summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2023-10-07irqchip/stm32-exti: add missing DT IRQ flag translationBen Wolsieffer
The STM32F4/7 EXTI driver was missing the xlate callback, so IRQ trigger flags specified in the device tree were being ignored. This was preventing the RTC alarm interrupt from working, because it must be set to trigger on the rising edge to function correctly. Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20231003162003.1649967-1-ben.wolsieffer@hefring.com
2023-10-07irqchip/riscv-intc: Mark all INTC nodes as initializedAnup Patel
The RISC-V INTC local interrupts are per-HART (or per-CPU) so we create INTC IRQ domain only for the INTC node belonging to the boot HART. This means only the boot HART INTC node will be marked as initialized and other INTC nodes won't be marked which results downstream interrupt controllers (such as PLIC, IMSIC and APLIC direct-mode) not being probed due to missing device suppliers. To address this issue, we mark all INTC node for which we don't create IRQ domain as initialized. Reported-by: Dmitry Dunaev <dunaev@tecon.ru> Signed-off-by: Anup Patel <apatel@ventanamicro.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230926102801.1591126-1-dunaev@tecon.ru Link: https://lore.kernel.org/r/20231003044403.1974628-4-apatel@ventanamicro.com
2023-10-07irqchip/gic-v3: Enable non-coherent redistributors/ITSes DT probingLorenzo Pieralisi
The GIC architecture specification defines a set of registers for redistributors and ITSes that control the sharebility and cacheability attributes of redistributors/ITSes initiator ports on the interconnect (GICR_[V]PROPBASER, GICR_[V]PENDBASER, GITS_BASER<n>). Architecturally the GIC provides a means to drive shareability and cacheability attributes signals and related IWB/OWB/ISH barriers but it is not mandatory for designs to wire up the corresponding interconnect signals that control the cacheability/shareability of transactions. Redistributors and ITSes interconnect ports can be connected to non-coherent interconnects that are not able to manage the shareability/cacheability attributes; this implicitly makes the redistributors and ITSes non-coherent observers. So far, the GIC driver on probe executes a write to "probe" for the redistributors and ITSes registers shareability bitfields by writing a value (ie InnerShareable - the shareability domain the CPUs are in) and check it back to detect whether the value sticks or not; this hinges on a GIC programming model behaviour that predates the current specifications, that just define shareability bits as writeable but do not guarantee that writing certain shareability values enable the expected behaviour for the redistributors/ITSes memory interconnect ports. To enable non-coherent GIC designs, introduce the "dma-noncoherent" device tree property to allow firmware to describe redistributors and ITSes as non-coherent observers on the memory interconnect and use the property to force the shareability attributes to be programmed into the redistributors and ITSes registers through the GIC quirks mechanism. Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Marc Zyngier <maz@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20231006125929.48591-3-lpieralisi@kernel.org
2023-10-07irqchip/gic-v3-its: Split allocation from initialisation of its_nodeMarc Zyngier
In order to pave the way for more fancy quirk handling without making more of a mess of this terrible driver, split the allocation of the ITS descriptor (its_node) from the actual probing. This will allow firmware-specific hooks to be added between these two points. Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20231006125929.48591-4-lpieralisi@kernel.org
2023-10-07serial: core: Fix checks for tx runtime PM stateTony Lindgren
Maximilian reported that surface_serial_hub serdev tx does not work during system suspend. During system suspend, runtime PM gets disabled in __device_suspend_late(), and tx is unable to wake-up the serial core port device that we use to check if tx is safe to start. Johan summarized the regression noting that serdev tx no longer always works as earlier when the serdev device is runtime PM active. The serdev device and the serial core controller devices are siblings of the serial port hardware device. The runtime PM usage count from serdev device does not propagate to the serial core device siblings, it only propagates to the parent. In addition to the tx issue for suspend, testing for the serial core port device can cause an unnecessary delay in enabling tx while waiting for the serial core port device to wake-up. The serial core port device wake-up is only needed to flush pending tx when the serial port hardware device was in runtime PM suspended state. To fix the regression, we need to check the runtime PM state of the parent serial port hardware device for tx instead of the serial core port device. As the serial port device drivers may or may not implement runtime PM, we need to also add a check for pm_runtime_enabled(). Reported-by: Maximilian Luz <luzmaximilian@gmail.com> Cc: stable <stable@kernel.org> Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM") Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Maximilian Luz <luzmaximilian@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20231005075644.25936-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-10-06ravb: Fix use-after-free issue in ravb_tx_timeout_work()Yoshihiro Shimoda
The ravb_stop() should call cancel_work_sync(). Otherwise, ravb_tx_timeout_work() is possible to use the freed priv after ravb_remove() was called like below: CPU0 CPU1 ravb_tx_timeout() ravb_remove() unregister_netdev() free_netdev(ndev) // free priv ravb_tx_timeout_work() // use priv unregister_netdev() will call .ndo_stop() so that ravb_stop() is called. And, after phy_stop() is called, netif_carrier_off() is also called. So that .ndo_tx_timeout() will not be called after phy_stop(). Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Reported-by: Zheng Wang <zyytlz.wz@163.com> Closes: https://lore.kernel.org/netdev/20230725030026.1664873-1-zyytlz.wz@163.com/ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20231005011201.14368-3-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-10-06ravb: Fix up dma_free_coherent() call in ravb_remove()Yoshihiro Shimoda
In ravb_remove(), dma_free_coherent() should be call after unregister_netdev(). Otherwise, this controller is possible to use the freed buffer. Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20231005011201.14368-2-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-10-06Merge tag 'block-6.6-2023-10-06' of git://git.kernel.dk/linuxLinus Torvalds
Pull block fixes from Jens Axboe: "Just two minor fixes, for nbd and md" * tag 'block-6.6-2023-10-06' of git://git.kernel.dk/linux: nbd: don't call blk_mark_disk_dead nbd_clear_sock_ioctl md/raid5: release batch_last before waiting for another stripe_head
2023-10-06Merge tag 'renesas-fixes-for-v6.6-tag1' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes Renesas fixes for v6.6 - Fix RISC-V multi-platform kernels by excluding RZ/Five. * tag 'renesas-fixes-for-v6.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: soc: renesas: Make ARCH_R9A07G043 (riscv version) depend on NONPORTABLE Link: https://lore.kernel.org/r/cover.1696578170.git.geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2023-10-06Merge tag 'amdtee-fix-for-v6.6' of ↵Arnd Bergmann
https://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes AMDTEE fix possible use-after-free * tag 'amdtee-fix-for-v6.6' of https://git.linaro.org/people/jens.wiklander/linux-tee: tee: amdtee: fix use-after-free vulnerability in amdtee_close_session Link: https://lore.kernel.org/r/20231003171835.GA669924@rayden Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2023-10-06Merge tag 'pci-v6.6-fixes-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull PCI fixes from Bjorn Helgaas: - Fix a qcom register offset that broke IPQ8074 PCIe controller enumeration (Sricharan Ramabadhran) - Handle interrupt parsing failures when creating a device tree node to avoid using uninitialized data (Lizhi Hou) - Clean up if adding PCI device node fails when creating a device tree node to avoid a memory leak (Lizhi Hou) - If a link is down, mark all downstream devices as "disconnected" so we don't wait for them on resume (Mika Westerberg) * tag 'pci-v6.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: PCI/PM: Mark devices disconnected if upstream PCIe link is down on resume PCI: of: Destroy changeset when adding PCI device node fails PCI: of_property: Handle interrupt parsing failures PCI: qcom: Fix IPQ8074 enumeration
2023-10-06Merge tag 'platform-drivers-x86-v6.6-4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 Pull x86 platform driver fixes from Hans de Goede: "Bug fixes, build warning fixes and DMI quirk additions" * tag 'platform-drivers-x86-v6.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: platform/x86: hp-wmi:: Mark driver struct with __refdata to prevent section mismatch warning platform/x86: touchscreen_dmi: Add info for the Positivo C4128B platform/x86: touchscreen_dmi: Add info for the BUSH Bush Windows tablet platform/mellanox: tmfifo: fix kernel-doc warnings platform/x86/intel/ifs: release cpus_read_lock() platform/x86: hp-bioscfg: Fix reference leak platform/x86: think-lmi: Fix reference leak
2023-10-06Merge tag 'iio-fixes-for-6.6a' of ↵Greg Kroah-Hartman
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus Jonathan writes: 1st set of IIO fixes for 6.6 Note last minute rebase to fix up a stale Fixes tag. All patches have been in Linux-next for some time. adi,ad3552r - Fix swapped device IDs for the two parts that are supported. adi,ad7192 - Use the right reference voltage source. adi,ad7292 - Fix additionalProperties to be false, not true. adi,ad74413 - Add missing Kconfig depends on IIO_BUFFER and IIO_TRIGGERED_BUFFER adi,admv1013 - Fix up some corner cases for the mixer vgate register value. bosch,bmp280 - Fix a null pointer dereference caused by a wrong boolean operator. bosch,bno055 - Add missing Kconfig depends on IIO_BUFFER and IIO_TRIGGERED_BUFFER freescale,imx8eqxp - Fix some wrong register addresses. google,cros_ec - Fix a use after free if very badly timed buffer disable occurs by holding the device in buffered mode. infineon,dps310 - Expand a timeout so we don't hit it on working parts. meas,m5611 - Allow for a ROM CRC of 0 as it is a valid value and there are devices out there where it happens. murata,irsd200 - Make sure the buffer used to build up the scan is large enough to take the timestamp. rohm,bu27010 binding - Add a missing required vdd-supply vishay,vcnl4000 - Don't power down chip in wrong place. * tag 'iio-fixes-for-6.6a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: iio: pressure: ms5611: ms5611_prom_is_valid false negative bug dt-bindings: iio: adc: adi,ad7292: Fix additionalProperties on channel nodes iio: adc: ad7192: Correct reference voltage iio: light: vcnl4000: Don't power on/off chip in config iio: addac: Kconfig: update ad74413r selections iio: pressure: dps310: Adjust Timeout Settings iio: imu: bno055: Fix missing Kconfig dependencies iio: adc: imx8qxp: Fix address for command buffer registers iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data() iio: irsd200: fix -Warray-bounds bug in irsd200_trigger_handler dt-bindings: iio: rohm,bu27010: add missing vdd-supply to example iio: admv1013: add mixer_vgate corner cases iio: pressure: bmp280: Fix NULL pointer exception iio: dac: ad3552r: Correct device IDs
2023-10-06Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Will Deacon: "A typo fix for a PMU driver, a workround for a side-channel erratum on Cortex-A520 and a fix for the local timer save/restore when using ACPI with Qualcomm's custom CPUs: - Workaround for Cortex-A520 erratum #2966298 - Fix typo in Arm CMN PMU driver that breaks counter overflow handling - Fix timer handling across idle for Qualcomm custom CPUs" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: cpuidle, ACPI: Evaluate LPI arch_flags for broadcast timer arm64: errata: Add Cortex-A520 speculative unprivileged load workaround arm64: Add Cortex-A520 CPU part definition perf/arm-cmn: Fix the unhandled overflow status of counter 4 to 7
2023-10-06Merge tag 'drm-fixes-2023-10-06' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm fixes from Dave Airlie: "Regular weekly pull, all seems pretty normal, i915 and amdgpu mostly. There is one small new uAPI addition for nouveau but getting it in now avoids a bunch of userspace dances, and it's for a userspace that hasn't yet released, so should have no side effects. i915: - Fix for OpenGL CTS regression on Compute Shaders - Fix for default engines initialization - Fix TLB invalidation for Multi-GT devices amdgpu: - Add missing unique_id for GC 11.0.3 - Fix memory leak in FRU error path - Fix PCIe link reporting on some SMU 11 parts - Fix ACPI _PR3 detection - Fix DISPCLK WDIVIDER handling in OTG code tests: - Fix kunit release panel: - panel-orientation: Add quirk for One Mix 25 nouveau: - Report IB limit via getparams - Replace some magic numbers with constants - small clean up" * tag 'drm-fixes-2023-10-06' of git://anongit.freedesktop.org/drm/drm: drm/amd/display: apply edge-case DISPCLK WDIVIDER changes to master OTG pipes only drm/amd: Fix detection of _PR3 on the PCIe root port drm/amd: Fix logic error in sienna_cichlid_update_pcie_parameters() drm/amdgpu: Fix a memory leak drm/amd/pm: add unique_id for gc 11.0.3 drm/i915: Invalidate the TLBs on each GT drm/i915: Register engines early to avoid type confusion drm/i915: Don't set PIPE_CONTROL_FLUSH_L3 for aux inval drm/nouveau: exec: report max pushs through getparam drm/nouveau: chan: use channel class definitions drm/nouveau: chan: use struct nvif_mclass drm: panel-orientation-quirks: Add quirk for One Mix 2S drm/tests: Fix kunit_release_action ctx argument
2023-10-06HID: logitech-hidpp: Fix kernel crash on receiver USB disconnectHans de Goede
hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU) races when it races with itself. hidpp_connect_event() primarily runs from a workqueue but it also runs on probe() and if a "device-connected" packet is received by the hw when the thread running hidpp_connect_event() from probe() is waiting on the hw, then a second thread running hidpp_connect_event() will be started from the workqueue. This opens the following races (note the below code is simplified): 1. Retrieving + printing the protocol (harmless race): if (!hidpp->protocol_major) { hidpp_root_get_protocol_version() hidpp->protocol_major = response.rap.params[0]; } We can actually see this race hit in the dmesg in the abrt output attached to rhbz#2227968: [ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected. [ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected. Testing with extra logging added has shown that after this the 2 threads take turn grabbing the hw access mutex (send_mutex) so they ping-pong through all the other TOCTOU cases managing to hit all of them: 2. Updating the name to the HIDPP name (harmless race): if (hidpp->name == hdev->name) { ... hidpp->name = new_name; } 3. Initializing the power_supply class for the battery (problematic!): hidpp_initialize_battery() { if (hidpp->battery.ps) return 0; probe_battery(); /* Blocks, threads take turns executing this */ hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); } 4. Creating delayed input_device (potentially problematic): if (hidpp->delayed_input) return; hidpp->delayed_input = hidpp_allocate_input(hdev); The really big problem here is 3. Hitting the race leads to the following sequence: hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); ... hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); So now we have registered 2 power supplies for the same battery, which looks a bit weird from userspace's pov but this is not even the really big problem. Notice how: 1. This is all devm-maganaged 2. The hidpp->battery.desc struct is shared between the 2 power supplies 3. hidpp->battery.desc.properties points to the result from the second devm_kmemdup() This causes a use after free scenario on USB disconnect of the receiver: 1. The last registered power supply class device gets unregistered 2. The memory from the last devm_kmemdup() call gets freed, hidpp->battery.desc.properties now points to freed memory 3. The first registered power supply class device gets unregistered, this involves sending a remove uevent to userspace which invokes power_supply_uevent() to fill the uevent data 4. power_supply_uevent() uses hidpp->battery.desc.properties which now points to freed memory leading to backtraces like this one: Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08 ... Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0 ... Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30 Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0 Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0 Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0 Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680 Sep 22 20:01:35 eric kernel: power_supply_unregister+0x8e/0xa0 Sep 22 20:01:35 eric kernel: release_nodes+0x3d/0xb0 Sep 22 20:01:35 eric kernel: devres_release_group+0xfc/0x130 Sep 22 20:01:35 eric kernel: hid_device_remove+0x56/0xa0 Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200 Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130 Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0 Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440 Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60 Sep 22 20:01:35 eric kernel: logi_dj_remove+0x9a/0x100 [hid_logitech_dj 5c91534a0ead2b65e04dd799a0437e3b99b21bc4] Sep 22 20:01:35 eric kernel: hid_device_remove+0x44/0xa0 Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200 Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130 Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0 Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440 Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60 Sep 22 20:01:35 eric kernel: usbhid_disconnect+0x47/0x60 [usbhid 727dcc1c0b94e6b4418727a468398ac3bca492f3] Sep 22 20:01:35 eric kernel: usb_unbind_interface+0x90/0x270 Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200 Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130 Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0 Sep 22 20:01:35 eric kernel: ? kobject_put+0xa0/0x1d0 Sep 22 20:01:35 eric kernel: usb_disable_device+0xcd/0x1e0 Sep 22 20:01:35 eric kernel: usb_disconnect+0xde/0x2c0 Sep 22 20:01:35 eric kernel: usb_disconnect+0xc3/0x2c0 Sep 22 20:01:35 eric kernel: hub_event+0xe80/0x1c10 There have been quite a few bug reports (see Link tags) about this crash. Fix all the TOCTOU issues, including the really bad power-supply related system crash on USB disconnect, by making probe() use the workqueue for running hidpp_connect_event() too, so that it can never run more then once. Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227221 Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968 Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968 Link: https://bugzilla.redhat.com/show_bug.cgi?id=2242189 Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412#c58 Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20231005182638.3776-1-hdegoede@redhat.com Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
2023-10-06platform: mellanox: Fix a resource leak in an error handling path in probing ↵Vadim Pasternak
flow Fix missed resource deallocation in rollback flows. Currently if an error occurs after a successful mlxplat_i2c_main_init(), mlxplat_i2c_main_exit() call is missed in rollback flow. Thus, some resources are not de-allocated. Move mlxplat_pre_exit() call from mlxplat_remove() into mlxplat_i2c_main_exit(). Call mlxplat_i2c_main_exit() instead of calling mlxplat_pre_exit() in mlxplat_probe() error handling flow. Unregister 'priv->pdev_i2c' device in mlxplat_i2c_main_init() cleanup flow if this device was successfully registered. Fixes: 158cd8320776 ("platform: mellanox: Split logic in init and exit flow") Reported-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Closes: https://lore.kernel.org/lkml/70165032-796e-6f5c-6748-f514e3b9d08c@linux.intel.com/T/ Signed-off-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20231005075616.42777-2-vadimp@nvidia.com Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2023-10-06platform/x86: hp-wmi:: Mark driver struct with __refdata to prevent section ↵Uwe Kleine-König
mismatch warning As described in the added code comment, a reference to .exit.text is ok for drivers registered via module_platform_driver_probe(). Make this explicit to prevent a section mismatch warning: WARNING: modpost: drivers/platform/x86/hp/hp-wmi: section mismatch in reference: hp_wmi_driver+0x8 (section: .data) -> hp_wmi_bios_remove (section: .exit.text) Fixes: c165b80cfecc ("hp-wmi: fix handling of platform device") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20231004111624.2667753-1-u.kleine-koenig@pengutronix.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-10-06can: flexcan: remove the auto stop mode for IMX93Haibo Chen
IMX93 A0 chip involve the internal q-channel handshake in LPCG and CCM to automatically handle the Flex-CAN IPG STOP signal. Only after FLEX-CAN enter stop mode then can support the self-wakeup feature. But meet issue when do the continue system PM stress test. When config the CAN as wakeup source, the first time after system suspend, any data on CAN bus can wakeup the system, this is as expect. But the second time when system suspend, data on CAN bus can't wakeup the system. If continue this test, we find in odd time system enter suspend, CAN can wakeup the system, but in even number system enter suspend, CAN can't wakeup the system. IC find a bug in the auto stop mode logic, and can't fix it easily. So for the new imx93 A1, IC drop the auto stop mode and involve the GPR to support stop mode (used before). IC define a bit in GPR which can trigger the IPG STOP signal to Flex-CAN, let it go into stop mode. And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR to imx93. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Link: https://lore.kernel.org/all/20230726112458.3524165-2-haibo.chen@nxp.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-10-06can: tcan4x5x: Fix id2_register for tcan4553Markus Schneider-Pargmann
Fix id2_register content for tcan4553. This slipped through my testing. Reported-by: Sean Anderson <sean.anderson@seco.com> Closes: https://lore.kernel.org/lkml/a94e6fc8-4f08-7877-2ba0-29b9c2780136@seco.com/ Fixes: 142c6dc6d9d7 ("can: tcan4x5x: Add support for tcan4552/4553") Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/all/20230919095401.1312259-1-msp@baylibre.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-10-06can: sja1000: Always restart the Tx queue after an overrunMiquel Raynal
Upstream commit 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs") fixes an issue with Renesas own SJA1000 CAN controller reception: the Rx buffer is only 5 messages long, so when the bus loaded (eg. a message every 50us), overrun may easily happen. Upon an overrun situation, due to a possible internal crosstalk situation, the controller enters a frozen state which only can be unlocked with a soft reset (experimentally). The solution was to offload a call to sja1000_start() in a threaded handler. This needs to happen in process context as this operation requires to sleep. sja1000_start() basically enters "reset mode", performs a proper software reset and returns back into "normal mode". Since this fix was introduced, we no longer observe any stalls in reception. However it was sporadically observed that the transmit path would now freeze. Further investigation blamed the fix mentioned above, and especially the reset operation. Reproducing the reset in a loop helped identifying what could possibly go wrong. The sja1000 is a single Tx queue device, which leverages the netdev helpers to process one Tx message at a time. The logic is: the queue is stopped, the message sent to the transceiver, once properly transmitted the controller sets a status bit which triggers an interrupt, in the interrupt handler the transmission status is checked and the queue woken up. Unfortunately, if an overrun happens, we might perform the soft reset precisely between the transmission of the buffer to the transceiver and the advent of the transmission status bit. We would then stop the transmission operation without re-enabling the queue, leading to all further transmissions to be ignored. The reset interrupt can only happen while the device is "open", and after a reset we anyway want to resume normal operations, no matter if a packet to transmit got dropped in the process, so we shall wake up the queue. Restarting the device and waking-up the queue is exactly what sja1000_set_mode(CAN_MODE_START) does. In order to be consistent about the queue state, we must acquire a lock both in the reset handler and in the transmit path to ensure serialization of both operations. It turns out, a lock is already held when entering the transmit path, so we can just acquire/release it as well with the regular net helpers inside the threaded interrupt handler and this way we should be safe. As the reset handler might still be called after the transmission of a frame to the transceiver but before it actually gets transmitted, we must ensure we don't leak the skb, so we free it (the behavior is consistent, no matter if there was an skb on the stack or not). Fixes: 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs") Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/all/20231002160206.190953-1-miquel.raynal@bootlin.com [mkl: fixed call to can_free_echo_skb()] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-10-06can: sun4i_can: Only show Kconfig if ARCH_SUNXI is setJohn Watts
When adding the RISCV option I didn't gate it behind ARCH_SUNXI. As a result this option shows up with Allwinner support isn't enabled. Fix that by requiring ARCH_SUNXI to be set if RISCV is set. Fixes: 8abb95250ae6 ("can: sun4i_can: Add support for the Allwinner D1") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Closes: https://lore.kernel.org/linux-sunxi/CAMuHMdV2m54UAH0X2dG7stEg=grFihrdsz4+o7=_DpBMhjTbkw@mail.gmail.com/ Signed-off-by: John Watts <contact@jookia.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/all/20230905231342.2042759-2-contact@jookia.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-10-06net: dsa: qca8k: fix potential MDIO bus conflict when accessing internal ↵Marek Behún
PHYs via management frames Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus also Micron ethernet PHY (dedicated to the WAN port). We've been experiencing a strange behavior of the WAN ethernet interface, wherein the WAN PHY started timing out the MDIO accesses, for example when the interface was brought down and then back up. Bisecting led to commit 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet"), which added support to access the QCA8337 switch's internal PHYs via management ethernet frames. Connecting the MDIO bus pins onto an oscilloscope, I was able to see that the MDIO bus was active whenever a request to read/write an internal PHY register was done via an management ethernet frame. My theory is that when the switch core always communicates with the internal PHYs via the MDIO bus, even when externally we request the access via ethernet. This MDIO bus is the same one via which the switch and internal PHYs are accessible to the board, and the board may have other devices connected on this bus. An ASCII illustration may give more insight: +---------+ +----| | | | WAN PHY | | +--| | | | +---------+ | | | | +----------------------------------+ | | | QCA8337 | MDC | | | +-------+ | ------o-+--|--------o------------o--| | | MDIO | | | | | PHY 1 |-|--to RJ45 --------o--|---o----+---------o--+--| | | | | | | | +-------+ | | +-------------+ | o--| | | | | MDIO MDC | | | | PHY 2 |-|--to RJ45 eth1 | | | o--+--| | | -----------|-|port0 | | | +-------+ | | | | | o--| | | | | switch core | | | | PHY 3 |-|--to RJ45 | +-------------+ o--+--| | | | | | +-------+ | | | o--| ... | | +----------------------------------+ When we send a request to read an internal PHY register via an ethernet management frame via eth1, the switch core receives the ethernet frame on port 0 and then communicates with the internal PHY via MDIO. At this time, other potential devices, such as the WAN PHY on Turris 1.x, cannot use the MDIO bus, since it may cause a bus conflict. Fix this issue by locking the MDIO bus even when we are accessing the PHY registers via ethernet management frames. Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet") Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-10-06net: dsa: qca8k: fix regmap bulk read/write methods on big endian systemsMarek Behún
Commit c766e077d927 ("net: dsa: qca8k: convert to regmap read/write API") introduced bulk read/write methods to qca8k's regmap. The regmap bulk read/write methods get the register address in a buffer passed as a void pointer parameter (the same buffer contains also the read/written values). The register address occupies only as many bytes as it requires at the beginning of this buffer. For example if the .reg_bits member in regmap_config is 16 (as is the case for this driver), the register address occupies only the first 2 bytes in this buffer, so it can be cast to u16. But the original commit implementing these bulk read/write methods cast the buffer to u32: u32 reg = *(u32 *)reg_buf & U16_MAX; taking the first 4 bytes. This works on little endian systems where the first 2 bytes of the buffer correspond to the low 16-bits, but it obviously cannot work on big endian systems. Fix this by casting the beginning of the buffer to u16 as u32 reg = *(u16 *)reg_buf; Fixes: c766e077d927 ("net: dsa: qca8k: convert to regmap read/write API") Signed-off-by: Marek Behún <kabel@kernel.org> Tested-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-10-06phy: lynx-28g: serialize concurrent phy_set_mode_ext() calls to shared registersVladimir Oltean
The protocol converter configuration registers PCC8, PCCC, PCCD (implemented by the driver), as well as others, control protocol converters from multiple lanes (each represented as a different struct phy). So, if there are simultaneous calls to phy_set_mode_ext() to lanes sharing the same PCC register (either for the "old" or for the "new" protocol), corruption of the values programmed to hardware is possible, because lynx_28g_rmw() has no locking. Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take the global spinlock from the phy_ops :: set_mode() implementation. There are no other callers which modify PCC registers. Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-10-06phy: lynx-28g: lock PHY while performing CDR lock workaroundVladimir Oltean
lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset the lane receiver if the CDR has not locked onto bit transitions in the RX stream. But the PHY consumer may do stuff with the PHY simultaneously, and that isn't okay. Block concurrent generic PHY calls by holding the PHY mutex from this workqueue. Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-10-06phy: lynx-28g: cancel the CDR check work item on the remove pathIoana Ciornei
The blamed commit added the CDR check work item but didn't cancel it on the remove path. Fix this by adding a remove function which takes care of it. Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-10-06HID: i2c-hid: fix handling of unpopulated devicesJohan Hovold
A recent commit reordered probe so that the interrupt line is now requested before making sure that the device exists. This breaks machines like the Lenovo ThinkPad X13s which rely on the HID driver to probe second-source devices and only register the variant that is actually populated. Specifically, the interrupt line may now already be (temporarily) claimed when doing asynchronous probing of the touchpad: genirq: Flags mismatch irq 191. 00082008 (hid-over-i2c) vs. 00082008 (hid-over-i2c) i2c_hid_of 21-0015: Could not register for hid-over-i2c interrupt, irq = 191, ret = -16 i2c_hid_of: probe of 21-0015 failed with error -16 Fix this by restoring the old behaviour of first making sure the device exists before requesting the interrupt line. Note that something like this should probably be implemented also for "panel followers", whose actual probe is currently effectively deferred until the DRM panel is probed (e.g. by powering down the device after making sure it exists and only then register it as a follower). Fixes: 675cd877c952 ("HID: i2c-hid: Rearrange probe() to power things up later") Cc: Douglas Anderson <dianders@chromium.org> Cc: Maxime Ripard <mripard@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Dennis Gilmore <dgilmore@redhat.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20231002155857.24584-1-johan+linaro@kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
2023-10-05Merge tag 'for-linus-2023100502' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid Pull HID fixes from Jiri Kosina: - power management fix for intel-ish-hid (Srinivas Pandruvada) - power management fix for hid-nintendo (Martino Fontana) - error handling fixes for nvidia-shield (Christophe JAILLET) - memory leak fix for hid-sony (Christophe JAILLET) - fix for slab out-of-bound write in hid-holtek (Ma Ke) - other assorted smaller fixes and device ID / quirk entry additions * tag 'for-linus-2023100502' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: HID: Add quirk to ignore the touchscreen battery on HP ENVY 15-eu0556ng HID: intel-ish-hid: ipc: Disable and reenable ACPI GPE bit HID: sony: remove duplicate NULL check before calling usb_free_urb() HID: nintendo: reinitialize USB Pro Controller after resuming from suspend HID: nvidia-shield: Fix some missing function calls() in the probe error handling path HID: nvidia-shield: Fix a missing led_classdev_unregister() in the probe error handling path HID: multitouch: Add required quirk for Synaptics 0xcd7e device HID: nvidia-shield: Select POWER_SUPPLY Kconfig option HID: holtek: fix slab-out-of-bounds Write in holtek_kbd_input_event HID: nvidia-shield: add LEDS_CLASS dependency HID: logitech-hidpp: Add Bluetooth ID for the Logitech M720 Triathlon mouse HID: steelseries: Fix signedness bug in steelseries_headset_arctis_1_fetch_battery() HID: sony: Fix a potential memory leak in sony_probe()
2023-10-06Merge tag 'drm-misc-fixes-2023-10-05' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes Short summary of fixes pull: * test: Fix kunit release * panel-orientation: Add quirk for One Mix 25 * nouveau: * Report IB limit via getparams * Replace some magic numbers with constants * Clean up Signed-off-by: Dave Airlie <airlied@redhat.com> From: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20231005092632.GA17332@linux-uq9g
2023-10-06Merge tag 'amd-drm-fixes-6.6-2023-10-04' of ↵Dave Airlie
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes amd-drm-fixes-6.6-2023-10-04: amdgpu: - Add missing unique_id for GC 11.0.3 - Fix memory leak in FRU error path - Fix PCIe link reporting on some SMU 11 parts - Fix ACPI _PR3 detection - Fix DISPCLK WDIVIDER handling in OTG code Signed-off-by: Dave Airlie <airlied@redhat.com> From: Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231005034358.7824-1-alexander.deucher@amd.com
2023-10-06dm crypt: Fix reqsize in crypt_iv_eboiv_genHerbert Xu
A skcipher_request object is made up of struct skcipher_request followed by a variable-sized trailer. The allocation of the skcipher_request and IV in crypt_iv_eboiv_gen is missing the memory for struct skcipher_request. Fix it by adding it to reqsize. Fixes: e3023094dffb ("dm crypt: Avoid using MAX_CIPHER_BLOCKSIZE") Cc: <stable@vger.kernel.org> #6.5+ Reported-by: Tatu Heikkilä <tatu.heikkila@gmail.com> Reviewed-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-10-05platform/x86: touchscreen_dmi: Add info for the Positivo C4128BRenan Guilherme Lebre Ramos
Add information for the Positivo C4128B, a notebook/tablet convertible. Link: https://github.com/onitake/gsl-firmware/pull/217 Signed-off-by: Renan Guilherme Lebre Ramos <japareaggae@gmail.com> Link: https://lore.kernel.org/r/20231004235900.426240-1-japareaggae@gmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-10-05Merge tag 'net-6.6-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from Bluetooth, netfilter, BPF and WiFi. I didn't collect precise data but feels like we've got a lot of 6.5 fixes here. WiFi fixes are most user-awaited. Current release - regressions: - Bluetooth: fix hci_link_tx_to RCU lock usage Current release - new code bugs: - bpf: mprog: fix maximum program check on mprog attachment - eth: ti: icssg-prueth: fix signedness bug in prueth_init_tx_chns() Previous releases - regressions: - ipv6: tcp: add a missing nf_reset_ct() in 3WHS handling - vringh: don't use vringh_kiov_advance() in vringh_iov_xfer(), it doesn't handle zero length like we expected - wifi: - cfg80211: fix cqm_config access race, fix crashes with brcmfmac - iwlwifi: mvm: handle PS changes in vif_cfg_changed - mac80211: fix mesh id corruption on 32 bit systems - mt76: mt76x02: fix MT76x0 external LNA gain handling - Bluetooth: fix handling of HCI_QUIRK_STRICT_DUPLICATE_FILTER - l2tp: fix handling of transhdrlen in __ip{,6}_append_data() - dsa: mv88e6xxx: avoid EEPROM timeout when EEPROM is absent - eth: stmmac: fix the incorrect parameter after refactoring Previous releases - always broken: - net: replace calls to sock->ops->connect() with kernel_connect(), prevent address rewrite in kernel_bind(); otherwise BPF hooks may modify arguments, unexpectedly to the caller - tcp: fix delayed ACKs when reads and writes align with MSS - bpf: - verifier: unconditionally reset backtrack_state masks on global func exit - s390: let arch_prepare_bpf_trampoline return program size, fix struct_ops offsets - sockmap: fix accounting of available bytes in presence of PEEKs - sockmap: reject sk_msg egress redirects to non-TCP sockets - ipv4/fib: send netlink notify when delete source address routes - ethtool: plca: fix width of reads when parsing netlink commands - netfilter: nft_payload: rebuild vlan header on h_proto access - Bluetooth: hci_codec: fix leaking memory of local_codecs - eth: intel: ice: always add legacy 32byte RXDID in supported_rxdids - eth: stmmac: - dwmac-stm32: fix resume on STM32 MCU - remove buggy and unneeded stmmac_poll_controller, depend on NAPI - ibmveth: always recompute TCP pseudo-header checksum, fix use of the driver with Open vSwitch - wifi: - rtw88: rtw8723d: fix MAC address offset in EEPROM - mt76: fix lock dependency problem for wed_lock - mwifiex: sanity check data reported by the device - iwlwifi: ensure ack flag is properly cleared - iwlwifi: mvm: fix a memory corruption due to bad pointer arithm - iwlwifi: mvm: fix incorrect usage of scan API Misc: - wifi: mac80211: work around Cisco AP 9115 VHT MPDU length" * tag 'net-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits) MAINTAINERS: update Matthieu's email address mptcp: userspace pm allow creating id 0 subflow mptcp: fix delegated action races net: stmmac: remove unneeded stmmac_poll_controller net: lan743x: also select PHYLIB net: ethernet: mediatek: disable irq before schedule napi net: mana: Fix oversized sge0 for GSO packets net: mana: Fix the tso_bytes calculation net: mana: Fix TX CQE error handling netlink: annotate data-races around sk->sk_err sctp: update hb timer immediately after users change hb_interval sctp: update transport state when processing a dupcook packet tcp: fix delayed ACKs for MSS boundary condition tcp: fix quick-ack counting to count actual ACKs of new data page_pool: fix documentation typos tipc: fix a potential deadlock on &tx->lock net: stmmac: dwmac-stm32: fix resume on STM32 MCU ipv4: Set offload_failed flag in fibmatch results netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure netfilter: nf_tables: Deduplicate nft_register_obj audit logs ...
2023-10-05Merge tag 'leds-fixes-6.6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds Pull LED fix from Lee Jones: "Just the one bug-fix: - Fix regression affecting LED_COLOR_ID_MULTI users" * tag 'leds-fixes-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: leds: Drop BUG_ON check for LED_COLOR_ID_MULTI
2023-10-05Merge tag 'mfd-fixes-6.6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd Pull MFD fixes from Lee Jones: "A couple of small fixes: - Potential build failure in CS42L43 - Device Tree bindings clean-up for a superseded patch" * tag 'mfd-fixes-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: dt-bindings: mfd: Revert "dt-bindings: mfd: maxim,max77693: Add USB connector" mfd: cs42l43: Fix MFD_CS42L43 dependency on REGMAP_IRQ
2023-10-05drm/msm/dpu: fail dpu_plane_atomic_check() based on mdp clk limitsAbhinav Kumar
Currently, dpu_plane_atomic_check() does not check whether the plane can process the image without exceeding the per chipset limits for MDP clock. This leads to underflow issues because the SSPP is not able to complete the processing for the data rate of the display. Fail the dpu_plane_atomic_check() if the SSPP cannot process the image without exceeding the MDP clock limits. changes in v2: - use crtc_state's adjusted_mode instead of mode Fixes: 25fdd5933e4c ("drm/msm: Add SDM845 DPU support") Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/556819/ Link: https://lore.kernel.org/r/20230911221627.9569-1-quic_abhinavk@quicinc.com
2023-10-05iio: pressure: ms5611: ms5611_prom_is_valid false negative bugAlexander Zangerl
The ms5611 driver falsely rejects lots of MS5607-02BA03-50 chips with "PROM integrity check failed" because it doesn't accept a prom crc value of zero as legitimate. According to the datasheet for this chip (and the manufacturer's application note about the PROM CRC), none of the possible values for the CRC are excluded - but the current code in ms5611_prom_is_valid() ends with return crc_orig != 0x0000 && crc == crc_orig Discussed with the driver author (Tomasz Duszynski) and he indicated that at that time (2015) he was dealing with some faulty chip samples which returned blank data under some circumstances and/or followed example code which indicated CRC zero being bad. As far as I can tell this exception should not be applied anymore; We've got a few hundred custom boards here with this chip where large numbers of the prom have a legitimate CRC value 0, and do work fine, but which the current driver code wrongly rejects. Signed-off-by: Alexander Zangerl <az@breathe-safe.com> Fixes: c0644160a8b5 ("iio: pressure: add support for MS5611 pressure and temperature sensor") Link: https://lore.kernel.org/r/2535-1695168070.831792@Ze3y.dhYT.s3fx Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05iio: adc: ad7192: Correct reference voltageAlisa-Dariana Roman
The avdd and the reference voltage are two different sources but the reference voltage was assigned according to the avdd supply. Add vref regulator structure and set the reference voltage according to the vref supply from the devicetree. In case vref supply is missing, reference voltage is set according to the avdd supply for compatibility with old devicetrees. Fixes: b581f748cce0 ("staging: iio: adc: ad7192: move out of staging") Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230924152149.41884-1-alisadariana@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05iio: light: vcnl4000: Don't power on/off chip in configMårten Lindahl
After enabling/disabling interrupts on the vcnl4040 chip the als and/or ps sensor is powered on or off depending on the interrupt enable bits. This is made as a last step in write_event_config. But there is no reason to do this as the runtime PM handles the power state of the sensors. Interfering with this may impact sensor readings. Consider the following: 1. Userspace makes sensor data reading which triggers RPM resume (sensor powered on) and a RPM suspend timeout. The timeout is 2000ms before RPM suspend powers the sensor off if no new reading is made within the timeout period. 2. Userspace disables interrupts => powers sensor off 3. Userspace reads sensor data = 0 because sensor is off and the suspend timeout has not passed. For each new reading made within the timeout period the timeout is renewed with 2000ms and RPM will not make a new resume (device was not suspended). So the sensor will not be powered on. 4. No further userspace reading for 2000ms ends RPM suspend timeout and triggers suspend (powers off already powered off sensor). Powering sensor off in (2) makes all consecutive readings made within 2000ms to the previous reading (3) return invalid data. Skip setting power state when writing new event config. Fixes: 546676121cb9 ("iio: light: vcnl4000: Add interrupt support for vcnl4040") Fixes: bc292aaf9cb4 ("iio: light: vcnl4000: add illuminance irq vcnl4040/4200") Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com> Link: https://lore.kernel.org/r/20230907-vcnl4000-pm-fix-v2-1-298e01f54db4@axis.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05iio: addac: Kconfig: update ad74413r selectionsAntoniu Miclaus
Building ad74413r without selecting IIO_BUFFER and IIO_TRIGGERED_BUFFER generates error with respect to the iio trigger functions that are used within the driver. Update the Kconfig accordingly. Fixes: fea251b6a5db ("iio: addac: add AD74413R driver") Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com> Link: https://lore.kernel.org/r/20230912085421.51102-1-antoniu.miclaus@analog.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05iio: pressure: dps310: Adjust Timeout SettingsLakshmi Yadlapati
The DPS310 sensor chip has been encountering intermittent errors while reading the sensor device across various system designs. This issue causes the chip to become "stuck," preventing the indication of "ready" status for pressure and temperature measurements in the MEAS_CFG register. To address this issue, this commit fixes the timeout settings to improve sensor stability: - After sending a reset command to the chip, the timeout has been extended from 2.5 ms to 15 ms, aligning with the DPS310 specification. - The read timeout value of the MEAS_CFG register has been adjusted from 20ms to 30ms to match the specification. Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com> Fixes: 7b4ab4abcea4 ("iio: pressure: dps310: Reset chip after timeout") Link: https://lore.kernel.org/r/20230829180222.3431926-2-lakshmiy@us.ibm.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05iio: imu: bno055: Fix missing Kconfig dependenciesJonathan Cameron
This driver uses IIO triggered buffers so it needs to select them in Kconfig. on riscv-32bit: /opt/crosstool/gcc-13.2.0-nolibc/riscv32-linux/bin/riscv32-linux-ld: drivers/iio/imu/bno055/bno055.o: in function `.L367': bno055.c:(.text+0x2c96): undefined reference to `devm_iio_triggered_buffer_setup_ext' Reported-by: Randy Dunlap <rdunlap@infradead.org> Closes: https://lore.kernel.org/linux-next/40566b4b-3950-81fe-ff14-871d8c447627@infradead.org/ Fixes: 4aefe1c2bd0c ("iio: imu: add Bosch Sensortec BNO055 core driver") Cc: Andrea Merello <andrea.merello@iit.it> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20230903113052.846298-1-jic23@kernel.org Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05iio: adc: imx8qxp: Fix address for command buffer registersPhilipp Rossak
The ADC Command Buffer Register high and low are currently pointing to the wrong address and makes it impossible to perform correct ADC measurements over all channels. According to the datasheet of the imx8qxp the ADC_CMDL register starts at address 0x100 and the ADC_CMDH register starts at address 0x104. This bug seems to be in the kernel since the introduction of this driver. This can be observed by checking all raw voltages of the adc and they are all nearly identical: cat /sys/bus/iio/devices/iio\:device0/in_voltage*_raw 3498 3494 3491 3491 3489 3490 3490 3490 Fixes: 1e23dcaa1a9fa ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC") Signed-off-by: Philipp Rossak <embed3d@gmail.com> Acked-by: Haibo Chen <haibo.chen@nxp.com> Link: https://lore.kernel.org/r/20230904220204.23841-1-embed3d@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()Tzung-Bi Shih
cros_ec_sensors_push_data() reads `indio_dev->active_scan_mask` and calls iio_push_to_buffers_with_timestamp() without making sure the `indio_dev` stays in buffer mode. There is a race if `indio_dev` exits buffer mode right before cros_ec_sensors_push_data() accesses them. An use-after-free on `indio_dev->active_scan_mask` was observed. The call trace: [...] _find_next_bit cros_ec_sensors_push_data cros_ec_sensorhub_event blocking_notifier_call_chain cros_ec_irq_thread It was caused by a race condition: one thread just freed `active_scan_mask` at [1]; while another thread tried to access the memory at [2]. Fix it by calling iio_device_claim_buffer_mode() to ensure the `indio_dev` can't exit buffer mode during cros_ec_sensors_push_data(). [1]: https://elixir.bootlin.com/linux/v6.5/source/drivers/iio/industrialio-buffer.c#L1189 [2]: https://elixir.bootlin.com/linux/v6.5/source/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c#L198 Cc: stable@vger.kernel.org Fixes: aa984f1ba4a4 ("iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO") Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org> Reviewed-by: Guenter Roeck <groeck@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20230829030622.1571852-1-tzungbi@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05iio: irsd200: fix -Warray-bounds bug in irsd200_trigger_handlerGONG, Ruiqi
When compiling with gcc 13 with -Warray-bounds enabled: In file included from drivers/iio/proximity/irsd200.c:15: In function ‘iio_push_to_buffers_with_timestamp’, inlined from ‘irsd200_trigger_handler’ at drivers/iio/proximity/irsd200.c:770:2: ./include/linux/iio/buffer.h:42:46: error: array subscript ‘int64_t {aka long long int}[0]’ is partly outside array bounds of ‘s16[1]’ {aka ‘short int[1]’} [-Werror=array-bounds=] 42 | ((int64_t *)data)[ts_offset] = timestamp; | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~ drivers/iio/proximity/irsd200.c: In function ‘irsd200_trigger_handler’: drivers/iio/proximity/irsd200.c:763:13: note: object ‘buf’ of size 2 763 | s16 buf = 0; | ^~~ The problem seems to be that irsd200_trigger_handler() is taking a s16 variable as an int64_t buffer. As Jonathan suggested [1], fix it by extending the buffer to a two-element array of s64. Link: https://github.com/KSPP/linux/issues/331 Link: https://lore.kernel.org/lkml/20230809181329.46c00a5d@jic23-huawei/ [1] Fixes: 3db3562bc66e ("iio: Add driver for Murata IRS-D200") Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com> Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Waqar Hameed <waqar.hameed@axis.com> Tested-by: Waqar Hameed <waqar.hameed@axis.com> Reviewed-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20230810035910.1334706-1-gongruiqi@huaweicloud.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2023-10-05RDMA/core: Require admin capabilities to set system parametersLeon Romanovsky
Like any other set command, require admin permissions to do it. Cc: stable@vger.kernel.org Fixes: 2b34c5580226 ("RDMA/core: Add command to set ib_core device net namspace sharing mode") Link: https://lore.kernel.org/r/75d329fdd7381b52cbdf87910bef16c9965abb1f.1696443438.git.leon@kernel.org Reviewed-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
2023-10-05nvme-rdma: do not try to stop unallocated queuesMaurizio Lombardi
Trying to stop a queue which hasn't been allocated will result in a warning due to calling mutex_lock() against an uninitialized mutex. DEBUG_LOCKS_WARN_ON(lock->magic != lock) WARNING: CPU: 4 PID: 104150 at kernel/locking/mutex.c:579 Call trace: RIP: 0010:__mutex_lock+0x1173/0x14a0 nvme_rdma_stop_queue+0x1b/0xa0 [nvme_rdma] nvme_rdma_teardown_io_queues.part.0+0xb0/0x1d0 [nvme_rdma] nvme_rdma_delete_ctrl+0x50/0x100 [nvme_rdma] nvme_do_delete_ctrl+0x149/0x158 [nvme_core] Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Tested-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Keith Busch <kbusch@kernel.org>
2023-10-05net: stmmac: remove unneeded stmmac_poll_controllerRemi Pommarel
Using netconsole netpoll_poll_dev could be called from interrupt context, thus using disable_irq() would cause the following kernel warning with CONFIG_DEBUG_ATOMIC_SLEEP enabled: BUG: sleeping function called from invalid context at kernel/irq/manage.c:137 in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 10, name: ksoftirqd/0 CPU: 0 PID: 10 Comm: ksoftirqd/0 Tainted: G W 5.15.42-00075-g816b502b2298-dirty #117 Hardware name: aml (r1) (DT) Call trace: dump_backtrace+0x0/0x270 show_stack+0x14/0x20 dump_stack_lvl+0x8c/0xac dump_stack+0x18/0x30 ___might_sleep+0x150/0x194 __might_sleep+0x64/0xbc synchronize_irq+0x8c/0x150 disable_irq+0x2c/0x40 stmmac_poll_controller+0x140/0x1a0 netpoll_poll_dev+0x6c/0x220 netpoll_send_skb+0x308/0x390 netpoll_send_udp+0x418/0x760 write_msg+0x118/0x140 [netconsole] console_unlock+0x404/0x500 vprintk_emit+0x118/0x250 dev_vprintk_emit+0x19c/0x1cc dev_printk_emit+0x90/0xa8 __dev_printk+0x78/0x9c _dev_warn+0xa4/0xbc ath10k_warn+0xe8/0xf0 [ath10k_core] ath10k_htt_txrx_compl_task+0x790/0x7fc [ath10k_core] ath10k_pci_napi_poll+0x98/0x1f4 [ath10k_pci] __napi_poll+0x58/0x1f4 net_rx_action+0x504/0x590 _stext+0x1b8/0x418 run_ksoftirqd+0x74/0xa4 smpboot_thread_fn+0x210/0x3c0 kthread+0x1fc/0x210 ret_from_fork+0x10/0x20 Since [0] .ndo_poll_controller is only needed if driver doesn't or partially use NAPI. Because stmmac does so, stmmac_poll_controller can be removed fixing the above warning. [0] commit ac3d9dd034e5 ("netpoll: make ndo_poll_controller() optional") Cc: <stable@vger.kernel.org> # 5.15.x Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers") Signed-off-by: Remi Pommarel <repk@triplefau.lt> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/1c156a6d8c9170bd6a17825f2277115525b4d50f.1696429960.git.repk@triplefau.lt Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-10-05net: lan743x: also select PHYLIBRandy Dunlap
Since FIXED_PHY depends on PHYLIB, PHYLIB needs to be set to avoid a kconfig warning: WARNING: unmet direct dependencies detected for FIXED_PHY Depends on [n]: NETDEVICES [=y] && PHYLIB [=n] Selected by [y]: - LAN743X [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && PCI [=y] && PTP_1588_CLOCK_OPTIONAL [=y] Fixes: 73c4d1b307ae ("net: lan743x: select FIXED_PHY") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Closes: lore.kernel.org/r/202309261802.JPbRHwti-lkp@intel.com Cc: Bryan Whitehead <bryan.whitehead@microchip.com> Cc: UNGLinuxDriver@microchip.com Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Simon Horman <horms@kernel.org> # build-tested Link: https://lore.kernel.org/r/20231002193544.14529-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit (git 2.34.1) at 2025-09-15 12:24:09 +0000