| Age | Commit message (Collapse) | Author |
|---|
|
The way of getting private imx_i2c_struct in i2c_imx_clk_notifier_call()
is incorrect, should use clk_change_nb element to get correct address
and avoid below kernel dump during POST_RATE_CHANGE notify by clk
framework:
Unable to handle kernel paging request at virtual address 03ef1488
pgd = (ptrval)
[03ef1488] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: events reduce_bus_freq_handler
PC is at i2c_imx_set_clk+0x10/0xb8
LR is at i2c_imx_clk_notifier_call+0x20/0x28
pc : [<806a893c>] lr : [<806a8a04>] psr: a0080013
sp : bf399dd8 ip : bf3432ac fp : bf7c1dc0
r10: 00000002 r9 : 00000000 r8 : 00000000
r7 : 03ef1480 r6 : bf399e50 r5 : ffffffff r4 : 00000000
r3 : bf025300 r2 : bf399e50 r1 : 00b71b00 r0 : bf399be8
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 4e03004a DAC: 00000051
Process kworker/2:1 (pid: 38, stack limit = 0x(ptrval))
Stack: (0xbf399dd8 to 0xbf39a000)
9dc0: 806a89e4 00000000
9de0: ffffffff bf399e50 00000002 806a8a04 806a89e4 80142900 ffffffff 00000000
9e00: bf34ef18 bf34ef04 00000000 ffffffff bf399e50 80142d84 00000000 bf399e6c
9e20: bf34ef00 80f214c4 bf025300 00000002 80f08d08 bf017480 00000000 80142df0
9e40: 00000000 80166ed8 80c27638 8045de58 bf352340 03ef1480 00b71b00 0f82e242
9e60: bf025300 00000002 03ef1480 80f60e5c 00000001 8045edf0 00000002 8045eb08
9e80: bf025300 00000002 03ef1480 8045ee10 03ef1480 8045eb08 bf01be40 00000002
9ea0: 03ef1480 8045ee10 07de2900 8045eb08 bf01b780 00000002 07de2900 8045ee10
9ec0: 80c27898 bf399ee4 bf020a80 00000002 1f78a400 8045ee10 80f60e5c 80460514
9ee0: 80f60e5c bf01b600 bf01b480 80460460 0f82e242 bf383a80 bf383a00 80f60e5c
9f00: 00000000 bf7c1dc0 80f60e70 80460564 80f60df0 80f60d24 80f60df0 8011e72c
9f20: 00000000 80f60df0 80f60e6c bf7c4f00 00000000 8011e7ac bf274000 8013bd84
9f40: bf7c1dd8 80f03d00 bf274000 bf7c1dc0 bf274014 bf7c1dd8 80f03d00 bf398000
9f60: 00000008 8013bfb4 00000000 bf25d100 bf25d0c0 00000000 bf274000 8013bf88
9f80: bf25d11c bf0cfebc 00000000 8014140c bf25d0c0 801412ec 00000000 00000000
9fa0: 00000000 00000000 00000000 801010e8 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<806a893c>] (i2c_imx_set_clk) from [<806a8a04>] (i2c_imx_clk_notifier_call+0x20/0x28)
[<806a8a04>] (i2c_imx_clk_notifier_call) from [<80142900>] (notifier_call_chain+0x44/0x84)
[<80142900>] (notifier_call_chain) from [<80142d84>] (__srcu_notifier_call_chain+0x44/0x98)
[<80142d84>] (__srcu_notifier_call_chain) from [<80142df0>] (srcu_notifier_call_chain+0x18/0x20)
[<80142df0>] (srcu_notifier_call_chain) from [<8045de58>] (__clk_notify+0x78/0xa4)
[<8045de58>] (__clk_notify) from [<8045edf0>] (__clk_recalc_rates+0x60/0xb4)
[<8045edf0>] (__clk_recalc_rates) from [<8045ee10>] (__clk_recalc_rates+0x80/0xb4)
Code: e92d40f8 e5903298 e59072a0 e1530001 (e5975008)
---[ end trace fc7f5514b97b6cbb ]---
Fixes: 90ad2cbe88c2 ("i2c: imx: use clk notifier for rate changes")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
After this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
alias: of:N*T*Cst,st95hfC*
alias: of:N*T*Cst,st95hf
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AMD family 17h Models 10h-2Fh may report a high number of L1 BTB MCA
errors under certain conditions. The errors are benign and can safely be
ignored. However, the high error rate may cause the MCA threshold
counter to overflow causing a high rate of thresholding interrupts.
In addition, users may see the errors reported through the AMD MCE
decoder module, even with the interrupt disabled, due to MCA polling.
Clear the "Counter Present" bit in the Instruction Fetch bank's
MCA_MISC0 register. This will prevent enabling MCA thresholding on this
bank which will prevent the high interrupt rate due to this error.
Define an AMD-specific function to filter these errors from the MCE
event pool so that they don't get reported during early boot.
Rename filter function in EDAC/mce_amd to avoid a naming conflict, while
at it.
[ bp: Move function prototype to the internal header and
massage/cleanup, fix typos. ]
Reported-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "clemej@gmail.com" <clemej@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Shirish S <Shirish.S@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Cc: <stable@vger.kernel.org> # 5.0.x: c95b323dcd35: x86/MCE/AMD: Turn off MC4_MISC thresholding on all family 0x15 models
Cc: <stable@vger.kernel.org> # 5.0.x: 30aa3d26edb0: x86/MCE/AMD: Carve out the MC4_MISC thresholding quirk
Cc: <stable@vger.kernel.org> # 5.0.x: 9308fd407455: x86/MCE: Group AMD function prototypes in <asm/mce.h>
Cc: <stable@vger.kernel.org> # 5.0.x
Link: https://lkml.kernel.org/r/20190325163410.171021-2-Yazen.Ghannam@amd.com
|
|
Since commit 222b5f044159 ("drm/sched: Refactor ring mirror list
handling."), drm_sched_hw_job_reset is no longer there, so let's adjust
the doc comment accordingly.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In order to make sure that the plane color space gets reset correctly.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Initialize the flow input colorspaces to unknown and reset to that value
when the channel gets disabled. This avoids the state getting mixed up
with a previous mode.
Also keep the CSC settings for the background flow intact when disabling
the foreground flow.
Root-caused-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Like arm-cci, arm-ccn has the same issue of disabling preemption around
operations which can take mutexes. Again, remove the definite bug by
simply not trying to fight the theoretical races. And since we are
touching the hotplug handling code, take the opportunity to streamline
it, as there's really no need to store a full-sized cpumask to keep
track of a single CPU ID.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Uncore PMU drivers face an awkward cyclic dependency wherein:
- They have to pick a valid online CPU to associate with before
registering the PMU device, since it will get exposed to userspace
immediately.
- The PMU registration has to be be at least partly complete before
hotplug events can be handled, since trying to migrate an
uninitialised context would be bad.
- The hotplug handler has to be ready as soon as a CPU is chosen, lest
it go offline without the user-visible cpumask value getting updated.
The arm-cci driver has tried to solve this by using get_cpu() to pick
the current CPU and prevent it from disappearing while both
registrations are performed, but that results in taking mutexes with
preemption disabled, which makes certain configurations very unhappy:
[ 1.983337] BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:2004
[ 1.983340] in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: swapper/0
[ 1.983342] Preemption disabled at:
[ 1.983353] [<ffffff80089801f4>] cci_pmu_probe+0x1dc/0x488
[ 1.983360] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.20-rt8-yocto-preempt-rt #1
[ 1.983362] Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
[ 1.983364] Call trace:
[ 1.983369] dump_backtrace+0x0/0x158
[ 1.983372] show_stack+0x24/0x30
[ 1.983378] dump_stack+0x80/0xa4
[ 1.983383] ___might_sleep+0x138/0x160
[ 1.983386] __might_sleep+0x58/0x90
[ 1.983391] __rt_mutex_lock_state+0x30/0xc0
[ 1.983395] _mutex_lock+0x24/0x30
[ 1.983400] perf_pmu_register+0x2c/0x388
[ 1.983404] cci_pmu_probe+0x2bc/0x488
[ 1.983409] platform_drv_probe+0x58/0xa8
It is not feasible to resolve all the possible races outside of the perf
core itself, so address the immediate bug by following the example of
nearly every other PMU driver and not even trying to do so. Registering
the hotplug notifier first should minimise the window in which things
can go wrong, so that's about as much as we can reasonably do here. This
also revealed an additional race in assigning the global pointer too
late relative to the hotplug notifier, which gets fixed in the process.
Reported-by: Li, Meng <Meng.Li@windriver.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
When building CONFIG_ACPI is not set
gcc warn this:
drivers/gpio/gpio-merrifield.c: In function mrfld_gpio_get_pinctrl_dev_name:
drivers/gpio/gpio-merrifield.c:388:19: error: dereferencing pointer to incomplete type struct acpi_device
put_device(&adev->dev);
^~
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d00d2109c367 ("gpio: merrifield: Convert to use acpi_dev_get_first_match_dev()")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currenly, __cpufreq_get() called by show_cpuinfo_cur_freq() will check
->get callback. That is needless since cpuinfo_cur_freq attribute will
not be created if ->get is not set. So let's drop it in __cpufreq_get().
Also keep this check in cpufreq_get().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Skip conversion to platform_device and use dev_get_drvdata() directly.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The strcpy() function is being deprecated. Replace it by the safer
strscpy() and fix the following Coverity warnings:
"You might overrun the 15-character fixed-size string event->bus_id
by copying bus_id without checking the length."
"You might overrun the 20-character fixed-size string event->device_class
by copying device_class without checking the length."
Addresses-Coverity-ID: 139001 ("Copy into fixed size buffer")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The tx_status poll in the rcar_dmac driver reads the status register
which indicates which chunk is busy (DMACHCRB). Afterwards the point
inside the chunk is read from DMATCRB. It is possible that the chunk
has changed between the two reads. The result is a non-monotonous
increase of the residue. Fix this by introducing a 'safe read' logic.
Fixes: 73a47bd0da66 ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue")
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: <stable@vger.kernel.org> # v4.16+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Having a cyclic DMA, a residue 0 is not an indication of a completed
DMA. In case of cyclic DMA make sure that dma_set_residue() is called
and with this a residue of 0 is forwarded correctly to the caller.
Fixes: 3544d2878817 ("dmaengine: rcar-dmac: use result of updated get_residue in tx_status")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Yao Lihua <ylhuajnu@outlook.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The commit af19b7ce76ba ("mmc: bcm2835: Avoid possible races on
data requests") introduces a possible circular locking dependency,
which is triggered by swapping to the sdhost interface.
So instead of reintroduce the race condition again, we could also
avoid this situation by using GFP_NOWAIT for the allocation of the
DMA buffer descriptors.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: af19b7ce76ba ("mmc: bcm2835: Avoid possible races on data requests")
Link: http://lists.infradead.org/pipermail/linux-rpi-kernel/2019-March/008615.html
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
stmmac_check_ether_addr() checks the MAC address and assigns one in
driver open(). In many cases when we create slave netdevice, the dev
addr is inherited from master but the master dev addr maybe NULL at
that time, so move this call to driver probe so that address is
always valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Tested-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Sneh Shah <snehshah@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes:
- Fix indirect syscall tracing & seccomp filtering for big endian
MIPS64 kernels, which previously loaded the syscall number
incorrectly & would always use zero.
- Fix performance counter IRQ setup for Atheros/ath79 SoCs, allowing
perf to function on those systems.
And not really a fix, but a useful addition:
- Add a Broadcom mailing list to the MAINTAINERS entry for BMIPS
systems to allow relevant engineers to track patch submissions"
* tag 'mips_fixes_5.1_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: perf: ath79: Fix perfcount IRQ assignment
MIPS: scall64-o32: Fix indirect syscall number load
MAINTAINERS: BMIPS: Add internal Broadcom mailing list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: aic7xxx: fix EISA support
Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
scsi: core: set result when the command cannot be dispatched
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pill i3c fixes from Boris Brezillon:
- fix the random PID check
- fix the disable controller logic in the designware driver
- fix I3C entry in MAINTAINERS
* tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
MAINTAINERS: Fix the I3C entry
i3c: dw: Fix dw_i3c_master_disable controller by using correct mask
i3c: Fix the verification of random PID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Misc clocksource driver fixes, and a sched-clock wrapping fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers/sched_clock: Prevent generic sched_clock wrap caused by tick_freeze()
clocksource/drivers/timer-ti-dm: Remove omap_dm_timer_set_load_start
clocksource/drivers/oxnas: Fix OX820 compatible
clocksource/drivers/arm_arch_timer: Remove unneeded pr_fmt macro
clocksource/drivers/npcm: select TIMER_OF
|
|
Modify ->cec_entered in the critical section of the mutex.
Signed-off-by: WANG Chao <chao.wang@ucloud.cn>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190418034115.75954-2-chao.wang@ucloud.cn
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-04-19
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.7:
('net/mlx5e: ethtool, Remove unsupported SFP EEPROM high pages query')
For -stable v4.19:
('net/mlx5e: Fix the max MTU check in case of XDP')
For -stable v5.0:
('net/mlx5e: Fix use-after-free after xdp_return_frame')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we add a bond device which is already the master of the team interface,
we will hold the team->lock in team_add_slave() first and then request the
lock in team_set_mac_address() again. The functions are called like:
- team_add_slave()
- team_port_add()
- team_port_enter()
- team_modeop_port_enter()
- __set_port_dev_addr()
- dev_set_mac_address()
- bond_set_mac_address()
- dev_set_mac_address()
- team_set_mac_address
Although team_upper_dev_link() would check the upper devices but it is
called too late. Fix it by adding a checking before processing the slave.
v2: Do not split the string in netdev_err()
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Querying EEPROM high pages data for SFP module is currently
not supported by our driver and yet queried, resulting in
invalid FW queries.
Set the EEPROM ethtool data length to 256 for SFP module will
limit the reading for page 0 only and prevent invalid FW queries.
Fixes: bb64143eee8c ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MLX5E_XDP_MAX_MTU was calculated incorrectly. It didn't account for
NET_IP_ALIGN and MLX5E_HW2SW_MTU, and it also misused MLX5_SKB_FRAG_SZ.
This commit fixes the calculations and adds a brief explanation for the
formula used.
Fixes: a26a5bdf3ee2d ("net/mlx5e: Restrict the combination of large MTU and XDP")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
xdp_return_frame releases the frame. It leads to releasing the page, so
it's not allowed to access xdpi.xdpf->len after that, because xdpi.xdpf
is at xdp->data_hard_start after convert_to_xdp_frame. This patch moves
the memory access to precede the return of the frame.
Fixes: 58b99ee3e3ebe ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clk fixes from Maxime Ripard:
- Some fixes for odd cases of the NKMP clocks
* tag 'clk-fixes-for-5.1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: nkmp: Explain why zero width check is needed
clk: sunxi-ng: nkmp: Avoid GENMASK(-1, 0)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are five small fixes for some tty/serial/vt issues that have been
reported.
The vt one has been around for a while, it is good to finally get that
resolved. The others fix a build warning that showed up in 5.1-rc1,
and resolve a problem in the sh-sci driver.
Note, the second patch for build warning fix for the sc16is7xx driver
was just applied to the tree, as it resolves a problem with the
previous patch to try to solve the issue. It has not shown up in
linux-next yet, unlike all of the other patches, but it has passed
0-day testing and everyone seems to agree that it is correct"
* tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: put err_spi and err_i2c into correct #ifdef
vt: fix cursor when clearing the screen
sc16is7xx: move label 'err_spi' to correct section
serial: sh-sci: Fix HSCIF RX sampling point adjustment
serial: sh-sci: Fix HSCIF RX sampling point calculation
|
|
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I've discovered following discrepancy in the bindings/net/ethernet.txt
documentation, where it states following:
- nvmem-cells: phandle, reference to an nvmem node for the MAC address;
- nvmem-cell-names: string, should be "mac-address" if nvmem is to be..
which is actually misleading and confusing. There are only two ethernet
drivers in the tree, cadence/macb and davinci which supports this
properties.
This nvmem-cell* properties were introduced in commit 9217e566bdee
("of_net: Implement of_get_nvmem_mac_address helper"), but
commit afa64a72b862 ("of: net: kill of_get_nvmem_mac_address()")
forget to properly clean up this parts.
So this patch fixes the documentation by moving the nvmem-cell*
properties at the appropriate places. While at it, I've removed unused
include as well.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fixes: afa64a72b862 ("of: net: kill of_get_nvmem_mac_address()")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here is a bunch of IIO driver fixes, and some smaller staging driver
fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
all resolve a number of reported issues and have been in linux-next
for a few weeks with no reported issues.
The other staging driver fixes are all tiny, resolving some reported
issues in the comedi and most drivers, as well as some erofs fixes.
All of these patches have been in linux-next with no reported issues"
* tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
staging: comedi: ni_usb6501: Fix use of uninitialized mutex
staging: erofs: fix unexpected out-of-bound data access
staging: comedi: vmk80xx: Fix possible double-free of ->usb_rx_buf
staging: comedi: vmk80xx: Fix use of uninitialized semaphore
staging: most: core: use device description as name
iio: core: fix a possible circular locking dependency
iio: ad_sigma_delta: select channel when reading register
iio: pms7003: select IIO_TRIGGERED_BUFFER
iio: cros_ec: Fix the maths for gyro scale calculation
iio: adc: xilinx: prevent touching unclocked h/w on remove
iio: adc: xilinx: fix potential use-after-free on probe
iio: adc: xilinx: fix potential use-after-free on remove
iio: dac: mcp4725: add missing powerdown bits in store eeprom
io: accel: kxcjk1013: restore the range after resume.
iio:chemical:bme680: Fix SPI read interface
iio:chemical:bme680: Fix, report temperature in millidegrees
iio: chemical: fix missing Kconfig block for sgp30
iio: adc: at91: disable adc channel interrupt in timeout case
iio: gyro: mpu3050: fix chip ID reading
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are four small misc driver fixes for 5.1-rc6.
Nothing major at all, they fix up a Kconfig issues, a SPDX invalid
license tag, and two tiny bugfixes.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
drivers: power: supply: goldfish_battery: Fix bogus SPDX identifier
extcon: ptn5150: fix COMPILE_TEST dependencies
misc: fastrpc: add checked value for dma_set_mask
habanalabs: remove low credit limit of DMA #0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- several new key mappings for HID
- a host of new ACPI IDs used to identify Elan touchpads in Lenovo
laptops
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: snvs_pwrkey - initialize necessary driver data before enabling IRQ
HID: input: add mapping for "Toggle Display" key
HID: input: add mapping for "Full Screen" key
HID: input: add mapping for keyboard Brightness Up/Down/Toggle keys
HID: input: add mapping for Expose/Overview key
HID: input: fix mapping of aspect ratio key
[media] doc-rst: switch to new names for Full Screen/Aspect keys
Input: document meanings of KEY_SCREEN and KEY_ZOOM
Input: elan_i2c - add hardware ID for multiple Lenovo laptops
|
|
dumping
The core dumping code has always run without holding the mmap_sem for
writing, despite that is the only way to ensure that the entire vma
layout will not change from under it. Only using some signal
serialization on the processes belonging to the mm is not nearly enough.
This was pointed out earlier. For example in Hugh's post from Jul 2017:
https://lkml.kernel.org/r/alpine.LSU.2.11.1707191716030.2055@eggly.anvils
"Not strictly relevant here, but a related note: I was very surprised
to discover, only quite recently, how handle_mm_fault() may be called
without down_read(mmap_sem) - when core dumping. That seems a
misguided optimization to me, which would also be nice to correct"
In particular because the growsdown and growsup can move the
vm_start/vm_end the various loops the core dump does around the vma will
not be consistent if page faults can happen concurrently.
Pretty much all users calling mmget_not_zero()/get_task_mm() and then
taking the mmap_sem had the potential to introduce unexpected side
effects in the core dumping code.
Adding mmap_sem for writing around the ->core_dump invocation is a
viable long term fix, but it requires removing all copy user and page
faults and to replace them with get_dump_page() for all binary formats
which is not suitable as a short term fix.
For the time being this solution manually covers the places that can
confuse the core dump either by altering the vma layout or the vma flags
while it runs. Once ->core_dump runs under mmap_sem for writing the
function mmget_still_valid() can be dropped.
Allowing mmap_sem protected sections to run in parallel with the
coredump provides some minor parallelism advantage to the swapoff code
(which seems to be safe enough by never mangling any vma field and can
keep doing swapins in parallel to the core dumping) and to some other
corner case.
In order to facilitate the backporting I added "Fixes: 86039bd3b4e6"
however the side effect of this same race condition in /proc/pid/mem
should be reproducible since before 2.6.12-rc2 so I couldn't add any
other "Fixes:" because there's no hash beyond the git genesis commit.
Because find_extend_vma() is the only location outside of the process
context that could modify the "mm" structures under mmap_sem for
reading, by adding the mmget_still_valid() check to it, all other cases
that take the mmap_sem for reading don't need the new check after
mmget_not_zero()/get_task_mm(). The expand_stack() in page fault
context also doesn't need the new check, because all tasks under core
dumping are frozen.
Link: http://lkml.kernel.org/r/20190325224949.11068-1-aarcange@redhat.com
Fixes: 86039bd3b4e6 ("userfaultfd: add new syscall to provide memory externalization")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Jann Horn <jannh@google.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When adding memory by probing a memory block in the sysfs interface,
there is an obvious issue where we will unlock the device_hotplug_lock
when we failed to takes it.
That issue was introduced in 8df1d0e4a265 ("mm/memory_hotplug: make
add_memory() take the device_hotplug_lock").
We should drop out in time when failing to take the device_hotplug_lock.
Link: http://lkml.kernel.org/r/1554696437-9593-1-git-send-email-zhongjiang@huawei.com
Fixes: 8df1d0e4a265 ("mm/memory_hotplug: make add_memory() take the device_hotplug_lock")
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reported-by: Yang yingliang <yangyingliang@huawei.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When a driver unloads without unloading TTM we don't correctly
clear the global structures leading to errors on re-init.
Next step should probably be to remove the global structures and
kobjs all together, but this is tricky since we need to maintain
backward compatibility.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
CC: stable@vger.kernel.org # 5.0.x
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB. This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.
In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS. Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop. The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.
This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner. It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed. And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).
Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
err_spi is only called within SERIAL_SC16IS7XX_SPI
while err_i2c is called inside SERIAL_SC16IS7XX_I2C.
So we need to put err_spi and err_i2c into each #ifdef
accordingly.
This change fixes ("sc16is7xx: move label 'err_spi'
to correct section").
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of relying on the now removed NULL argument to
pci_alloc_consistent, switch to the generic DMA API, and store the struct
device so that we can pass it.
Fixes: 4167b2ad5182 ("PCI: Remove NULL device handling from PCI DMA API")
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch clears FC_RP_STARTED flag during logoff, because of this
re-login(flogi) didn't happen to the switch.
This reverts commit 1550ec458e0cf1a40a170ab1f4c46e3f52860f65.
Fixes: 1550ec458e0c ("scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO")
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Hannes Reinecke <hare@#suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We recently introduced a change to support devm clk lookups. That change
introduced a code-path that used clk_find() without holding the
'clocks_mutex'. Unfortunately, clk_find() iterates over the 'clocks'
list and so we need to prevent the list from being modified at the same
time. Do this by holding the mutex and checking to make sure it's held
while iterating the list.
Note, we don't really care if the lookup is freed after we find it with
clk_find() because we're just doing a pointer comparison, but if we did
care we would need to keep holding the mutex while we dereference the
clk_lookup pointer.
Fixes: 3eee6c7d119c ("clkdev: add managed clkdev lookup registration")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
For the board name "SIMATIC IOT2000", currently there are 2 types of
hardware, IOT2020 and IOT2040. The IOT2020 is identified by its unique
asset tag. Match on it first. If we then match on the board name only,
we will catch all IOT2040 variants. In the future there will be no other
devices with the "SIMATIC IOT2000" DMI board name but different
hardware.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a debug message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If link is down and autoneg is set to on/off, the status in ethtool does
not change.
The reason is when the link is down the function returns with zero
before changing autoneg value.
Move the checking of link state (up/down) to be performed after setting
autoneg value, in order to be sure that autoneg will change in any case.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During driver initialization the driver sends a reset to the device and
waits for the firmware to signal that it is ready to continue.
Commit d2f372ba0914 ("mlxsw: pci: Increase PCI SW reset timeout")
increased the timeout to 13 seconds due to longer PHY calibration in
Spectrum-2 compared to Spectrum-1.
Recently it became apparent that this timeout is too short and therefore
this patch increases it again to a safer limit that will be reduced in
the future.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Fixes: d2f372ba0914 ("mlxsw: pci: Increase PCI SW reset timeout")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both Spectrum-1 and Spectrum-2 chips are currently configured such that
pairs of TC n (which is used for UC traffic) and TC n+8 (which is used
for MC traffic) are feeding into the same subgroup. Strict
prioritization is configured between the two TCs, and by enabling
MC-aware mode on the switch, the lower-numbered (UC) TCs are favored
over the higher-numbered (MC) TCs.
On Spectrum-2 however, there is an issue in configuration of the
MC-aware mode. As a result, MC traffic is prioritized over UC traffic.
To work around the issue, configure the MC TCs with DWRR mode (while
keeping the UC TCs in strict mode).
With this patch, the multicast-unicast arbitration results in the same
behavior on both Spectrum-1 and Spectrum-2 chips.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 bug fixes from Martin Schwidefsky:
- Fix overwrite of the initial ramdisk due to misuse of IS_ENABLED
- Fix integer overflow in the dasd driver resulting in incorrect number
of blocks for large devices
- Fix a lockdep false positive in the 3270 driver
- Fix a deadlock in the zcrypt driver
- Fix incorrect debug feature entries in the pkey api
- Fix inline assembly constraints fallout with CONFIG_KASAN=y
* tag 's390-5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: correct some inline assembly constraints
s390/pkey: add one more argument space for debug feature entry
s390/zcrypt: fix possible deadlock situation on ap queue remove
s390/3270: fix lockdep false positive on view->lock
s390/dasd: Fix capacity calculation for large volumes
s390/mem_detect: Use IS_ENABLED(CONFIG_BLK_DEV_INITRD)
|
|
Pull drm fixes from Dave Airlie:
"Since Easter is looming for me, I'm just pushing whatever is in my
tree, I'll see what else turns up and maybe I'll send another pull
early next week if there is anything.
tegra:
- stream id programming fix
- avoid divide by 0 for bad hdmi audio setup code
ttm:
- Hugepages fix
- refcount imbalance in error path fix
amdgpu:
- GPU VM fixes for Vega/RV
- DC AUX fix for active DP-DVI dongles
- DC fix for multihead regression"
* tag 'drm-fixes-2019-04-18' of git://anongit.freedesktop.org/drm/drm:
drm/tegra: hdmi: Setup audio only if configured
drm/amd/display: If one stream full updates, full update all planes
drm/amdgpu/gmc9: fix VM_L2_CNTL3 programming
drm/amdgpu: shadow in shadow_list without tbo.mem.start cause page fault in sriov TDR
gpu: host1x: Program stream ID to bypass without SMMU
drm/amd/display: extending AUX SW Timeout
drm/ttm: fix dma_fence refcount imbalance on error path
drm/ttm: fix incrementing the page pointer for huge pages
drm/ttm: fix start page for huge page check in ttm_put_pages()
drm/ttm: fix out-of-bounds read in ttm_put_pages() v2
|
