IPA driver in order to scale its core clock.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
These are in fact two clocks, they shouldn't be exposed as one. One is
required for accessing LCD controller registers (peripheral clock), while
other (AXI clock) can be optionally used as a pixel clock source for the
panel.
LCDC can alternatively use different clocks than the Display 1 AXI clock
for generating the pixel clock: the second AXI clock (fixed in this
commit too), the HDMI PLL, or the AXI bus clock.
They should really be controlled independently.
Link: https://lists.freedesktop.org/archives/dri-devel/2019-January/203975.html
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Need to set the update bit in UNIPHIER_CLK_CPUGEAR_UPD to update
the CPU-gear value.
Fixes: d08f1f0d596c ("clk: uniphier: add CPU-gear change (cpufreq) support")
Cc: linux-stable@vger.kernel.org
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/clk/samsung/clk-s3c2443.c: In function ‘s3c2443_common_clk_init’:
drivers/clk/samsung/clk-s3c2443.c:390:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
samsung_clk_register_alias(ctx, s3c2450_aliases,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ARRAY_SIZE(s3c2450_aliases));
~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/clk/samsung/clk-s3c2443.c:393:2: note: here
case S3C2416:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Platform driver driver_override field should not be initialized from
const memory because the core later kfree() it. If driver_override is
manually set later through sysfs, kfree() of old value leads to:
$ echo "new_value" > /sys/bus/platform/drivers/.../driver_override
kernel BUG at ../mm/slub.c:3960!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
...
(kfree) from [<c058e8c0>] (platform_set_driver_override+0x84/0xac)
(platform_set_driver_override) from [<c058e908>] (driver_override_store+0x20/0x34)
(driver_override_store) from [<c031f778>] (kernfs_fop_write+0x100/0x1dc)
(kernfs_fop_write) from [<c0296de8>] (__vfs_write+0x2c/0x17c)
(__vfs_write) from [<c02970c4>] (vfs_write+0xa4/0x188)
(vfs_write) from [<c02972e8>] (ksys_write+0x4c/0xac)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
The clk-exynos5-subcmu driver uses override only for the purpose of
creating meaningful names for children devices (matching names of power
domains, e.g. DISP, MFC). The driver_override was not developed for
this purpose so just switch to default names of devices to fix the
issue.
Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
platform_device_alloc() failure
During initialization of subdevices if platform_device_alloc() failed,
returned NULL pointer will be later dereferenced. Add proper error
paths to exynos5_clk_register_subcmu(). The return value of this
function is still ignored because at this stage of init there is nothing
we can do.
Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch fixes a subtle PACKET_ORIGDEV regression which was a side
effect of fixes introduced by:
6a9e461f6fe4 bonding: pass link-local packets to bonding master also.
... to:
b89f04c61efe bonding: deliver link-local packets with skb->dev set to link that packets arrived on
While 6a9e461f6fe4 restored pre-b89f04c61efe presence of link-local
packets on bonding masters (which is required e.g. by linux bridges
participating in spanning tree or needed for lab-like setups created
with group_fwd_mask) it also caused the originating device
information to be lost due to cloning.
Maciej Żenczykowski proposed another solution that doesn't require
packet cloning and retains original device information - instead of
returning RX_HANDLER_PASS for all link-local packets it's now limited
only to packets from inactive slaves.
At the same time, packets passed to bonding masters retain correct
information about the originating device and PACKET_ORIGDEV can be used
to determine it.
This elegantly solves all issues so far:
- link-local packets that were removed from bonding masters
- LLDP daemons being forced to explicitly bind to slave interfaces
- PACKET_ORIGDEV having no effect on bond interfaces
Fixes: 6a9e461f6fe4 (bonding: pass link-local packets to bonding master also.)
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similiar to commit e94cd8113ce63 ("net: remove MTU limits for dummy and
ifb device"), MTU is irrelevant for VRF device. We init it as 64K while
limit it to [68, 1500] may make users feel confused.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enum LAST_DT_CORE_CLK needs updating as R8A774C0_CLK_CANFD
was recently added and it's the core clock with the highest
index.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Fixes: 2a6efbc6da5d248c ("clk: renesas: r8a774c0: Add missing CANFD clock")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the ARM clock as imx_clk_cpu type.
Will be used by cpufreq.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The arm pll bypass needs to propagate the rate upwards
in order for the cpufreq to work.
Fixes: b80522040cd3f ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the entry for the CLKO1 clock.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The CLKO2 clock source select list is the following as per the i.MX8M
Reference Manual:
000 - 25M_REF_CLK
001 - SYSTEM_PLL2_DIV5
010 - SYSTEM_PLL1_DIV2
011 - SYSTEM_PLL2_DIV6
100 - SYSTEM_PLL3_CLK
101 - AUDIO_PLL1_CLK
110 - VIDEO_PLL1_CLK
111 - 32K_REF_CLK
However, in imx8mq_clko2_sels[] only the first four entries are correct.
Fix it by adding the missing "sys3_pll2_out" entry in order to match
the description from the manual.
Fixes: b80522040cd3f ("clk: imx: Add clock driver for i.MX8MQ CCM")
Reported-by: Rogerio Pimentel <rogerio.silva@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The clocks list is missing the clocks for the M4 core.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add clock driver support for i.MX8MM SOC.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
New PLLs are introduced on i.MX8M Mini SOC.
PLL1416X is Integer PLL, PLL1443X is a Frac PLL.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This adds the missing clock for the SCC2 peripheral unit.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add clk scu set parents support.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Remove le32_to_cpu() on get_parent op]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
SCU clock can be used in a similar way by IMX8QXP and IMX8QM SoCs.
Make the driver support "fsl,scu-clk" fallback compatible string
to allow other SoCs to reuse the common part.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The arrays containing the mux selectors need to be of const pointer
to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The parents needs to be pointer to const pointer to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The parent_names needs to be pointer to const pointer to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
An issue has been found while testing zero-copy XDP that
causes a reset to be triggered. As it takes some time to
turn the carrier on after setting zc, and we already
start trying to transmit some packets, watchdog considers
this as an erroneous state and triggers a reset.
Don't do any work if netif carrier is not OK.
Fixes: 8221c5eba8c13 (ixgbe: add AF_XDP zero-copy Tx support)
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the driver clears the XDP xmit ring due to re-configuration or
teardown, in-progress ndo_xdp_xmit must be taken into consideration.
The ndo_xdp_xmit function is typically called from a NAPI context that
the driver does not control. Therefore, we must be careful not to
clear the XDP ring, while the call is on-going. This patch adds a
synchronize_rcu() to wait for napi(s) (preempt-disable regions and
softirqs), prior clearing the queue. Further, the __I40E_CONFIG_BUSY
flag is checked in the ndo_xdp_xmit implementation to avoid touching
the XDP xmit queue during re-configuration.
Fixes: d9314c474d4f ("i40e: add support for XDP_REDIRECT")
Fixes: 123cecd427b6 ("i40e: added queue pair disable/enable functions")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the RX rings are created they are also populated with buffers so
that packets can be received. Usually these are kernel buffers, but
for AF_XDP in zero-copy mode, these are user-space buffers and in this
case the application might not have sent down any buffers to the
driver at this point. And if no buffers are allocated at ring creation
time, no packets can be received and no interrupts will be generated so
the NAPI poll function that allocates buffers to the rings will never
get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once after
an XDP program has loaded and once after the umem is registered. This
take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: d0bcacd0a130 ("ixgbe: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the RX rings are created they are also populated with buffers
so that packets can be received. Usually these are kernel buffers,
but for AF_XDP in zero-copy mode, these are user-space buffers and
in this case the application might not have sent down any buffers
to the driver at this point. And if no buffers are allocated at ring
creation time, no packets can be received and no interrupts will be
generated so the NAPI poll function that allocates buffers to the
rings will never get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once
after an XDP program has loaded and once after the umem is registered.
This take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The enabling L3/L4 filtering for transmit switched packets for all
devices caused unforeseen issue on older devices when trying to send UDP
traffic in an ordered sequence. This bit was originally intended for X550
devices, which supported this feature, so limit the scope of this bit to
only X550 devices.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
|
|
When rpm_resume() desactivates the autosuspend timer, it should only
try to cancel hrtimer but not wait for the handler to finish, because
both rpm_resume() and pm_suspend_timer_fn() take the power.lock.
A deadlock is possible as follows:
CPU0 CPU1
rpm_resume()
spin_lock_irqsave
pm_suspend_timer_fn()
spin_lock_irqsave
pm_runtime_deactivate_timer()
hrtimer_cancel()
It is sufficient to call hrtimer_try_to_cancel() from
pm_runtime_deactivate_timer(), because dev->power.timer_expires
reset to 0 by it, so use that function instead of hrtimer_cancel().
Fixes: 8234f6734c5d ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Sunzhaosheng Sun(Zhaosheng) <sunzhaosheng@hisilicon.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Booting 4.20 on SolidRun Clearfog issues this warning with DMA API
debug enabled:
WARNING: CPU: 0 PID: 555 at kernel/dma/debug.c:1230 check_sync+0x514/0x5bc
mvneta f1070000.ethernet: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000002dd7dc00] [size=240 bytes]
Modules linked in: ahci mv88e6xxx dsa_core xhci_plat_hcd xhci_hcd devlink armada_thermal marvell_cesa des_generic ehci_orion phy_armada38x_comphy mcp3021 spi_orion evbug sfp mdio_i2c ip_tables x_tables
CPU: 0 PID: 555 Comm: bridge-network- Not tainted 4.20.0+ #291
Hardware name: Marvell Armada 380/385 (Device Tree)
[<c0019638>] (unwind_backtrace) from [<c0014888>] (show_stack+0x10/0x14)
[<c0014888>] (show_stack) from [<c07f54e0>] (dump_stack+0x9c/0xd4)
[<c07f54e0>] (dump_stack) from [<c00312bc>] (__warn+0xf8/0x124)
[<c00312bc>] (__warn) from [<c00313b0>] (warn_slowpath_fmt+0x38/0x48)
[<c00313b0>] (warn_slowpath_fmt) from [<c00b0370>] (check_sync+0x514/0x5bc)
[<c00b0370>] (check_sync) from [<c00b04f8>] (debug_dma_sync_single_range_for_cpu+0x6c/0x74)
[<c00b04f8>] (debug_dma_sync_single_range_for_cpu) from [<c051bd14>] (mvneta_poll+0x298/0xf58)
[<c051bd14>] (mvneta_poll) from [<c0656194>] (net_rx_action+0x128/0x424)
[<c0656194>] (net_rx_action) from [<c000a230>] (__do_softirq+0xf0/0x540)
[<c000a230>] (__do_softirq) from [<c00386e0>] (irq_exit+0x124/0x144)
[<c00386e0>] (irq_exit) from [<c009b5e0>] (__handle_domain_irq+0x58/0xb0)
[<c009b5e0>] (__handle_domain_irq) from [<c03a63c4>] (gic_handle_irq+0x48/0x98)
[<c03a63c4>] (gic_handle_irq) from [<c0009a10>] (__irq_svc+0x70/0x98)
...
This appears to be caused by mvneta_rx_hwbm() calling
dma_sync_single_range_for_cpu() with the wrong struct device pointer,
as the buffer manager device pointer is used to map and unmap the
buffer. Fix this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The changes to fix those are two invasive for backporting.
Just disable the feature in 4.20 and 5.0.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org> [4.20+]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When a dce80 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
optimize_bandwidth was using dce100_prepare_bandwidth this is incorrect
[How]
change it to dce100_optimize_bandwidth
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The master clock is actually named masterck earlier in the driver. Having
"mck" in the parent list means that it can never be selected.
Fixes: 1eabdc2f9dd8 ("clk: at91: add at91sam9x5 PMCs driver")
Fixes: a2038077de9a ("clk: at91: add sama5d2 PMC driver")
Fixes: 084b696bb509 ("clk: at91: add sama5d4 pmc driver")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
nck() looks at the last id in an array and unfortunately,
at91sam9x35_periphck has a sentinel, hence the id is 0 and the calculated
number of peripheral clocks is 1 instead of a maximum of 31.
Fixes: 1eabdc2f9dd8 ("clk: at91: add at91sam9x5 PMCs driver")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some final pin control fixes (I hope) to round off the v5.0 pin
control development cycle.
Only driver fixes, one for stable:
- Meson8B fixup for the sdc pins
- Fix SDC tile position for Qualcomm QCS404"
* tag 'pinctrl-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: meson: meson8b: fix the sdxc_a data 1..3 pins
pinctrl: qcom: qcs404: Correct SDC tile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes for the v5.0 series:
- Per-instance irqchip on the MT7621
- Avoid direction setting using pin control on MMP2"
* tag 'gpio-v5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pxa: avoid attempting to set pin direction via pinctrl on MMP2
gpio: MT7621: use a per instance irq_chip structure
|
|
Pull MTD fixes from Boris Brezillon:
- Don't add a digit to MTD-backed nvmem device names
- Make sure powernv flash names are unique
* tag 'mtd/fixes-for-5.0-rc8' of git://git.infradead.org/linux-mtd:
mtd: powernv_flash: Fix device registration error
mtd: Use mtd->name when registering nvmem device
|
|
If we skipped all the connectors that were not part of a tile, we would
leave conn_seq=0 and conn_configured=0, convincing ourselves that we
had stagnated in our configuration attempts. Avoid this situation by
starting conn_seq=ALL_CONNECTORS, and repeating until we find no more
connectors to configure.
Fixes: 754a76591b12 ("drm/i915/fbdev: Stop repeating tile configuration on stagnation")
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190215123019.32283-1-chris@chris-wilson.co.uk
Cc: <stable@vger.kernel.org> # v3.19+
(cherry picked from commit d9b308b1f8a1acc0c3279f443d4fe0f9f663252e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Pull networking fixes from David Miller:
1) Fix suspend and resume in mt76x0u USB driver, from Stanislaw
Gruszka.
2) Missing memory barriers in xsk, from Magnus Karlsson.
3) rhashtable fixes in mac80211 from Herbert Xu.
4) 32-bit MIPS eBPF JIT fixes from Paul Burton.
5) Fix for_each_netdev_feature() on big endian, from Hauke Mehrtens.
6) GSO validation fixes from Willem de Bruijn.
7) Endianness fix for dwmac4 timestamp handling, from Alexandre Torgue.
8) More strict checks in tcp_v4_err(), from Eric Dumazet.
9) af_alg_release should NULL out the sk after the sock_put(), from Mao
Wenan.
10) Missing unlock in mac80211 mesh error path, from Wei Yongjun.
11) Missing device put in hns driver, from Salil Mehta.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
sky2: Increase D3 delay again
vhost: correctly check the return value of translate_desc() in log_used()
net: netcp: Fix ethss driver probe issue
net: hns: Fixes the missing put_device in positive leg for roce reset
net: stmmac: Fix a race in EEE enable callback
qed: Fix iWARP syn packet mac address validation.
qed: Fix iWARP buffer size provided for syn packet processing.
r8152: Add support for MAC address pass through on RTL8153-BD
mac80211: mesh: fix missing unlock on error in table_path_del()
net/mlx4_en: fix spelling mistake: "quiting" -> "quitting"
net: crypto set sk to NULL when af_alg_release.
net: Do not allocate page fragments that are not skb aligned
mm: Use fixed constant in page_frag_alloc instead of size + 1
tcp: tcp_v4_err() should be more careful
tcp: clear icsk_backoff in tcp_write_queue_purge()
net: mv643xx_eth: disable clk on error path in mv643xx_eth_shared_probe()
qmi_wwan: apply SET_DTR quirk to Sierra WP7607
net: stmmac: handle endianness in dwmac4_get_timestamp
doc: Mention MSG_ZEROCOPY implementation for UDP
mlxsw: __mlxsw_sp_port_headroom_set(): Fix a use of local variable
...
|
