| Age | Commit message (Collapse) | Author |
|---|
|
A recent change to the driver exposed a bug where the MAC RX
filters (unicast MAC, broadcast MAC, and multicast MAC) are
configured and enabled before the RX path is fully initialized.
The result of this bug is that after the PHY is started packets
that match these MAC RX filters start to flow into the RX FIFO.
And then, after rx_init() is completed, these packets will go
into the driver RX ring as well. If enough packets are received
to fill the RX ring (default size is 128 packets) before the call
to request_irq() completes, the driver RX function becomes stuck.
This bug is intermittent but is most likely to be seen where the
oob_net0 interface is connected to a busy network with lots of
broadcast and multicast traffic.
All the MAC RX filters must be disabled until the RX path is ready,
i.e. all initialization is done and all the IRQs are installed.
Fixes: f7442a634ac0 ("mlxbf_gige: call request_irq() after NAPI initialized")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240809163612.12852-1-davthompson@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If the dm_resume method is called on a device that is not suspended, the
method will suspend the device briefly, before resuming it (so that the
table will be swapped).
However, there was a bug that the return value of dm_suspended_md was not
checked. dm_suspended_md may return an error when it is interrupted by a
signal. In this case, do_resume would call dm_swap_table, which would
return -EINVAL.
This commit fixes the logic, so that error returned by dm_suspend is
checked and the resume operation is undone.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Cc: stable@vger.kernel.org
|
|
This commit changes device mapper, so that it returns -ERESTARTSYS
instead of -EINTR when it is interrupted by a signal (so that the ioctl
can be restarted).
The manpage signal(7) says that the ioctl function should be restarted if
the signal was handled with SA_RESTART.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
|
|
Commit 60fa6ae6e6d0 ("ACPI: EC: Install address space handler at the
namespace root") caused _REG methods for EC operation regions outside
the EC device scope to be evaluated which on some systems leads to the
evaluation of _REG methods in the scopes of device objects representing
devices that are not present and not functional according to the _STA
return values. Some of those device objects represent EC "alternatives"
and if _REG is evaluated for their operation regions, the platform
firmware may be confused and the platform may start to behave
incorrectly.
To avoid this problem, only evaluate _REG for EC operation regions
located in the scopes of device objects representing known-to-be-present
devices.
For this purpose, partially revert commit 60fa6ae6e6d0 and trigger the
evaluation of _REG for EC operation regions from acpi_bus_attach() for
the known-valid devices.
Fixes: 60fa6ae6e6d0 ("ACPI: EC: Install address space handler at the namespace root")
Link: https://lore.kernel.org/linux-acpi/1f76b7e2-1928-4598-8037-28a1785c2d13@redhat.com
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2298938
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2302253
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: All applicable <stable@vger.kernel.org>
Link: https://patch.msgid.link/23612351.6Emhk5qWAg@rjwysocki.net
|
|
A subsequent change will need to pass a depth argument to
acpi_execute_reg_methods(), so prepare that function for it.
No intentional functional changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: All applicable <stable@vger.kernel.org>
Link: https://patch.msgid.link/8451567.NyiUUSuA9g@rjwysocki.net
|
|
Large blocks of data time out when reading because we don't wait long
enough for the transfer to complete. Scale our timeouts based on the
amount of data we are tranferring, with a healthy dose of pessimism.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20240809201540.3363243-1-sean.anderson@linux.dev
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit 0e6b6dedf168 ("Revert "ACPI: EC: Evaluate orphan
_REG under EC device") because the problem addressed by it will be
addressed differently in what follows.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: All applicable <stable@vger.kernel.org>
Link: https://patch.msgid.link/3236716.5fSG56mABF@rjwysocki.net
|
|
doorbell rings
After napi_complete_done() is called when NAPI is polling in the current
process context, another NAPI may be scheduled and start running in
softirq on another CPU and may ring the doorbell before the current CPU
does. When combined with unnecessary rings when there is no need to arm
the CQ, it triggers error paths in the hardware.
This patch fixes this by calling napi_complete_done() after doorbell
rings. It limits the number of unnecessary rings when there is
no need to arm. MANA hardware specifies that there must be one doorbell
ring every 8 CQ wraparounds. This driver guarantees one doorbell ring as
soon as the number of consumed CQEs exceeds 4 CQ wraparounds. In practical
workloads, the 4 CQ wraparounds proves to be big enough that it rarely
exceeds this limit before all the napi weight is consumed.
To implement this, add a per-CQ counter cq->work_done_since_doorbell,
and make sure the CQ is armed as soon as passing 4 wraparounds of the CQ.
Cc: stable@vger.kernel.org
Fixes: e1b5683ff62e ("net: mana: Move NAPI from EQ to CQ")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Link: https://patch.msgid.link/1723219138-29887-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Simpler and avoids manual pointer addition.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240809044957.4534-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patches for v6.12
This is a fairly light pull request since ath12k is still working on
MLO-related changes, and the other drivers are mostly in maintenance
mode with a few cleanups and bug fixes.
Major changes:
ath12k
* DebugFS support for transmit DE stats
* Make ASPM support hardware-dependent
* Align BSS Channel information command and message with firmware
ath11k
* Use work queue for beacon tx events
ath9k
* Use devm for gpio_request_one
* Use unmanaged PCI functions in ath9k_pci_owl_loader()
|
|
Commit 5c4250092fad ("wifi: mwl8k: Avoid -Wflex-array-member-not-at-end
warnings") introduced tagged `struct mwl8k_cmd_pkt_hdr`. We want to
ensure that when new members need to be added to the flexible structure,
they are always included within this tagged struct.
We use `static_assert()` to ensure that the memory layout for both
the flexible structure and the tagged struct is the same after any
changes.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/ZrVCg51Q9M2fTPaF@cute
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patch for v6.11
We have a single patch for the next 6.11-rc which introduces a
workaround to ath12k which addresses a WCN7850 hardware issue that
prevents proper operation with unaligned transmit buffers.
|
|
The code to lookup the scatter gather table entry assumed that it was
possible to use sg_virt() in order to lookup the DMA address in a mapped
scatter gather table. However, this assumption is incorrect as the DMA
mapping code may merge multiple entries into one. In that case, the DMA
address space may have e.g. two consecutive pages which is correctly
represented by the scatter gather list entry, however the virtual
addresses for these two pages may differ and the relationship cannot be
resolved anymore.
Avoid this problem entirely by working with the offset into the mapped
area instead of using virtual addresses. With that we only use the DMA
length and DMA address from the scatter gather list entries. The
underlying DMA/IOMMU code is therefore free to merge two entries into
one even if the virtual addresses space for the area is not continuous.
Fixes: 90db50755228 ("wifi: iwlwifi: use already mapped data when TXing an AMSDU")
Reported-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Closes: https://lore.kernel.org/r/ZrNRoEbdkxkKFMBi@debian.local
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240812110640.460514-1-benjamin@sipsolutions.net
|
|
When disabling wifi mt7921_ipv6_addr_change() is called as a notifier.
At this point mvif->phy is already NULL so we cannot use it here.
Signed-off-by: Bert Karwatzki <spasswolf@web.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240812104542.80760-1-spasswolf@web.de
|
|
In RS485 mode, the RTS pin is driven high by hardware when the transmitter
is operating. This behaviour cannot be changed. This means that the driver
should claim that it supports SER_RS485_RTS_ON_SEND and not
SER_RS485_RTS_AFTER_SEND.
Otherwise, when configuring the port with the SER_RS485_RTS_ON_SEND, one
get the following warning:
kern.warning kernel: atmel_usart_serial atmel_usart_serial.2.auto:
ttyS1 (1): invalid RTS setting, using RTS_AFTER_SEND instead
which is contradictory with what's really happening.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Cc: stable <stable@kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Fixes: af47c491e3c7 ("serial: atmel: Fill in rs485_supported")
Link: https://lore.kernel.org/r/20240808060637.19886-1-othacehe@gnu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 6e20753da6bc ("tty: vt: conmakehash: cope with abs_srctree no
longer in env") included <linux/limits.h>, which invoked another
(wrong) patch that tried to address a build error on macOS.
According to the specification [1], the correct header to use PATH_MAX
is <limits.h>.
The minimal fix would be to replace <linux/limits.h> with <limits.h>.
However, the following commits seem questionable to me:
- 3bd85c6c97b2 ("tty: vt: conmakehash: Don't mention the full path of the input in output")
- 6e20753da6bc ("tty: vt: conmakehash: cope with abs_srctree no longer in env")
These commits made too many efforts to cope with a comment header in
drivers/tty/vt/consolemap_deftbl.c:
/*
* Do not edit this file; it was automatically generated by
*
* conmakehash drivers/tty/vt/cp437.uni > [this file]
*
*/
With this commit, the header part of the generate C file will be
simplified as follows:
/*
* Automatically generated file; Do not edit.
*/
BTW, another series of excessive efforts for a comment header can be
seen in the following:
- 5ef6dc08cfde ("lib/build_OID_registry: don't mention the full path of the script in output")
- 2fe29fe94563 ("lib/build_OID_registry: avoid non-destructive substitution for Perl < 5.13.2 compat")
[1]: https://pubs.opengroup.org/onlinepubs/009695399/basedefs/limits.h.html
Fixes: 6e20753da6bc ("tty: vt: conmakehash: cope with abs_srctree no longer in env")
Cc: stable <stable@kernel.org>
Reported-by: Daniel Gomez <da.gomez@samsung.com>
Closes: https://lore.kernel.org/all/20240807-macos-build-support-v1-11-4cd1ded85694@samsung.com/
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20240809160853.1269466-1-masahiroy@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With "earlycon initcall_debug=1 loglevel=8" in bootargs, kernel
sometimes boot hang. It is because normal console still is not ready,
but runtime suspend is called, so early console putchar will hang
in waiting TRDE set in UARTSTAT.
The lpuart driver has auto suspend delay set to 3000ms, but during
uart_add_one_port, a child device serial ctrl will added and probed with
its pm runtime enabled(see serial_ctrl.c).
The runtime suspend call path is:
device_add
|-> bus_probe_device
|->device_initial_probe
|->__device_attach
|-> pm_runtime_get_sync(dev->parent);
|-> pm_request_idle(dev);
|-> pm_runtime_put(dev->parent);
So in the end, before normal console ready, the lpuart get runtime
suspended. And earlycon putchar will hang.
To address the issue, mark last busy just after pm_runtime_enable,
three seconds is long enough to switch from bootconsole to normal
console.
Fixes: 43543e6f539b ("tty: serial: fsl_lpuart: Add runtime pm support")
Cc: stable <stable@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240808140325.580105-1-peng.fan@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
traversal
Current issue:
- The `target_list_lock` spinlock is held while iterating over
target_list() entries.
- Mid-loop, the lock is released to call __netpoll_cleanup(), then
reacquired.
- This practice compromises the protection provided by
`target_list_lock`.
Reason for current design:
1. __netpoll_cleanup() may sleep, incompatible with holding a spinlock.
2. target_list_lock must be a spinlock because write_msg() cannot sleep.
(See commit b5427c27173e ("[NET] netconsole: Support multiple logging
targets"))
Defer the cleanup of the netpoll structure to outside the
target_list_lock() protected area. Create another list
(target_cleanup_list) to hold the entries that need to be cleaned up,
and clean them using a mutex (target_cleanup_list_lock).
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The return flow in netconsole's dynamic functions is currently
inconsistent. This patch aims to streamline and standardize the process
by ensuring that the mutex is unlocked before returning the ret value.
Additionally, this update includes a minor functional change where
certain strnlen() operations are performed with the
dynamic_netconsole_mutex locked. This adjustment is not anticipated to
cause any issues, however, it is crucial to document this change for
clarity.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Update variable names from err to ret in cases where the variable may
return non-error values.
This change facilitates a forthcoming patch that relies on ret being
used consistently to handle return values, regardless of whether they
indicate an error or not.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
netconsole incorrectly mixes int and ssize_t types by using int for
return variables in functions that should return ssize_t.
This is fixed by updating the return variables to the appropriate
ssize_t type, ensuring consistency across the function definitions.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add LJCA GPIO support for the Lunar Lake platform.
New HID taken from out of tree ivsc-driver git repo.
Link: https://github.com/intel/ivsc-driver/commit/47e7c4a446c8ea8c741ff5a32fa7b19f9e6fd47e
Cc: stable <stable@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240812095038.555837-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit bf20c69cf3cf9c6445c4925dd9a8a6ca1b78bfdf.
During tcpm_init() stage, if the VBUS is still present after
tcpm_reset_port(), then we assume that VBUS will off and goto safe0v
after a specific discharge time. Following a TCPM_VBUS_EVENT event if
VBUS reach to off state. TCPM_VBUS_EVENT event may be set during
PORT_RESET handling stage. If pd_events reset to 0 after TCPM_VBUS_EVENT
set, we will lost this VBUS event. Then the port state machine may stuck
at one state.
Before:
[ 2.570172] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev1 NONE_AMS]
[ 2.570179] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 2.570182] pending state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED @ 920 ms [rev1 NONE_AMS]
[ 3.490213] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [delayed 920 ms]
[ 3.490220] Start toggling
[ 3.546050] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 3.546057] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
After revert this patch, we can see VBUS off event and the port will goto
expected state.
[ 2.441992] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev1 NONE_AMS]
[ 2.441999] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 2.442002] pending state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED @ 920 ms [rev1 NONE_AMS]
[ 2.442122] VBUS off
[ 2.442125] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev1 NONE_AMS]
[ 2.442127] VBUS VSAFE0V
[ 2.442351] CC1: 0 -> 0, CC2: 0 -> 0 [state SNK_UNATTACHED, polarity 0, disconnected]
[ 2.442357] Start toggling
[ 2.491850] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 2.491858] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
[ 2.491863] pending state change SRC_ATTACH_WAIT -> SNK_TRY @ 200 ms [rev1 NONE_AMS]
[ 2.691905] state change SRC_ATTACH_WAIT -> SNK_TRY [delayed 200 ms]
Fixes: bf20c69cf3cf ("usb: typec: tcpm: clear pd_event queue in PORT_RESET")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240809112901.535072-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The command execution routines need to return the amount of
data that was transferred when succesful.
This fixes an issue where the alternate modes and the power
delivery capabilities are not getting registered.
Fixes: 5e9c1662a89b ("usb: typec: ucsi: rework command execution functions")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240809150343.286942-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Stall handling is managed in the 'process_*' functions, which are called
right before the 'goto' stall handling code snippet. Thus, there should
be a return after the 'process_*' functions. Otherwise, the stall code may
run twice.
Fixes: 1b349f214ac7 ("usb: xhci: add 'goto' for halted endpoint check in handle_tx_event()")
Reported-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240809124408.505786-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If xhci_mem_init() fails, it calls into xhci_mem_cleanup() to mop
up the damage. If it fails early enough, before xhci->interrupters
is allocated but after xhci->max_interrupters has been set, which
happens in most (all?) cases, things get uglier, as xhci_mem_cleanup()
unconditionally derefences xhci->interrupters. With prejudice.
Gate the interrupt freeing loop with a check on xhci->interrupters
being non-NULL.
Found while debugging a DMA allocation issue that led the XHCI driver
on this exact path.
Fixes: c99b38c41234 ("xhci: add support to allocate several interrupters")
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # 6.8+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240809124408.505786-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
thunderbolt: Fixes for v6.11-rc3
This includes following USB4/Thunderbolt fixes for v6.11-rc3:
- Fix memory leak in debugfs sideband register access
- Fix hang when host router NVM is upgraded and there is another host
connected.
Both have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.11-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Mark XDomain as unplugged when router is removed
thunderbolt: Fix memory leaks in {port|retimer}_sb_regs_write()
|
|
There is a small window in ssam_serial_hub_probe() where the controller
is initialized but has not been started yet. Specifically, between
ssam_controller_init() and ssam_controller_start(). Any failure in this
window, for example caused by a failure of serdev_device_open(),
currently results in an incorrect warning being emitted.
In particular, any failure in this window results in the controller
being destroyed via ssam_controller_destroy(). This function checks the
state of the controller and, in an attempt to validate that the
controller has been cleanly shut down before we try and deallocate any
resources, emits a warning if that state is not SSAM_CONTROLLER_STOPPED.
However, since we have only just initialized the controller and have not
yet started it, its state is SSAM_CONTROLLER_INITIALIZED. Note that this
is the only point at which the controller has this state, as it will
change after we start the controller with ssam_controller_start() and
never revert back. Further, at this point no communication has taken
place and the sender and receiver threads have not been started yet (and
we may not even have an open serdev device either).
Therefore, it is perfectly safe to call ssam_controller_destroy() with a
state of SSAM_CONTROLLER_INITIALIZED. This, however, means that the
warning currently being emitted is incorrect. Fix it by extending the
check.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240811124645.246016-1-luzmaximilian@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Triggered by a kref decrement, destroy_workqueue() may be called from
within a work item for destroying its own workqueue. This illegal
situation is averted by adding a module-global workqueue for exclusive
use of the offending work item. Other work items continue to be queued
on per-device workqueues to ensure performance.
Reported-by: syzbot+91dbdfecdd3287734d8e@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Closes: https://lore.kernel.org/lkml/0000000000000ab25a061e1dfe9f@google.com/
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Link: https://lore.kernel.org/r/20240801121126.60183-1-eli.billauer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SAM client device nodes for the Surface Laptop Studio 6 (SL6). The
SL6 is similar to the SL5, with the typical battery/AC, platform
profile, and HID nodes. It also has support for the newly supported fan
interface.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240811131948.261806-6-luzmaximilian@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
for Surface Laptop 5
The EC on the Surface Laptop 5 exposes the fan interface. With the
recently introduced driver for it, we can now also enable it here. In
addition, also enable the thermal sensor interface.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240811131948.261806-5-luzmaximilian@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add SAM client device nodes for the Surface Laptop Studio 2 (SLS2). The
SLS2 is quite similar to the SLS1, but it does not provide the touchpad
as a SAM-HID device. Therefore, add a new node group for the SLS2 and
update the comments accordingly. In addition, it uses the new fan
control interface.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240811131948.261806-4-luzmaximilian@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add SAM client device nodes for the Surface Laptop Go 3. It seems to use
the same SAM client devices as the Surface Laptop Go 1 and 2, so re-use
their node group.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240811131948.261806-3-luzmaximilian@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add SAM client device nodes for the Surface Pro 10. It seems to use the
same SAM client devices as the Surface Pro 9, so re-use its node group.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240811131948.261806-2-luzmaximilian@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The new ROG Ally X functions the same as the previus model so we can use
the same method to ensure the MCU USB devices wake and reconnect
correctly.
Given that two devices marks the start of a trend, this patch also adds
a quirk table to make future additions easier if the MCU is the same.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240805234603.38736-1-luke@ljones.dev
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add Yanteng Si as MODULE_AUTHOR of Loongson DWMAC PCI driver.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The new generation Loongson LS2K2000 SoC and LS7A2000 chipset are
equipped with the network controllers called Loongson GNET. It's the
single and multi DMA-channels Loongson GMAC but with a PHY attached.
Here is the summary of the DW GMAC features the controller has:
DW GMAC IP-core: v3.73a
Speeds: 10/100/1000Mbps
Duplex: Full (both versions), Half (LS2K2000 GNET only)
DMA-descriptors type: enhanced
L3/L4 filters availability: Y
VLAN hash table filter: Y
PHY-interface: GMII (PHY is integrated into the chips)
Remote Wake-up support: Y
Mac Management Counters (MMC): Y
Number of additional MAC addresses: 5
MAC Hash-based filter: Y
Hash Table Size: 256
AV feature: Y (LS2K2000 GNET only)
DMA channels: 8 (LS2K2000 GNET), 1 (LS7A2000 GNET)
Let's update the Loongson DWMAC driver to supporting the new Loongson
GNET controller. The change is mainly trivial: the driver shall be
bound to the PCIe device with DID 0x7a13, and the device-specific
setup() method shall be called for it. The only peculiarity concerns
the integrated PHY speed change procedure. The PHY has a weird problem
with switching from the low speeds to 1000Mbps mode. The speedup
procedure requires the PHY-link re-negotiation. So the suggested
change provide the device-specific fix_mac_speed() method to overcome
the problem.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Loongson DWMAC driver currently supports the Loongson GMAC
devices (based on the DW GMAC v3.50a/v3.73a IP-core) installed to the
LS2K1000 SoC and LS7A1000 chipset. But recently a new generation
LS2K2000 SoC was released with the new version of the Loongson GMAC
synthesized in. The new controller is based on the DW GMAC v3.73a
IP-core with the AV-feature enabled, which implies the multi
DMA-channels support. The multi DMA-channels feature has the next
vendor-specific peculiarities:
1. Split up Tx and Rx DMA IRQ status/mask bits:
Name Tx Rx
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000;
DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000;
DMA_STATUS_NIS = 0x00040000 | 0x00020000;
DMA_STATUS_AIS = 0x00010000 | 0x00008000;
DMA_STATUS_FBI = 0x00002000 | 0x00001000;
2. Custom Synopsys ID hardwired into the GMAC_VERSION.SNPSVER register
field. It's 0x10 while it should have been 0x37 in accordance with
the actual DW GMAC IP-core version.
3. There are eight DMA-channels available meanwhile the Synopsys DW
GMAC IP-core supports up to three DMA-channels.
4. It's possible to have each DMA-channel IRQ independently delivered.
The MSI IRQs must be utilized for that.
Thus in order to have the multi-channels Loongson GMAC controllers
supported let's modify the Loongson DWMAC driver in accordance with
all the peculiarities described above:
1. Create the multi-channels Loongson GMAC-specific
stmmac_dma_ops::dma_interrupt()
stmmac_dma_ops::init_chan()
callbacks due to the non-standard DMA IRQ CSR flags layout.
2. Create the Loongson DWMAC-specific platform setup() method
which gets to initialize the DMA-ops with the dwmac1000_dma_ops
instance and overrides the callbacks described in 1. The method also
overrides the custom Synopsys ID with the real one in order to have
the rest of the HW-specific callbacks correctly detected by the driver
core.
3. Make sure the platform setup() method enables the flow control and
duplex modes supported by the controller.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Loongson GMAC driver currently supports the network controllers
installed on the LS2K1000 SoC and LS7A1000 chipset, for which the GMAC
devices are required to be defined in the platform device tree source.
But Loongson machines may have UEFI (implies ACPI) or PMON/UBOOT
(implies FDT) as the system bootloaders. In order to have both system
configurations support let's extend the driver functionality with the
case of having the Loongson GMAC probed on the PCI bus with no device
tree node defined for it. That requires to make the device DT-node
optional, to rely on the IRQ line detected by the PCI core and to
have the MDIO bus ID calculated using the PCIe Domain+BDF numbers.
In order to have the device probe() and remove() methods less
complicated let's move the DT- and ACPI-specific code to the
respective sub-functions.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Loongson GNET device support is about to be added in one of the
next commits. As another preparation for that introduce the PCI device
info data with a setup() callback performing the device-specific
platform data initializations. Currently it is utilized for the
already supported Loongson GMAC device only.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PHY-interface of the Loongson GMAC device is RGMII with no internal
delays added to the data lines signal. So to comply with that let's
pre-initialize the platform-data field with the respective enum
constant.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Reference and PTP clocks rate of the Loongson GMAC devices is 125MHz.
(So is in the GNET devices which support is about to be added.) Set
the respective plat_stmmacenet_data field up in accordance with that
so to have the coalesce command and timestamping work correctly.
Fixes: 30bba69d7db4 ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Loongson delivers two types of the network devices: Loongson GMAC and
Loongson GNET in the framework of four SOC/Chipsets revisions:
Chip Network PCI Dev ID Synopys Version DMA-channel
LS2K1000 SOC GMAC 0x7a03 v3.50a/v3.73a 1
LS7A1000 Chipset GMAC 0x7a03 v3.50a/v3.73a 1
LS2K2000 SOC GMAC 0x7a03 v3.73a 8
LS2K2000 SOC GNET 0x7a13 v3.73a 8
LS7A2000 Chipset GNET 0x7a13 v3.73a 1
The driver currently supports the chips with the Loongson GMAC network
device synthesized with a single DMA-channel available. As a
preparation before adding the Loongson GNET support detach the
Loongson GMAC-specific platform data initializations to the
loongson_gmac_data() method and preserve the common settings in the
loongson_default_data().
While at it drop the return value statement from the
loongson_default_data() method as redundant.
Note there is no intermediate vendor-specific PCS in between the MAC
and PHY on Loongson GMAC and GNET. So the plat->mac_interface field
can be freely initialized with the PHY_INTERFACE_MODE_NA value.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
identification
For the readability sake convert the hard-coded Loongson GMAC PCI ID to
the respective macro and use the PCI_DEVICE_DATA() macro-function to
create the pci_device_id array entry. The later change will be
specifically useful in order to assign the device-specific data for the
currently supported device and for about to be added Loongson GNET
controller.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Loongson GMAC driver currently doesn't utilize the MSI IRQs, but
retrieves the IRQs specified in the device DT-node. Let's drop the
direct pci_enable_msi()/pci_disable_msi() calls then as redundant
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The plat_stmmacenet_data::multicast_filter_bins field is twice
initialized in the loongson_default_data() method. Drop the redundant
initialization, but for the readability sake keep the filters init
statements defined in the same place of the method.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Export the DW GMAC DMA-ops descriptor so one could be available in
the low-level platform drivers. It will be utilized to override some
callbacks in order to handle the LS2K2000 GNET device specifics. The
GNET controller support is being added in one of the following up
commits.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
DW GMAC v3.73 can be equipped with the Audio Video (AV) feature which
enables transmission of time-sensitive traffic over bridged local area
networks (DWC Ethernet QoS Product). In that case there can be up to two
additional DMA-channels available with no Tx COE support (unless there is
vendor-specific IP-core alterations). Each channel is implemented as a
separate Control and Status register (CSR) for managing the transmit and
receive functions, descriptor handling, and interrupt handling.
Add the multi-channels DW GMAC controllers support just by making sure the
already implemented DMA-configs are performed on the per-channel basis.
Note the only currently known instance of the multi-channel DW GMAC
IP-core is the LS2K2000 GNET controller, which has been released with the
vendor-specific feature extension of having eight DMA-channels. The device
support will be added in one of the following up commits.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ATDS (Alternate Descriptor Size) is a part of the DMA Bus Mode configs
(together with PBL, ALL, EME, etc) of the DW GMAC controllers. Seeing
it's not changed at runtime but is activated as long as the IP-core
has it supported (at least due to the Type 2 Full Checksum Offload
Engine feature), move the respective parameter from the
stmmac_dma_ops::init() callback argument to the stmmac_dma_cfg
structure, which already have the rest of the DMA-related configs
defined.
Besides the being added in the next commit DW GMAC multi-channels
support will require to add the stmmac_dma_ops::init_chan() callback
and have the ATDS flag set/cleared for each channel in there. Having
the atds-flag in the stmmac_dma_cfg structure will make the parameter
accessible from stmmac_dma_ops::init_chan() callback too.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fixup for "crypto: spacc - Add SPAcc Skcipher support"
interacting with commit
1a251f52cfdc ("minmax: make generic MIN() and MAX() macros available everywhere")
from Linus' tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reintroduced MIN macro with ifndef around it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
