| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Not much going on in the core for SPI this time but a reasonable
amount of change in the drivers:
- Removal of dmal_request_slave_channel() from Peter Ujfalusi.
- More conversions of drivers to GPIO descriptors from Linus Walleij.
- A big rework of the sh-msiof driver from Geert Uytterhoeven moving
it over to the generic native chipselect support.
- DMA support for the uniphier driver from Kunihiko Hayashi.
- New driver support for HiSilcon v3xx SPI NOR controllers from John
Garry"
* tag 'spi-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (52 commits)
dt-binding: spi: add NPCM PSPI reset binding
spi: pxa2xx: Avoid touching SSCR0_SSE on MMP2
spi: spi-fsl-qspi: Ensure width is respected in spi-mem operations
spi: npcm-pspi: modify reset support
spi: npcm-pspi: improve spi transfer performance
spi: spi-ti-qspi: fix warning
spi: npcm-pspi: fix 16 bit send and receive support
spi: pxa2xx: Add support for Intel Comet Lake PCH-V
spi: fsl: simplify error path in of_fsl_spi_probe()
spi: fsl-lpspi: fix only one cs-gpio working
spi: spi-ti-qspi: optimize byte-transfers
spi: spi-ti-qspi: support large flash devices
spi: spi-qcom-qspi: Use device managed memory for clk_bulk_data
MAINTAINERS: Add a maintainer for the HiSilicon v3xx SFC driver
spi: Add HiSilicon v3xx SPI NOR flash controller driver
dt-bindings: spi_atmel: add microchip,sam9x60-spi
spi: bcm2835: Raise maximum number of slaves to 4
spi: sh-msiof: Do not redefine STR while compile testing
spi: rspi: Add support for GPIO chip selects
spi: rspi: Add support for multiple native chip selects
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This is quite a busy release for a subsystem that's usually very
quiet, though still a small set of updates in the grand scheme of
things:
- A fix for writes to non-incrementing registers.
- An iopoll() style helper for use with atomic safe regmaps, making
it easier to transition from raw memory mapped I/O.
- Some constification"
* tag 'regmap-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix writes to non incrementing registers
regmap: add iopoll-like atomic polling macro
regmap-i2c: constify regmap_bus structures
|
|
Pull dmaengine updates from Vinod Koul:
"This time we have a bunch of core changes to support dynamic channels,
hotplug of controllers, new apis for metadata ops etc along with new
drivers for Intel data accelerators, TI K3 UDMA, PLX DMA engine and
hisilicon Kunpeng DMA engine. Also usual assorted updates to drivers.
Core:
- Support for dynamic channels
- Removal of various slave wrappers
- Make few slave request APIs as private to dmaengine
- Symlinks between channels and slaves
- Support for hotplug of controllers
- Support for metadata_ops for dma_async_tx_descriptor
- Reporting DMA cached data amount
- Virtual dma channel locking updates
New drivers/device/feature support support:
- Driver for Intel data accelerators
- Driver for TI K3 UDMA
- Driver for PLX DMA engine
- Driver for hisilicon Kunpeng DMA engine
- Support for eDMA support for QorIQ LS1028A in fsl edma driver
- Support for cyclic dma in sun4i driver
- Support for X1830 in JZ4780 driver"
* tag 'dmaengine-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (62 commits)
dmaengine: Create symlinks between DMA channels and slaves
dmaengine: hisilicon: Add Kunpeng DMA engine support
dmaengine: idxd: add char driver to expose submission portal to userland
dmaengine: idxd: connect idxd to dmaengine subsystem
dmaengine: idxd: add descriptor manipulation routines
dmaengine: idxd: add sysfs ABI for idxd driver
dmaengine: idxd: add configuration component of driver
dmaengine: idxd: Init and probe for Intel data accelerators
dmaengine: add support to dynamic register/unregister of channels
dmaengine: break out channel registration
x86/asm: add iosubmit_cmds512() based on MOVDIR64B CPU instruction
dmaengine: ti: k3-udma: fix spelling mistake "limted" -> "limited"
dmaengine: s3c24xx-dma: fix spelling mistake "to" -> "too"
dmaengine: Move dma_get_{,any_}slave_channel() to private dmaengine.h
dmaengine: Remove dma_request_slave_channel_compat() wrapper
dmaengine: Remove dma_device_satisfies_mask() wrapper
dt-bindings: fsl-imx-sdma: Add i.MX8MM/i.MX8MN/i.MX8MP compatible string
dmaengine: zynqmp_dma: fix burst length configuration
dmaengine: sun4i: Add support for cyclic requests with dedicated DMA
dmaengine: fsl-qdma: fix duplicated argument to &&
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
"This time it's surprisingly quiet (probably due to the christmas
break):
- Logitech HID++ protocol improvements from Mazin Rezk, Pedro
Vanzella and Adrian Freund
- support for hidraw uniq ioctl from Marcel Holtmann"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-hidpp: avoid duplicate error handling code in 'hidpp_probe()'
hid-logitech-hidpp: read battery voltage from newer devices
HID: logitech: Add MX Master 3 Mouse
HID: logitech-hidpp: Support WirelessDeviceStatus connect events
HID: logitech-hidpp: Support translations from short to long reports
HID: hidraw: add support uniq ioctl
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- Enable thermal policy for ASUS TUF FX705DY/FX505DY
- Support left round button on ASUS N56VB
- Support new Mellanox platforms of basic class VMOD0009 and VMOD0010
- Intel Comet Lake, Tiger Lake and Elkhart Lake support in the PMC
driver
- Big clean-up to Intel PMC core, PMC IPC and SCU IPC drivers
- Touchscreen support for the PiPO W11 tablet
* tag 'platform-drivers-x86-v5.6-1' of git://git.infradead.org/linux-platform-drivers-x86: (64 commits)
platform/x86: intel_pmc_ipc: Switch to use driver->dev_groups
platform/x86: intel_pmc_ipc: Propagate error from kstrtoul()
platform/x86: intel_pmc_ipc: Use octal permissions in sysfs attributes
platform/x86: intel_pmc_ipc: Get rid of unnecessary includes
platform/x86: intel_pmc_ipc: Drop ipc_data_readb()
platform/x86: intel_pmc_ipc: Drop intel_pmc_gcr_read() and intel_pmc_gcr_write()
platform/x86: intel_pmc_ipc: Make intel_pmc_ipc_raw_cmd() static
platform/x86: intel_pmc_ipc: Make intel_pmc_ipc_simple_command() static
platform/x86: intel_pmc_ipc: Make intel_pmc_gcr_update() static
platform/x86: intel_scu_ipc: Reformat kernel-doc comments of exported functions
platform/x86: intel_scu_ipc: Drop intel_scu_ipc_raw_command()
platform/x86: intel_scu_ipc: Drop intel_scu_ipc_io[read|write][8|16]()
platform/x86: intel_scu_ipc: Drop unused macros
platform/x86: intel_scu_ipc: Drop unused prototype intel_scu_ipc_fw_update()
platform/x86: intel_scu_ipc: Sleeping is fine when polling
platform/x86: intel_scu_ipc: Drop intel_scu_ipc_i2c_cntrl()
platform/x86: intel_scu_ipc: Remove Lincroft support
platform/x86: intel_scu_ipc: Add constants for register offsets
platform/x86: intel_scu_ipc: Fix interrupt support
platform/x86: intel_scu_ipcutil: Remove default y from Kconfig
...
|
|
Pull MMC updates from Ulf Hansson:
"There are no updates for the MEMSTICK subsystem this time. But note
that I am also carrying a patch from the pinctrl tree, which has been
shared through an immutable branch.
Summary:
MMC core:
- Convert to reasonable timeouts for all CMD6 commands (updates for
BKOPS, CACHE_FLUSH and INAND_CMD38_ARG_EXT_CSD) for eMMC
- Respect f_max clock rate at card initialization
- Add gpiod_toggle_active_low() API
- Consolidate slot-gpio code by using gpiod_toggle_active_low()
MMC host:
- Add pinctrl_select_default_state() API
- Consolidate pintctrl code by using pinctrl_select_default_state()
- mmci: Support any block sizes for SDIO for some variants
- mmci: Enable reset control for stm32_sdmmc
- mmc_spi: Toggle SPI_CS_HIGH polarity rather than hard-coding it
- renesas_sdhi: Add support for the r8a77961 variant
- renesas_sdhi: A few minor improvements
- rockchip-dw-mshc: Add support for the rk3308 variant
- sdhci: Enable support for external DMA controllers
- sdhci: Fixup error path when sending CMD12
- sdhci-brcmstb: Add support for 7216b0 variant
- sdhci-brcmstb: Add support for command queuing (CQHCI)
- sdhci-brcmstb: Add support for eMMC HS400ES mode
- sdhci-msm: Add support for the sc7180 variant
- sdhci-msm: Add support for command queuing (CQHCI)
- sdhci-of-at91: Add support for the SAM9x60 variant
- sdhci-of-at91: Improve support for tunings
- sdhci-of-esdhc: A few fixups for some clock related issues
- sdhci-omap: Add support for the am335x and the am437x variants
- sdhci-omap: Improve support for erase operations
- sdhci-omap: Add support for external DMA"
* tag 'mmc-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (89 commits)
mmc: core: Default to generic_cmd6_time as timeout in __mmc_switch()
mmc: block: Use generic_cmd6_time when modifying INAND_CMD38_ARG_EXT_CSD
mmc: core: Specify timeouts for BKOPS and CACHE_FLUSH for eMMC
mmc: sdhci-cadence: remove unneeded 'inline' marker
dt-bindings: mmc: rockchip-dw-mshc: add description for rk3308
dt-bindings: mmc: convert rockchip dw-mshc bindings to yaml
dt-bindings: mmc: convert synopsys dw-mshc bindings to yaml
mmc: sdhci-msm: Add CQHCI support for sdhci-msm
mmc: sdhci: Let a vendor driver supply and update ADMA descriptor size
mmc: sdhci-of-esdhc: fix serious issue clock is always disabled
mmc: sdhci-of-esdhc: fix transfer mode register reading
mmc: sdhci-brcmstb: Fix incorrect switch to HS mode
mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)
mmc: sdhci-brcmstb: Add shutdown callback
mmc: sdhci-brcmstb: Fix driver to defer on clk_get defer
mmc: sdhci-brcmstb: Add ability to use HS400ES transfer mode
dt-bindings: mmc: brcm,sdhci-brcmstb: Add support for 7216b0
mmc: core: limit probe clock frequency to configured f_max
mmc: sdhci-milbeaut: Remove redundant platform_get_irq error message
mmc: sdhci: fix an issue of mixing different types
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Boris Brezillon:
"Core changes:
- Make i3c_bus_set_mode() static
Driver changes:
- Add a per-SoC data_hold_delay property to the Cadence driver
- Fix formatting issues in the 'CADENCE I3C MASTER IP' MAINTAINERS
entry
- Use devm_platform_ioremap_resource() where appropriate
- Adjust DesignWare reattach logic"
* tag 'i3c/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw: reattach device on first available location of address table
i3c: master: cdns: convert to devm_platform_ioremap_resource
i3c: master: dw: convert to devm_platform_ioremap_resource
MAINTAINERS: fix style in CADENCE I3C MASTER IP entry
i3c: master: make i3c_bus_set_mode static
i3c: master: cdns: add data hold delay support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS updates from Borislav Petkov:
- Misc fixes to the MCE code all over the place, by Jan H. Schönherr.
- Initial support for AMD F19h and other cleanups to amd64_edac, by
Yazen Ghannam.
- Other small cleanups.
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
EDAC/mce_amd: Make fam_ops static global
EDAC/amd64: Drop some family checks for newer systems
EDAC/amd64: Add family ops for Family 19h Models 00h-0Fh
x86/amd_nb: Add Family 19h PCI IDs
EDAC/mce_amd: Always load on SMCA systems
x86/MCE/AMD, EDAC/mce_amd: Add new Load Store unit McaType
x86/mce: Fix use of uninitialized MCE message string
x86/mce: Fix mce=nobootlog
x86/mce: Take action on UCNA/Deferred errors again
x86/mce: Remove mce_inject_log() in favor of mce_log()
x86/mce: Pass MCE message to mce_panic() on failed kernel recovery
x86/mce/therm_throt: Mark throttle_active_work() as __maybe_unused
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
"A totally boring branch this time around: a garden variety of small
fixes all over the place"
* tag 'edac_for_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Do not warn when removing instances
EDAC/sifive: Fix return value check in ecc_register()
EDAC/aspeed: Remove unneeded semicolon
EDAC: remove set but not used variable 'ecc_loc'
EDAC: skx_common: downgrade message importance on missing PCI device
EDAC/Kconfig: Fix Kconfig indentation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"core:
- Add support for enable attributes to hwmon core
- Add intrusion templates
pmbus:
- Support for Infineon Multi-phase xdpe122 family controllers
- Support for Intel IMVP9 and AMD 6.25mV modes
- Support for vid mode detection per page bases
- Detect if chip is write protected
- Support for MAX20730, MAX20734, MAX20743, MAX20796, UCD90320,
TPS53688
- Various improvements to ibm-cffps driver
k10temp:
- Support for additional temperature sensors as well as voltage and
current telemetry for Zen CPUs
w83627ehf:
- Remove support for NCT6775, NCT6776 (they have their own driver)
New drivers:
- ADM1177
- MAX31730
- Driver for disk and solid state drives with temperature sensors
Other:
- pwm-fan: stop fan on shutdown"
* tag 'hwmon-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (35 commits)
hwmon: (k10temp) Display up to eight sets of CCD temperatures
hwmon: (k10temp) Add debugfs support
hwmon: (k10temp) Don't show temperature limits on Ryzen (Zen) CPUs
hwmon: (k10temp) Show core and SoC current and voltages on Ryzen CPUs
hwmon: (k10temp) Report temperatures per CPU die
hmon: (k10temp) Convert to use devm_hwmon_device_register_with_info
hwmon: (k10temp) Use bitops
hwmon: (pwm-fan) stop fan on shutdown
MAINTAINERS: add entry for ADM1177 driver
dt-binding: hwmon: Add documentation for ADM1177
hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver
docs: hwmon: Include 'xdpe12284.rst' into docs
hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers
hwmon: (pmbus/tps53679) Extend device list supported by driver
hwmon: (pmbus/core) Add support for Intel IMVP9 and AMD 6.25mV modes
hwmon: (pmbus/core) Add support for vid mode detection per page bases
hwmon: (pmbus/ibm-cffps) Prevent writing on_off_config with bad data
hwmon: (w83627ehf) Remove set but not used variable 'fan4min'
hwmon: Driver for disk and solid state drives with temperature sensors
hwmon: (pmbus/ibm-cffps) Fix the LED behavior when turned off
...
|
|
Pull tpm updates from Jarkko Sakkinen:
"This adds a new sysfs file for querying TPM major version, which can
be used by the user space the TPM protocol used to communicate with
the chip"
* tag 'tpmdd-next-20200122' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: Add tpm_version_major sysfs file
tpm: Update mailing list contact information in sysfs-class-tpm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The changes are a real mixed bag this time around.
The only scary looking one from the diffstat is the uapi change to
asm-generic/mman-common.h, but this has been acked by Arnd and is
actually just adding a pair of comments in an attempt to prevent
allocation of some PROT values which tend to get used for
arch-specific purposes. We'll be using them for Branch Target
Identification (a CFI-like hardening feature), which is currently
under review on the mailing list.
New architecture features:
- Support for Armv8.5 E0PD, which benefits KASLR in the same way as
KPTI but without the overhead. This allows KPTI to be disabled on
CPUs that are not affected by Meltdown, even is KASLR is enabled.
- Initial support for the Armv8.5 RNG instructions, which claim to
provide access to a high bandwidth, cryptographically secure
hardware random number generator. As well as exposing these to
userspace, we also use them as part of the KASLR seed and to seed
the crng once all CPUs have come online.
- Advertise a bunch of new instructions to userspace, including
support for Data Gathering Hint, Matrix Multiply and 16-bit
floating point.
Kexec:
- Cleanups in preparation for relocating with the MMU enabled
- Support for loading crash dump kernels with kexec_file_load()
Perf and PMU drivers:
- Cleanups and non-critical fixes for a couple of system PMU drivers
FPU-less (aka broken) CPU support:
- Considerable fixes to support CPUs without the FP/SIMD extensions,
including their presence in heterogeneous systems. Good luck
finding a 64-bit userspace that handles this.
Modern assembly function annotations:
- Start migrating our use of ENTRY() and ENDPROC() over to the
new-fangled SYM_{CODE,FUNC}_{START,END} macros, which are intended
to aid debuggers
Kbuild:
- Cleanup detection of LSE support in the assembler by introducing
'as-instr'
- Remove compressed Image files when building clean targets
IP checksumming:
- Implement optimised IPv4 checksumming routine when hardware offload
is not in use. An IPv6 version is in the works, pending testing.
Hardware errata:
- Work around Cortex-A55 erratum #1530923
Shadow call stack:
- Work around some issues with Clang's integrated assembler not
liking our perfectly reasonable assembly code
- Avoid allocating the X18 register, so that it can be used to hold
the shadow call stack pointer in future
ACPI:
- Fix ID count checking in IORT code. This may regress broken
firmware that happened to work with the old implementation, in
which case we'll have to revert it and try something else
- Fix DAIF corruption on return from GHES handler with pseudo-NMIs
Miscellaneous:
- Whitelist some CPUs that are unaffected by Spectre-v2
- Reduce frequency of ASID rollover when KPTI is compiled in but
inactive
- Reserve a couple of arch-specific PROT flags that are already used
by Sparc and PowerPC and are planned for later use with BTI on
arm64
- Preparatory cleanup of our entry assembly code in preparation for
moving more of it into C later on
- Refactoring and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (73 commits)
arm64: acpi: fix DAIF manipulation with pNMI
arm64: kconfig: Fix alignment of E0PD help text
arm64: Use v8.5-RNG entropy for KASLR seed
arm64: Implement archrandom.h for ARMv8.5-RNG
arm64: kbuild: remove compressed images on 'make ARCH=arm64 (dist)clean'
arm64: entry: Avoid empty alternatives entries
arm64: Kconfig: select HAVE_FUTEX_CMPXCHG
arm64: csum: Fix pathological zero-length calls
arm64: entry: cleanup sp_el0 manipulation
arm64: entry: cleanup el0 svc handler naming
arm64: entry: mark all entry code as notrace
arm64: assembler: remove smp_dmb macro
arm64: assembler: remove inherit_daif macro
ACPI/IORT: Fix 'Number of IDs' handling in iort_id_map()
mm: Reserve asm-generic prot flags 0x10 and 0x20 for arch use
arm64: Use macros instead of hard-coded constants for MAIR_EL1
arm64: Add KRYO{3,4}XX CPU cores to spectre-v2 safe list
arm64: kernel: avoid x18 in __cpu_soft_restart
arm64: kvm: stop treating register x18 as caller save
arm64/lib: copy_page: avoid x18 register in assembler code
...
|
|
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
|
|
SPI NOR core changes:
- Add support for TB selection using SR bit 6,
- Add support for few flashes.
|
|
Fix the comment describing what the mtd_concat_destroy() function
does. It referrers to the concat_mtd_devs symbol which has never
existed (at least not since the beginning of the Git era).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently CONFIG_MTD_NAND_CADENCE implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/mtd/nand/raw/cadence-nand-controller.o: in function `cadence_nand_dt_probe.cold.31':
drivers/mtd/nand/raw/cadence-nand-controller.c:2969: undefined reference to `devm_platform_ioremap_resource'
ld: drivers/mtd/nand/raw/cadence-nand-controller.c:2977: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Page index use pgoff_t to prevent risk of truncation.
Signed-off-by: Liu Song <liu.song11@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add minimal runtime PM support (enable on probe, disable on remove), to
ensure proper operation with a parent device that uses runtime PM.
This is needed on systems where the FLASH is connected to a bus
controller that is contained in a PM domain and/or has a gateable
functional clock. In such cases, before accessing any device connected
to the external bus, the PM domain must be powered up, and/or the
functional clock must be enabled, which is typically handled through
runtime PM by the bus controller driver.
An example of this is the Renesas APE6-EVM development board, which has
an Ethernet controller and a CFI FLASH connected to the Bus State
Controller (BSC) of an R-Mobile APE6 SoC.
As long as the Ethernet driver, which had Runtime PM support since
commit 3a611e26e958b037 ("net/smsc911x: Add minimal runtime PM
support"), keeps the BSC powered, accessing the FLASH works.
When the ethernet node in r8a73a4-ape6evm.dts is disabled, the BSC is
never powered up, and the kernel crashes when trying to access the
FLASH:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=7fef2835
Internal error: : 1406 [#1] SMP ARM
CPU: 0 PID: 122 Comm: hd Tainted: G W 5.5.0-rc1-ape6evm-00814-g38ca966db25b9dbd-dirty #136
Hardware name: Generic R8A73A4 (Flattened Device Tree)
PC is at chip_ready+0x12c/0x380
LR is at chip_ready+0x10c/0x380
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
pcmciamtd_set_vpp()
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/pcmcia/pcmcia_resource.c, 312:
mutex_lock in pcmcia_fixup_vpp
drivers/mtd/maps/pcmciamtd.c, 309:
pcmcia_fixup_vpp in pcmciamtd_set_vpp
drivers/mtd/maps/pcmciamtd.c, 306:
_raw_spin_lock_irqsave in pcmciamtd_set_vpp
drivers/pcmcia/pcmcia_resource.c, 312:
mutex_lock in pcmcia_fixup_vpp
drivers/mtd/maps/pcmciamtd.c, 312:
pcmcia_fixup_vpp in pcmciamtd_set_vpp
drivers/mtd/maps/pcmciamtd.c, 306:
_raw_spin_lock_irqsave in pcmciamtd_set_vp
mutex_lock() may sleep at runtime.
To fix these bugs, the spinlock is replaced with a mutex.
These bugs are found by a static analysis tool STCheck written by
myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The rbd driver already provides additional information in sysfs
under /sys/bus/rbd, so we should set the 'device' link in the block
device to reference this information.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
gcc -O3 warns about a dummy variable that is passed
down into rbd_img_fill_nodata without being initialized:
drivers/block/rbd.c: In function 'rbd_img_fill_nodata':
drivers/block/rbd.c:2573:13: error: 'dummy' is used uninitialized in this function [-Werror=uninitialized]
fctx->iter = *fctx->pos;
Since this is a dummy, I assume the warning is harmless, but
it's better to initialize it anyway and avoid the warning.
Fixes: mmtom ("init/Kconfig: enable -O3 for all arches")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/late
DaVinci SoC updates for v5.6 include migrating DM365 SoC to use
drivers/clocksource based driver for timer. This leads to removal
of machine specific timer driver.
There are two patches adding missing fixed regulators for audio codecs
on DM365 and DM644x EVMs.
* tag 'davinci-for-v5.6/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm644x-evm: Add Fixed regulators needed for tlv320aic33
ARM: davinci: dm365-evm: Add Fixed regulators needed for tlv320aic3101
ARM: davinci: remove legacy timer support
ARM: davinci: dm365: switch to using the clocksource driver
clocksource: davinci: only enable clockevents once tim34 is initialized
Link: https://lore.kernel.org/r/043eb5b2-a302-4de6-a3e8-8238e49483b1@ti.com/
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The restart handler is executed during the shutdown phase which is
atomic/irq-less. The i2c framework supports atomic transfers since
commit 63b96983a5dd ("i2c: core: introduce callbacks for atomic
transfers") to address this use case. Using regmap within an atomic
context is allowed only if the regmap type is MMIO and the cache type
'flat' or no cache is used. Using the i2c_smbus_write_byte_data()
function can be done without additional tests because:
1) the DA9062 is an i2c-only device and
2) the i2c framework emulates the smbus protocol if the host adapter
does not support smbus_xfer by using the master_xfer.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stefan Lengfeld <contact@stefanchrist.eu>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200115162307.7336-1-m.felsch@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Add reset controller for 2712.
Besides watchdog, MTK toprgu module alsa provide sub-system (eg, audio,
camera, codec and connectivity) software reset functionality.
Signed-off-by: yong.liang <yong.liang@mediatek.com>
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200115085828.27791-5-yong.liang@mediatek.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Add reset controller API in watchdog driver.
Besides watchdog, MTK toprgu module alsa provide sub-system (eg, audio,
camera, codec and connectivity) software reset functionality.
Signed-off-by: yong.liang <yong.liang@mediatek.com>
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200115085828.27791-4-yong.liang@mediatek.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
IT8786 watchdog works as in IT872x
Tested on VECOW ECS-9000 board.
Signed-off-by: Vincent Prince <Vincent.PRINCE.fr@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200123140544.25937-1-vincent.prince.fr@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Currently on an rk3288 SoC when trying to use the watchdog the SoC will
instantly reset. This is due to the watchdog countdown counter being set
to its initial value of 0x0. Reset the watchdog counter before start in
order to correctly start the countdown timer from the right position.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200107155155.278521-1-ml@embed.me.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
After the commit 44ea39420fc9 ("drivers/watchdog: make use of
devm_register_reboot_notifier()") the struct notifier_block reboot_nb in
the struct watchdog_device is removed from the reboot notifiers chain at
the time watchdog's chardev is closed. But at least in i6300esb.c case
reboot_nb is embedded in the struct esb_dev which can be freed on its
device removal and before the chardev is closed, thus UAF at reboot:
[ 7.728581] esb_probe: esb_dev.watchdog_device ffff91316f91ab28
ts# uname -r note the address ^^^
5.5.0-rc5-ae6088-wdog
ts# ./openwdog0 &
[1] 696
ts# opened /dev/watchdog0, sleeping 10s...
ts# echo 1 > /sys/devices/pci0000\:00/0000\:00\:09.0/remove
[ 178.086079] devres:rel_nodes: dev ffff91317668a0b0 data ffff91316f91ab28
esb_dev.watchdog_device.reboot_nb memory is freed here ^^^
ts# ...woken up
[ 181.459010] devres:rel_nodes: dev ffff913171781000 data ffff913174a1dae8
[ 181.460195] devm_unreg_reboot_notifier: res ffff913174a1dae8 nb ffff91316f91ab78
attempt to use memory already freed ^^^
[ 181.461063] devm_unreg_reboot_notifier: nb->call 6b6b6b6b6b6b6b6b
[ 181.461243] devm_unreg_reboot_notifier: nb->next 6b6b6b6b6b6b6b6b
freed memory is filled with a slub poison ^^^
[1]+ Done ./openwdog0
ts# reboot
[ 229.921862] systemd-shutdown[1]: Rebooting.
[ 229.939265] notifier_call_chain: nb ffffffff9c6c2f20 nb->next ffffffff9c6d50c0
[ 229.943080] notifier_call_chain: nb ffffffff9c6d50c0 nb->next 6b6b6b6b6b6b6b6b
[ 229.946054] notifier_call_chain: nb 6b6b6b6b6b6b6b6b INVAL
[ 229.957584] general protection fault: 0000 [#1] SMP
[ 229.958770] CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.5.0-rc5-ae6088-wdog
[ 229.960224] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 229.963288] RIP: 0010:notifier_call_chain+0x66/0xd0
[ 229.969082] RSP: 0018:ffffb20dc0013d88 EFLAGS: 00010246
[ 229.970812] RAX: 000000000000002e RBX: 6b6b6b6b6b6b6b6b RCX: 00000000000008b3
[ 229.972929] RDX: 0000000000000000 RSI: 0000000000000096 RDI: ffffffff9ccc46ac
[ 229.975028] RBP: 0000000000000001 R08: 0000000000000000 R09: 00000000000008b3
[ 229.977039] R10: 0000000000000001 R11: ffffffff9c26c740 R12: 0000000000000000
[ 229.979155] R13: 6b6b6b6b6b6b6b6b R14: 0000000000000000 R15: 00000000fffffffa
... slub_debug=FZP poison ^^^
[ 229.989089] Call Trace:
[ 229.990157] blocking_notifier_call_chain+0x43/0x59
[ 229.991401] kernel_restart_prepare+0x14/0x30
[ 229.992607] kernel_restart+0x9/0x30
[ 229.993800] __do_sys_reboot+0x1d2/0x210
[ 230.000149] do_syscall_64+0x3d/0x130
[ 230.001277] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 230.002639] RIP: 0033:0x7f5461bdd177
[ 230.016402] Modules linked in: i6300esb
[ 230.050261] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Fix the crash by reverting 44ea39420fc9 so unregister_reboot_notifier()
is called when watchdog device is removed. This also makes handling of
the reboot notifier unified with the handling of the restart handler,
which is freed with unregister_restart_handler() in the same place.
Fixes: 44ea39420fc9 ("drivers/watchdog: make use of devm_register_reboot_notifier()")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200108125347.6067-1-vdronov@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
"%p" is not printing the pointer value.
In driver, printing pointer value is not useful so avoiding print.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1576825096-26605-1-git-send-email-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
platform_get_irq() prints an error message when the interrupt
is not available. So on platforms where bark interrupt is
not specified, following error message is observed on SDM845.
[ 2.975888] qcom_wdt 17980000.watchdog: IRQ index 0 not found
This is also seen on SC7180, SM8150 SoCs as well.
Fix this by using platform_get_irq_optional() instead.
Fixes: 36375491a4395654 ("watchdog: qcom: support pre-timeout when the bark irq is available")
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191213064934.4112-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Disable the watchdog during suspend if it is enabled and re-enable it on
resume. So we can sleep without the interruptions.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191128171931.22563-1-m.felsch@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
watchdog_dev.c provides means to allow users to set bigger timeout value
than HW can support, make DesignWare watchdog align with this.
Signed-off-by: Peng Wang <peng.1.wang@nokia-sbell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/8fa54e92c6cd4544a7a3eb60a373ac43@nokia-sbell.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
If the watchdog hardware is already enabled during the boot process,
when the Linux watchdog driver loads, it should start/reset the watchdog
and tell the watchdog framework. As a result, ping can be generated from
the watchdog framework (if CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is set),
until the userspace watchdog daemon takes over control
Fixes:4332d113c66a ("watchdog: Add STM32 IWDG driver")
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191122132246.8473-1-christophe.roullier@st.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Add support for SAM9X60 WDT into sama5d4_wdt.
This means that this driver gets a flag inside the data struct
that represents the sam9x60 support.
This flag differentiates between the two hardware blocks, and is set
according to the compatible of the driver instantiation.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1574067012-18559-3-git-send-email-eugen.hristev@microchip.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
- voltage support for newer Logitech HID++ devices, from Pedro Vanzella.
- MX Master support improvements, from Adrian Freund and Mazin Rezk
|
|
- support for uniq ioctl()
|
|
With the STM32 thermal peripheral, it is not possible to dump the
temperature that has caused the interrupt.
When the temperature reaches the low threshold, we generally read
a temperature that is a little bit higher than the low threshold.
This maybe due to sampling precision, and also because the CPU becomes
hotter when it quits WFI mode.
In that case, the framework does not change the trip points. This leads
to a lot of low threshold interrupts.
The fix is to set the low threshold value 0.5 degrees Celsius
below the actual request.
The problem is not so frequent with the high threshold and it would
no be a good idea to set the threshold value higher than the request.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-7-p.paillet@st.com
|
|
Change the way of computing to avoid rounds by 1 or 2 degrees.
Also simplify the sampling time management that is hard-coded
to maximum value during probe.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-6-p.paillet@st.com
|
|
Let the thermal framework handle the trip points instead
of custom code inside the driver. This is backward compatible,
simplifies the driver and offers the possibility to the user
to set any trip point he needs.
stm_thermal_set_trips callback that is registered to
set_trips ops to handle the low and high thresholds and replaces
stm_thermal_set_threshold and stm_thermal_update_threshold functions.
modify irq enable to handle the thresholds.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-5-p.paillet@st.com
|
|
In case of CPU reset, the interrupts could be enabled at boot time.
Disable interrupts and clear flags.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-4-p.paillet@st.com
|
|
Be sure get_temp returns an error while disabling or enabling the device.
Set THERMAL_DEVICE_ENABLED state at the end of power on function.
Set THERMAL_DEVICE_DISABLED state at the beginning of power off function.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-3-p.paillet@st.com
|
|
Fix a mistake with the ICIFR register name.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-2-p.paillet@st.com
|
|
OF node is missing
When devm_thermal_zone_of_sensor_register() is called from
hwmon_thermal_add_sensor() it is possible that the relevant sensor is
missing an OF node. In this case thermal_zone_of_sensor_register() returns
-EINVAL which causes hwmon_thermal_add_sensor() to fail as well. This patch
changes relevant return code of thermal_zone_of_sensor_register() to
-ENODEV, which is tolerated by hwmon_thermal_add_sensor().
Here is a particular case of such behaviour: the Marvell ethernet PHYs
driver registers hwmon device for the built-in temperature sensor (see
drivers/net/phy/marvell.c). Since the sensor doesn't have associated OF
node devm_hwmon_device_register() returns error which ultimately causes
failure of the PHY driver's probe function.
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20190827143952.19591-1-pmamonov@gmail.com
|
|
Commit e5e884b42639 ("libertas: Fix two buffer overflows at parsing bss
descriptor") introduced a bounds check on the number of supplied rates to
lbs_ibss_join_existing() and made it to return on overflow.
However, the aforementioned commit doesn't set the return value accordingly
and thus, lbs_ibss_join_existing() would return with zero even though it
failed.
Make lbs_ibss_join_existing return -EINVAL in case the bounds check on the
number of supplied rates fails.
Fixes: e5e884b42639 ("libertas: Fix two buffer overflows at parsing bss descriptor")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Commit e5e884b42639 ("libertas: Fix two buffer overflows at parsing bss
descriptor") introduced a bounds check on the number of supplied rates to
lbs_ibss_join_existing().
Unfortunately, it introduced a return path from within a RCU read side
critical section without a corresponding rcu_read_unlock(). Fix this.
Fixes: e5e884b42639 ("libertas: Fix two buffer overflows at parsing bss descriptor")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
mwifiex_cmd_append_vsie_tlv() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Qing Xu <m1s5p6688@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
mwifiex_ret_wmm_get_status() calls memcpy() without checking the
destination size.Since the source is given from remote AP which
contains illegal wmm elements , this may trigger a heap buffer
overflow.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Qing Xu <m1s5p6688@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We called rcu_read_lock(), so we need to call rcu_read_unlock() before
we return.
Fixes: 3d94a4a8373b ("mwifiex: fix possible heap overflow in mwifiex_process_country_ie()")
Cc: stable@vger.kernel.org
Cc: huangwen <huangwenabc@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add to debug dump more information on the platform it was collected
from (pci func, path id).
Provide human readable reg fifo erros.
Removed static debug arrays from HSI Functions, and move them to
the hwfn.
Some structures were slightly changed (removing reserved chip id
for example) which lead to many long initializations being modified
with one parameter less during initialization. This leads to
some long diffs that don't really change anything.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QM phase init tool can be invoked multiple times during
the driver lifetime. Part of the init comes from the runtime array.
The logic for setting the values did not init all values, basically
assuming the runtime array was all zeroes. But if it was invoked
multiple times, nobody was zeroing it after the first time.
In this change we zero the runtime array right after using it.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
