| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This register is same as in MAX17047 and MAX17050, so there's no need
for custom casing it.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add the rockchip serial flash controller (SFC) driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20210812134546.31340-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit a02e8964eaf92 ("virtio-net: ethtool configurable LRO")
maps LRO to virtio guest offloading features and allows the
administrator to enable and disable those features via ethtool.
This leads to several issues:
- For a device that doesn't support control guest offloads, the "LRO"
can't be disabled triggering WARN in dev_disable_lro() when turning
off LRO or when enabling forwarding bridging etc.
- For a device that supports control guest offloads, the guest
offloads are disabled in cases of bridging, forwarding etc slowing
down the traffic.
Fix this by using NETIF_F_GRO_HW instead. Though the spec does not
guarantee packets to be re-segmented as the original ones,
we can add that to the spec, possibly with a flag for devices to
differentiate between GRO and LRO.
Further, we never advertised LRO historically before a02e8964eaf92
("virtio-net: ethtool configurable LRO") and so bridged/forwarded
configs effectively always relied on virtio receive offloads behaving
like GRO - thus even if this breaks any configs it is at least not
a regression.
Fixes: a02e8964eaf92 ("virtio-net: ethtool configurable LRO")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Ivan <ivan@prestigetransportation.com>
Tested-by: Ivan <ivan@prestigetransportation.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To fix the "reverse-NAT" for replies.
When a packet is sent over a VRF, the POST_ROUTING hooks are called
twice: Once from the VRF interface, and once from the "actual"
interface the packet will be sent from:
1) First SNAT: l3mdev_l3_out() -> vrf_l3_out() -> .. -> vrf_output_direct()
This causes the POST_ROUTING hooks to run.
2) Second SNAT: 'ip_output()' calls POST_ROUTING hooks again.
Similarly for replies, first ip_rcv() calls PRE_ROUTING hooks, and
second vrf_l3_rcv() calls them again.
As an example, consider the following SNAT rule:
> iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j SNAT --to-source 2.2.2.2 -o vrf_1
In this case sending over a VRF will create 2 conntrack entries.
The first is from the VRF interface, which performs the IP SNAT.
The second will run the SNAT, but since the "expected reply" will remain
the same, conntrack randomizes the source port of the packet:
e..g With a socket bound to 1.1.1.1:10000, sending to 3.3.3.3:53, the conntrack
rules are:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=0 bytes=0 mark=0 use=1
udp 17 29 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
i.e. First SNAT IP from 1.1.1.1 --> 2.2.2.2, and second the src port is
SNAT-ed from 10000 --> 61033.
But when a reply is sent (3.3.3.3:53 -> 2.2.2.2:61033) only the later
conntrack entry is matched:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=1 bytes=49 mark=0 use=1
udp 17 28 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
And a "port 61033 unreachable" ICMP packet is sent back.
The issue is that when PRE_ROUTING hooks are called from vrf_l3_rcv(),
the skb already has a conntrack flow attached to it, which means
nf_conntrack_in() will not resolve the flow again.
This means only the dest port is "reverse-NATed" (61033 -> 10000) but
the dest IP remains 2.2.2.2, and since the socket is bound to 1.1.1.1 it's
not received.
This can be verified by logging the 4-tuple of the packet in '__udp4_lib_rcv()'.
The fix is then to reset the flow when skb is received on a VRF, to let
conntrack resolve the flow again (which now will hit the earlier flow).
To reproduce: (Without the fix "Got pkt_to_nat_port" will not be printed by
running 'bash ./repro'):
$ cat run_in_A1.py
import logging
logging.getLogger("scapy.runtime").setLevel(logging.ERROR)
from scapy.all import *
import argparse
def get_packet_to_send(udp_dst_port, msg_name):
return Ether(src='11:22:33:44:55:66', dst=iface_mac)/ \
IP(src='3.3.3.3', dst='2.2.2.2')/ \
UDP(sport=53, dport=udp_dst_port)/ \
Raw(f'{msg_name}\x0012345678901234567890')
parser = argparse.ArgumentParser()
parser.add_argument('-iface_mac', dest="iface_mac", type=str, required=True,
help="From run_in_A3.py")
parser.add_argument('-socket_port', dest="socket_port", type=str,
required=True, help="From run_in_A3.py")
parser.add_argument('-v1_mac', dest="v1_mac", type=str, required=True,
help="From script")
args, _ = parser.parse_known_args()
iface_mac = args.iface_mac
socket_port = int(args.socket_port)
v1_mac = args.v1_mac
print(f'Source port before NAT: {socket_port}')
while True:
pkts = sniff(iface='_v0', store=True, count=1, timeout=10)
if 0 == len(pkts):
print('Something failed, rerun the script :(', flush=True)
break
pkt = pkts[0]
if not pkt.haslayer('UDP'):
continue
pkt_sport = pkt.getlayer('UDP').sport
print(f'Source port after NAT: {pkt_sport}', flush=True)
pkt_to_send = get_packet_to_send(pkt_sport, 'pkt_to_nat_port')
sendp(pkt_to_send, '_v0', verbose=False) # Will not be received
pkt_to_send = get_packet_to_send(socket_port, 'pkt_to_socket_port')
sendp(pkt_to_send, '_v0', verbose=False)
break
$ cat run_in_A2.py
import socket
import netifaces
print(f"{netifaces.ifaddresses('e00000')[netifaces.AF_LINK][0]['addr']}",
flush=True)
s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
s.setsockopt(socket.SOL_SOCKET, socket.SO_BINDTODEVICE,
str('vrf_1' + '\0').encode('utf-8'))
s.connect(('3.3.3.3', 53))
print(f'{s. getsockname()[1]}', flush=True)
s.settimeout(5)
while True:
try:
# Periodically send in order to keep the conntrack entry alive.
s.send(b'a'*40)
resp = s.recvfrom(1024)
msg_name = resp[0].decode('utf-8').split('\0')[0]
print(f"Got {msg_name}", flush=True)
except Exception as e:
pass
$ cat repro.sh
ip netns del A1 2> /dev/null
ip netns del A2 2> /dev/null
ip netns add A1
ip netns add A2
ip -n A1 link add _v0 type veth peer name _v1 netns A2
ip -n A1 link set _v0 up
ip -n A2 link add e00000 type bond
ip -n A2 link add lo0 type dummy
ip -n A2 link add vrf_1 type vrf table 10001
ip -n A2 link set vrf_1 up
ip -n A2 link set e00000 master vrf_1
ip -n A2 addr add 1.1.1.1/24 dev e00000
ip -n A2 link set e00000 up
ip -n A2 link set _v1 master e00000
ip -n A2 link set _v1 up
ip -n A2 link set lo0 up
ip -n A2 addr add 2.2.2.2/32 dev lo0
ip -n A2 neigh add 1.1.1.10 lladdr 77:77:77:77:77:77 dev e00000
ip -n A2 route add 3.3.3.3/32 via 1.1.1.10 dev e00000 table 10001
ip netns exec A2 iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j \
SNAT --to-source 2.2.2.2 -o vrf_1
sleep 5
ip netns exec A2 python3 run_in_A2.py > x &
XPID=$!
sleep 5
IFACE_MAC=`sed -n 1p x`
SOCKET_PORT=`sed -n 2p x`
V1_MAC=`ip -n A2 link show _v1 | sed -n 2p | awk '{print $2'}`
ip netns exec A1 python3 run_in_A1.py -iface_mac ${IFACE_MAC} -socket_port \
${SOCKET_PORT} -v1_mac ${SOCKET_PORT}
sleep 5
kill -9 $XPID
wait $XPID 2> /dev/null
ip netns del A1
ip netns del A2
tail x -n 2
rm x
set +x
Fixes: 73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: Lahav Schlesinger <lschlesinger@drivenets.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210815120002.2787653-1-lschlesinger@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With the patch to separate the gpio driver from the pinctrl driver, now
the pinctrl-rockchip can drop the gpio related codes now.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012146.1119289-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There has spin lock for irq set type already, so drop irq_gc_lock and
irq_gc_unlock.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012135.1119234-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The next version gpio controller on SoCs like rk3568 have more write
mask bits for registers.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012123.1119179-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Store register offsets in the struct rockchip_gpio_regs, this patch
prepare for the driver update for new gpio controller.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012111.1119125-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch add support for rockchip gpio controller, which is supported
in pinctrl driver in the past.
With this patch, the pinctrl-rockchip driver will drop gpio related
codes and populate platform driver to gpio-rockchip.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012053.1119069-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Store a pointer from the pinctrl device for the gpio bank.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816011948.1118959-4-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Separate struct rockchip_pin_bank to pinctrl-rockchip.h file, which will
be used by gpio-rockchip driver in the future.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816011948.1118959-3-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since gate and ungate pclk of gpio has very litte benifit for system
power consumption, just keep it always ungate.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816011948.1118959-2-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/fixes
NXP/FSL SoC driver fixes for v5.14
QE interrupt controller driver
- Convert it to platform_device driver to make it work with fw_devlink
- Fix static analysis issue
* tag 'soc-fsl-fix-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qe: fix static checker warning
soc: fsl: qe: convert QE interrupt controller to platform_device
Link: https://lore.kernel.org/r/20210813222305.13663-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.
[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.
v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
KFDSVMRangeTest.SetGetAttributesTest randomly fails in stress test.
Note: Google Test filter = KFDSVMRangeTest.*
[==========] Running 18 tests from 1 test case.
[----------] Global test environment set-up.
[----------] 18 tests from KFDSVMRangeTest
[ RUN ] KFDSVMRangeTest.BasicSystemMemTest
[ OK ] KFDSVMRangeTest.BasicSystemMemTest (30 ms)
[ RUN ] KFDSVMRangeTest.SetGetAttributesTest
[ ] Get default atrributes
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:154: Failure
Value of: expectedDefaultResults[i]
Actual: 4294967295
Expected: outputAttributes[i].value
Which is: 0
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:154: Failure
Value of: expectedDefaultResults[i]
Actual: 4294967295
Expected: outputAttributes[i].value
Which is: 0
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:152: Failure
Value of: expectedDefaultResults[i]
Actual: 4
Expected: outputAttributes[i].type
Which is: 2
[ ] Setting/Getting atrributes
[ FAILED ]
the root cause is that svm work queue has not finished when svm_range_get_attr is called, thus
some garbage svm interval tree data make svm_range_get_attr get wrong result. Flush work queue before
iterate svm interval tree.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
change the workload type for some cards as it is needed.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 0979d43259e13846d86ba17e451e17fec185d240.
Revert this because it does not apply to all the cards.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The Altera EDAC driver has several features conditionally built
depending on Kconfig options. The edac_device_prv_data structures
are conditionally used in of_device_id tables. They reference other
functions and structures which can be defined as __maybe_unused.
Silence build warnings like:
drivers/edac/altera_edac.c:643:37: warning:
‘altr_edac_device_inject_fops’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lkml.kernel.org/r/20210601092704.203555-1-krzysztof.kozlowski@canonical.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"MTD core fixes:
- Fix lock hierarchy in deregister_mtd_blktrans
- Handle flashes without OTP gracefully
- Break circular locks in register_mtd_blktrans
MTD device fixes:
- mchp48l640:
- Fix memory leak on cmd
- Silence some uninitialized variable warnings
- blkdevs:
- Initialize rq.limits.discard_granularity
CFI fixes:
- Fix crash when erasing/writing AMD cards
Raw NAND fixes:
- Fix of_get_nand_secure_regions():
- Add a missing check
- Avoid an unwanted probe failure when a DT property is missing"
* tag 'mtd/fixes-for-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: Fix probe failure due to of_get_nand_secure_regions()
mtd: fix lock hierarchy in deregister_mtd_blktrans
mtd: devices: mchp48l640: Fix memory leak on cmd
mtd: cfi_cmdset_0002: fix crash when erasing/writing AMD cards
mtd: core: handle flashes without OTP gracefully
mtd: mchp48l640: silence some uninitialized variable warnings
mtd: break circular locks in register_mtd_blktrans
mtd: rawnand: Add a check in of_get_nand_secure_regions()
mtd: mtd_blkdevs: Initialize rq.limits.discard_granularity
|
|
It was reported by a user with a Dell m15 R5 (5800H) that
the keyboard backlight was turning on when entering suspend
and turning off when exiting (the opposite of how it should be).
The user bisected it back to commit 5dbf50997578 ("ACPI: PM:
s2idle: Add support for new Microsoft UUID"). Previous to that
commit the LEDs didn't turn off at all. Confirming in the spec,
these were reversed when introduced.
Fix them to match the spec.
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1230#note_1021836
Fixes: 5dbf50997578 ("ACPI: PM: s2idle: Add support for new Microsoft UUID")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes in virtio, vhost, and vdpa drivers"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Fix queue type selection logic
vdpa/mlx5: Avoid destroying MR on empty iotlb
tools/virtio: fix build
virtio_ring: pull in spinlock header
vringh: pull in spinlock header
virtio-blk: Add validation for block size in config space
vringh: Use wiov->used to check for read/write desc order
virtio_vdpa: reject invalid vq indices
vdpa: Add documentation for vdpa_alloc_device() macro
vDPA/ifcvf: Fix return value check for vdpa_alloc_device()
vp_vdpa: Fix return value check for vdpa_alloc_device()
vdpa_sim: Fix return value check for vdpa_alloc_device()
vhost: Fix the calculation in vhost_overflow()
vhost-vdpa: Fix integer overflow in vhost_vdpa_process_iotlb_update()
virtio_pci: Support surprise removal of virtio pci device
virtio: Protect vqs list access
virtio: Keep vring_del_virtqueue() mirror of VQ create
virtio: Improve vq->broken access to avoid any compiler optimization
|
|
SMB347 can supply power to USB VBUS, implement the USB VBUS regulator.
USB VBUS needs to be powered for switching OTG-cable USB port into host
mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Pin control needs to be activated by setting the enable bit, otherwise
hardware rejects all pin changes. Previously this stayed unnoticed on
Nexus 7 because pin control was enabled by default after rebooting from
downstream kernel, which uses driver that enables the bit and charger
registers are non-volatile until power supply (battery) is disconnected.
Configure the pin control enable bit. This fixes the potentially
never-enabled charging on devices that use pin control.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Utilize generic regmap caching in order to avoid unnecessary slow I2C
accesses to all constant registers each time the supply status updated
and remove local caching of charger state to make code cleaner.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The smb347_set_writable() is used by interrupt handler and outside of it.
The interrupt should be disabled when the function is used outside of
interrupt handler in order to prevent racing with the interrupt context.
Add new parameter to smb347_set_writable() that allows to disable IRQ.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
On the system PRMT table is not present, dmesg output:
$ dmesg | grep PRM
[ 1.532237] ACPI: PRMT not present
[ 1.532237] PRM: found 4294967277 modules
The result of acpi_table_parse_entries need to be checked and return
immediately if PRMT table is not present or no PRM module found.
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull operating performance points (OPP) framework fixes for v5.14
from iresh Kumar:
"This removes few WARN() statements from the OPP core."
* 'opp/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Drop empty-table checks from _put functions
opp: remove WARN when no valid OPPs remain
|
|
This fixes an accidental partial revert of commit 94dfec48fca7
("drm/imx: Add 8 pixel alignment fix") during a rebase of
commit fc1e985b67f9 ("drm/imx: ipuv3-plane: add color encoding and range
properties").
Fixes: fc1e985b67f9 ("drm/imx: ipuv3-plane: add color encoding and range properties")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210816131728.30987-1-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Video captured in 1400x1050 resolution (bytesperline aka stride = 1408
bytes) is invalid. Fix it.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Link: https://lore.kernel.org/r/m3y2bmq7a4.fsf@t19.piap.pl
[p.zabel@pengutronix.de: added "gpu: ipu-v3:" prefix to commit description]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The only way to reset the BeagleV Starlight v0.9 board[1] properly is to
tell the PMIC to reset itself which will then assert the external reset
lines of the SoC, USB hub and ethernet phy.
This adds a driver to register a reset handler to do just that.
[1] https://github.com/beagleboard/beaglev-starlight
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The bounds check on "index" doesn't catch negative values. Using
ARRAY_SIZE() directly is more readable and more robust because it prevents
negative values for "index". Fortunately we only pass valid values to
ipc_chnl_cfg_get() so this patch does not affect runtime.
Reported-by: Solomon Ucko <solly.ucko@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When clearing the chip-select mask, the controller will switch to chip
selecting the native CS0 line. Because the control register chip-select
mask is not updated in a single write this will cause undesirable
chip-selection of CS0 even when requesting to select other native
chip-select lines. This is additionally problematic as the chip-select
may still be asserted. With the ARMADA 38x SoC the controller will
assert both the desired native chip-select and CS0.
To avoid any undesirable behaviour with the chip-select lines, update
the control register with a single write. This avoids selecting CS0 and
causes the (de-)assert to apply at the same time.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20210816050228.3223661-1-nathan@nathanrossi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In 69de4421bb4c ("drm/ttm: Initialize debugfs from
ttm_global_init()"), ttm_global_init was changed so that if creation
of the debugfs global root directory fails, ttm_global_init will bail
out early and return an error, leading to initialization failure of
DRM drivers. However, not every system will be using debugfs. On such
a system, debugfs directory creation can be expected to fail, but DRM
drivers must still be usable. This changes it so that if creation of
TTM's debugfs root directory fails, then no biggie: keep calm and
carry on.
Fixes: 69de4421bb4c ("drm/ttm: Initialize debugfs from ttm_global_init()")
Signed-off-by: Dan Moulding <dmoulding@me.com>
Tested-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210810195906.22220-2-dmoulding@me.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
All bits of STATUS register are already defined (see STATUS_SMN_BIT and
further) so there is no need to define status SoC threshold min/max
values one more time.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc4f ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022c7 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple
filters are inserted and deleted by the 212 firmware.
Fixes: ae10ae740ad2 ("bnxt_en: Add new hardware RFS mode.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a possible null-pointer dereference in qed_rdma_create_qp().
Changes from V2:
- Revert checkpatch fixes.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoiding qed ll2 race condition and NULL pointer dereference as part
of the remove and recovery flows.
Changes form V1:
- Change (!p_rx->set_prod_addr).
- qed_ll2.c checkpatch fixes.
Change from V2:
- Revert "qed_ll2.c checkpatch fixes".
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The controller doesn't seem to pick-up on clock changes, so set the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN flag to query the clock frequency
directly from the clock.
Fixes: f84e411c85be ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1628334401-6577-6-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb044 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a known bug on BCM2711's SDHCI core integration where the
controller will hang when the difference between the core clock and the
bus clock is too great. Specifically this can be reproduced under the
following conditions:
- No SD card plugged in, polling thread is running, probing cards at
100 kHz.
- BCM2711's core clock configured at 500MHz or more.
So set 200 kHz as the minimum clock frequency available for that board.
For more information on the issue see this:
https://lore.kernel.org/linux-mmc/20210322185816.27582-1-nsaenz@kernel.org/T/#m11f2783a09b581da6b8a15f302625b43a6ecdeca
Fixes: f84e411c85be ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1628334401-6577-5-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.6.0-rc3-syzkaller #0
...
Workqueue: events_unbound flush_to_ldisc
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x32 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:641
__asan_report_store1_noabort+0x17/0x20 mm/kasan/generic_report.c:137
decode_data.part.0+0x23b/0x270 drivers/net/hamradio/6pack.c:843
decode_data drivers/net/hamradio/6pack.c:965 [inline]
sixpack_decode drivers/net/hamradio/6pack.c:968 [inline]
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current_opp is released only when whole OPP table is released,
otherwise it's only marked as removed by dev_pm_opp_remove_table().
Functions like dev_pm_opp_put_clkname() and dev_pm_opp_put_supported_hw()
are checking whether OPP table is empty and it's not if current_opp is
set since it holds the refcount of OPP, this produces a noisy warning
from these functions about busy OPP table. Remove the checks to fix it.
Cc: stable@vger.kernel.org
Fixes: 81c4d8a3c414 ("opp: Keep track of currently programmed OPP")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for PCI/MSI and x86 interrupt startup:
- Mask all MSI-X entries when enabling MSI-X otherwise stale unmasked
entries stay around e.g. when a crashkernel is booted.
- Enforce masking of a MSI-X table entry when updating it, which
mandatory according to speification
- Ensure that writes to MSI[-X} tables are flushed.
- Prevent invalid bits being set in the MSI mask register
- Properly serialize modifications to the mask cache and the mask
register for multi-MSI.
- Cure the violation of the affinity setting rules on X86 during
interrupt startup which can cause lost and stale interrupts. Move
the initial affinity setting ahead of actualy enabling the
interrupt.
- Ensure that MSI interrupts are completely torn down before freeing
them in the error handling case.
- Prevent an array out of bounds access in the irq timings code"
* tag 'irq-urgent-2021-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
driver core: Add missing kernel doc for device::msi_lock
genirq/msi: Ensure deactivation on teardown
genirq/timings: Prevent potential array overflow in __irq_timings_store()
x86/msi: Force affinity setup before startup
x86/ioapic: Force affinity setup before startup
genirq: Provide IRQCHIP_AFFINITY_PRE_STARTUP
PCI/MSI: Protect msi_desc::masked for multi-MSI
PCI/MSI: Use msi_mask_irq() in pci_msi_shutdown()
PCI/MSI: Correct misleading comments
PCI/MSI: Do not set invalid bits in MSI mask
PCI/MSI: Enforce MSI[X] entry updates to be visible
PCI/MSI: Enforce that MSI-X table entry is masked for update
PCI/MSI: Mask all unused MSI-X entries
PCI/MSI: Enable and mask MSI-X early
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Borislav Petkov:
"A batch of fixes for the arm64 stub image loader:
- fix a logic bug that can make the random page allocator fail
spuriously
- force reallocation of the Image when it overlaps with firmware
reserved memory regions
- fix an oversight that defeated on optimization introduced earlier
where images loaded at a suitable offset are never moved if booting
without randomization
- complain about images that were not loaded at the right offset by
the firmware image loader"
* tag 'efi_urgent_for_v5.14_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub: arm64: Double check image alignment at entry
efi/libstub: arm64: Warn when efi_random_alloc() fails
efi/libstub: arm64: Relax 2M alignment again for relocatable kernels
efi/libstub: arm64: Force Image reallocation if BSS was not reserved
arm64: efi: kaslr: Fix occasional random alloc (and boot) failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
Georgi writes:
interconnect fix for v5.14
This contains a revert for a patch that has been causing issues:
- Revert: qcom: rpmh: Add BCMs to commit list in pre_aggregate
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
Revert "interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes, all in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpt3sas: Fix incorrectly assigned error return and check
scsi: storvsc: Log TEST_UNIT_READY errors as warnings
scsi: lpfc: Move initialization of phba->poll_list earlier to avoid crash
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A couple of fixes for long standing bugs, a warning fixup, and some
miscellaneous dax cleanups.
The bugs were recently found due to new platforms looking to use the
ACPI NFIT "virtual" device definition, and new error injection
capabilities to trigger error responses to label area requests. Ira's
cleanups have been long pending, I neglected to send them earlier, and
see no harm in including them now. This has all appeared in -next with
no reported issues.
Summary:
- Fix support for NFIT "virtual" ranges (BIOS-defined memory disks)
- Fix recovery from failed label storage areas on NVDIMM devices
- Miscellaneous cleanups from Ira's investigation of
dax_direct_access paths preparing for stray-write protection"
* tag 'libnvdimm-fixes-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
tools/testing/nvdimm: Fix missing 'fallthrough' warning
libnvdimm/region: Fix label activation vs errors
ACPI: NFIT: Fix support for virtual SPA ranges
dax: Ensure errno is returned from dax_direct_access
fs/dax: Clarify nr_pages to dax_direct_access()
fs/fuse: Remove unneeded kaddr parameter
|
