| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes an issue where we were byte swapping the port
parameter, then byte swapping it again in function execution.
Obviously, that's unnecessary, so take it out of the function calls.
Without this patch, the udp based tunnel configuration would
not be correct.
Change-ID: I788d83c5bd5732170f1a81dbfa0b1ac3ca8ea5b7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes an issue in the virt channel code, where a return
from i40e_find_vsi_from_id was not checked for NULL when applicable.
Without this patch, there is a risk for panic and static analysis
tools complain. This patch fixes the problem by adding the check
and adding an additional input check for similar reasons.
Change-ID: I7e9be88eb7a3addb50eadc451c8336d9e06f5394
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This conditional is backward, so the driver responds back to the VF with
the wrong opcode. Do the old switcheroo to fix this.
Change-ID: I384035b0fef8a3881c176de4b4672009b3400b25
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When using the debugfs to issue the "dump port" command
with NPAR enabled, the firmware reports back with invalid argument.
The issue occurs because the pf->mac_seid was used to perform the query.
This is fine when NPAR is disabled because the switch ID == pf->mac_seid,
however this is not the case when NPAR is enabled. This fix instead
goes through the VSI to determine the correct ID to use in either case.
Change-ID: I0cd67913a7f2c4a2962e06d39e32e7447cc55b6a
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previously, when using ethtool to change the RSS hash key, ethtool would
report back saying the old key was still being used and no error was
reported. It was unclear whether it was being reported incorrectly or
being set incorrectly. Debugging revealed 'i40e_set_rxfh()' returned
zero immediately instead of setting the key because a user defined
indirection table is not supplied when changing the hash key.
This fix instead changes it such that if an indirection table is not
supplied, then a default one is created and the hash key is now
correctly set.
Change-ID: Iddb621897ecf208650272b7ee46702cad7b69a71
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Otherwise, nvme_rdma_stop_and_clear_queue() will incorrectly
try to stop/free rdma qps/cm_ids that are already freed.
Fixes: e89ca58f9c90 ("nvme-rdma: add DELETING queue flag")
Reported-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
PCIe hotplug supports optional Attention and Power Indicators, which are
used internally by pciehp. Users can't control the Power Indicator, but
they can control the Attention Indicator by writing to a sysfs "attention"
file.
The Slot Control register has two bits for each indicator, and the PCIe
spec defines the encodings for each as (Reserved/On/Blinking/Off). For
sysfs "attention" writes, pciehp_set_attention_status() maps into these
encodings, so the only useful write values are 0 (Off), 1 (On), and 2
(Blinking).
However, some platforms use all four bits for platform-specific indicators,
and they need to allow direct user control of them while preventing pciehp
from using them at all.
Add a "hotplug_user_indicators" flag to the pci_dev structure. When set,
pciehp does not use either the Attention Indicator or the Power Indicator,
and the low four bits (values 0x0 - 0xf) of sysfs "attention" write values
are written directly to the Attention Indicator Control and Power Indicator
Control fields.
[bhelgaas: changelog, rename flag and accessors to s/attention/indicator/]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Original commit, which added support for Armada CP110 system controller
used global variables for storing all clock information. It worked
fine for Armada 7k SoC, with single CP110 block. After dual-CP110 Armada 8k
was introduced, the data got overwritten and corrupted.
This patch fixes the issue by allocating resources dynamically in the
driver probe and storing it as platform drvdata.
Fixes: d3da3eaef7f4 ("clk: mvebu: new driver for Armada CP110 system ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Armada CP110 system controller comprises its own routine responsble
for registering gate clocks. Among others 'flags' field in
struct clk_init_data was not set, using a random values, which
may cause an unpredicted behavior.
This patch fixes the problem by resetting all fields of clk_init_data
before assigning values for all gated clocks of Armada 7k/8k SoCs family.
Fixes: d3da3eaef7f4 ("clk: mvebu: new driver for Armada CP110 system ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Fixes the following sparse warning:
drivers/gpu/drm/tilcdc/tilcdc_drv.c:64:5: warning:
symbol 'tilcdc_atomic_check' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
We get 3 warnings when building kernel with W=1:
drivers/gpu/drm/tilcdc/tilcdc_slave_compat.c:142:29: warning: no previous prototype for 'tilcdc_get_overlay' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_slave_compat.c:198:13: warning: no previous prototype for 'tilcdc_convert_slave_node' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_slave_compat.c:264:12: warning: no previous prototype for 'tilcdc_slave_compat_init' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
We get 4 warnings when building kernel with W=1:
drivers/gpu/drm/tilcdc/tilcdc_tfp410.c:393:12: warning: no previous prototype for 'tilcdc_tfp410_init' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_tfp410.c:398:13: warning: no previous prototype for 'tilcdc_tfp410_fini' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_panel.c:443:12: warning: no previous prototype for 'tilcdc_panel_init' [-Wmissing-prototypes]
drivers/gpu/drm/tilcdc/tilcdc_panel.c:448:13: warning: no previous prototype for 'tilcdc_panel_fini' [-Wmissing-prototypes]
In fact, these functions are declared in
drivers/gpu/drm/tilcdc/tilcdc_tfp410.h,
drivers/gpu/drm/tilcdc/tilcdc_panel.h,
so this patch adds missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
into irq/core
Pull irqchip core changes for v4.9 from Jason Cooper
- jcore: Add AIC driver
- mips-gic: Use for_each_set_bit
- mvebu: Add PIC driver
|
|
The upper bound IWL_RATE_COUNT_LEGACY should be used
with a >= check, rejecting the value itself; fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We were assigning the return value of iwl_mvm_ctdp_command() to a
variable, but never checking it. If this command fails, we should not
allow the interface up process to proceed, since it is potentially
dangerous to ignore thermal management requirements.
Fixes: commit 5c89e7bc557e ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The various TFD/TB helpers have two code paths depending on the
type of TFD supported, with variable shadowing due to the new if
branches. Move the fall-through code into else branches to avoid
variable shadowing. While doing so, rename some of the variables
and do some other cleanups (like removing void * casts of void *
pointers.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add two new PCI IDs for the 9560 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Move the init_dbg check to earlier in the function to simplify the
code.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Running with KASAN produces some messages:
BUG: KASAN: use-after-free in ti_st_send_frame+0x9c/0x16c at addr
ffffffc064868fe8
Read of size 1 by task kworker/u17:1/1266
<KASAN output trimmed>
Hardware name: HiKey Development Board (DT)
Workqueue: hci0 hci_cmd_work
Call trace:
[<ffffffc00008c00c>] dump_backtrace+0x0/0x178
[<ffffffc00008c1a4>] show_stack+0x20/0x28
[<ffffffc00067da38>] dump_stack+0xa8/0xe0
[<ffffffc000288430>] print_trailer+0x110/0x174
[<ffffffc00028aedc>] object_err+0x4c/0x5c
[<ffffffc00028f714>] kasan_report_error+0x254/0x54c
[<ffffffc00028fa70>] kasan_report+0x64/0x70
[<ffffffc00028eb8c>] __asan_load1+0x4c/0x54
[<ffffffc000b59b24>] ti_st_send_frame+0x9c/0x16c
[<ffffffc000ee8dcc>] hci_send_frame+0xb4/0x118
[<ffffffc000ee8efc>] hci_cmd_work+0xcc/0x154
[<ffffffc0000f6c48>] process_one_work+0x26c/0x7a4
[<ffffffc0000f721c>] worker_thread+0x9c/0x73c
[<ffffffc000100250>] kthread+0x138/0x154
[<ffffffc000085c50>] ret_from_fork+0x10/0x40
The packet is being accessed for statistics after it has been freed.
Save the packet type before sending for statistics afterwards.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This is never really used anymore.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
v2: minor build fix
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:
WARNING: CPU: 3 PID: 1593 at drivers/clk/clk.c:476 clk_core_unprepare+0x80/0x90
Modules linked in:
CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
clk_core_unprepare+0x80/0x90
qup_i2c_disable_clocks+0x2c/0x68
qup_i2c_suspend+0x10/0x20
platform_pm_suspend+0x24/0x68
...
This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
This patch fixs the following warning:
drivers/i2c/busses/i2c-rk3x.c: In function 'rk3x_i2c_v1_calc_timings':
drivers/i2c/busses/i2c-rk3x.c:745:41: warning: variable 'min_total_ns' set but not used [-Wunused-but-set-variable]
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch fixes the following sparse warning:
drivers/i2c/busses/i2c-rk3x.c:888:17: warning: cast truncates bits from constant value (ffffffffff00 becomes ffffff00)
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When enumerating I2C devices connected to an I2C adapter we scan the whole
namespace (as it is possible to have devices anywhere in that namespace,
not just below the I2C adapter device) and add each found device to the I2C
bus in question.
Now after commit 525e6fabeae2 ("i2c / ACPI: add support for ACPI
reconfigure notifications") checking of the adapter handle to the one found
in the I2cSerialBus() resource was moved to happen after resources of the
I2C device has been parsed. This means that if the I2cSerialBus() resource
points to an adapter that does not exists in the system we still parse
those resources. This is problematic in particular because
acpi_dev_resource_interrupt() tries to configure GSI if the device also has
an Interrupt() resource. Failing to do that results errrors like this to be
printed on the console:
[ 10.409490] ERROR: Unable to locate IOAPIC for GSI 37
To fix this we pass the I2C adapter to i2c_acpi_get_info() and make sure
the handle matches the one in the I2cSerialBus() resource before doing
anything else to the device.
Reported-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Fixes this smatch warning:
drivers/media/usb/ttusb-dec/ttusb_dec.c:243 ttusb_dec_handle_irq() error: buffer overflow 'rc_keys' 26 <= 126
As the RC keys should be enabled previously, via:
set_bit(rc_keys[i], input_dev->keybit);
It wouldn't go past the buffer in practice. Yet, as bad
things may happen when going past buffer, it doesn't hurt adding
a check here.
While here, fix CodingStyle issues on the routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Removes division from vblank_wait for DCE v6, v8,
and v10. Was already implemented for v11.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Make sure that it won't go past the config buffers
drivers/media/pci/cx23885/cx23885-dvb.c:1733 dvb_register() warn: buffer overflow 'netup_xc5000_config' 2 <= s32max
drivers/media/pci/cx23885/cx23885-dvb.c:1745 dvb_register() warn: buffer overflow 'netup_stv0367_config' 2 <= s32max
drivers/media/pci/cx23885/cx23885-dvb.c:1752 dvb_register() warn: buffer overflow 'netup_xc5000_config' 2 <= s32max
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- several fixes for new drivers added for Kernel 4.8 addition (cec
core, pulse8 cec driver and Mediatek vcodec)
- a regression fix for cx23885 and saa7134 drivers
- an important fix for rcar-fcp, making rcar_fcp_enable() return 0 on
success
* tag 'media/v4.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (25 commits)
[media] cx23885/saa7134: assign q->dev to the PCI device
[media] rcar-fcp: Make sure rcar_fcp_enable() returns 0 on success
[media] cec: fix ioctl return code when not registered
[media] cec: don't Feature Abort broadcast msgs when unregistered
[media] vcodec:mediatek: Refine VP8 encoder driver
[media] vcodec:mediatek: Refine H264 encoder driver
[media] vcodec:mediatek: change H264 profile default to profile high
[media] vcodec:mediatek: Add timestamp and timecode copy for V4L2 Encoder
[media] vcodec:mediatek: Fix visible_height larger than coded_height issue in s_fmt_out
[media] vcodec:mediatek: Fix fops_vcodec_release flow for V4L2 Encoder
[media] vcodec:mediatek:code refine for v4l2 Encoder driver
[media] cec-funcs.h: add missing vendor-specific messages
[media] cec-edid: check for IEEE identifier
[media] pulse8-cec: fix error handling
[media] pulse8-cec: set correct Signal Free Time
[media] mtk-vcodec: add HAS_DMA dependency
[media] cec: ignore messages when log_addr_mask == 0
[media] cec: add item to TODO
[media] cec: set unclaimed addresses to CEC_LOG_ADDR_INVALID
[media] cec: add CEC_LOG_ADDRS_FL_ALLOW_UNREG_FALLBACK flag
...
|
|
This avoids some low-level operations.
It has the benefit that now register values van be read from /sys/kernel/debug/regmap
The maximum register value is just a guess - all higher addresses read as zero.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Now that there is a i2c_client, use the more specific dev for logging.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Now that all users of legacy attach are converted it can be removed.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use new style attach.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
cx231xx does not yet support attaching new-style i2c_client DVB demod
drivers. Add necessary code base on tuner support for i2c_client.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use new style attach.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Afterwards it is possible to convert attaching in card drivers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When si2165_init fails, the clk values in state are still at zero.
But the dvb-core ignores the return value of init will call tune
afterwards.
This will trigger a division by zero when tuning.
At least check for the variables to be non-zero before dividing.
This happened for a system with WinTV HVR-4400 PCIe-card after suspend-to-disk.
Do suspend-to-disk without accessing the DVB device before.
After wakeup try to tune.
si2165_init fails at checking the chip_mode and aborts.
Then si2165_set_if_freq_shift will fail with div-by-zero.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Such fallback string is present in the 'soc_camera' version of the R-Car VIN
driver, so need to add it here as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
inside lgdt3306a_search we reading demod status 20 times with 50 msec sleep after each read.
This gives us more than 1 sec of delay. Removing this delay should not affect demod functionality.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Acked-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The workqueue "_irq_audio_queues" runs the audio upstream handler.
It has a single work item(&dev->_audio_work_entry) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
The work item has been flushed in cx25821_stop_upstream_audio() to ensure
that nothing is pending when the driver is disconnected.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Pull networking fixes from David Miller:
"Mostly small bits scattered all over the place, which is usually how
things go this late in the -rc series.
1) Proper driver init device resets in bnx2, from Baoquan He.
2) Fix accounting overflow in __tcp_retransmit_skb(),
sk_forward_alloc, and ip_idents_reserve, from Eric Dumazet.
3) Fix crash in bna driver ethtool stats handling, from Ivan Vecera.
4) Missing check of skb_linearize() return value in mac80211, from
Johannes Berg.
5) Endianness fix in nf_table_trace dumps, from Liping Zhang.
6) SSN comparison fix in SCTP, from Marcelo Ricardo Leitner.
7) Update DSA and b44 MAINTAINERS entries.
8) Make input path of vti6 driver work again, from Nicolas Dichtel.
9) Off-by-one in mlx4, from Sebastian Ott.
10) Fix fallback route lookup handling in ipv6, from Vincent Bernat.
11) Fix stack corruption on probe in qed driver, from Yuval Mintz.
12) PHY init fixes in r8152 from Hayes Wang.
13) Missing SKB free in irda_accept error path, from Phil Turnbull"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: properly account Fast Open SYN-ACK retrans
tcp: fix under-accounting retransmit SNMP counters
MAINTAINERS: Update b44 maintainer.
net: get rid of an signed integer overflow in ip_idents_reserve()
net/mlx4_core: Fix to clean devlink resources
net: can: ifi: Configure transmitter delay
vti6: fix input path
ipmr, ip6mr: return lastuse relative to now
r8152: disable ALDPS and EEE before setting PHY
r8152: remove r8153_enable_eee
r8152: move PHY settings to hw_phy_cfg
r8152: move enabling PHY
r8152: move some functions
cxgb4/cxgb4vf: Allocate more queues for 25G and 100G adapter
qed: Fix stack corruption on probe
MAINTAINERS: Add an entry for the core network DSA code
net: ipv6: fallback to full lookup if table lookup is unsuitable
net/mlx5: E-Switch, Handle mode change failures
net/mlx5: E-Switch, Fix error flow in the SRIOV e-switch init code
net/mlx5: Fix flow counter bulk command out mailbox allocation
...
|
|
Workqueues shouldn't be freed. destroy_workqueue should be used instead.
destroy_workqueue safely destroys a workqueue and ensures that all pending
work items are done before destroying the workqueue.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Signed-off-by: Harman Kalra <harman4linux@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
if specified DVB-C bandwidth not supported then force 8MHz.
Should work for most cases.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Replace BUG() with BUG_ON().
Caught by coccinelle.
Signed-off-by: Harman Kalra <harman4linux@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add these options as module parameters for now; should other drivers
need similar options we could add it to the LIRC api.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This is a duplicate of the timeout in rc_dev.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
BugLink: https://bugs.launchpad.net/bugs/1535802
T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3011 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
|
|
Added function to read BER for ISDB-T
Also SNR values fixed for ISDB-T
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Tha ARM randconfig builds came up with another rare build failure
for the dib3000mc driver, when dvb-usb-dibusb-mb is built-in and
dib3000mc is a loadable module:
ERROR: "dibusb_dib3000mc_frontend_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
ERROR: "dibusb_dib3000mc_tuner_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
Apparently this used to be a valid configuration (build-time, not
run-time), but broke as part of a cleanup.
I tried reverting the cleanup, but saw that the code was still wrong
then. This version adds a dependency for dib3000mb, to ensure that
dib3000mb does not force the dibusb_dib3000mc_frontend_attach function
to be built-in when dib3000mc is a loadable module.
I have also checked the two other files that were changed in the original
cleanup, and found them to be correct in either version, so I do not
touch that part.
As this is a rather obscure bug, there is no need for backports.
Fixes: 028c70ff42783 ("[media] dvb-usb/dvb-usb-v2: use IS_ENABLED")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
