| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-03-08
This series contains updates to iavf, i40e, and ice drivers.
Michal ensures netdev features are properly updated to reflect VLAN
changes received from PF and adds an additional flag for MSI-X
reinitialization as further differentiation of reinitialization
operations is needed for iavf.
Jake stops disabling of VFs due to failed virtchannel responses for
i40e and ice driver.
Dave moves MTU event notification to the service task to prevent issues
with RTNL lock for ice.
Christophe Jaillet corrects an allocation to GFP_ATOMIC instead of
GFP_KERNEL for ice.
Jedrzej fixes the value for link speed comparison which was preventing
the requested value from being set for ice.
---
Note: This will conflict when merging with net-next. Resolution:
diff --cc drivers/net/ethernet/intel/ice/ice.h
index dc42ff92dbad,3121f9b04f59..000000000000
--- a/drivers/net/ethernet/intel/ice/ice.h
+++ b/drivers/net/ethernet/intel/ice/ice.h
@@@ -484,10 -481,9 +484,11 @@@ enum ice_pf_flags
ICE_FLAG_LEGACY_RX,
ICE_FLAG_VF_TRUE_PROMISC_ENA,
ICE_FLAG_MDD_AUTO_RESET_VF,
+ ICE_FLAG_VF_VLAN_PRUNING,
ICE_FLAG_LINK_LENIENT_MODE_ENA,
ICE_FLAG_PLUG_AUX_DEV,
+ ICE_FLAG_MTU_CHANGED,
+ ICE_FLAG_GNSS, /* GNSS successfully initialized */
ICE_PF_FLAGS_NBITS /* must be last */
};
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. Calling of_node_put() to avoid the
refcount leak. As the remove function do.
Fixes: 5cdaaa12866e ("net: emaclite: adding MDIO and phy lib support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220308024751.2320-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change curr_link_speed advertised speed, due to
link_info.link_speed is not equal phy.curr_user_speed_req.
Without this patch it is impossible to set advertised
speed to same as link_speed.
Testing Hints: Try to set advertised speed
to 25G only with 25G default link (use ethtool -s 0x80000000)
Fixes: 48cb27f2fd18 ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_misc_intr() is an irq handler. It should not sleep.
Use GFP_ATOMIC instead of GFP_KERNEL when allocating some memory.
Fixes: 348048e724a0 ("ice: Implement iidc operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a bonded interface is destroyed, .ndo_change_mtu can be called
during the tear-down process while the RTNL lock is held. This is a
problem since the auxiliary driver linked to the LAN driver needs to be
notified of the MTU change, and this requires grabbing a device_lock on
the auxiliary_device's dev. Currently this is being attempted in the
same execution context as the call to .ndo_change_mtu which is causing a
dead-lock.
Move the notification of the changed MTU to a separate execution context
(watchdog service task) and eliminate the "before" notification.
Fixes: 348048e724a0e ("ice: Implement iidc operations")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_send_msg_to_vf function has logic to detect "failure"
responses being sent to a VF. If a VF is sent more than
ICE_DFLT_NUM_INVAL_MSGS_ALLOWED then the VF is marked as disabled.
Almost identical logic also existed in the i40e driver.
This logic was added to the ice driver in commit 1071a8358a28 ("ice:
Implement virtchnl commands for AVF support") which itself copied from
the i40e implementation in commit 5c3c48ac6bf5 ("i40e: implement virtual
device interface").
Neither commit provides a proper explanation or justification of the
check. In fact, later commits to i40e changed the logic to allow
bypassing the check in some specific instances.
The "logic" for this seems to be that error responses somehow indicate a
malicious VF. This is not really true. The PF might be sending an error
for any number of reasons such as lack of resources, etc.
Additionally, this causes the PF to log an info message for every failed
VF response which may confuse users, and can spam the kernel log.
This behavior is not documented as part of any requirement for our
products and other operating system drivers such as the FreeBSD
implementation of our drivers do not include this type of check.
In fact, the change from dev_err to dev_info in i40e commit 18b7af57d9c1
("i40e: Lower some message levels") explains that these messages
typically don't actually indicate a real issue. It is quite likely that
a user who hits this in practice will be very confused as the VF will be
disabled without an obvious way to recover.
We already have robust malicious driver detection logic using actual
hardware detection mechanisms that detect and prevent invalid device
usage. Remove the logic since its not a documented requirement and the
behavior is not intuitive.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The i40e_vc_send_msg_to_vf_ex (and its wrapper i40e_vc_send_msg_to_vf)
function has logic to detect "failure" responses sent to the VF. If a VF
is sent more than I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED, then the VF is
marked as disabled. In either case, a dev_info message is printed
stating that a VF opcode failed.
This logic originates from the early implementation of VF support in
commit 5c3c48ac6bf5 ("i40e: implement virtual device interface").
That commit did not go far enough. The "logic" for this behavior seems
to be that error responses somehow indicate a malicious VF. This is not
really true. The PF might be sending an error for any number of reasons
such as lacking resources, an unsupported operation, etc. This does not
indicate a malicious VF. We already have a separate robust malicious VF
detection which relies on hardware logic to detect and prevent a variety
of behaviors.
There is no justification for this behavior in the original
implementation. In fact, a later commit 18b7af57d9c1 ("i40e: Lower some
message levels") reduced the opcode failure message from a dev_err to a
dev_info. In addition, recent commit 01cbf50877e6 ("i40e: Fix to not
show opcode msg on unsuccessful VF MAC change") changed the logic to
allow quieting it for expected failures.
That commit prevented this logic from kicking in for specific
circumstances. This change did not go far enough. The behavior is not
documented nor is it part of any requirement for our products. Other
operating systems such as the FreeBSD implementation of our driver do
not include this logic.
It is clear this check does not make sense, and causes problems which
led to ugly workarounds.
Fix this by just removing the entire logic and the need for the
i40e_vc_send_msg_to_vf_ex function.
Fixes: 01cbf50877e6 ("i40e: Fix to not show opcode msg on unsuccessful VF MAC change")
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In some cases overloaded flag IAVF_FLAG_REINIT_ITR_NEEDED
which should indicate that interrupts need to be completely
reinitialized during reset leads to RTNL deadlocks using ethtool -C
while a reset is in progress.
To fix, it was added a new flag IAVF_FLAG_REINIT_MSIX_NEEDED
used to trigger MSI-X reinit.
New combined setting is fixed adopt after VF reset.
This has been implemented by call reinit interrupt scheme
during VF reset.
Without this fix new combined setting has never been adopted.
Fixes: 209f2f9c7181 ("iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 negotiation")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Modify netdev->features for vlan stripping based on virtual
channel messages received from the PF. Change is needed
to synchronize vlan strip status between PF sysfs and iavf ethtool.
Fixes: 5951a2b9812d ("iavf: Fix VLAN feature flags after VFR")
Signed-off-by: Norbert Ciosek <norbertx.ciosek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
max_seg_size is unsigned int and it can have a value up to 2^32
(for eg:-RZ_DMAC driver sets dma_set_max_seg_size as U32_MAX)
When this value is used in min_t() as an integer type, it becomes
-1 and the value of sgs becomes 0.
Fix this issue by replacing the 'int' data type with 'unsigned int'
in min_t().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220307184843.9994-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Discussing one of the tests in mt753x_phylink_validate() with Landen
Chao confirms that the "||" should be "&&". Fix this.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1nRCF0-00CiXD-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It turns out that DE3 manual has inverted YUV and YVU format numbers for
P010 and P210. Invert them.
This was tested by playing video decoded to P010 and additionally
confirmed by looking at BSP driver source.
Fixes: 169ca4b38932 ("drm/sun4i: Add separate DE3 VI layer formats")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228181436.1424550-1-jernej.skrabec@gmail.com
|
|
Compiler is not happy:
warning: symbol 'gpio_sim_hog_config_item_ops' was not declared. Should it be static?
Fixes: cb8c474e79be ("gpio: sim: new testing module")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Use Krzysztof Kozlowski's @kernel.org account in maintainer entries.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220307172805.156760-1-krzysztof.kozlowski@canonical.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fix from Miquel Raynal:
"As part of a previous changeset introducing support for the K3
architecture, the OMAP_GPMC (a non visible symbol) got selected by the
selection of MTD_NAND_OMAP2 instead of doing so from the architecture
directly (like for the other users of these two drivers). Indeed, from
a hardware perspective, the OMAP NAND controller needs the GPMC to
work.
This led to a robot error which got addressed in fix merge into -rc4.
Unfortunately, the approach at this time still used "select" and lead
to further build error reports (sparc64:allmodconfig).
This time we switch to 'depends on' in order to prevent random
misconfigurations. The different dependencies will however need a
future cleanup"
* tag 'mtd/fixes-for-5.17-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: omap2: Actually prevent invalid configuration and build error
|
|
Pull virtio fixes from Michael Tsirkin:
"Some last minute fixes that took a while to get ready. Not
regressions, but they look safe and seem to be worth to have"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: handle fallout from folio work
tools/virtio: fix virtio_test execution
vhost: remove avail_event arg from vhost_update_avail_event()
virtio: drop default for virtio-mem
vdpa: fix use-after-free on vp_vdpa_remove
virtio-blk: Remove BUG_ON() in virtio_queue_rq()
virtio-blk: Don't use MAX_DISCARD_SEGMENTS if max_discard_seg is zero
vhost: fix hung thread due to erroneous iotlb entries
vduse: Fix returning wrong type in vduse_domain_alloc_iova()
vdpa/mlx5: add validation for VIRTIO_NET_CTRL_MQ_VQ_PAIRS_SET command
vdpa/mlx5: should verify CTRL_VQ feature exists for MQ
vdpa: factor out vdpa_set_features_unlocked for vdpa internal use
virtio_console: break out of buf poll on remove
virtio: document virtio_reset_device
virtio: acknowledge all features before access
virtio: unexport virtio_finalize_features
|
|
The root of the problem is that we are selecting symbols that have
dependencies. This can cause random configurations that can fail.
The cleanest solution is to avoid using select.
This driver uses interfaces from the OMAP_GPMC driver so we have to
depend on it instead.
Fixes: 4cd335dae3cf ("mtd: rawnand: omap2: Prevent invalid configuration and build error")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/linux-mtd/20220219193600.24892-1-rogerq@kernel.org
|
|
Currently we are observing occasional screen flickering when
PSR2 selective fetch is enabled. More specifically glitch seems
to happen on full frame update when cursor moves to coords
x = -1 or y = -1.
According to Bspec SF Single full frame should not be set if
SF Partial Frame Enable is not set. This happened to be true for
ADLP as PSR2_MAN_TRK_CTL_ENABLE is always set and for ADL_P it's
actually "SF Partial Frame Enable" (Bit 31).
Setting "SF Partial Frame Enable" bit also on full update seems to
fix screen flickering.
Also make code more clear by setting PSR2_MAN_TRK_CTL_ENABLE
only if not on ADL_P. Bit 31 has different meaning in ADL_P.
Bspec: 49274
v2: Fix Mihai Harpau email address
v3: Modify commit message and remove unnecessary comment
Tested-by: Lyude Paul <lyude@redhat.com>
Fixes: 7f6002e58025 ("drm/i915/display: Enable PSR2 selective fetch by default")
Reported-by: Lyude Paul <lyude@redhat.com>
Cc: Mihai Harpau <mharpau@gmail.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/5077
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225070228.855138-1-jouni.hogander@intel.com
(cherry picked from commit 8d5516d18b323cf7274d1cf5fe76f4a691f879c6)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
It appears that GPIO ACPI library uses ACPI debounce values directly.
However, the GPIO library APIs expect the debounce timeout to be in
microseconds.
Convert ACPI value of debounce to microseconds.
While at it, document this detail where it is appropriate.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215664
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Fixes: 8dcb7a15a585 ("gpiolib: acpi: Take into account debounce settings")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Some GPIO lines have stopped working after the patch
commit 2ab73c6d8323f ("gpio: Support GPIO controllers without pin-ranges")
And this has supposedly been fixed in the following patches
commit 89ad556b7f96a ("gpio: Avoid using pin ranges with !PINCTRL")
commit 6dbbf84603961 ("gpiolib: Don't free if pin ranges are not defined")
But an erratic behavior where some GPIO lines work while others do not work
has been introduced.
This patch reverts those changes so that the sysfs-gpio interface works
properly again.
Signed-off-by: Marcelo Roberto Jimenez <marcelo.jimenez@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Add the number of interrupts per bank for Tegra241 (Grace) to
fix the probe failure.
Fixes: d1056b771ddb ("gpio: tegra186: Add support for Tegra241")
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
According to Documentation/driver-api/usb/URB.rst when a device
is unplugged usb_submit_urb() returns -ENODEV.
This error code propagates all the way up to usbnet_read_cmd() and
usbnet_write_cmd() calls inside the smsc95xx.c driver during
Ethernet cable unplug, unbind or reboot.
This causes the following errors to be shown on reboot, for example:
ci_hdrc ci_hdrc.1: remove, state 1
usb usb2: USB disconnect, device number 1
usb 2-1: USB disconnect, device number 2
usb 2-1.1: USB disconnect, device number 3
smsc95xx 2-1.1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: hardware isn't capable of remote wakeup
usb 2-1.4: USB disconnect, device number 4
ci_hdrc ci_hdrc.1: USB bus 2 deregistered
ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot!
reboot: Restarting system
Ignore the -ENODEV errors inside __smsc95xx_mdio_read() and
__smsc95xx_phy_wait_not_busy() and do not print error messages
when -ENODEV is returned.
Fixes: a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang static analysis reports this issue
qed_sriov.c:4727:19: warning: Assigned value is
garbage or undefined
ivi->max_tx_rate = tx_rate ? tx_rate : link.speed;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
link is only sometimes set by the call to qed_iov_get_link()
qed_iov_get_link fails without setting link or returning
status. So change the decl to return status.
Fixes: 73390ac9d82b ("qed*: support ndo_get_vf_config")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver fails to register net device, it should free the DMA
region first, and then do other cleanup.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb->len field is read after the packet is sent to the network
stack. In the meantime, skb can be freed. This patch fixes this bug.
Fixes: c3e6b2c35b34 ("net: lantiq_xrx200: add ingress SG DMA support")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qed_vf_hw_prepare()
The function dma_alloc_coherent() in qed_vf_hw_prepare() can fail, so
its return value should be checked.
Fixes: 1408cc1fa48c ("qed: Introduce VFs")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function dma_set_mask() in setup_hw() can fail, so its return value
should be checked.
Fixes: 1700fe1a10dc ("Add mISDN HFC PCI driver")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1"),
significantly decreased the polling period from ~10-12ms into just a couple
of us. The purpose was to decrease the total time spent in the busy polling
loop, but unfortunate it has lead to problems, that causes eMMC cards to
never gets out busy and thus fails to be initialized.
To fix the problem, but also to try to keep some of the new improved
behaviour, let's start by using a polling period of 1-2ms, which then
increases for each loop, according to common polling loop in
__mmc_poll_for_busy().
Reported-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Huijin Park <huijin.park@samsung.com>
Fixes: 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/20220304105656.149281-1-ulf.hansson@linaro.org
|
|
When calling gnttab_end_foreign_access_ref() the returned value must
be tested and the reaction to that value should be appropriate.
In case of failure in xennet_get_responses() the reaction should not be
to crash the system, but to disable the network device.
The calls in setup_netfront() can be replaced by calls of
gnttab_end_foreign_access(). While at it avoid double free of ring
pages and grant references via xennet_disconnect_backend() in this case.
This is CVE-2022-23042 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V2:
- avoid double free
V3:
- remove pointless initializer (Jan Beulich)
|
|
gnttab_end_foreign_access() is used to free a grant reference and
optionally to free the associated page. In case the grant is still in
use by the other side processing is being deferred. This leads to a
problem in case no page to be freed is specified by the caller: the
caller doesn't know that the page is still mapped by the other side
and thus should not be used for other purposes.
The correct way to handle this situation is to take an additional
reference to the granted page in case handling is being deferred and
to drop that reference when the grant reference could be freed
finally.
This requires that there are no users of gnttab_end_foreign_access()
left directly repurposing the granted page after the call, as this
might result in clobbered data or information leaks via the not yet
freed grant reference.
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <simon@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V4:
- expand comment in header
V5:
- get page ref in case of kmalloc() failure, too
|
|
Instead of __get_free_pages() and free_pages() use alloc_pages_exact()
and free_pages_exact(). This is in preparation of a change of
gnttab_end_foreign_access() which will prohibit use of high-order
pages.
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <simon@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V4:
- new patch
|
|
The usage of gnttab_end_foreign_access() in xenhcd_gnttab_done() is
not safe against a malicious backend, as the backend could keep the
I/O page mapped and modify it even after the granted memory page is
being used for completely other purposes in the local system.
So replace that use case with gnttab_try_end_foreign_access() and
disable the PV host adapter in case the backend didn't stop using the
granted page.
In xenhcd_urb_request_done() immediately return in case of setting
the device state to "error" instead of looking into further backend
responses.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V2:
- use gnttab_try_end_foreign_access()
|
|
Remove gnttab_query_foreign_access(), as it is unused and unsafe to
use.
All previous use cases assumed a grant would not be in use after
gnttab_query_foreign_access() returned 0. This information is useless
in best case, as it only refers to a situation in the past, which could
have changed already.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
|
|
Using gnttab_query_foreign_access() is unsafe, as it is racy by design.
The use case in the gntalloc driver is not needed at all. While at it
replace the call of gnttab_end_foreign_access_ref() with a call of
gnttab_end_foreign_access(), which is what is really wanted there. In
case the grant wasn't used due to an allocation failure, just free the
grant via gnttab_free_grant_reference().
This is CVE-2022-23039 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V3:
- fix __del_gref() (Jan Beulich)
|
|
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_try_end_foreign_access() and check the
success of that operation instead.
This is CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V2:
- use gnttab_try_end_foreign_access()
|
|
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_end_foreign_access_ref() and check the
success of that operation instead.
This is CVE-2022-23037 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V2:
- use gnttab_try_end_foreign_access()
V3:
- don't use gnttab_try_end_foreign_access()
|
|
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_end_foreign_access_ref() and check the
success of that operation instead.
For the ring allocation use alloc_pages_exact() in order to avoid
high order pages in case of a multi-page ring.
If a grant wasn't unmapped by the backend without persistent grants
being used, set the device state to "error".
This is CVE-2022-23036 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
---
V2:
- use gnttab_try_end_foreign_access()
V4:
- use alloc_pages_exact() and free_pages_exact()
- set state to error if backend didn't unmap (Roger Pau Monné)
|
|
Add a new grant table function gnttab_try_end_foreign_access(), which
will remove and free a grant if it is not in use.
Its main use case is to either free a grant if it is no longer in use,
or to take some other action if it is still in use. This other action
can be an error exit, or (e.g. in the case of blkfront persistent grant
feature) some special handling.
This is CVE-2022-23036, CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V2:
- new patch
V4:
- add comments to header (Jan Beulich)
|
|
Letting xenbus_grant_ring() tear down grants in the error case is
problematic, as the other side could already have used these grants.
Calling gnttab_end_foreign_access_ref() without checking success is
resulting in an unclear situation for any caller of xenbus_grant_ring()
as in the error case the memory pages of the ring page might be
partially mapped. Freeing them would risk unwanted foreign access to
them, while not freeing them would leak memory.
In order to remove the need to undo any gnttab_grant_foreign_access()
calls, use gnttab_alloc_grant_references() to make sure no further
error can occur in the loop granting access to the ring pages.
It should be noted that this way of handling removes leaking of
grant entries in the error case, too.
This is CVE-2022-23040 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
|
|
In vhost_update_avail_event() we never used the `avail_event` argument,
since its introduction in commit 2723feaa8ec6 ("vhost: set log when
updating used flags or avail event").
Let's remove it to clean up the code.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20220113141134.186773-1-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
There's no special reason why virtio-mem needs a default that's
different from what kconfig provides, any more than e.g. virtio blk.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
|
|
When vp_vdpa driver is unbind, vp_vdpa is freed in vdpa_unregister_device
and then vp_vdpa->mdev.pci_dev is dereferenced in vp_modern_remove,
triggering use-after-free.
Call Trace of unbinding driver free vp_vdpa :
do_syscall_64
vfs_write
kernfs_fop_write_iter
device_release_driver_internal
pci_device_remove
vp_vdpa_remove
vdpa_unregister_device
kobject_release
device_release
kfree
Call Trace of dereference vp_vdpa->mdev.pci_dev:
vp_modern_remove
pci_release_selected_regions
pci_release_region
pci_resource_len
pci_resource_end
(dev)->resource[(bar)].end
Signed-off-by: Zhang Min <zhang.min9@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Link: https://lore.kernel.org/r/20220301091059.46869-1-wang.yi59@zte.com.cn
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: 64b9f64f80a6 ("vdpa: introduce virtio pci driver")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
|
|
Currently we have a BUG_ON() to make sure the number of sg
list does not exceed queue_max_segments() in virtio_queue_rq().
However, the block layer uses queue_max_discard_segments()
instead of queue_max_segments() to limit the sg list for
discard requests. So the BUG_ON() might be triggered if
virtio-blk device reports a larger value for max discard
segment than queue_max_segments(). To fix it, let's simply
remove the BUG_ON() which has become unnecessary after commit
02746e26c39e("virtio-blk: avoid preallocating big SGL for data").
And the unused vblk->sg_elems can also be removed together.
Fixes: 1f23816b8eb8 ("virtio_blk: add discard and write zeroes support")
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Link: https://lore.kernel.org/r/20220304100058.116-2-xieyongji@bytedance.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Currently the value of max_discard_segment will be set to
MAX_DISCARD_SEGMENTS (256) with no basis in hardware if device
set 0 to max_discard_seg in configuration space. It's incorrect
since the device might not be able to handle such large descriptors.
To fix it, let's follow max_segments restrictions in this case.
Fixes: 1f23816b8eb8 ("virtio_blk: add discard and write zeroes support")
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Link: https://lore.kernel.org/r/20220304100058.116-1-xieyongji@bytedance.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
In vhost_iotlb_add_range_ctx(), range size can overflow to 0 when
start is 0 and last is ULONG_MAX. One instance where it can happen
is when userspace sends an IOTLB message with iova=size=uaddr=0
(vhost_process_iotlb_msg). So, an entry with size = 0, start = 0,
last = ULONG_MAX ends up in the iotlb. Next time a packet is sent,
iotlb_access_ok() loops indefinitely due to that erroneous entry.
Call Trace:
<TASK>
iotlb_access_ok+0x21b/0x3e0 drivers/vhost/vhost.c:1340
vq_meta_prefetch+0xbc/0x280 drivers/vhost/vhost.c:1366
vhost_transport_do_send_pkt+0xe0/0xfd0 drivers/vhost/vsock.c:104
vhost_worker+0x23d/0x3d0 drivers/vhost/vhost.c:372
kthread+0x2e9/0x3a0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
Reported by syzbot at:
https://syzkaller.appspot.com/bug?extid=0abd373e2e50d704db87
To fix this, do two things:
1. Return -EINVAL in vhost_chr_write_iter() when userspace asks to map
a range with size 0.
2. Fix vhost_iotlb_add_range_ctx() to handle the range [0, ULONG_MAX]
by splitting it into two entries.
Fixes: 0bbe30668d89e ("vhost: factor out IOTLB")
Reported-by: syzbot+0abd373e2e50d704db87@syzkaller.appspotmail.com
Tested-by: syzbot+0abd373e2e50d704db87@syzkaller.appspotmail.com
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20220305095525.5145-1-mail@anirudhrb.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a fixup for Goodix touchscreen driver allowing it to work on certain
Cherry Trail devices
- a fix for imbalanced enable/disable regulator in Elam touchpad driver
that became apparent when used with Asus TF103C 2-in-1 dock
- a couple new input keycodes used on newer keyboards
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
HID: add mapping for KEY_ALL_APPLICATIONS
HID: add mapping for KEY_DICTATE
Input: elan_i2c - fix regulator enable count imbalance after suspend/resume
Input: elan_i2c - move regulator_[en|dis]able() out of elan_[en|dis]able_power()
Input: goodix - workaround Cherry Trail devices with a bogus ACPI Interrupt() resource
Input: goodix - use the new soc_intel_is_byt() helper
Input: samsung-keypad - properly state IOMEM dependency
|
|
This patch adds matrix keypad support for Mediatek SoCs.
Signed-off-by: fengping.yu <fengping.yu@mediatek.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220303154302.252041-3-mkorpershoek@baylibre.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
dsp_pipeline_build() allocates dup pointer by kstrdup(cfg),
but then it updates dup variable by strsep(&dup, "|").
As a result when it calls kfree(dup), the dup variable contains NULL.
Found by Linux Driver Verification project (linuxtesting.org) with SVACE.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 960366cf8dbb ("Add mISDN DSP")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This PHY doesn't support a link-up interrupt source. If aneg is enabled
we use the "aneg complete" interrupt for this purpose, but if aneg is
disabled link-up isn't signaled currently.
According to a vendor driver there's an additional "energy detect"
interrupt source that can be used to signal link-up if aneg is disabled.
We can safely ignore this interrupt source if aneg is enabled.
This patch was tested on a TX3 Mini TV box with S905W (even though
boot message says it's a S905D).
This issue has been existing longer, but due to changes in phylib and
the driver the patch applies only from the commit marked as fixed.
Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/04cac530-ea1b-850e-6cfa-144a55c4d75d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
