| Age | Commit message (Collapse) | Author |
|---|
|
When adding a rule to a flow group we need increment the version of the
group. Current code fails to do that and as a result, when trying to add
a rule, we will fail to discover a case where an FTE with the same match
value was added while we scanned the groups of the same match criteria,
thus we may try to add an FTE that was already added.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Instead of using two different structs for searching groups with the
same match, use a single struct and thus simplify the code, make it more
readable and smaller size which means less code cache misses.
text data bss dec hex
before: 35524 2744 0 38268 957c
after: 35038 2744 0 37782 9396
When testing add 70000 rules, delete all the rules, and repeat three
times taking the average, we get (time in seconds):
Before the change: insert 16.80, delete 11.02
After the change: insert 16.55, delete 10.95
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The correct type is u32.
Fixes: d18296ffd9cc ("net/mlx5: E-Switch, Introduce global tables")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
We allocate a temporary memory but forget to free it.
Fixes: 11b717d61526 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Register c0 loopback is needed to fully support chains and prios.
Enable chains and prio only if loopback (of reg c1 which came together
with c0), is enabled. To be able to check that, move enabling of loopback
before eswitch chains init.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Reg c0/c1 matching, rewrite of regs c0/c1, and copy header of regs c1,B
is needed for the restore table to function, might not be supported by
firmware, and creation of the restore table or the copy header will
fail.
Check reg_c1 loopback support, as firmware which supports this,
should have all of the above.
Fixes: 11b717d61526 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The function mlx5e_rep_setup_ft_cb check chain_index is zero twice.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The actions_match_supported() function returns a bool, true for success
and false for failure. This error path is returning a negative which
is cast to true but it should return false.
Fixes: 4c3844d9e97e ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: 666aed2d13ee ("clk: imx: scu: add set parent support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/aad021e432b3062c142973d09b766656eec18fde.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: fe37b4820417 ("clk: imx: add scu clock common part")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/10e97a04980d933b2cfecb6b124bf9046b6e4f16.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Pull networking fixes from David Miller:
1) Fix deadlock in bpf_send_signal() from Yonghong Song.
2) Fix off by one in kTLS offload of mlx5, from Tariq Toukan.
3) Add missing locking in iwlwifi mvm code, from Avraham Stern.
4) Fix MSG_WAITALL handling in rxrpc, from David Howells.
5) Need to hold RTNL mutex in tcindex_partial_destroy_work(), from Cong
Wang.
6) Fix producer race condition in AF_PACKET, from Willem de Bruijn.
7) cls_route removes the wrong filter during change operations, from
Cong Wang.
8) Reject unrecognized request flags in ethtool netlink code, from
Michal Kubecek.
9) Need to keep MAC in reset until PHY is up in bcmgenet driver, from
Doug Berger.
10) Don't leak ct zone template in act_ct during replace, from Paul
Blakey.
11) Fix flushing of offloaded netfilter flowtable flows, also from Paul
Blakey.
12) Fix throughput drop during tx backpressure in cxgb4, from Rahul
Lakkireddy.
13) Don't let a non-NULL skb->dev leave the TCP stack, from Eric
Dumazet.
14) TCP_QUEUE_SEQ socket option has to update tp->copied_seq as well,
also from Eric Dumazet.
15) Restrict macsec to ethernet devices, from Willem de Bruijn.
16) Fix reference leak in some ethtool *_SET handlers, from Michal
Kubecek.
17) Fix accidental disabling of MSI for some r8169 chips, from Heiner
Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (138 commits)
net: Fix CONFIG_NET_CLS_ACT=n and CONFIG_NFT_FWD_NETDEV={y, m} build
net: ena: Add PCI shutdown handler to allow safe kexec
selftests/net/forwarding: define libs as TEST_PROGS_EXTENDED
selftests/net: add missing tests to Makefile
r8169: re-enable MSI on RTL8168c
net: phy: mdio-bcm-unimac: Fix clock handling
cxgb4/ptp: pass the sign of offset delta in FW CMD
net: dsa: tag_8021q: replace dsa_8021q_remove_header with __skb_vlan_pop
net: cbs: Fix software cbs to consider packet sending time
net/mlx5e: Do not recover from a non-fatal syndrome
net/mlx5e: Fix ICOSQ recovery flow with Striding RQ
net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset
net/mlx5e: Enhance ICOSQ WQE info fields
net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure
selftests: netfilter: add nfqueue test case
netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
netfilter: nft_fwd_netdev: validate family and chain type
netfilter: nft_set_rbtree: Detect partial overlaps on insertion
netfilter: nft_set_rbtree: Introduce and use nft_rbtree_interval_start()
netfilter: nft_set_pipapo: Separate partial and complete overlap cases on insertion
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- One core quirk by myself to fix the .irq_disable() semantics when the
gpiolib core takes over this callback.
- The rest is an elaborate series of four patches fixing Intel laptop
ACPI wakeup quirks.
* tag 'gpio-v5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: acpi: Add quirk to ignore EC wakeups on HP x2 10 CHT + AXP288 model
gpiolib: acpi: Add quirk to ignore EC wakeups on HP x2 10 BYT + AXP288 model
gpiolib: acpi: Rework honor_wakeup option into an ignore_wake option
gpiolib: acpi: Correct comment for HP x2 10 honor_wakeup quirk
gpiolib: Fix irq_disable() semantics
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.6
Fourth, and last, set of fixes for v5.6. Just two important fixes to
iwlwifi regressions.
iwlwifi
* fix GEO_TX_POWER_LIMIT command on certain devices which caused
firmware to crash during initialisation
* add back device ids for three devices which were accidentally
removed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: bcfabee1afd99484 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: noreply@ellerman.id.au
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds support to catch any bits set in SGE_INT_CAUSE5 for Parity Errors.
F_ERR_T_RXCRC flag is used to ignore that particular bit as it is not considered as fatal.
So, we clear out the bit before looking for error.
This patch now read and report separately all three registers(Cause1, Cause2, Cause5).
Also, checks for errors if any.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Rahul Kundu <rahul.kundu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since set_rx_mode takes a mutex lock for sending mailbox
message to admin function to set the mode, moved logic
to a workqueue.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed an issue wherein while refilling receive buffers
for the last page allocated, recount is not being updated.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace list_for_each() with list_for_each_entry(), and
list_entry(head.next) with list_first_entry().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a device is configured in prio-queue mode to pin all traffic onto
a specific HW queue, treat this as a distinct variant of prio-queueing
instead of QETH_NO_PRIO_QUEUEING.
This corrects an error message from qeth_osa_set_output_queues() for
devices configured in such a mode.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return the correct errnos when .ndo_set_mac_address fails to set a new
MAC address.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since IQD devices complete (most of) their transmissions synchronously,
they don't offer TX completion IRQs and have no HW coalescing controls.
But we can fake the easy parts in SW, and give the user some control wrt
to how often the TX NAPI code should be triggered to process the TX
completions.
Having per-queue controls can in particular help the dedicated mcast
queue, as it likely benefits from different fine-tuning than what the
ucast queues need.
CC: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Count the number of TX doorbells we issue to the qdio layer.
Also count the number of actual frames in a TX buffer, and then
use this data along with the byte count during TX completion.
We'll make additional use of the frame count in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're down to a single bit flag for MAC-address related status, reflect
that in the info struct.
Also set up the flag during initialization instead of clearing it during
shutdown - one more little step towards unifying the shutdown code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic that deals with errors from qeth_l3_get_unique_id() is quite
complex: it sets card->unique_id to 0xfffe, additionally flags it as
UNIQUE_ID_NOT_BY_CARD and later takes this flag as cue to not propagate
card->unique_id to dev->dev_id. With dev->dev_id thus holding 0,
addrconf_ifid_eui48() applies its default behaviour.
Get rid of all the special bit masks, and just return the old uid in
case of an error. For the vast majority of cases this will be 0 (and so
we still get the desired default behaviour) - with the rare exception
where qeth_l3_get_unique_id() might have been called earlier but the
initialization then failed at a later point.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the support for polling drivers was initially added, it only
considered Input Queue 0. But as QDIO interrupts are actually for the
full device and not a single queue, this doesn't really fit for
configurations where multiple Input Queues are used.
Rework the qdio code so that interrupts for a polling driver are not
split up into actions for each queue. Instead deliver the interrupt as
a single event, and let the driver decide which queue needs what action.
When re-enabling the QDIO interrupt via qdio_start_irq(), this means
that the qdio code needs to
(1) put _all_ eligible queues back into a state where they raise IRQs,
(2) and afterwards check _all_ eligible queues for new work to bridge
the race window.
On the qeth side of things (as the only qdio polling driver), we can now
add CQ polling support to the main NAPI poll routine. It doesn't consume
NAPI budget, and to avoid hogging the CPU we yield control after
completing one full queue worth of buffers.
The subsequent qdio_start_irq() will check for any additional work, and
have us re-schedule the NAPI instance accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whenever all completed RX buffers have been processed
(ie. rx->b_count == 0), we call down to the HW layer to scan for
additional buffers. If no further buffers are available, the code
breaks out of the while-loop.
So we never reach the 'process an RX buffer' step with rx->b_count == 0,
eliminate that check and one level of indentation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main NAPI poll routine should eventually handle more types of work,
beyond just the RX ring.
Split off the RX poll logic into a separate function, and simplify the
nested while-loop.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since RX buffers may contain multiple packets, qeth's NAPI poll code can
exhaust its budget in the middle of an RX buffer. Thus we keep track of
our current position within the active RX buffer, so we can resume
processing here in the next NAPI poll period.
Clean up that code by tracking the index of the active buffer element,
instead of a pointer to it.
Also simplify the code that advances to the next RX buffer when the
current buffer has been fully processed.
v2: - remove QDIO_ELEMENT_NO() macro (davem)
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently ENA only provides the PCI remove() handler, used during rmmod
for example. This is not called on shutdown/kexec path; we are potentially
creating a failure scenario on kexec:
(a) Kexec is triggered, no shutdown() / remove() handler is called for ENA;
instead pci_device_shutdown() clears the master bit of the PCI device,
stopping all DMA transactions;
(b) Kexec reboot happens and the device gets enabled again, likely having
its FW with that DMA transaction buffered; then it may trigger the (now
invalid) memory operation in the new kernel, corrupting kernel memory area.
This patch aims to prevent this, by implementing a shutdown() handler
quite similar to the remove() one - the difference being the handling
of the netdev, which is unregistered on remove(), but following the
convention observed in other drivers, it's only detached on shutdown().
This prevents an odd issue in AWS Nitro instances, in which after the 2nd
kexec the next one will fail with an initrd corruption, caused by a wild
DMA write to invalid kernel memory. The lspci output for the adapter
present in my instance is:
00:05.0 Ethernet controller [0200]: Amazon.com, Inc. Elastic Network
Adapter (ENA) [1d0f:ec20]
Suggested-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c: In function cxgb4_get_free_ftid:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c:547:23:
warning: variable tab set but not used [-Wunused-but-set-variable]
commit 8d174351f285 ("cxgb4: rework TC filter rule insertion across regions")
involved this, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calls to dma_map_sg may return less segments / entries than requested
if they fall on page bounderies. The old implementation did not
support this use case.
Fixes: be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206461
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206895
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1056
Signed-off-by: Shane Francis <bigbeeshane@gmail.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325090741.21957-4-bigbeeshane@gmail.com
Cc: stable@vger.kernel.org
|
|
Calls to dma_map_sg may return less segments / entries than requested
if they fall on page bounderies. The old implementation did not
support this use case.
Fixes: be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206461
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206895
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1056
Signed-off-by: Shane Francis <bigbeeshane@gmail.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325090741.21957-3-bigbeeshane@gmail.com
Cc: stable@vger.kernel.org
|
|
As dma_map_sg can reorganize scatter-gather lists in a
way that can cause some later segments to be empty we should
always use the sg_dma_len macro to fetch the actual length.
This could now be 0 and not need to be mapped to a page or
address array
Fixes: be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206461
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206895
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1056
Signed-off-by: Shane Francis <bigbeeshane@gmail.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325090741.21957-2-bigbeeshane@gmail.com
Cc: stable@vger.kernel.org
|
|
Correct the probe return value to -ENODEV on non-Exynos platforms.
Link: https://lore.kernel.org/r/20200316175652.5604-4-krzk@kernel.org
Fixes: 02fb29882d5c ("soc: samsung: chipid: Drop "syscon" compatible requirement")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
tee: amdtee: out of bounds read in find_session()
* tag 'tee-amdtee-fix2-for-5.6' of https://git.linaro.org/people/jens.wiklander/linux-tee:
tee: amdtee: out of bounds read in find_session()
Link: https://lore.kernel.org/r/20200320063446.GA9892@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few more fixes for omaps
Just few dts fixes:
- A fix droid4 touchscreen stopping working with lost gpio interrupts
- Also limit omap5 dma range similar to what we've recently done for dra7
* tag 'omap-for-v5.6/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: dts: N900: fix onenand timings
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
Link: https://lore.kernel.org/r/pull-1584575254-461940@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
It has been discovered that this feature can globally block the RX port,
so it should be allowed for highly privileged users only.
Fixes: 03404e8ae652("IB/mlx5: Add support to dropless RQ")
Link: https://lore.kernel.org/r/20200322124906.1173790-1-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for v5.6
A pretty normal set of fixes for v5.6:
- Fix reversed macros used for A83T EMAC clock and reset
- Fix camera regulator voltage and USB OTG for TBS-A711
- 16-bit / 8-bit mixed read fix for our RSB driver
- Fix SPI controller base address for R40
- Reorder device nodes based on base address for R40
* tag 'sunxi-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
bus: sunxi-rsb: Return correct data when mixing 16-bit and 8-bit reads
ARM: dts: sun8i-a83t-tbs-a711: Fix USB OTG mode detection
ARM: dts: sun8i-a83t-tbs-a711: HM5065 doesn't like such a high voltage
ARM: dts: sun8i: a83t: Fix incorrect clk and reset macros for EMAC device
Link: https://lore.kernel.org/r/20200313055233.GA19649@wens.csie.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/fixes
NXP/FSL soc driver fixes for v5.6
DPAA2 DPIO
- Fix a kernel hang caused by irq requested before creating dpio
* tag 'soc-fsl-fix-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: dpio: register dpio irq handlers after dpio create
Link: https://lore.kernel.org/r/20200312202525.16708-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Some USB bridge devices will return a default set of characteristics during
initialization. And then, once an attached drive has spun up, substitute
the actual parameters reported by the drive. According to the SCSI spec,
the device should return a UNIT ATTENTION in case any reported parameters
change. But in this case the change is made silently after a small window
where default values are reported.
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of
physical block size") validated the reported optimal I/O size against the
physical block size to overcome problems with devices reporting nonsensical
transfer sizes. However, this validation did not account for the fact that
aforementioned devices will return default values during a brief window
during spin-up. The subsequent change in reported characteristics would
invalidate the checking that had previously been performed.
Unset a previously configured optimal I/O size should the sanity checking
fail on subsequent revalidate attempts.
Link: https://lore.kernel.org/r/33fb522e-4f61-1b76-914f-c9e6a3553c9b@gmail.com
Cc: Bryan Gurney <bgurney@redhat.com>
Cc: <stable@vger.kernel.org>
Reported-by: Bernhard Sulzer <micraft.b@gmail.com>
Tested-by: Bernhard Sulzer <micraft.b@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-03-24
This series introduces some fixes to mlx5 driver.
From Aya, Fixes to the RX error recovery flows
From Leon, Fix IB capability mask
Please pull and let me know if there is any problem.
For -stable v5.5
('net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure')
For -stable v5.4
('net/mlx5e: Fix ICOSQ recovery flow with Striding RQ')
('net/mlx5e: Do not recover from a non-fatal syndrome')
('net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset')
('net/mlx5e: Enhance ICOSQ WQE info fields')
The above patch ('net/mlx5e: Enhance ICOSQ WQE info fields')
will fail to apply cleanly on v5.4 due to a trivial contextual conflict,
but it is an important fix, do I need to do something about it or just
assume Greg will know how to handle this ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839
Fixes: 003bd5b4a7b4 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DT binding for this PHY describes an *optional* clock property.
Due to a bug in the error handling logic, we are actually ignoring this
clock *all* of the time so far.
Fix this by using devm_clk_get_optional() to handle this clock properly.
Fixes: b78ac6ecd1b6b ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It looks like the VSC8584 PHY driver is rolling its own RGMII delay
configuration code, despite the fact that the logic is mostly the same.
In fact only the register layout and position for the RGMII controls has
changed. So we need to adapt and parameterize the PHY-dependent bit
fields when calling the new generic function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With all DMA address accesses wrapped, we can actually support 64-bit
DMA if this option was chosen at IP integration time.
If the IP has been configured for an address width greater than 32 bits,
we assume the full 64 bit DMA width is working. In practise this will be
limited by the actual system address bus width, which will ideally be the
same as the DMA IP address width.
If this is not the case, the actual width can still be configured using a
dma-ranges property in the parent of the MAC node.
This increases the DMA mask on those systems to let the kernel choose
buffers from memory at higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When newer revisions of the Axienet IP are configured for a 64-bit bus,
we *need* to write to the MSB part of the an address registers,
otherwise the IP won't recognise this as a DMA start condition.
This is even true when the actual DMA address comes from the lower 4 GB.
To autodetect this configuration, at probe time we write all 1's to such
an MSB register, and see if any bits stick. If this is configured for a
32-bit bus, those MSB registers are RES0, so reading back 0 indicates
that no MSB writes are necessary.
On the other hands reading anything other than 0 indicated the need to
write the MSB registers, so we set the respective flag.
The actual DMA mask stays at 32-bit for now. To help bisecting, a
separate patch will enable allocations from higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer revisions of the AXI DMA IP (>= v7.1) support 64-bit addresses,
both for the descriptors itself, as well as for the buffers they are
pointing to.
This is realised by adding "MSB" words for the next and phys pointer
right behind the existing address word, now named "LSB". These MSB words
live in formerly reserved areas of the descriptor.
If the hardware supports it, write both words when setting an address.
The buffer address is handled by two wrapper functions, the two
occasions where we set the next pointers are open coded.
For now this is guarded by a flag which we don't set yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer versions of the Xilink DMA IP support busses with more than 32
address bits, by introducing an MSB word for the registers holding DMA
pointers (tail/current, RX/TX descriptor addresses).
On IP configured for more than 32 bits, it is also *required* to write
both words, to let the IP recognise this as a start condition for an
MM2S request, for instance.
Wrap the DMA pointer writes with a separate function, to add this
functionality later. For now we stick to the lower 32 bits.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mii-tool is useful for debugging, and all it requires to work is to wire
up the ioctl ops function pointer.
Add this to the axienet driver to enable mii-tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
