| Age | Commit message (Collapse) | Author |
|---|
|
CLK_ATHENA is another fabric interconnect and should be marked as critical
as with FIC0-3, since disabling it will cause part of the fabric to go
into reset.
Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-3-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The fabric interconnects are on the AXI bus not AHB.
Update their parent clocks to fix this.
Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-2-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fix from Damien Le Moal:
"A single fix to avoid a NULL pointer dereference in the pata_marvell
driver with adapters not supporting DMA, from Zheyu"
* tag 'ata-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_marvell: Check the 'bmdma_addr' beforing reading
|
|
I made a mistake with the commit a6aaa0032424 ("net: ethernet: stmmac:
fix altr_tse_pcs function when using a fixed-link"). I should have
tested against both scenario of having a SGMII interface and one
without.
Without the SGMII PCS TSE adpater, the sgmii_adapter_base address is
NULL, thus a write to this address will fail.
Cc: stable@vger.kernel.org
Fixes: a6aaa0032424 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20220420152345.27415-1-dinguyen@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When we try to transmit an skb with md_dst attached through wireguard
we hit a null pointer dereference in wg_xmit() due to the use of
dst_mtu() which calls into dst_blackhole_mtu() which in turn tries to
dereference dst->dev.
Since wireguard doesn't use md_dsts we should use skb_valid_dst(), which
checks for DST_METADATA flag, and if it's set, then falls back to
wireguard's device mtu. That gives us the best chance of transmitting
the packet; otherwise if the blackhole netdev is used we'd get
ETH_MIN_MTU.
[ 263.693506] BUG: kernel NULL pointer dereference, address: 00000000000000e0
[ 263.693908] #PF: supervisor read access in kernel mode
[ 263.694174] #PF: error_code(0x0000) - not-present page
[ 263.694424] PGD 0 P4D 0
[ 263.694653] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 263.694876] CPU: 5 PID: 951 Comm: mausezahn Kdump: loaded Not tainted 5.18.0-rc1+ #522
[ 263.695190] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1.fc35 04/01/2014
[ 263.695529] RIP: 0010:dst_blackhole_mtu+0x17/0x20
[ 263.695770] Code: 00 00 00 0f 1f 44 00 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8b 47 10 48 83 e0 fc 8b 40 04 85 c0 75 09 48 8b 07 <8b> 80 e0 00 00 00 c3 66 90 0f 1f 44 00 00 48 89 d7 be 01 00 00 00
[ 263.696339] RSP: 0018:ffffa4a4422fbb28 EFLAGS: 00010246
[ 263.696600] RAX: 0000000000000000 RBX: ffff8ac9c3553000 RCX: 0000000000000000
[ 263.696891] RDX: 0000000000000401 RSI: 00000000fffffe01 RDI: ffffc4a43fb48900
[ 263.697178] RBP: ffffa4a4422fbb90 R08: ffffffff9622635e R09: 0000000000000002
[ 263.697469] R10: ffffffff9b69a6c0 R11: ffffa4a4422fbd0c R12: ffff8ac9d18b1a00
[ 263.697766] R13: ffff8ac9d0ce1840 R14: ffff8ac9d18b1a00 R15: ffff8ac9c3553000
[ 263.698054] FS: 00007f3704c337c0(0000) GS:ffff8acaebf40000(0000) knlGS:0000000000000000
[ 263.698470] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 263.698826] CR2: 00000000000000e0 CR3: 0000000117a5c000 CR4: 00000000000006e0
[ 263.699214] Call Trace:
[ 263.699505] <TASK>
[ 263.699759] wg_xmit+0x411/0x450
[ 263.700059] ? bpf_skb_set_tunnel_key+0x46/0x2d0
[ 263.700382] ? dev_queue_xmit_nit+0x31/0x2b0
[ 263.700719] dev_hard_start_xmit+0xd9/0x220
[ 263.701047] __dev_queue_xmit+0x8b9/0xd30
[ 263.701344] __bpf_redirect+0x1a4/0x380
[ 263.701664] __dev_queue_xmit+0x83b/0xd30
[ 263.701961] ? packet_parse_headers+0xb4/0xf0
[ 263.702275] packet_sendmsg+0x9a8/0x16a0
[ 263.702596] ? _raw_spin_unlock_irqrestore+0x23/0x40
[ 263.702933] sock_sendmsg+0x5e/0x60
[ 263.703239] __sys_sendto+0xf0/0x160
[ 263.703549] __x64_sys_sendto+0x20/0x30
[ 263.703853] do_syscall_64+0x3b/0x90
[ 263.704162] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 263.704494] RIP: 0033:0x7f3704d50506
[ 263.704789] Code: 48 c7 c0 ff ff ff ff eb b7 66 2e 0f 1f 84 00 00 00 00 00 90 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 11 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 72 c3 90 55 48 83 ec 30 44 89 4c 24 2c 4c 89
[ 263.705652] RSP: 002b:00007ffe954b0b88 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[ 263.706141] RAX: ffffffffffffffda RBX: 0000558bb259b490 RCX: 00007f3704d50506
[ 263.706544] RDX: 000000000000004a RSI: 0000558bb259b7b2 RDI: 0000000000000003
[ 263.706952] RBP: 0000000000000000 R08: 00007ffe954b0b90 R09: 0000000000000014
[ 263.707339] R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffe954b0b90
[ 263.707735] R13: 000000000000004a R14: 0000558bb259b7b2 R15: 0000000000000001
[ 263.708132] </TASK>
[ 263.708398] Modules linked in: bridge netconsole bonding [last unloaded: bridge]
[ 263.708942] CR2: 00000000000000e0
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Link: https://github.com/cilium/cilium/issues/19428
Reported-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is no need to add new compatible strings for each new supported
chip version. The compatible string is used only to select the subdriver
(rtl8365mb.c or rtl8366rb.c). Once in the subdriver, it will detect the
chip model by itself, ignoring which compatible string was used.
Link: https://lore.kernel.org/netdev/20220414014055.m4wbmr7tdz6hsa3m@bang-olufsen.dk/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20220418233558.13541-2-luizluca@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current EOI handler for LEVEL triggered interrupts calls clk_enable(),
register IO, clk_disable(). The clock manipulation requires locking which
happens with IRQs disabled in clk_enable_lock(). Instead of turning the
clock on and off all the time, enable the clock in case LEVEL interrupt is
requested and keep the clock enabled until all LEVEL interrupts are freed.
The LEVEL interrupts are an exception on this platform and seldom used, so
this does not affect the common case.
This simplifies the LEVEL interrupt handling considerably and also fixes
the following splat found when using preempt-rt:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/locking/rtmutex.c:2040 __rt_mutex_trylock+0x37/0x62
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.109-rt65-stable-standard-00068-g6a5afc4b1217 #85
Hardware name: STM32 (Device Tree Support)
[<c010a45d>] (unwind_backtrace) from [<c010766f>] (show_stack+0xb/0xc)
[<c010766f>] (show_stack) from [<c06353ab>] (dump_stack+0x6f/0x84)
[<c06353ab>] (dump_stack) from [<c01145e3>] (__warn+0x7f/0xa4)
[<c01145e3>] (__warn) from [<c063386f>] (warn_slowpath_fmt+0x3b/0x74)
[<c063386f>] (warn_slowpath_fmt) from [<c063b43d>] (__rt_mutex_trylock+0x37/0x62)
[<c063b43d>] (__rt_mutex_trylock) from [<c063c053>] (rt_spin_trylock+0x7/0x16)
[<c063c053>] (rt_spin_trylock) from [<c036a2f3>] (clk_enable_lock+0xb/0x80)
[<c036a2f3>] (clk_enable_lock) from [<c036ba69>] (clk_core_enable_lock+0x9/0x18)
[<c036ba69>] (clk_core_enable_lock) from [<c034e9f3>] (stm32_gpio_get+0x11/0x24)
[<c034e9f3>] (stm32_gpio_get) from [<c034ef43>] (stm32_gpio_irq_trigger+0x1f/0x48)
[<c034ef43>] (stm32_gpio_irq_trigger) from [<c014aa53>] (handle_fasteoi_irq+0x71/0xa8)
[<c014aa53>] (handle_fasteoi_irq) from [<c0147111>] (generic_handle_irq+0x19/0x22)
[<c0147111>] (generic_handle_irq) from [<c014752d>] (__handle_domain_irq+0x55/0x64)
[<c014752d>] (__handle_domain_irq) from [<c0346f13>] (gic_handle_irq+0x53/0x64)
[<c0346f13>] (gic_handle_irq) from [<c0100ba5>] (__irq_svc+0x65/0xc0)
Exception stack(0xc0e01f18 to 0xc0e01f60)
1f00: 0000300c 00000000
1f20: 0000300c c010ff01 00000000 00000000 c0e00000 c0e07714 00000001 c0e01f78
1f40: c0e07758 00000000 ef7cd0ff c0e01f68 c010554b c0105542 40000033 ffffffff
[<c0100ba5>] (__irq_svc) from [<c0105542>] (arch_cpu_idle+0xc/0x1e)
[<c0105542>] (arch_cpu_idle) from [<c063be95>] (default_idle_call+0x21/0x3c)
[<c063be95>] (default_idle_call) from [<c01324f7>] (do_idle+0xe3/0x1e4)
[<c01324f7>] (do_idle) from [<c01327b3>] (cpu_startup_entry+0x13/0x14)
[<c01327b3>] (cpu_startup_entry) from [<c0a00c13>] (start_kernel+0x397/0x3d4)
[<c0a00c13>] (start_kernel) from [<00000000>] (0x0)
---[ end trace 0000000000000002 ]---
Power consumption measured on STM32MP157C DHCOM SoM is not increased or
is below noise threshold.
Fixes: 47beed513a85b ("pinctrl: stm32: Add level interrupt support to gpio irq chip")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Fabien Dessenne <fabien.dessenne@foss.st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
To: linux-gpio@vger.kernel.org
Reviewed-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Link: https://lore.kernel.org/r/20220421140827.214088-1-marex@denx.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
All the entries are sorted according to num/pin except for two
entries. Sort them too.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20220420142432.248565-2-luca.ceresoli@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some of the pinmuxing bits described in rk3308_mux_recalced_data are wrong,
pointing to non-existing registers.
Fix the entire table.
Also add a comment in front of each entry with the same string that appears
in the datasheet to make the table easier to compare with the docs.
This fix has been tested on real hardware for the gpio3b3_sel entry.
Fixes: 7825aeb7b208 ("pinctrl: rockchip: add rk3308 SoC support")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20220420142432.248565-1-luca.ceresoli@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into fixes
Samsung pinctrl drivers fixes for v5.18
1. Fix sparse warning introduced in v5.18-rc1.
2. Fix possible unmet Kconfig dependency with COMPILE_TEST, present
since v4.3 or earlier.
|
|
Commit 5467801f1fcb ("gpio: Restrict usage of GPIO chip irq members
before initialization") attempted to fix a race condition that lead to a
NULL pointer, but in the process caused a regression for _AEI/_EVT
declared GPIOs.
This manifests in messages showing deferred probing while trying to
allocate IRQs like so:
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x0000 to IRQ, err -517
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x002C to IRQ, err -517
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x003D to IRQ, err -517
[ .. more of the same .. ]
The code for walking _AEI doesn't handle deferred probing and so this
leads to non-functional GPIO interrupts.
Fix this issue by moving the call to `acpi_gpiochip_request_interrupts`
to occur after gc->irc.initialized is set.
Fixes: 5467801f1fcb ("gpio: Restrict usage of GPIO chip irq members before initialization")
Link: https://lore.kernel.org/linux-gpio/BL1PR12MB51577A77F000A008AA694675E2EF9@BL1PR12MB5157.namprd12.prod.outlook.com/
Link: https://bugzilla.suse.com/show_bug.cgi?id=1198697
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215850
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1979
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1976
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Shreeya Patel <shreeya.patel@collabora.com>
Tested-By: Samuel Čavoj <samuel@cavoj.net>
Tested-By: lukeluk498@gmail.com Link:
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-and-tested-by: Takashi Iwai <tiwai@suse.de>
Cc: Shreeya Patel <shreeya.patel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes Palmer Dabbelt:
- A pair of build fixes for the recent cpuidle driver
- A fix for systems without sv57 that manifests as a crash
early in boot
* tag 'riscv-for-linus-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: cpuidle: fix Kconfig select for RISCV_SBI_CPUIDLE
RISC-V: mm: Fix set_satp_mode() for platform not having Sv57
cpuidle: riscv: support non-SMP config
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"There's no real pattern to the fixes, but the main one fixes our
pmd_leaf() definition to resolve a NULL dereference on the migration
path.
- Fix PMU event validation in the absence of any event counters
- Fix allmodconfig build using clang in conjunction with binutils
- Fix definitions of pXd_leaf() to handle PROT_NONE entries
- More typo fixes"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: fix p?d_leaf()
arm64: fix typos in comments
arm64: Improve HAVE_DYNAMIC_FTRACE_WITH_REGS selection for clang
arm_pmu: Validate single/group leader events
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"At this time, the majority of changes are for pending ASoC fixes while
a few usual HD-audio and USB-audio quirks are found.
Almost all patches are small device-specific fixes, and nothing
worrisome stands out, so far"
* tag 'sound-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (37 commits)
ALSA: hda/realtek: Add quirk for Clevo NP70PNP
ALSA: hda: intel-dsp-config: Add RaptorLake PCI IDs
ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on EliteBook 845/865 G9
ALSA: usb-audio: Clear MIDI port active flag after draining
ALSA: usb-audio: add mapping for MSI MAG X570S Torpedo MAX.
ALSA: hda/i915: Fix one too many pci_dev_put()
ALSA: hda/hdmi: add HDMI codec VID for Raptorlake-P
ALSA: hda/hdmi: fix warning about PCM count when used with SOF
sound/oss/dmasound: fix 'dmasound_setup' defined but not used
firmware: cs_dsp: Fix overrun of unterminated control name string
ASoC: codecs: Fix an error handling path in (rx|tx|va)_macro_probe()
ASoC: Intel: sof_es8336: Add a quirk for Huawei Matebook D15
ASoC: Intel: sof_es8336: add a quirk for headset at mic1 port
ASoC: Intel: sof_es8336: support a separate gpio to control headphone
ASoC: Intel: sof_es8336: simplify speaker gpio naming
ASoC: wm8731: Disable the regulator when probing fails
ASoC: Intel: soc-acpi: correct device endpoints for max98373
ASoC: codecs: wcd934x: do not switch off SIDO Buck when codec is in use
ASoC: SOF: topology: Fix memory leak in sof_control_load()
ASoC: SOF: topology: cleanup dailinks on widget unload
...
|
|
Some android userspace is sending BINDER_TYPE_FDA objects with
num_fds=0. Like the previous patch, this is reproducible when
playing a video.
Before commit 09184ae9b575 BINDER_TYPE_FDA objects with num_fds=0
were 'correctly handled', as in no fixup was performed.
After commit 09184ae9b575 we aggregate fixup and skip regions in
binder_ptr_fixup structs and distinguish between the two by using
the skip_size field: if it's 0, then it's a fixup, otherwise skip.
When processing BINDER_TYPE_FDA objects with num_fds=0 we add a
skip region of skip_size=0, and this causes issues because now
binder_do_deferred_txn_copies will think this was a fixup region.
To address that, return early from binder_translate_fd_array to
avoid adding an empty skip region.
Fixes: 09184ae9b575 ("binder: defer copies of pre-patched txn data")
Acked-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Alessandro Astone <ales.astone@gmail.com>
Link: https://lore.kernel.org/r/20220415120015.52684-1-ales.astone@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When handling BINDER_TYPE_FDA object we are pushing a parent fixup
with a certain skip_size but no scatter-gather copy object, since
the copy is handled standalone.
If BINDER_TYPE_FDA is the last children the scatter-gather copy
loop will never stop to skip it, thus we are left with an item in
the parent fixup list. This will trigger the BUG_ON().
This is reproducible in android when playing a video.
We receive a transaction that looks like this:
obj[0] BINDER_TYPE_PTR, parent
obj[1] BINDER_TYPE_PTR, child
obj[2] BINDER_TYPE_PTR, child
obj[3] BINDER_TYPE_FDA, child
Fixes: 09184ae9b575 ("binder: defer copies of pre-patched txn data")
Acked-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Alessandro Astone <ales.astone@gmail.com>
Link: https://lore.kernel.org/r/20220415120015.52684-2-ales.astone@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The userspace governor is still in use on production systems and the
deprecating warning is scary.
Even if we want to get rid of the userspace governor, it is too soon
yet as the alternatives are not yet adopted.
Change the deprecated warning by an information message suggesting to
switch to the netlink thermal events.
Fixes: 0275c9fb0eff ("thermal/core: Make the userspace governor deprecated")
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This reverts commit a67a46af4ad6342378e332b7420c1d1a2818c53f.
It has been reported the warning is annoying as the cooling device
state is still needed on some production system.
Meanwhile we provide a way to consolidate the thermal framework to
prevent multiple actors acting on the cooling devices with conflicting
decisions, let's revert this warning.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23ca ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 states that the Modem Status
Command (MSC) shall only be used if the basic option was chosen.
The current implementation uses MSC frames even if advanced option was
chosen to inform the peer about modem line state updates. A standard
conform peer may choose to discard these frames in advanced option mode.
Furthermore, gsmtty_modem_update() is not part of the 'tty_operations'
functions despite its name.
Rename gsmtty_modem_update() to gsm_modem_update() to clarify this. Split
its function into gsm_modem_upd_via_data() and gsm_modem_upd_via_msc()
depending on the encoding and adaption. Introduce gsm_dlci_modem_output()
as adaption of gsm_dlci_data_output() to encode and queue empty frames in
advanced option mode. Use it in gsm_modem_upd_via_data().
gsm_modem_upd_via_msc() is based on the initial gsmtty_modem_update()
function which used only MSC frames to update modem states.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dynamic virtual tty registration was introduced to allow the user to handle
these cases with uevent rules. The following commits relate to this:
Commit 5b87686e3203 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Commit 0b91b5332368 ("tty: n_gsm: Save dlci address open status when config requester")
Commit 46292622ad73 ("tty: n_gsm: clean up indenting in gsm_queue()")
However, the following behavior can be seen with this implementation:
- n_gsm ldisc is activated via ioctl
- all configuration parameters are set to their default value (initiator=0)
- the mux gets activated and attached and gsmtty0 is being registered in
in gsm_dlci_open() after DLCI 0 was established (DLCI 0 is the control
channel)
- the user configures n_gsm via ioctl GSMIOC_SETCONF as initiator
- this re-attaches the n_gsm mux
- no new gsmtty devices are registered in gsmld_attach_gsm() because the
mux is already active
- the initiator side registered only the control channel as gsmtty0
(which should never happen) and no user channel tty
The commits above make it impossible to operate the initiator side as no
user channel tty is or will be available.
On the other hand, this behavior will make it also impossible to allow DLCI
parameter negotiation on responder side in the future. The responder side
first needs to provide a device for the application before the application
can set its parameters of the associated DLCI via ioctl.
Note that the user application is still able to detect a link establishment
without relaying to uevent by waiting for DTR open on responder side. This
is the same behavior as on a physical serial interface. And on initiator
side a tty hangup can be detected if a link establishment request failed.
Revert the commits above completely to always register all user channels
and no control channel after mux attachment. No other changes are made.
Fixes: 5b87686e3203 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 927728a34f11b5a27f4610bdb7068317d6fdc72a.
Once the uart_port->rs485->flag is set to SER_RS485_ENABLED, the port
should always work in RS485 mode. If users want the port to leave
RS485 mode, they need to call ioctl() to clear SER_RS485_ENABLED.
So here we shouldn't clear the RS485 bits in the shutdown().
Fixes: 927728a34f11 ("serial: sc16is7xx: Clear RS485 bits in the shutdown")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220418094339.678144-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect fixes for v5.18
This contains a fix for a reported issue on sc7180 platforms, where
one of the resources has been incorrectly modelled as both clock and
interconnect, which is causing a crash when both frameworks try to
manage it. Fix the same issue also on another platform that appears
to be affected by the same.
- interconnect: qcom: sc7180: Drop IP0 interconnects
- interconnect: qcom: sdx55: Drop IP0 interconnects
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: sdx55: Drop IP0 interconnects
interconnect: qcom: sc7180: Drop IP0 interconnects
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-linus
Vinod writes:
phy: fixes for 5.18
Fixes for bunch of drivers:
- TI fixes for runtime disable, missing of_node_put and error handling
- Samsung fixes for device_put and of_node_put
- Amlogic error path handling
* tag 'phy-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: amlogic: fix error path in phy_g12a_usb3_pcie_probe()
phy: ti: Add missing pm_runtime_disable() in serdes_am654_probe
phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe
phy: ti: omap-usb2: Fix error handling in omap_usb2_enable_clocks
phy: ti: tusb1210: Fix an error handling path in tusb1210_probe()
phy: samsung: exynos5250-sata: fix missing device put in probe error paths
phy: samsung: Fix missing of_node_put() in exynos_sata_phy_probe
phy: ti: Fix missing of_node_put in ti_pipe3_get_sysctrl()
phy: ti: tusb1210: Make tusb1210_chg_det_states static
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-linus
Manivannan writes:
MHI fixes for v5.18
Couple of patches fixing the hibernation issue seen on MHI endpoint devices like
SDX65 modems:
- During hibernation, the host puts the device into D3cold after thaw() stage.
But at that time, the device would be in M0 state. So the device emits a
warning (not visible to the host but to device firmware only) stating invalid
transition. This is fixed by adding a poweroff() callback that puts the device
into M3 before D3cold.
- There is a possibility that the recovery worker might be running while trying
to powerdown the device. So flush the recovery worker before that.
* tag 'mhi-fixes-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
bus: mhi: host: pci_generic: Flush recovery worker during freeze
bus: mhi: host: pci_generic: Add missing poweroff() PM callback
|
|
Make sure not to set run_stop bit or link state change request while
initiating soft-reset. Register read-modify-write operation may
unintentionally start the controller before the initialization completes
with its previous DCTL value, which can cause initialization failure.
Fixes: f59dcab17629 ("usb: dwc3: core: improve reset sequence")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6aecbd78328f102003d40ccf18ceeebd411d3703.1650594792.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tegra194 and Tegra234 SoCs have the erratum that causes walk cache
entries to not be invalidated correctly. The problem is that the walk
cache index generated for IOVA is not same across translation and
invalidation requests. This is leading to page faults when PMD entry is
released during unmap and populated with new PTE table during subsequent
map request. Disabling large page mappings avoids the release of PMD
entry and avoid translations seeing stale PMD entry in walk cache.
Fix this by limiting the page mappings to PAGE_SIZE for Tegra194 and
Tegra234 devices. This is recommended fix from Tegra hardware design
team.
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Krishna Reddy <vdumpa@nvidia.com>
Co-developed-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Link: https://lore.kernel.org/r/20220421081504.24678-1-amhetre@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
If major equal 0, register_chrdev() returns error code when it fails.
This function dynamically allocate a major and return its number on
success, so we should use "< 0" to check it instead of "!".
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-By: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Extra quiet after Easter, only have minor i915 and msm pulls. However
I haven't seen a PR from our misc tree in a little while, I've cc'ed
all the suspects. Once that unblocks I expect a bit larger bunch of
patches to arrive.
Otherwise as I said, one msm revert and two i915 fixes.
msm:
- revert iommu change that broke some platforms.
i915:
- Unset enable_psr2_sel_fetch if PSR2 detection fails
- Fix to detect when VRR is turned off from panel settings"
* tag 'drm-fixes-2022-04-22' of git://anongit.freedesktop.org/drm/drm:
drm/i915/display/psr: Unset enable_psr2_sel_fetch if other checks in intel_psr2_config_valid() fails
drm/msm: Revert "drm/msm: Stop using iommu_present()"
drm/i915/display/vrr: Reset VRR capable property on a long hpd
|
|
Since the commit 948fb0969eae ("clk: Always clamp the rounded rate"),
the clk_core_determine_round_nolock() would clamp the requested rate
between min and max rates from the rate request. Normally these fields
would be filled by clk_core_get_boundaries() called from
clk_round_rate().
However clk_gfx3d_determine_rate() uses a manually crafted rate request,
which did not have these fields filled. Thus the requested frequency
would be clamped to 0, resulting in weird frequencies being requested
from the hardware.
Fix this by filling min_rate and max_rate to the values valid for the
respective PLLs (0 and ULONG_MAX).
Fixes: 948fb0969eae ("clk: Always clamp the rounded rate")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220419235447.1586192-1-dmitry.baryshkov@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reported-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The current clock driver for PolarFire SoC puts the hardware behind
"periph" clocks into reset if their clock is disabled. CONFIG_PM was
recently added to the riscv defconfig and exposed issues caused by this
behaviour, where the Cadence GEM was being put into reset between its
bringup & the PHY bringup:
https://lore.kernel.org/linux-riscv/9f4b057d-1985-5fd3-65c0-f944161c7792@microchip.com/
Fix this (for now) by removing the reset from mpfs_periph_clk_disable.
Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220411072340.740981-1-conor.dooley@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Before detecting the cable type on the dma bar, the driver should check
whether the 'bmdma_addr' is zero, which means the adapter does not
support DMA, otherwise we will get the following error:
[ 5.146634] Bad IO access at port 0x1 (return inb(port))
[ 5.147206] WARNING: CPU: 2 PID: 303 at lib/iomap.c:44 ioread8+0x4a/0x60
[ 5.150856] RIP: 0010:ioread8+0x4a/0x60
[ 5.160238] Call Trace:
[ 5.160470] <TASK>
[ 5.160674] marvell_cable_detect+0x6e/0xc0 [pata_marvell]
[ 5.161728] ata_eh_recover+0x3520/0x6cc0
[ 5.168075] ata_do_eh+0x49/0x3c0
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
Revert to fix iommu regression.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtvPo4xD2peAztDMPP2n4utb7d9WQboMFwsba9E8U2rCw@mail.gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A bunch of driver fixes:
- idxd device RO checks and device cleanup
- dw-edma unaligned access and alignment
- qcom: missing minItems in binding
- mediatek pm usage fix
- imx init script"
* tag 'dmaengine-fix-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dt-bindings: dmaengine: qcom: gpi: Add minItems for interrupts
dmaengine: idxd: skip clearing device context when device is read-only
dmaengine: idxd: add RO check for wq max_transfer_size write
dmaengine: idxd: add RO check for wq max_batch_size write
dmaengine: idxd: fix retry value to be constant for duration of function call
dmaengine: idxd: match type for retries var in idxd_enqcmds()
dmaengine: dw-edma: Fix inconsistent indenting
dmaengine: dw-edma: Fix unaligned 64bit access
dmaengine: mediatek:Fix PM usage reference leak of mtk_uart_apdma_alloc_chan_resources
dmaengine: imx-sdma: Fix error checking in sdma_event_remap
dma: at_xdmac: fix a missing check on list iterator
dmaengine: imx-sdma: fix init of uart scripts
dmaengine: idxd: fix device cleanup on disable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from xfrm and can.
Current release - regressions:
- rxrpc: restore removed timer deletion
Current release - new code bugs:
- gre: fix device lookup for l3mdev use-case
- xfrm: fix egress device lookup for l3mdev use-case
Previous releases - regressions:
- sched: cls_u32: fix netns refcount changes in u32_change()
- smc: fix sock leak when release after smc_shutdown()
- xfrm: limit skb_page_frag_refill use to a single page
- eth: atlantic: invert deep par in pm functions, preventing null
derefs
- eth: stmmac: use readl_poll_timeout_atomic() in atomic state
Previous releases - always broken:
- gre: fix skb_under_panic on xmit
- openvswitch: fix OOB access in reserve_sfa_size()
- dsa: hellcreek: calculate checksums in tagger
- eth: ice: fix crash in switchdev mode
- eth: igc:
- fix infinite loop in release_swfw_sync
- fix scheduling while atomic"
* tag 'net-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
drivers: net: hippi: Fix deadlock in rr_close()
selftests: mlxsw: vxlan_flooding_ipv6: Prevent flooding of unwanted packets
selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets
nfc: MAINTAINERS: add Bug entry
net: stmmac: Use readl_poll_timeout_atomic() in atomic state
doc/ip-sysctl: add bc_forwarding
netlink: reset network and mac headers in netlink_dump()
net: mscc: ocelot: fix broken IP multicast flooding
net: dsa: hellcreek: Calculate checksums in tagger
net: atlantic: invert deep par in pm functions, preventing null derefs
can: isotp: stop timeout monitoring when no first frame was sent
bonding: do not discard lowest hash bit for non layer3+4 hashing
net: lan966x: Make sure to release ptp interrupt
ipv6: make ip6_rt_gc_expire an atomic_t
net: Handle l3mdev in ip_tunnel_init_flow
l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using netdev_master_upper_dev_get_rcu
net/sched: cls_u32: fix possible leak in u32_init_knode()
net/sched: cls_u32: fix netns refcount changes in u32_change()
powerpc: Update MAINTAINERS for ibmvnic and VAS
net: restore alpha order to Ethernet devices in config
...
|
|
Control Flow Integrity (CFI) instrumentation of the kernel noticed that
the caller, dev_attr_show(), and the callback, odvp_show(), did not have
matching function prototypes, which would cause a CFI exception to be
raised. Correct the prototype by using struct device_attribute instead
of struct kobj_attribute.
Reported-and-tested-by: Joao Moreira <joao@overdrivepizza.com>
Link: https://lore.kernel.org/lkml/067ce8bd4c3968054509831fa2347f4f@overdrivepizza.com/
Fixes: 006f006f1e5c ("thermal/int340x_thermal: Export OEM vendor variables")
Cc: 5.8+ <stable@vger.kernel.org> # 5.8+
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This reverts commit bfe55a1f7fd6bfede16078bf04c6250fbca11588.
This was presumably misdiagnosed as an inability to use C3 at
all when I suspect the real problem is just misconfiguration of
C3 vs. ARB_DIS.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Tested-by: Woody Suwalski <wsuwalski@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The "safe state" index is used by acpi_idle_enter_bm() to avoid
entering a C-state that may require bus mastering to be disabled
on entry in the cases when this is not going to happen. For this
reason, it should not be set to point to C3 type of C-states, because
they may require bus mastering to be disabled on entry in principle.
This was broken by commit d6b88ce2eb9d ("ACPI: processor idle: Allow
playing dead in C3 state") which inadvertently allowed the "safe
state" index to point to C3 type of C-states.
This results in a machine that won't boot past the point when it first
enters C3. Restore the correct behaviour (either demote to C1/C2, or
use C3 but also set ARB_DIS=1).
I hit this on a Fujitsu Siemens Lifebook S6010 (P3) machine.
Fixes: d6b88ce2eb9d ("ACPI: processor idle: Allow playing dead in C3 state")
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Woody Suwalski <wsuwalski@gmail.com>
[ rjw: Subject and changelog adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If any function like UVC is deactivating gadget as part of composition
switch which results in not calling pullup enablement, it is not getting
enabled after switch to new composition due to this deactivation flag
not cleared. This results in USB enumeration not happening after switch
to new USB composition. Hence clear deactivation flag inside gadget
structure in configfs_composite_unbind() before switch to new USB
composition.
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220413211038.72797-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is odd to call devm_add_action_or_reset() before calling the function
that should be undone.
Either, the "_or_reset" part should be omitted, or the action should be
recorded after the resources have been allocated.
Switch the order of devm_add_action_or_reset() and usb_role_switch_get().
Fixes: 9a1bf58ccd44 ("usb: misc: eud: Add driver support for Embedded USB Debugger(EUD)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/362908699275ecec078381b42d87c817c6965fc6.1648979948.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit ae8709b296d8 ("USB: core: Make do_proc_control() and
do_proc_bulk() killable") if a device has the USB_QUIRK_DELAY_CTRL_MSG
quirk set, it will temporarily block all other URBs (e.g. interrupts)
while sleeping due to a control.
This results in noticeable delays when, for example, a userspace usbfs
application is sending URB interrupts at a high rate to a keyboard and
simultaneously updates the lock indicators using controls. Interrupts
with direction set to IN are also affected by this, meaning that
delivery of HID reports (containing scancodes) to the usbfs application
is delayed as well.
This patch fixes the regression by calling msleep() while the device
mutex is unlocked, as was the case originally with usb_control_msg().
Fixes: ae8709b296d8 ("USB: core: Make do_proc_control() and do_proc_bulk() killable")
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Link: https://lore.kernel.org/r/3e299e2a-13b9-ddff-7fee-6845e868bc06@tasossah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the PHY controller node has a "port" dwc3 tries to find an
extcon device even when "usb-role-switch" is present. This happens
because dwc3_get_extcon() sees that "port" node and then calls
extcon_find_edev_by_node() which will always return EPROBE_DEFER
in that case.
On the other hand, even if an extcon was present and dwc3_get_extcon()
was successful it would still be ignored in favor of "usb-role-switch".
Let's just first check if "usb-role-switch" is configured in the device
tree and directly use it instead and only try to look for an extcon
device otherwise.
Fixes: 8a0a13799744 ("usb: dwc3: Registering a role switch in the DRD code.")
Cc: stable <stable@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20220411155300.9766-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current driver logic checks against 0 to determine whether the
periodic tx/rx threshold settings are set, but we may get bogus values
from uninitialized variables if no device property is set. Properly
default these variables to 0.
Fixes: 938a5ad1d305 ("usb: dwc3: Check for ESS TX/RX threshold config")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cccfce990b11b730b0dae42f9d217dc6fb988c90.1649727139.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Issue description:
When an OTG port has been switched to device role and then switch back
to host role again, the USB 3.0 Host (XHCI) will not be able to detect
"plug in event of a connected USB 2.0/1.0 ((Highspeed and Fullspeed)
devices until system reboot.
Root cause and Solution:
There is a condition checking flag "ssusb->otg_switch.is_u3_drd" in
toggle_opstate(). At the end of role switch procedure, toggle_opstate()
will be called to set DC_SESSION and SOFT_CONN bit. If "is_u3_drd" was
set and switched the role to USB host 3.0, bit DC_SESSION and SOFT_CONN
will be skipped hence caused the port cannot detect connected USB 2.0
(Highspeed and Fullspeed) devices. Simply remove the condition check to
solve this issue.
Fixes: d0ed062a8b75 ("usb: mtu3: dual-role mode support")
Cc: stable@vger.kernel.org
Tested-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Tainping Fang <tianping.fang@mediatek.com>
Link: https://lore.kernel.org/r/20220419081245.21015-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Alderlake has two XHCI controllers with PCI IDs 0x461e and 0x51ed. We
had previously added the quirk to default enable runtime PM for 0x461e,
now add it for 0x51ed as well.
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220408114225.1.Ibcff6b86ed4eacfe4c4bc89c90e18416f3900a3e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 33fb697ec7e5 ("usb: dwc3: Get clocks individually") moved from
the clk_bulk api to individual clocks, following the snps,dwc3.yaml
dt-binding for clock names.
Unfortunately the rk3328 (and upcoming rk356x support) use the
rockchip,dwc3.yaml which has different clock names, which are common on
devices using the glue layer.
The rk3328 does not use a glue layer, but attaches directly to the dwc3
core driver.
The offending patch series failed to account for this, thus dwc3 was
broken on rk3328.
To retain backwards compatibility with rk3328 device trees we must also
check for the alternate clock names.
Fixes: 33fb697ec7e5 ("usb: dwc3: Get clocks individually")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220409152116.3834354-1-pgwipeout@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_put_dev shouldn't be called when uss720_probe succeeds because of
priv->usbdev. At the same time, priv->usbdev shouldn't be set to NULL
before destroy_priv in uss720_disconnect because usb_put_dev is in
destroy_priv.
Fix this by moving priv->usbdev = NULL after usb_put_dev.
Fixes: dcb4b8ad6a44 ("misc/uss720: fix memory leak in uss720_probe")
Cc: stable <stable@kernel.org>
Reviewed-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220407024001.11761-1-hbh25y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In zhaoxin platform, some ehci projects will latch a wakeup signal
internal when plug in a device on port during system S0. This wakeup
signal will turn on when ehci runtime suspend, which will trigger a
system control interrupt that will resume ehci back to D0. As no
device connect, ehci will be set to runtime suspend and turn on the
internal latched wakeup signal again. It will cause a suspend-resume
loop and generate system control interrupt continuously.
Fixed this issue by clear wakeup signal latched in ehci internal when
ehci resume callback is called.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20220324121735.3803-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
