| Age | Commit message (Collapse) | Author |
|---|
|
Force a fixed MDI-X mode when auto-negotiation is disabled to prevent
link instability.
When forcing the link speed and duplex on a LAN9500 PHY (e.g., with
`ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto
mode, the PHY fails to establish a stable link. This occurs because the
PHY's Auto-MDIX algorithm is not designed to operate when
auto-negotiation is disabled. In this state, the PHY continuously
toggles the TX/RX signal pairs, which prevents the link partner from
synchronizing.
This patch resolves the issue by detecting when auto-negotiation is
disabled. If the MDI-X control mode is set to 'auto', the driver now
forces a specific, stable mode (ETH_TP_MDI) to prevent the pair
toggling. This choice of a fixed MDI mode mirrors the behavior the
hardware would exhibit if the AUTOMDIX_EN strap were configured for a
fixed MDI connection.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Override the hardware strap configuration for MDI-X mode to ensure a
predictable initial state for the driver. The initial mode of the LAN87xx
PHY is determined by the AUTOMDIX_EN strap pin, but the driver has no
documented way to read its latched status.
This unpredictability means the driver cannot know if the PHY has
initialized with Auto-MDIX enabled or disabled, preventing it from
providing a reliable interface to the user.
This patch introduces a `config_init` hook that forces the PHY into a
known state by explicitly enabling Auto-MDIX.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct the Auto-MDIX configuration to ensure userspace settings are
respected when the feature is disabled by the AUTOMDIX_EN hardware strap.
The LAN9500 PHY allows its default MDI-X mode to be configured via a
hardware strap. If this strap sets the default to "MDI-X off", the
driver was previously unable to enable Auto-MDIX from userspace.
When handling the ETH_TP_MDI_AUTO case, the driver would set the
SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required
SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY
falls back to its hardware strap default, ignoring the software request.
This patch corrects the behavior by also setting the override bit when
enabling Auto-MDIX. This ensures that the userspace configuration takes
precedence over the hardware strap, allowing Auto-MDIX to be enabled
correctly in all scenarios.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the Synopsys Controller IP XGMAC-10G Ethernet MAC Databook
v3.30a (section 2.7.2), when the INTM bit in the DMA_Mode register is set
to 2, the sbd_perch_tx_intr_o[] and sbd_perch_rx_intr_o[] signals operate
in level-triggered mode. However, in this configuration, the DMA does not
assert the XGMAC_NIS status bit for Rx or Tx interrupt events.
This creates a functional regression where the condition
if (likely(intr_status & XGMAC_NIS)) in dwxgmac2_dma_interrupt() will
never evaluate to true, preventing proper interrupt handling for
level-triggered mode. The hardware specification explicitly states that
"The DMA does not assert the NIS status bit for the Rx or Tx interrupt
events" (Synopsys DWC_XGMAC2 Databook v3.30a, sec. 2.7.2).
The fix ensures correct handling of both edge and level-triggered
interrupts while maintaining backward compatibility with existing
configurations. It has been tested on the hardware device (not publicly
available), and it can properly trigger the RX and TX interrupt handling
in both the INTM=0 and INTM=2 configurations.
Fixes: d6ddfacd95c7 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Tested-by: EricChan <chenchuangyu@xiaomi.com>
Signed-off-by: EricChan <chenchuangyu@xiaomi.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250703020449.105730-1-chenchuangyu@xiaomi.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"Two fixes for v6.16-rc6
The first patch fixes an embarrassing bug in the pwm core. I really
wonder this wasn't found earlier since it's introduction in v6.11-rc1
as it greatly disturbs driving a PWM via sysfs.
The second and last patch fixes a clock balance issue in an error path
of the Mediatek PWM driver"
* tag 'pwm/for-6.16-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: mediatek: Ensure to disable clocks in error path
pwm: Fix invalid state detection
|
|
If an error occurs after a successful airoha_hw_init() call,
airoha_ppe_deinit() needs to be called as already done in the remove
function.
Fixes: 00a7678310fe ("net: airoha: Introduce flowtable offload support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/1c940851b4fa3c3ed2a142910c821493a136f121.1746715755.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add check for the return value of rcar_gen4_ptp_alloc()
to prevent potential null pointer dereference.
Fixes: b0d3969d2b4d ("net: ethernet: rtsn: Add support for Renesas Ethernet-TSN")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20250703100109.2541018-1-haoxiang_li2024@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On some models supported by ideapad-laptop, the HW/FW can remember the
state of keyboard backlight among boots. However, it is always turned
off while shutting down, as a side effect of the LED class device
unregistering sequence.
This is inconvenient for users who always prefer turning on the
keyboard backlight. Thus, set LED_RETAIN_AT_SHUTDOWN on the LED class
device so that the state of keyboard backlight gets remembered, which
also aligns with the behavior of manufacturer utilities on Windows.
Fixes: 503325f84bc0 ("platform/x86: ideapad-laptop: add keyboard backlight control support")
Cc: stable@vger.kernel.org
Signed-off-by: Rong Zhang <i@rong.moe>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250707163808.155876-3-i@rong.moe
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
On devices supported by ideapad-laptop, the HW/FW can remember the
FnLock state among boots. However, since the introduction of the FnLock
LED class device, it is turned off while shutting down, as a side effect
of the LED class device unregistering sequence.
Many users always turn on FnLock because they use function keys much
more frequently than multimedia keys. The behavior change is
inconvenient for them. Thus, set LED_RETAIN_AT_SHUTDOWN on the LED class
device so that the FnLock state gets remembered, which also aligns with
the behavior of manufacturer utilities on Windows.
Fixes: 07f48f668fac ("platform/x86: ideapad-laptop: add FnLock LED class device")
Cc: stable@vger.kernel.org
Signed-off-by: Rong Zhang <i@rong.moe>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250707163808.155876-2-i@rong.moe
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
There looks to be an issue in our compression handling when the BO pages
are very fragmented, where we choose to skip the identity map and
instead fall back to emitting the PTEs by hand when migrating memory,
such that we can hopefully do more work per blit operation. However in
such a case we need to ensure the src PTEs are correctly tagged with a
compression enabled PAT index on dgpu xe2+, otherwise the copy will
simply treat the src memory as uncompressed, leading to corruption if
the memory was compressed by the user.
To fix this pass along use_comp_pat into emit_pte() on the src side, to
indicate that compression should be considered.
v2 (Jonathan): tweak the commit message
Fixes: 523f191cc0c7 ("drm/xe/xe_migrate: Handle migration logic for xe2+ dgfx")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Akshata Jahagirdar <akshata.jahagirdar@intel.com>
Cc: <stable@vger.kernel.org> # v6.12+
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Link: https://lore.kernel.org/r/20250701103949.83116-2-matthew.auld@intel.com
(cherry picked from commit f7a2fd776e57bd6468644bdecd91ab3aba57ba58)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
This reverts commit fe0154cf8222d9e38c60ccc124adb2f9b5272371.
Seeing some unexplained random failures during LRC context switches with
indirect ring state enabled. The failures were always there, but the
repro rate increased with the addition of WA BB as a separate BO.
Commit 3a1edef8f4b5 ("drm/xe: Make WA BB part of LRC BO") helped to
reduce the issues in the context switches, but didn't eliminate them
completely.
Indirect ring state is not required for any current features, so disable
for now until failures can be root caused.
Cc: stable@vger.kernel.org
Fixes: fe0154cf8222 ("drm/xe/xe2: Enable Indirect Ring State support for Xe2")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250702035846.3178344-1-matthew.brost@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 03d85ab36bcbcbe9dc962fccd3f8e54d7bb93b35)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
CIRC_SPACE does not work unless the size argument is a power of 2,
allocate PF queue size on power of 2 boundary.
Cc: stable@vger.kernel.org
Fixes: 3338e4f90c14 ("drm/xe: Use topology to determine page fault queue size")
Fixes: 29582e0ea75c ("drm/xe: Add page queue multiplier")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://lore.kernel.org/r/20250702213511.3226167-1-matthew.brost@intel.com
(cherry picked from commit 491b9783126303755717c0cbde0b08ee59b6abab)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Our LMEM buffer objects are not cleared by default on alloc
and during VF provisioning we only setup LMTT PTEs for the
actually provisioned LMEM range. But beyond that valid range
we might leave some stale data that could either point to some
other VFs allocations or even to the PF pages.
Explicitly clear all new LMTT page to avoid the risk that a
malicious VF would try to exploit that gap.
While around add asserts to catch any undesired PTE overwrites
and low-level debug traces to track LMTT PT life-cycle.
Fixes: b1d204058218 ("drm/xe/pf: Introduce Local Memory Translation Table")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Lukasz Laguna <lukasz.laguna@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://lore.kernel.org/r/20250701220052.1612-1-michal.wajdeczko@intel.com
(cherry picked from commit 3fae6918a3e27cce20ded2551f863fb05d4bef8d)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Initialize u64 stats as it uses seq counter on 32bit machines
as suggested by lockdep below.
[ 1.830953][ T1] INFO: trying to register non-static key.
[ 1.830993][ T1] The code is fine but needs lockdep annotation, or maybe
[ 1.831027][ T1] you didn't initialize this object before use?
[ 1.831057][ T1] turning off the locking correctness validator.
[ 1.831090][ T1] CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.16.0-rc2-v7l+ #1 PREEMPT
[ 1.831097][ T1] Tainted: [W]=WARN
[ 1.831099][ T1] Hardware name: BCM2711
[ 1.831101][ T1] Call trace:
[ 1.831104][ T1] unwind_backtrace from show_stack+0x18/0x1c
[ 1.831120][ T1] show_stack from dump_stack_lvl+0x8c/0xcc
[ 1.831129][ T1] dump_stack_lvl from register_lock_class+0x9e8/0x9fc
[ 1.831141][ T1] register_lock_class from __lock_acquire+0x420/0x22c0
[ 1.831154][ T1] __lock_acquire from lock_acquire+0x130/0x3f8
[ 1.831166][ T1] lock_acquire from bcmgenet_get_stats64+0x4a4/0x4c8
[ 1.831176][ T1] bcmgenet_get_stats64 from dev_get_stats+0x4c/0x408
[ 1.831184][ T1] dev_get_stats from rtnl_fill_stats+0x38/0x120
[ 1.831193][ T1] rtnl_fill_stats from rtnl_fill_ifinfo+0x7f8/0x1890
[ 1.831203][ T1] rtnl_fill_ifinfo from rtmsg_ifinfo_build_skb+0xd0/0x138
[ 1.831214][ T1] rtmsg_ifinfo_build_skb from rtmsg_ifinfo+0x48/0x8c
[ 1.831225][ T1] rtmsg_ifinfo from register_netdevice+0x8c0/0x95c
[ 1.831237][ T1] register_netdevice from register_netdev+0x28/0x40
[ 1.831247][ T1] register_netdev from bcmgenet_probe+0x690/0x6bc
[ 1.831255][ T1] bcmgenet_probe from platform_probe+0x64/0xbc
[ 1.831263][ T1] platform_probe from really_probe+0xd0/0x2d4
[ 1.831269][ T1] really_probe from __driver_probe_device+0x90/0x1a4
[ 1.831273][ T1] __driver_probe_device from driver_probe_device+0x38/0x11c
[ 1.831278][ T1] driver_probe_device from __driver_attach+0x9c/0x18c
[ 1.831282][ T1] __driver_attach from bus_for_each_dev+0x84/0xd4
[ 1.831291][ T1] bus_for_each_dev from bus_add_driver+0xd4/0x1f4
[ 1.831303][ T1] bus_add_driver from driver_register+0x88/0x120
[ 1.831312][ T1] driver_register from do_one_initcall+0x78/0x360
[ 1.831320][ T1] do_one_initcall from kernel_init_freeable+0x2bc/0x314
[ 1.831331][ T1] kernel_init_freeable from kernel_init+0x1c/0x144
[ 1.831339][ T1] kernel_init from ret_from_fork+0x14/0x20
[ 1.831344][ T1] Exception stack(0xf082dfb0 to 0xf082dff8)
[ 1.831349][ T1] dfa0: 00000000 00000000 00000000 00000000
[ 1.831353][ T1] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.831356][ T1] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
Fixes: 59aa6e3072aa ("net: bcmgenet: switch to use 64bit statistics")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250702092417.46486-1-ryotkkr98@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Drop preprocessor macros in zboot.lds which is not preprocessed
- Fix zboot .data section size and raw size when SBAT is enabled
* tag 'efi-fixes-for-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: Fix .data section size calculations when .sbat is present
efi: Drop preprocessor directives from zboot.lds
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU speculation fixes from Borislav Petkov:
"Add the mitigation logic for Transient Scheduler Attacks (TSA)
TSA are new aspeculative side channel attacks related to the execution
timing of instructions under specific microarchitectural conditions.
In some cases, an attacker may be able to use this timing information
to infer data from other contexts, resulting in information leakage.
Add the usual controls of the mitigation and integrate it into the
existing speculation bugs infrastructure in the kernel"
* tag 'tsa_x86_bugs_for_6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/process: Move the buffer clearing before MONITOR
x86/microcode/AMD: Add TSA microcode SHAs
KVM: SVM: Advertise TSA CPUID bits to guests
x86/bugs: Add a Transient Scheduler Attacks mitigation
x86/bugs: Rename MDS machinery to something more generic
|
|
The previous commit unintentionally removed the code responsible for
enabling WoL via MMD3 register 0x8012 BIT5. As a result, Wake-on-LAN
(WoL) support for the QCA808X PHY is no longer functional.
The WoL (Wake-on-LAN) feature for the QCA808X PHY is enabled via MMD3
register 0x8012, BIT5. This implementation is aligned with the approach
used in at8031_set_wol().
Fixes: e58f30246c35 ("net: phy: at803x: fix the wol setting functions")
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250704-qcom_phy_wol_support-v1-2-053342b1538d@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the WoL (Wake-on-LAN) functionality to a shared library to enable
its reuse by the QCA808X PHY driver, incorporating support for WoL
functionality similar to the implementation in at8031_set_wol().
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://patch.msgid.link/20250704-qcom_phy_wol_support-v1-1-053342b1538d@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a use-after-free issue in nbd:
block nbd6: Receive control failed (result -104)
block nbd6: shutting down sockets
==================================================================
BUG: KASAN: slab-use-after-free in recv_work+0x694/0xa80 drivers/block/nbd.c:1022
Write of size 4 at addr ffff8880295de478 by task kworker/u33:0/67
CPU: 2 UID: 0 PID: 67 Comm: kworker/u33:0 Not tainted 6.15.0-rc5-syzkaller-00123-g2c89c1b655c0 #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Workqueue: nbd6-recv recv_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xc3/0x670 mm/kasan/report.c:521
kasan_report+0xe0/0x110 mm/kasan/report.c:634
check_region_inline mm/kasan/generic.c:183 [inline]
kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189
instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
atomic_dec include/linux/atomic/atomic-instrumented.h:592 [inline]
recv_work+0x694/0xa80 drivers/block/nbd.c:1022
process_one_work+0x9cc/0x1b70 kernel/workqueue.c:3238
process_scheduled_works kernel/workqueue.c:3319 [inline]
worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400
kthread+0x3c2/0x780 kernel/kthread.c:464
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
nbd_genl_connect() does not properly stop the device on certain
error paths after nbd_start_device() has been called. This causes
the error path to put nbd->config while recv_work continue to use
the config after putting it, leading to use-after-free in recv_work.
This patch moves nbd_start_device() after the backend file creation.
Reported-by: syzbot+48240bab47e705c53126@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/68227a04.050a0220.f2294.00b5.GAE@google.com/T/
Fixes: 6497ef8df568 ("nbd: provide a way for userspace processes to identify device backends")
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250612132405.364904-1-zhengqixing@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
same channel
Due to the lack of NoA(Notice of Absence) mechanism in SoftAP mode, it is
inappropriate to allow concurrent SoftAP and STA to operate on the
different channels.
This patch restricts the concurrent SoftAP and STA to be setup on the same
channel only.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250625073720.1385210-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
devm_kasprintf() returns NULL on error. Currently, mt7925_thermal_init()
does not check for this case, which results in a NULL pointer
dereference.
Add NULL check after devm_kasprintf() to prevent this issue.
Fixes: 396e41a74a88 ("wifi: mt76: mt7925: support temperature sensor")
Signed-off-by: Henry Martin <bsdhenryma@tencent.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250625124901.1839832-1-bsdhenryma@tencent.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When running in AP mode and deauthenticating a client that's in powersave
mode, the disassoc/deauth packet can get stuck in a tx queue along with
other buffered frames. This can fill up hardware queues with frames
that are only released after the WTBL slot is reused for another client.
Fix this by moving deauth packets to the ALTX queue.
Reported-by: Chad Monroe <chad.monroe@adtran.com>
Link: https://patch.msgid.link/20250707154702.1726-2-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Link: https://patch.msgid.link/20250707154702.1726-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The decap offload configuration should only be applied after the STA has
been successfully initialized. Attempting to configure it earlier can lead
to corruption of the MAC configuration in the chip's hardware state.
Add an early check for `msta->deflink.wcid.sta` to ensure the station peer
is properly initialized before proceeding with decapsulation offload
configuration.
Cc: stable@vger.kernel.org
Fixes: 24299fc869f7 ("mt76: mt7921: enable rx header traslation offload")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Link: https://patch.msgid.link/f23a72ba7a3c1ad38ba9e13bb54ef21d6ef44ffb.1748149855.git.deren.wu@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
mt7925_sta_set_decap_offload()
Add a NULL check for msta->vif before accessing its members to prevent
a kernel panic in AP mode deployment. This also fix the issue reported
in [1].
The crash occurs when this function is triggered before the station is
fully initialized. The call trace shows a page fault at
mt7925_sta_set_decap_offload() due to accessing resources when msta->vif
is NULL.
Fix this by adding an early return if msta->vif is NULL and also check
wcid.sta is ready. This ensures we only proceed with decap offload
configuration when the station's state is properly initialized.
[14739.655703] Unable to handle kernel paging request at virtual address ffffffffffffffa0
[14739.811820] CPU: 0 UID: 0 PID: 895854 Comm: hostapd Tainted: G
[14739.821394] Tainted: [C]=CRAP, [O]=OOT_MODULE
[14739.825746] Hardware name: Raspberry Pi 4 Model B Rev 1.1 (DT)
[14739.831577] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[14739.838538] pc : mt7925_sta_set_decap_offload+0xc0/0x1b8 [mt7925_common]
[14739.845271] lr : mt7925_sta_set_decap_offload+0x58/0x1b8 [mt7925_common]
[14739.851985] sp : ffffffc085efb500
[14739.855295] x29: ffffffc085efb500 x28: 0000000000000000 x27: ffffff807803a158
[14739.862436] x26: ffffff8041ececb8 x25: 0000000000000001 x24: 0000000000000001
[14739.869577] x23: 0000000000000001 x22: 0000000000000008 x21: ffffff8041ecea88
[14739.876715] x20: ffffff8041c19ca0 x19: ffffff8078031fe0 x18: 0000000000000000
[14739.883853] x17: 0000000000000000 x16: ffffffe2aeac1110 x15: 000000559da48080
[14739.890991] x14: 0000000000000001 x13: 0000000000000000 x12: 0000000000000000
[14739.898130] x11: 0a10020001008e88 x10: 0000000000001a50 x9 : ffffffe26457bfa0
[14739.905269] x8 : ffffff8042013bb0 x7 : ffffff807fb6cbf8 x6 : dead000000000100
[14739.912407] x5 : dead000000000122 x4 : ffffff80780326c8 x3 : 0000000000000000
[14739.919546] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8041ececb8
[14739.926686] Call trace:
[14739.929130] mt7925_sta_set_decap_offload+0xc0/0x1b8 [mt7925_common]
[14739.935505] ieee80211_check_fast_rx+0x19c/0x510 [mac80211]
[14739.941344] _sta_info_move_state+0xe4/0x510 [mac80211]
[14739.946860] sta_info_move_state+0x1c/0x30 [mac80211]
[14739.952116] sta_apply_auth_flags.constprop.0+0x90/0x1b0 [mac80211]
[14739.958708] sta_apply_parameters+0x234/0x5e0 [mac80211]
[14739.964332] ieee80211_add_station+0xdc/0x190 [mac80211]
[14739.969950] nl80211_new_station+0x46c/0x670 [cfg80211]
[14739.975516] genl_family_rcv_msg_doit+0xdc/0x150
[14739.980158] genl_rcv_msg+0x218/0x298
[14739.983830] netlink_rcv_skb+0x64/0x138
[14739.987670] genl_rcv+0x40/0x60
[14739.990816] netlink_unicast+0x314/0x380
[14739.994742] netlink_sendmsg+0x198/0x3f0
[14739.998664] __sock_sendmsg+0x64/0xc0
[14740.002324] ____sys_sendmsg+0x260/0x298
[14740.006242] ___sys_sendmsg+0xb4/0x110
Cc: stable@vger.kernel.org
Link: https://github.com/morrownr/USB-WiFi/issues/603 [1]
Fixes: b859ad65309a ("wifi: mt76: mt7925: add link handling in mt7925_sta_set_decap_offload")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Link: https://patch.msgid.link/35aedbffa050e98939264300407a52ba4e236d52.1748149855.git.deren.wu@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The IEs should be processed and filled into the command tlv separately
according to each band.
Cc: stable@vger.kernel.org
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250616063649.1100503-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Update the destination index to use 'n_ssids', which is incremented only
when a valid SSID is present. Previously, both mt76_connac_mcu_hw_scan()
and mt7925_mcu_hw_scan() used the loop index 'i' for the destination
array, potentially leaving gaps if any source SSIDs had zero length.
Cc: stable@vger.kernel.org
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250612062046.160598-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
MT_INT_TX_DONE_MCU_WM may cause tx interrupt to be mishandled
during a reset failure, leading to the reset process failing.
By using MT_INT_TX_DONE_MCU instead of MT_INT_TX_DONE_MCU_WM,
the handling of tx interrupt is improved.
Cc: stable@vger.kernel.org
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250612060931.135635-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Since mt7996_mcu_add_rate_ctrl() and mt7996_mcu_set_fixed_field() can't
run in atomic context, move RCU critical section in
mt7996_mcu_add_rate_ctrl() and mt7996_mcu_set_fixed_field(). This patch
fixes a 'sleep while atomic' issue in mt7996_mac_sta_rc_work().
Fixes: 0762bdd30279 ("wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Link: https://patch.msgid.link/20250605-mt7996-sleep-while-atomic-v1-5-d46d15f9203c@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Since mt76_mcu_skb_send_msg() routine can't be executed in atomic context,
move RCU section in mt7996_mcu_add_rate_ctrl() and execute
mt76_mcu_skb_send_msg() in non-atomic context. This is a preliminary
patch to fix a 'sleep while atomic' issue in mt7996_mac_sta_rc_work().
Fixes: 0762bdd30279 ("wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250605-mt7996-sleep-while-atomic-v1-4-d46d15f9203c@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Since mt7996_mcu_set_fixed_field() can't be executed in a RCU critical
section, move RCU section in mt7996_mcu_add_rate_ctrl_fixed() and run
mt7996_mcu_set_fixed_field() in non-atomic context. This is a
preliminary patch to fix a 'sleep while atomic' issue in
mt7996_mac_sta_rc_work().
Fixes: 0762bdd30279 ("wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250605-mt7996-sleep-while-atomic-v1-3-d46d15f9203c@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Since mt76_mcu_skb_send_msg() routine can't be executed in atomic context,
move RCU section in mt7996_mcu_set_fixed_field() and execute
mt76_mcu_skb_send_msg() in non-atomic context. This is a preliminary
patch to fix a 'sleep while atomic' issue in mt7996_mac_sta_rc_work().
Fixes: 0762bdd30279 ("wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250605-mt7996-sleep-while-atomic-v1-2-d46d15f9203c@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Rely on GFP_ATOMIC flag in __mt76_connac_mcu_alloc_sta_req since it can
run in atomic context. This is a preliminary patch to fix a 'sleep while
atomic' issue in mt7996_mac_sta_rc_work().
Fixes: 0762bdd30279 ("wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250605-mt7996-sleep-while-atomic-v1-1-d46d15f9203c@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
If any of the ACPI calls fail, memory allocated for the input buffer
would be leaked. Fix failure paths to free allocated memory.
Also add checks to ensure the allocations succeeded in the first place.
Reported-by: Danilo Krummrich <dakr@kernel.org>
Fixes: 176fdcbddfd2 ("drm/nouveau/gsp/r535: add support for booting GSP-RM")
Signed-off-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://lore.kernel.org/r/20250617040036.2932-1-bskeggs@nvidia.com
|
|
For setting the enable value, the input should be 0 or 1 only. Use
kstrtobool() in place of kstrtoint() in mlxbf_pmc_enable_store() to
accept only valid input.
Fixes: 423c3361855c ("platform/mellanox: mlxbf-pmc: Add support for BlueField-3")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/2ee618c59976bcf1379d5ddce2fc60ab5014b3a9.1751380187.git.shravankr@nvidia.com
[ij: split kstrbool() change to own commit.]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Before programming the event info, validate the event number received as input
by checking if it exists in the event_list. Also fix a typo in the comment for
mlxbf_pmc_get_event_name() to correctly mention that it returns the event name
when taking the event number as input, and not the other way round.
Fixes: 423c3361855c ("platform/mellanox: mlxbf-pmc: Add support for BlueField-3")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/2ee618c59976bcf1379d5ddce2fc60ab5014b3a9.1751380187.git.shravankr@nvidia.com
[ij: split kstrbool() change to own commit.]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Since the input string passed via the command line appends a newline char,
it needs to be removed before comparison with the event_list.
Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/4978c18e33313b48fa2ae7f3aa6dbcfce40877e4.1751380187.git.shravankr@nvidia.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Calling power_supply_get_property() inside
dell_wmi_ddv_battery_translate() can cause a deadlock since this
function is also being called from the power supply extension code,
in which case psy->extensions_sem is already being held.
Fix this by using the new power_supply_get_property_direct() function
to ignore any power supply extensions when retrieving the battery
serial number.
Tested on a Dell Inspiron 3505.
Reported-by: Hans de Goede <hansg@kernel.org>
Fixes: 058de163a376 ("platform/x86: dell-ddv: Implement the battery matching algorithm")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250627205124.250433-3-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Test that power supply extensions can access properties of their
power supply using power_supply_get_property_direct(). This both
ensures that the functionality works and serves as an example for
future driver developers.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250627205124.250433-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Power supply extensions might want to interact with the underlying
power supply to retrieve data like serial numbers, charging status
and more. However doing so causes psy->extensions_sem to be locked
twice, possibly causing a deadlock.
Provide special variants of power_supply_get/set_property() that
ignore any power supply extensions and thus do not touch the
associated psy->extensions_sem lock.
Suggested-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250627205124.250433-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add missing empty member to `awcc_dmi_table`.
Cc: stable@vger.kernel.org
Fixes: 6d7f1b1a5db6 ("platform/x86: alienware-wmi: Split DMI table")
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250707-dmi-fix-v1-1-6730835d824d@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
When unplugging the USB cable or disconnecting a gadget in usb peripheral mode with
echo "" > /sys/kernel/config/usb_gadget/<your_gadget>/UDC,
/sys/class/udc/musb-hdrc.0/state does not change from USB_STATE_CONFIGURED.
Testing on dwc2/3 shows they both update the state to USB_STATE_NOTATTACHED.
Add calls to usb_gadget_set_state in musb_g_disconnect and musb_gadget_stop
to fix both cases.
Fixes: 49401f4169c0 ("usb: gadget: introduce gadget state tracking")
Cc: stable@vger.kernel.org
Co-authored-by: Yehowshua Immanuel <yehowshua.immanuel@twosixtech.com>
Signed-off-by: Yehowshua Immanuel <yehowshua.immanuel@twosixtech.com>
Signed-off-by: Drew Hamilton <drew.hamilton@zetier.com>
Link: https://lore.kernel.org/r/20250701154126.8543-1-drew.hamilton@zetier.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fixes for v6.16-rc4
This includes following USB4/Thunderbolt fixes for v6.16-rc4:
- Fix wake on connect during runtime suspend
- Fix bit masking in tb_dp_port_set_hops().
Both have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.16-rc4' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix bit masking in tb_dp_port_set_hops()
thunderbolt: Fix wake on connect at runtime
|
|
The function is used as remove callback for a platform driver.
It was missed during the conversion from int to void
Fixes: 0edb555a65d1 ("platform: Make platform_driver::remove() return void")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/20250706092053.97724-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When operating in concurrent STA/AP mode with host MLME enabled,
the firmware incorrectly sends disassociation frames to the STA
interface when clients disconnect from the AP interface.
This causes kernel warnings as the STA interface processes
disconnect events that don't apply to it:
[ 1303.240540] WARNING: CPU: 0 PID: 513 at net/wireless/mlme.c:141 cfg80211_process_disassoc+0x78/0xec [cfg80211]
[ 1303.250861] Modules linked in: 8021q garp stp mrp llc rfcomm bnep btnxpuart nls_iso8859_1 nls_cp437 onboard_us
[ 1303.327651] CPU: 0 UID: 0 PID: 513 Comm: kworker/u9:2 Not tainted 6.16.0-rc1+ #3 PREEMPT
[ 1303.335937] Hardware name: Toradex Verdin AM62 WB on Verdin Development Board (DT)
[ 1303.343588] Workqueue: MWIFIEX_RX_WORK_QUEUE mwifiex_rx_work_queue [mwifiex]
[ 1303.350856] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 1303.357904] pc : cfg80211_process_disassoc+0x78/0xec [cfg80211]
[ 1303.364065] lr : cfg80211_process_disassoc+0x70/0xec [cfg80211]
[ 1303.370221] sp : ffff800083053be0
[ 1303.373590] x29: ffff800083053be0 x28: 0000000000000000 x27: 0000000000000000
[ 1303.380855] x26: 0000000000000000 x25: 00000000ffffffff x24: ffff000002c5b8ae
[ 1303.388120] x23: ffff000002c5b884 x22: 0000000000000001 x21: 0000000000000008
[ 1303.395382] x20: ffff000002c5b8ae x19: ffff0000064dd408 x18: 0000000000000006
[ 1303.402646] x17: 3a36333a61623a30 x16: 32206d6f72662063 x15: ffff800080bfe048
[ 1303.409910] x14: ffff000003625300 x13: 0000000000000001 x12: 0000000000000000
[ 1303.417173] x11: 0000000000000002 x10: ffff000003958600 x9 : ffff000003625300
[ 1303.424434] x8 : ffff00003fd9ef40 x7 : ffff0000039fc280 x6 : 0000000000000002
[ 1303.431695] x5 : ffff0000038976d4 x4 : 0000000000000000 x3 : 0000000000003186
[ 1303.438956] x2 : 000000004836ba20 x1 : 0000000000006986 x0 : 00000000d00479de
[ 1303.446221] Call trace:
[ 1303.448722] cfg80211_process_disassoc+0x78/0xec [cfg80211] (P)
[ 1303.454894] cfg80211_rx_mlme_mgmt+0x64/0xf8 [cfg80211]
[ 1303.460362] mwifiex_process_mgmt_packet+0x1ec/0x460 [mwifiex]
[ 1303.466380] mwifiex_process_sta_rx_packet+0x1bc/0x2a0 [mwifiex]
[ 1303.472573] mwifiex_handle_rx_packet+0xb4/0x13c [mwifiex]
[ 1303.478243] mwifiex_rx_work_queue+0x158/0x198 [mwifiex]
[ 1303.483734] process_one_work+0x14c/0x28c
[ 1303.487845] worker_thread+0x2cc/0x3d4
[ 1303.491680] kthread+0x12c/0x208
[ 1303.495014] ret_from_fork+0x10/0x20
Add validation in the STA receive path to verify that disassoc/deauth
frames originate from the connected AP. Frames that fail this check
are discarded early, preventing them from reaching the MLME layer and
triggering WARN_ON().
This filtering logic is similar with that used in the
ieee80211_rx_mgmt_disassoc() function in mac80211, which drops
disassoc frames that don't match the current BSSID
(!ether_addr_equal(mgmt->bssid, sdata->vif.cfg.ap_addr)), ensuring
only relevant frames are processed.
Tested on:
- 8997 with FW 16.68.1.p197
Fixes: 36995892c271 ("wifi: mwifiex: add host mlme for client mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Jeff Chen <jeff.chen_1@nxp.con>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20250701142643.658990-1-ivitro@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After enabling the clocks each error path must disable the clocks again.
One of them failed to do so. Unify the error paths to use goto to make it
harder for future changes to add a similar bug.
Fixes: 7ca59947b5fc ("pwm: mediatek: Prevent divide-by-zero in pwm_mediatek_config()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250704172728.626815-2-u.kleine-koenig@baylibre.com
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
|
|
Commit 9dd42d019e63 ("pwm: Allow pwm state transitions from an invalid
state") intended to allow some state transitions that were not allowed
before. The idea is sane and back then I also got the code comment
right, but the check for enabled is bogus. This resulted in state
transitions for enabled states to be allowed to have invalid duty/period
settings and thus it can happen that low-level drivers get requests for
invalid states🙄.
Invert the check to allow state transitions for disabled states only.
Fixes: 9dd42d019e63 ("pwm: Allow pwm state transitions from an invalid state")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250704172416.626433-2-u.kleine-koenig@baylibre.com
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
- Initialize sysfs attributes properly to avoid lockdep complaining
about an uninitialized lock class
* tag 'edac_urgent_for_v6.16_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC: Initialize EDAC features sysfs attributes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
- Have irq-msi-lib select CONFIG_GENERIC_MSI_IRQ explicitly as it uses
its facilities
* tag 'irq_urgent_for_v6.16_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-msi-lib: Select CONFIG_GENERIC_MSI_IRQ
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- Memory corruption fixes in hid-appletb-kbd driver (Qasim Ijaz)
- New device ID in hid-elecom driver (Leonard Dizon)
- Fixed several HID debugfs contants (Vicki Pfau)
* tag 'hid-for-linus-2025070502' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: appletb-kbd: fix slab use-after-free bug in appletb_kbd_probe
HID: Fix debug name for BTN_GEAR_DOWN, BTN_GEAR_UP, BTN_WHEEL
HID: elecom: add support for ELECOM HUGE 019B variant
HID: appletb-kbd: fix memory corruption of input_handler_list
|
