| Age | Commit message (Collapse) | Author |
|---|
|
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Fixes: 7acc9973e3c4 ("usb: phy: generic: add vbus support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220425171412.1188485-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614f3 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Way back in commit 4f25580fb84d ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands
It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.
The aforementioned commit tried to get that right for HS400ES, although
it's unclear whether this ever truly worked as committed into mainline,
as other changes/refactoring adjusted the sequence in conflicting ways:
08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode
switch")
53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode
for mmc")
In any case, today we do step 3 before step 2. Let's fix that, and also
apply the same logic to HS200/400, where this eMMC has problems too.
Resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:
[ 2.058881] mmc1: CQHCI version 5.10
[ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.209804] mmc1: mmc_select_hs400es failed, error -84
[ 2.215597] mmc1: error -84 whilst initialising MMC card
[ 2.417514] mmc1: mmc_select_hs400es failed, error -110
[ 2.423373] mmc1: error -110 whilst initialising MMC card
[ 2.605052] mmc1: mmc_select_hs400es failed, error -110
[ 2.617944] mmc1: error -110 whilst initialising MMC card
[ 2.835884] mmc1: mmc_select_hs400es failed, error -110
[ 2.841751] mmc1: error -110 whilst initialising MMC card
Ealier versions of this patch bumped to 200MHz/HS200 speeds too early,
which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for
the report Luca!) After a second look, it appears that aligns with
JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz)
rates first.
Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode switch")
Fixes: 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Fixes: 4f25580fb84d ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds the necessary PCI IDs for Intel Meteor Lake-P
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220425103518.44028-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We received a report[1] of kernel crashes when Cilium is used in XDP
mode with virtio_net after updating to newer kernels. After
investigating the reason it turned out that when using mergeable bufs
with an XDP program which adjusts xdp.data or xdp.data_meta page_to_buf()
calculates the build_skb address wrong because the offset can become less
than the headroom so it gets the address of the previous page (-X bytes
depending on how lower offset is):
page_to_skb: page addr ffff9eb2923e2000 buf ffff9eb2923e1ffc offset 252 headroom 256
This is a pr_err() I added in the beginning of page_to_skb which clearly
shows offset that is less than headroom by adding 4 bytes of metadata
via an xdp prog. The calculations done are:
receive_mergeable():
headroom = VIRTIO_XDP_HEADROOM; // VIRTIO_XDP_HEADROOM == 256 bytes
offset = xdp.data - page_address(xdp_page) -
vi->hdr_len - metasize;
page_to_skb():
p = page_address(page) + offset;
...
buf = p - headroom;
Now buf goes -4 bytes from the page's starting address as can be seen
above which is set as skb->head and skb->data by build_skb later. Depending
on what's done with the skb (when it's freed most often) we get all kinds
of corruptions and BUG_ON() triggers in mm[2]. We have to recalculate
the new headroom after the xdp program has run, similar to how offset
and len are recalculated. Headroom is directly related to
data_hard_start, data and data_meta, so we use them to get the new size.
The result is correct (similar pr_err() in page_to_skb, one case of
xdp_page and one case of virtnet buf):
a) Case with 4 bytes of metadata
[ 115.949641] page_to_skb: page addr ffff8b4dcfad2000 offset 252 headroom 252
[ 121.084105] page_to_skb: page addr ffff8b4dcf018000 offset 20732 headroom 252
b) Case of pushing data +32 bytes
[ 153.181401] page_to_skb: page addr ffff8b4dd0c4d000 offset 288 headroom 288
[ 158.480421] page_to_skb: page addr ffff8b4dd00b0000 offset 24864 headroom 288
c) Case of pushing data -33 bytes
[ 835.906830] page_to_skb: page addr ffff8b4dd3270000 offset 223 headroom 223
[ 840.839910] page_to_skb: page addr ffff8b4dcdd68000 offset 12511 headroom 223
Offset and headroom are equal because offset points to the start of
reserved bytes for the virtio_net header which are at buf start +
headroom, while data points at buf start + vnet hdr size + headroom so
when data or data_meta are adjusted by the xdp prog both the headroom size
and the offset change equally. We can use data_hard_start to compute the
new headroom after the xdp prog (linearized / page start case, the
virtnet buf case is similar just with bigger base offset):
xdp.data_hard_start = page_address + vnet_hdr
xdp.data = page_address + vnet_hdr + headroom
new headroom after xdp prog = xdp.data - xdp.data_hard_start - metasize
An example reproducer xdp prog[3] is below.
[1] https://github.com/cilium/cilium/issues/19453
[2] Two of the many traces:
[ 40.437400] BUG: Bad page state in process swapper/0 pfn:14940
[ 40.916726] BUG: Bad page state in process systemd-resolve pfn:053b7
[ 41.300891] kernel BUG at include/linux/mm.h:720!
[ 41.301801] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 41.302784] CPU: 1 PID: 1181 Comm: kubelet Kdump: loaded Tainted: G B W 5.18.0-rc1+ #37
[ 41.304458] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1.fc35 04/01/2014
[ 41.306018] RIP: 0010:page_frag_free+0x79/0xe0
[ 41.306836] Code: 00 00 75 ea 48 8b 07 a9 00 00 01 00 74 e0 48 8b 47 48 48 8d 50 ff a8 01 48 0f 45 fa eb d0 48 c7 c6 18 b8 30 a6 e8 d7 f8 fc ff <0f> 0b 48 8d 78 ff eb bc 48 8b 07 a9 00 00 01 00 74 3a 66 90 0f b6
[ 41.310235] RSP: 0018:ffffac05c2a6bc78 EFLAGS: 00010292
[ 41.311201] RAX: 000000000000003e RBX: 0000000000000000 RCX: 0000000000000000
[ 41.312502] RDX: 0000000000000001 RSI: ffffffffa6423004 RDI: 00000000ffffffff
[ 41.313794] RBP: ffff993c98823600 R08: 0000000000000000 R09: 00000000ffffdfff
[ 41.315089] R10: ffffac05c2a6ba68 R11: ffffffffa698ca28 R12: ffff993c98823600
[ 41.316398] R13: ffff993c86311ebc R14: 0000000000000000 R15: 000000000000005c
[ 41.317700] FS: 00007fe13fc56740(0000) GS:ffff993cdd900000(0000) knlGS:0000000000000000
[ 41.319150] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 41.320152] CR2: 000000c00008a000 CR3: 0000000014908000 CR4: 0000000000350ee0
[ 41.321387] Call Trace:
[ 41.321819] <TASK>
[ 41.322193] skb_release_data+0x13f/0x1c0
[ 41.322902] __kfree_skb+0x20/0x30
[ 41.343870] tcp_recvmsg_locked+0x671/0x880
[ 41.363764] tcp_recvmsg+0x5e/0x1c0
[ 41.384102] inet_recvmsg+0x42/0x100
[ 41.406783] ? sock_recvmsg+0x1d/0x70
[ 41.428201] sock_read_iter+0x84/0xd0
[ 41.445592] ? 0xffffffffa3000000
[ 41.462442] new_sync_read+0x148/0x160
[ 41.479314] ? 0xffffffffa3000000
[ 41.496937] vfs_read+0x138/0x190
[ 41.517198] ksys_read+0x87/0xc0
[ 41.535336] do_syscall_64+0x3b/0x90
[ 41.551637] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 41.568050] RIP: 0033:0x48765b
[ 41.583955] Code: e8 4a 35 fe ff eb 88 cc cc cc cc cc cc cc cc e8 fb 7a fe ff 48 8b 7c 24 10 48 8b 74 24 18 48 8b 54 24 20 48 8b 44 24 08 0f 05 <48> 3d 01 f0 ff ff 76 20 48 c7 44 24 28 ff ff ff ff 48 c7 44 24 30
[ 41.632818] RSP: 002b:000000c000a2f5b8 EFLAGS: 00000212 ORIG_RAX: 0000000000000000
[ 41.664588] RAX: ffffffffffffffda RBX: 000000c000062000 RCX: 000000000048765b
[ 41.681205] RDX: 0000000000005e54 RSI: 000000c000e66000 RDI: 0000000000000016
[ 41.697164] RBP: 000000c000a2f608 R08: 0000000000000001 R09: 00000000000001b4
[ 41.713034] R10: 00000000000000b6 R11: 0000000000000212 R12: 00000000000000e9
[ 41.728755] R13: 0000000000000001 R14: 000000c000a92000 R15: ffffffffffffffff
[ 41.744254] </TASK>
[ 41.758585] Modules linked in: br_netfilter bridge veth netconsole virtio_net
and
[ 33.524802] BUG: Bad page state in process systemd-network pfn:11e60
[ 33.528617] page ffffe05dc0147b00 ffffe05dc04e7a00 ffff8ae9851ec000 (1) len 82 offset 252 metasize 4 hroom 0 hdr_len 12 data ffff8ae9851ec10c data_meta ffff8ae9851ec108 data_end ffff8ae9851ec14e
[ 33.529764] page:000000003792b5ba refcount:0 mapcount:-512 mapping:0000000000000000 index:0x0 pfn:0x11e60
[ 33.532463] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
[ 33.532468] raw: 000fffffc0000000 0000000000000000 dead000000000122 0000000000000000
[ 33.532470] raw: 0000000000000000 0000000000000000 00000000fffffdff 0000000000000000
[ 33.532471] page dumped because: nonzero mapcount
[ 33.532472] Modules linked in: br_netfilter bridge veth netconsole virtio_net
[ 33.532479] CPU: 0 PID: 791 Comm: systemd-network Kdump: loaded Not tainted 5.18.0-rc1+ #37
[ 33.532482] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1.fc35 04/01/2014
[ 33.532484] Call Trace:
[ 33.532496] <TASK>
[ 33.532500] dump_stack_lvl+0x45/0x5a
[ 33.532506] bad_page.cold+0x63/0x94
[ 33.532510] free_pcp_prepare+0x290/0x420
[ 33.532515] free_unref_page+0x1b/0x100
[ 33.532518] skb_release_data+0x13f/0x1c0
[ 33.532524] kfree_skb_reason+0x3e/0xc0
[ 33.532527] ip6_mc_input+0x23c/0x2b0
[ 33.532531] ip6_sublist_rcv_finish+0x83/0x90
[ 33.532534] ip6_sublist_rcv+0x22b/0x2b0
[3] XDP program to reproduce(xdp_pass.c):
#include <linux/bpf.h>
#include <bpf/bpf_helpers.h>
SEC("xdp_pass")
int xdp_pkt_pass(struct xdp_md *ctx)
{
bpf_xdp_adjust_head(ctx, -(int)32);
return XDP_PASS;
}
char _license[] SEC("license") = "GPL";
compile: clang -O2 -g -Wall -target bpf -c xdp_pass.c -o xdp_pass.o
load on virtio_net: ip link set enp1s0 xdpdrv obj xdp_pass.o sec xdp_pass
CC: stable@vger.kernel.org
CC: Jason Wang <jasowang@redhat.com>
CC: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
CC: Daniel Borkmann <daniel@iogearbox.net>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: virtualization@lists.linux-foundation.org
Fixes: 8fb7da9e9907 ("virtio_net: get build_skb() buf by data ptr")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220425103703.3067292-1-razor@blackwall.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The other port_hidden functions rely on the port_read/port_write
functions to access the hidden control port. These functions apply the
offset for port_base_addr where applicable. Update port_hidden_wait to
use the port_wait_bit so that port_base_addr offsets are accounted for
when waiting for the busy bit to change.
Without the offset the port_hidden_wait function would timeout on
devices that have a non-zero port_base_addr (e.g. MV88E6141), however
devices that have a zero port_base_addr would operate correctly (e.g.
MV88E6390).
Fixes: 609070133aff ("net: dsa: mv88e6xxx: update code operating on hidden registers")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220425070454.348584-1-nathan@nathanrossi.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Return back the error value that we get from phy_read_mmd().
Fixes: c84786fa8f91 ("net: phy: marvell10g: read copper results from CSSR1")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/f47cb031aeae873bb008ba35001607304a171a20.1650868058.git.baruch@tkos.co.il
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'
However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.
Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.
As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com
Fixes: d03825fba459 ("net: bcmgenet: add skb_tx_timestamp call")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
plane_state->uapi.crtc is not what we want to be looking at.
If bigjoiner is used hw.crtc is what tells us what crtc the plane
is supposedly using.
Not an actual problem on current hardware as the only FBC capable
pipe (A) can't be a bigjoiner slave and thus uapi.crtc==hw.crtc
always here. But when we get more FBC instances this will become
actually important.
Fixes: 2e6c99f88679 ("drm/i915/fbc: Nuke lots of crap from intel_fbc_state_cache")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220413152852.7336-1-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
(cherry picked from commit 3e1faae3398789abe8d4797255bfe28d95d81308)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Fix typo in the _SEL_FETCH_PLANE_BASE_1_B register base address.
Fixes: a5523e2ff074a5 ("drm/i915: Add PSR2 selective fetch registers")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/5400
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v5.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421162221.2261895-1-imre.deak@intel.com
(cherry picked from commit af2cbc6ef967f61711a3c40fca5366ea0bc7fecc)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
It's noted that dcvs interrupts are not self-clearing, thus an interrupt
handler runs constantly, which leads to a severe regression in runtime.
To fix the problem an explicit write to clear interrupt register is
required, note that on OSM platforms the register may not be present.
Fixes: 275157b367f4 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
'size' may be used uninitialized in gsm_dlci_modem_output() if called with
an adaption that is neither 1 nor 2. The function is currently only called
by gsm_modem_upd_via_data() and only for adaption 2.
Properly handle every invalid case by returning -EINVAL to silence the
compiler warning and avoid future regressions.
Fixes: c19ffe00fed6 ("tty: n_gsm: fix invalid use of MSC in advanced option")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220425104726.7986-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clk fixes from Jernej Skrabec:
- Add missing sentinel
- check return value for platform_get_resource()
- mark rtc-32k as critical
* tag 'sunxi-clk-fixes-for-5.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()
clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical
clk: sunxi-ng: fix not NULL terminated coccicheck error
|
|
Since version 5.13, the standard syscon bindings have been added
to all clps711x DT nodes, so we can now use the more general
syscon_regmap_lookup_by_phandle function to get the syscon pointer.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Fixes: 7a6fca879f59 ("clk: sunxi: Add driver for A80 MMC config clocks/resets")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220421134308.2885094-1-yangyingliang@huawei.com
|
|
This code is really spurious.
It always returns an ERR_PTR, even when err is known to be 0 and calls
put_device() after a successful device_register() call.
It is likely that the return statement in the normal path is missing.
Add 'return rdev;' to fix it.
Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/ef2b9576350bba4c8e05e669e9535e9e2a415763.1650551719.git.christophe.jaillet@wanadoo.fr
|
|
Explicitly disable PEC when the client does not support it.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without a new code, at the second load of the driver
(or bind) the "flags" variable is not updated to avoid PEC usage. As a
consequence the further communication with the device is done with
the PEC enabled, which is wrong and may fail.
The implementation first disable the I2C_CLIENT_PEC flag, then the old
code enable it if needed.
Fixes: 4e5418f787ec ("hwmon: (pmbus_core) Check adapter PEC support")
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220420145059.431061-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This reverts 35a33ff3807d ("random: use memmove instead of memcpy for
remaining 32 bytes"), which was made on a totally bogus basis. The thing
it was worried about overlapping came from the stack, not from one of
its arguments, as Eric pointed out.
But the fact that this confusion even happened draws attention to the
fact that it's a bit non-obvious that the random_data parameter can
alias chacha_state, and in fact should do so when the caller can't rely
on the stack being cleared in a timely manner. So this commit documents
that.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
bridge
DSA, through dsa_port_bridge_leave(), first notifies the port of the
fact that it left a bridge, then, if that bridge was VLAN-aware, it
notifies the port of the change in VLAN awareness state, towards
VLAN-unaware mode.
So ocelot_port_vlan_filtering() can be called when ocelot_port->bridge
is NULL, and this makes ocelot_add_vlan_unaware_pvid() create a struct
ocelot_bridge_vlan with a vid of 0 and an "untagged" setting of true on
that port.
In a way this structure correctly reflects the reality, but by design,
VID 0 (OCELOT_STANDALONE_PVID) was not meant to be kept in the bridge
VLAN list of the driver, but managed separately.
Having OCELOT_STANDALONE_PVID in ocelot->vlans makes us trip up on
several sanity checks that did not expect to have this VID there.
For example, after we leave a VLAN-aware bridge and we re-join it, we
can no longer program egress-tagged VLANs to hardware:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 nomaster
# ip link set swp0 master br0
# bridge vlan add dev swp0 vid 100
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
But this configuration is in fact supported by the hardware, since we
could use OCELOT_PORT_TAG_NATIVE. According to its comment:
/* all VLANs except the native VLAN and VID 0 are egress-tagged */
yet when assessing the eligibility for this mode, we do not check for
VID 0 in ocelot_port_uses_native_vlan(), instead we just ensure that
ocelot_port_num_untagged_vlans() == 1. This is simply because VID 0
doesn't have a bridge VLAN structure.
The way I identify the problem is that ocelot_port_vlan_filtering(false)
only means to call ocelot_add_vlan_unaware_pvid() when we dynamically
turn off VLAN awareness for a bridge we are under, and the PVID changes
from the bridge PVID to a reserved PVID based on the bridge number.
Since OCELOT_STANDALONE_PVID is statically added to the VLAN table
during ocelot_vlan_init() and never removed afterwards, calling
ocelot_add_vlan_unaware_pvid() for it is not intended and does not serve
any purpose.
Fix the issue by avoiding the call to ocelot_add_vlan_unaware_pvid(vid=0)
when we're resetting VLAN awareness after leaving the bridge, to become
a standalone port.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both the felix DSA driver and ocelot switchdev driver declare
dev->features & NETIF_F_HW_VLAN_CTAG_FILTER under certain circumstances*,
so the 8021q module will add VID 0 to our RX filter when the port goes
up, to ensure 802.1p traffic is not dropped.
We treat VID 0 as a special value (OCELOT_STANDALONE_PVID) which
deliberately does not have a struct ocelot_bridge_vlan associated with
it. Instead, this gets programmed to the VLAN table in ocelot_vlan_init().
If we allow external calls to modify VID 0, we reach the following
situation:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 up # this adds VID 0 to ocelot->vlans with untagged=false
bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged # the bridge also adds VID 1
br0 1 PVID Egress Untagged
# bridge vlan add dev swp0 vid 100 untagged
Error: mscc_ocelot_switch_lib: Port with egress-tagged VLANs cannot have more than one egress-untagged (native) VLAN.
This configuration should have been accepted, because
ocelot_port_manage_port_tag() should select OCELOT_PORT_TAG_NATIVE.
Yet it isn't, because we have an entry in ocelot->vlans which says
VID 0 should be egress-tagged, something the hardware can't do.
Fix this by suppressing additions/deletions on VID 0 and managing this
VLAN exclusively using OCELOT_STANDALONE_PVID.
*DSA toggles it when the port becomes VLAN-aware by joining a VLAN-aware
bridge. Ocelot declares it unconditionally for some reason.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lan966x->ports[] array has lan966x->num_phys_ports elements. These
are assigned in lan966x_probe(). That means the > comparison should be
changed to >=.
The first off by one check is harmless but the second one could lead to
an out of bounds access and a crash.
Fixes: 5ccd66e01cbe ("net: lan966x: add support for interrupts from analyzer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In one of the error paths of the device_for_each_child_node() loop
in hns_mac_init, add missing call to fwnode_handle_put.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, there are some querying mailboxes sent from VF to PF,
and VF will wait the PF's handling result. For mailbox
HCLGE_MBX_GET_QID_IN_PF and HCLGE_MBX_GET_RSS_KEY, it may fail
when the input parameter is invalid, but the prototype of their
handler function is void. In this case, PF always return success
to VF, which may cause the VF get incorrect result.
Fixes it by adding return value for these function.
Fixes: 63b1279d9905 ("net: hns3: check queue id range before using")
Fixes: 532cfc0df1e4 ("net: hns3: add a check for index in hclge_get_rss_key()")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add validity check for message data length in function
hclge_send_mbx_msg(), avoid unexpected overflow.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, function hclge_get_ring_chain_from_mbx will return -ENOMEM if
ring_num is bigger than HCLGE_MBX_MAX_RING_CHAIN_PARAM_NUM. It is better to
return -EINVAL for the invalid parameter case.
So this patch fixes it by return -EINVAL in this abnormal branch.
Fixes: 5d02a58dae60 ("net: hns3: fix for buffer overflow smatch warning")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comments in function hclge_comm_tqps_update_stats is not right,
so fix it.
Fixes: 287db5c40d15 ("net: hns3: create new set of common tqp stats APIs for PF and VF reuse")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For debugfs node rx/tx_queue_info and rx/tx_bd_info, their output info is
aligned to the right, it's not aligned with output of other debugfs node,
so uniform their output info.
Fixes: 907676b13071 ("net: hns3: use tx bounce buffer for small packets")
Fixes: e44c495d95e0 ("net: hns3: refactor queue info of debugfs")
Fixes: 77e9184869c9 ("net: hns3: refactor dump bd info of debugfs")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If failed to register netdev, it needs to clear INITED state and stop
client in case of cause problem when concurrency with uninitialized
process of driver.
Fixes: a289a7e5c1d4 ("net: hns3: put off calling register_netdev() until client initialize complete")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull FireWire fixes
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
card->local_node and card->bm_retries are both always accessed under
card->lock.
fw_core_handle_bus_reset has a check whose condition depends on
card->local_node and whose body writes to card->bm_retries.
Both of these accesses are not under card->lock. Move the lock acquiring
of card->lock to before this check such that these accesses do happen
when card->lock is held.
fw_destroy_nodes is called inside the check.
Since fw_destroy_nodes already acquires card->lock inside its function
body, move this out to the callsites of fw_destroy_nodes.
Also add a comment to indicate which locking is necessary when calling
fw_destroy_nodes.
Cc: <stable@vger.kernel.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When list_for_each_entry() completes the iteration over the whole list
without breaking the loop, the iterator value will be a bogus pointer
computed based on the head element.
While it is safe to use the pointer to determine if it was computed
based on the head element, either with list_entry_is_head() or
&pos->member == head, using the iterator variable after the loop should
be avoided.
In preparation to limit the scope of a list iterator to the list
traversal loop, use a dedicated pointer to point to the found element [1].
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
&e->event and e point to the same address, and &e->event could
be freed in queue_event. So there is a potential uaf issue if
we dereference e after calling queue_event(). Fix this by adding
a temporary variable to maintain e->client in advance, this can
avoid the potential uaf issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
--------------------------------------------
unreferenced object 0xffff000010742a00 (size 128):
comm "swapper/0", pid 1, jiffies 4294902015 (age 1187.652s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000b4dfebaa>] __kmalloc+0x338/0x474
[<00000000d6e716db>] sun50i_cpufreq_nvmem_probe+0xc4/0x36c
[<000000007d6082a0>] platform_probe+0x98/0x11c
[<00000000c990f549>] really_probe+0x234/0x5a0
[<000000002d9fecc6>] __driver_probe_device+0x194/0x224
[<00000000cf0b94fa>] driver_probe_device+0x64/0x13c
[<00000000f238e4cf>] __device_attach_driver+0xf8/0x180
[<000000006720e418>] bus_for_each_drv+0xf8/0x160
[<00000000df4f14f6>] __device_attach+0x174/0x29c
[<00000000782002fb>] device_initial_probe+0x20/0x30
[<00000000c2681b06>] bus_probe_device+0xfc/0x110
[<00000000964cf3bd>] device_add+0x5f0/0xcd0
[<000000004b9264e3>] platform_device_add+0x198/0x390
[<00000000fa82a9d0>] platform_device_register_full+0x178/0x210
[<000000009a5daf13>] sun50i_cpufreq_init+0xf8/0x168
[<000000000377cc7c>] do_one_initcall+0xe4/0x570
--------------------------------------------
if sun50i_cpufreq_get_efuse failed, then opp_tables leak.
Fixes: f328584f7bff ("cpufreq: Add sun50i nvmem based CPU scaling driver")
Signed-off-by: Xiaobing Luo <luoxiaobing0926@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
We have now seen panel (XMG Core 15 e21 laptop) advertizing support
for Intel proprietary eDP backlight control via DPCD registers, but
actually working only with legacy pwm control.
This patch adds panel EDID check for possible HDR static metadata and
Intel proprietary eDP backlight control is used only if that exists.
Missing HDR static metadata is ignored if user specifically asks for
Intel proprietary eDP backlight control via enable_dpcd_backlight
parameter.
v2 :
- Ignore missing HDR static metadata if Intel proprietary eDP
backlight control is forced via i915.enable_dpcd_backlight
- Printout info message if panel is missing HDR static metadata and
support for Intel proprietary eDP backlight control is detected
Fixes: 4a8d79901d5b ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5284
Cc: Lyude Paul <lyude@redhat.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Filippo Falezza <filippo.falezza@outlook.it>
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220413082826.120634-1-jouni.hogander@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit b4b157577cb1de13bee8bebc3576f1de6799a921)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Commit 428cb15d5b00 ("drm/i915: Clean up pre-skl primary plane registers")
introduced DISP_POS_Y and DISP_HEIGHT defines but accidentally set these
their masks to REG_GENMASK(31, 0) instead of REG_GENMASK(31, 16).
This breaks the primary display pane on at least pineview machines, fix
the mask to fix the primary display pane only showing black.
Tested on an Acer One AO532h with an Intel N450 SoC.
Fixes: 428cb15d5b00 ("drm/i915: Clean up pre-skl primary plane registers")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220418150936.5499-1-hdegoede@redhat.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 681f8a5c6e372dbfd2a313ace417e7749543de1d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Because some newer hardware variants have multiple possible parents for
the RTC's timekeeping clock, this driver models it as a "rtc-32k" clock.
However, it does not add any consumer for this clock. This causes the
common clock framework to disable it, preventing RTC time access.
Since the RTC's timekeeping clock should always be enabled, regardless
of which drivers are loaded, let's mark this clock as critical instead
of adding a consumer in the RTC driver.
Fixes: d91612d7f01a ("clk: sunxi-ng: Add support for the sun6i RTC clocks")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220411050100.40964-1-samuel@sholland.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
- Read the reported error count from the proper register on
synopsys_edac
* tag 'edac_urgent_for_v5.18_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/synopsys: Read the error count from the correct register
|
|
Reading EEPROM fails with following warning:
[ 16.357496] ------------[ cut here ]------------
[ 16.357529] fsl_spi b01004c0.spi: rejecting DMA map of vmalloc memory
[ 16.357698] WARNING: CPU: 0 PID: 371 at include/linux/dma-mapping.h:326 fsl_spi_cpm_bufs+0x2a0/0x2d8
[ 16.357775] CPU: 0 PID: 371 Comm: od Not tainted 5.16.11-s3k-dev-01743-g19beecbfe9d6-dirty #109
[ 16.357806] NIP: c03fbc9c LR: c03fbc9c CTR: 00000000
[ 16.357825] REGS: e68d9b20 TRAP: 0700 Not tainted (5.16.11-s3k-dev-01743-g19beecbfe9d6-dirty)
[ 16.357849] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 24002282 XER: 00000000
[ 16.357931]
[ 16.357931] GPR00: c03fbc9c e68d9be0 c26d06a0 00000039 00000001 c0d36364 c0e96428 00000027
[ 16.357931] GPR08: 00000001 00000000 00000023 3fffc000 24002282 100d3dd6 100a2ffc 00000000
[ 16.357931] GPR16: 100cd280 100b0000 00000000 aff54f7e 100d0000 100d0000 00000001 100cf328
[ 16.357931] GPR24: 100cf328 00000000 00000003 e68d9e30 c156b410 e67ab4c0 e68d9d38 c24ab278
[ 16.358253] NIP [c03fbc9c] fsl_spi_cpm_bufs+0x2a0/0x2d8
[ 16.358292] LR [c03fbc9c] fsl_spi_cpm_bufs+0x2a0/0x2d8
[ 16.358325] Call Trace:
[ 16.358336] [e68d9be0] [c03fbc9c] fsl_spi_cpm_bufs+0x2a0/0x2d8 (unreliable)
[ 16.358388] [e68d9c00] [c03fcb44] fsl_spi_bufs.isra.0+0x94/0x1a0
[ 16.358436] [e68d9c20] [c03fd970] fsl_spi_do_one_msg+0x254/0x3dc
[ 16.358483] [e68d9cb0] [c03f7e50] __spi_pump_messages+0x274/0x8a4
[ 16.358529] [e68d9ce0] [c03f9d30] __spi_sync+0x344/0x378
[ 16.358573] [e68d9d20] [c03fb52c] spi_sync+0x34/0x60
[ 16.358616] [e68d9d30] [c03b4dec] at25_ee_read+0x138/0x1a8
[ 16.358667] [e68d9e50] [c04a8fb8] bin_attr_nvmem_read+0x98/0x110
[ 16.358725] [e68d9e60] [c0204b14] kernfs_fop_read_iter+0xc0/0x1fc
[ 16.358774] [e68d9e80] [c0168660] vfs_read+0x284/0x410
[ 16.358821] [e68d9f00] [c016925c] ksys_read+0x6c/0x11c
[ 16.358863] [e68d9f30] [c00160e0] ret_from_syscall+0x0/0x28
...
[ 16.359608] ---[ end trace a4ce3e34afef0cb5 ]---
[ 16.359638] fsl_spi b01004c0.spi: unable to map tx dma
This is due to the AT25 driver using buffers on stack, which is not
possible with CONFIG_VMAP_STACK.
As mentionned in kernel Documentation (Documentation/spi/spi-summary.rst):
- Follow standard kernel rules, and provide DMA-safe buffers in
your messages. That way controller drivers using DMA aren't forced
to make extra copies unless the hardware requires it (e.g. working
around hardware errata that force the use of bounce buffering).
Modify the driver to use a buffer located in the at25 device structure
which is allocated via kmalloc during probe.
Protect writes in this new buffer with the driver's mutex.
Fixes: b587b13a4f67 ("[PATCH] SPI eeprom driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/230a9486fc68ea0182df46255e42a51099403642.1648032613.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The irq_of_parse_and_map() function returns 0 on failure, and does not
return an negative value.
Fixes: cefc03e5995e ("pinctrl: Add Pistachio SoC pin control driver")
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Link: https://lore.kernel.org/r/20220424031430.3170759-1-lv.ruyi@zte.com.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One fix for an information leak caused by copying a buffer to
userspace without checking for error first in the sr driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sr: Do not leak information in ioctl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"A simple cleanup patch and a refcount fix for Xen on Arm"
* tag 'for-linus-5.18-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: Fix some refcount leaks
xen: Convert kmap() to kmap_local_page()
|
|
Pull more drm fixes from Dave Airlie:
"Maarten was away, so Maxine stepped up and sent me the drm-fixes
merge, so no point leaving it for another week.
The big change is an OF revert around bridge/panels, it may have some
driver fallout, but hopefully this revert gets them shook out in the
next week easier.
Otherwise it's a bunch of locking/refcounts across drivers, a radeon
dma_resv logic fix and some raspberry pi panel fixes.
panel:
- revert of patch that broke panel/bridge issues
dma-buf:
- remove unused header file.
amdgpu:
- partial revert of locking change
radeon:
- fix dma_resv logic inversion
panel:
- pi touchscreen panel init fixes
vc4:
- build fix
- runtime pm refcount fix
vmwgfx:
- refcounting fix"
* tag 'drm-fixes-2022-04-23' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: partial revert "remove ctx->lock" v2
Revert "drm: of: Lookup if child node has panel or bridge"
Revert "drm: of: Properly try all possible cases for bridge/panel detection"
drm/vc4: Use pm_runtime_resume_and_get to fix pm_runtime_get_sync() usage
drm/vmwgfx: Fix gem refcounting and memory evictions
drm/vc4: Fix build error when CONFIG_DRM_VC4=y && CONFIG_RASPBERRYPI_FIRMWARE=m
drm/panel/raspberrypi-touchscreen: Initialise the bridge in prepare
drm/panel/raspberrypi-touchscreen: Avoid NULL deref if not initialised
dma-buf-map: remove renamed header file
drm/radeon: fix logic inversion in radeon_sync_resv
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- a new set of keycodes to be used by marine navigation systems
- minor fixes to omap4-keypad and cypress-sf drivers
* tag 'input-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: add Marine Navigation Keycodes
Input: omap4-keypad - fix pm_runtime_get_sync() error checking
Input: cypress-sf - register a callback to disable the regulators
|
|
Pull block fixes from Jens Axboe:
"Just two small regression fixes for bcache"
* tag 'block-5.18-2022-04-22' of git://git.kernel.dk/linux-block:
bcache: fix wrong bdev parameter when calling bio_alloc_clone() in do_bio_hook()
bcache: put bch_bio_map() back to correct location in journal_write_unlocked()
|
|
Commit aa63a74d4535 ("topology/sysfs: Hide PPIN on systems that do not
support it.") caused a build warning on some configurations:
drivers/base/topology.c: In function 'topology_is_visible':
drivers/base/topology.c:158:24: warning: unused variable 'dev' [-Wunused-variable]
158 | struct device *dev = kobj_to_dev(kobj);
Fix this up by getting rid of the variable entirely.
Fixes: aa63a74d4535 ("topology/sysfs: Hide PPIN on systems that do not support it.")
Cc: Tony Luck <tony.luck@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220422062653.3899972-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.18-rc4
Here's a fix for a potential overflow issue in the whiteheat driver when
using the old ARM ABI.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: whiteheat: fix heap overflow in WHITEHEAT_GET_DTR_RTS
USB: serial: cp210x: add PIDs for Kamstrup USB Meter Reader
USB: serial: option: add support for Cinterion MV32-WA/MV32-WB
USB: serial: option: add Telit 0x1057, 0x1058, 0x1075 compositions
|
|
In Chrome OS, a large number of crashes is observed due to corrupted timer
lists. Steven Rostedt pointed out that this usually happens when a timer
is freed while still active, and that the problem is often triggered
by code calling del_timer() instead of del_timer_sync() just before
freeing.
Steven also identified the iwlwifi driver as one of the possible culprits
since it does exactly that.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Gregory Greenman <gregory.greenman@intel.com>
Fixes: 60e8abd9d3e91 ("iwlwifi: dbg_ini: add periodic trigger new API support")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # Linux v5.17.3-rc1 and Debian LLVM-14
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220411154210.1870008-1-linux@roeck-us.net
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Two fixes for the raspberrypi panel initialisation, one fix for a logic
inversion in radeon, a build and pm refcounting fix for vc4, two reverts
for drm_of_get_bridge that caused a number of regression and a locking
regression for amdgpu.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422084403.2xrhf3jusdej5yo4@houat
|
|
The reference clock used by the PolarFire SoC's onboard rtc was missing
from the clock driver. Add this clock at the "config" clock level, with
the external reference clock as its parent.
Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-9-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Currently the mpfs clock driver uses a reference clock called the
"msspll", set in the device tree, as the parent for the cpu/axi/ahb
(config) clocks. The frequency of the msspll is determined by the FPGA
bitstream & the bootloader configures the clock to match the bitstream.
The real reference is provided by a 100 or 125 MHz off chip oscillator.
However, the msspll clock is not actually the parent of all clocks on
the system - the reference clock for the rtc/mtimer actually has the
off chip oscillator as its parent.
In order to fix this, add support for reading the configuration of the
msspll & reparent the "config" clocks so that they are derived from
this clock rather than the reference in the device tree.
Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-8-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
