| Age | Commit message (Collapse) | Author |
|---|
|
IO enable sequencing needs ddi clocks enabled.
These clocks will be gated at a later point in
the enable sequence.
v2: Fix the commit header (Uma)
v3: Remove the redundant read (Ville)
Fixes: 949fc52af19e ("drm/i915/icl: add pll mapping for DSI")
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553513202-13863-1-git-send-email-vandita.kulkarni@intel.com
|
|
Badly-designed systems might have (for example) active-high wake pins
that default to high (e.g., because of external pull ups) until they
have an active firmware which starts driving it low. This can cause an
interrupt storm in the time between request_irq() and disable_irq().
We don't support shared interrupts here, so let's just pre-configure the
interrupt to avoid auto-enabling it.
Fixes: fd913ef7ce61 ("Bluetooth: btusb: Add out-of-band wakeup support")
Fixes: 5364a0b4f4be ("arm64: dts: rockchip: move QCA6174A wakeup pin into its USB node")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
To prevent build fail on some platform which does
not have it in the include file chain.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: a1d2a6339961 ("drm/lima: driver for ARM Mali4xx GPUs")
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190409003617.4470-2-yuq825@gmail.com
|
|
Current implementation does not support MMU-less
plarforms.
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: a1d2a6339961 ("drm/lima: driver for ARM Mali4xx GPUs")
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190409003617.4470-1-yuq825@gmail.com
|
|
This is the third step to make MT2701 HDMI stable.
We should not change the rate of parent for hdmi phy when
doing round_rate for this clock. The parent clock of hdmi
phy must be the same as it. We change it when doing set_rate
only.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
This is the second step to make MT2701 HDMI stable.
The factor depends on the divider of DPI in MT2701, therefore,
we should fix this factor to the right and new one.
Test: search ok
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
This is the first step to make MT2701 hdmi stable.
The parent rate of hdmi phy had set by DPI driver.
We should not set or change the parent rate of MT2701 hdmi phy,
as a result we should remove the flags of "CLK_SET_RATE_PARENT"
from the clock of MT2701 hdmi phy.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Recalculate the rate of this clock, by querying hardware to
make implementation of recalc_rate() to match the definition.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
The Amlogic G12A embeds the same Synopsys DW-HDMI Controller,
but with :
- a "backport" of the HDR signaling registers from more recent
DW-HDMI controllers, this will need a tweak since it's not
normally present on this version of the DW-HDMI controller
- A direct mapping of TOP and DW-HDMI registers instead of an
internal bus accessed using read/write registers
- Support for RX-SENSE, but not yet implemented
- Support for HDMI 2.1 Dynamic HDR, but not yet implemented
- Different registers mapping for the HDMI PHY setup
This patchs adds support for these changes while providing exact
same support as the previous GXBB, GXL & GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-12-narmstrong@baylibre.com
|
|
Finally add the Amlogic G12A SoC compatible for the VPU driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-11-narmstrong@baylibre.com
|
|
While switching to the Common Clock Framework is still Work In Progress,
this patch adds the corresponding G12A HDMI PLL setup to be on-par
with the other SoCs support.
The G12A has only a single tweak about the high frequency setup,
where the HDMI PLL needs a specific setup to handle correctly the
5.94GHz DCO frequency.
Apart that, it handls ecorrectly all the other HDMI frequencies
and can achieve even better DMT clock frequency precision with
the larger fractional dividier width.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-10-narmstrong@baylibre.com
|
|
The Meson G12A SoCs uses the exact same CVBS encoder except a simple
CVBS DAC register offset and settings delta.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed subject typo]
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-9-narmstrong@baylibre.com
|
|
This patch adds support for the new OSD+VD Plane blending module
in the CRTC code by adding the G12A code to manage the blending
module and setting the right OSD1 & VD1 plane registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-8-narmstrong@baylibre.com
|
|
Amlogic G12A SoC supports the same set of Video Planes, but now
are handled by the new OSD plane blender module.
This patch uses the same VD1 plane for G12A, using the exact same scaler
and VD1 setup registers, except using the new blender register to
disable the plane.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fix typo in commit log]
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-7-narmstrong@baylibre.com
|
|
Amlogic G12A SoC supports now up to 3 OSD planes (1 more than the
previous SoCs) and a brand new OSD plane blender module.
This patch uses the same OSD1 plane for G12A, using the exact same scaler
and OSD1 setup registers, except using the new blender register to
disable the plane.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed typo in commit log]
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-6-narmstrong@baylibre.com
|
|
Amlogic G12A SoC needs a different VIU setup code,
handle it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-5-narmstrong@baylibre.com
|
|
Amlogic G12A needs a different VPP setup code, handle it here.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-4-narmstrong@baylibre.com
|
|
This patch adds the new VPU registers added since the
Amlogic GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-3-narmstrong@baylibre.com
|
|
On Amlogic G12A SoC, the 2,97GHz PLL frequency is not stable enough
to provide a correct 297MHz pixel clock, so switch the PLL base
frequency with a /2 OD when the 297MHz pixel clock is requested.
This solves the issue on G12A and also works fine on GXBB, GXL & GXM.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-2-narmstrong@baylibre.com
|
|
Due to a clerical error,there is one zero less for 12800000.
Fix it for 128000000
Fixes: 0fc721b2968e ("drm/mediatek: add hdmi driver for MT2701 and MT7623")
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Circumvent the dance we currently perform to find the preempt_client and
lookup its HW context for this engine, as we know we have already pinned
the preempt_context on the engine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190408091728.20207-15-chris@chris-wilson.co.uk
|
|
ACPICA commit b233720031a480abd438f2e9c643080929d144c3
ASL operation_regions declare a range of addresses that it uses. In a
perfect world, the range of addresses should be used exclusively by
the AML interpreter. The OS can use this information to decide which
drivers to load so that the AML interpreter and device drivers use
different regions of memory.
During table load, the address information is added to a global
address range list. Each node in this list contains an address range
as well as a namespace node of the operation_region. This list is
deleted at ACPI shutdown.
Unfortunately, ASL operation_regions can be declared inside of control
methods. Although this is not recommended, modern firmware contains
such code. New module level code changes unintentionally removed the
functionality of adding and removing nodes to the global address
range list.
A few months ago, support for adding addresses has been re-
implemented. However, the removal of the address range list was
missed and resulted in some systems to crash due to the address list
containing bogus namespace nodes from operation_regions declared in
control methods. In order to fix the crash, this change removes
dynamic operation_regions after control method termination.
Link: https://github.com/acpica/acpica/commit/b2337200
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202475
Fixes: 4abb951b73ff ("ACPICA: AML interpreter: add region addresses in global list during initialization")
Reported-by: Michael J Gruber <mjg@fedoraproject.org>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Cc: 4.20+ <stable@vger.kernel.org> # 4.20+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/mediatek/mtk_hdmi.c:1521:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1509, but without a corresponding object release within this function.
drivers/gpu/drm/mediatek/mtk_hdmi.c:1524:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1509, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Push getting the reference for the encoders' power domains into the
encoder get_power_domains() hook instead of doing this from the caller.
This way the encoder can store away the corresponding wakerefs.
This fixes the DSI encoder disabling, which didn't release these
power references it acquired during HW state readout.
Note that longtime ownership for the corresponding wakerefs can be thus
acquired / released in two ways. Nevertheless there is always only one
owner for them:
After HW readout (booting/system resume):
- encoder->get_power_domains() acquires
- encoder->disable*() releases
After a modeset (calling intel_atomic_commit()):
- encoder->enable*() acquires
- encoder->disable*() releases
* can be any of the encoder enable/disable hooks.
v2:
- Check that the DSI io_wakerefs are unset both during encoder HW
readout and enabling. (Chris)
Fixes: 0e6e0be4c9523 ("drm/i915: Markup paired operations on display power domains")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190407124655.31536-1-imre.deak@intel.com
(cherry picked from commit 3a52fb7e7953f0b13df8c05d0d74b56a66888f30)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Pull networking fixes from David Miller:
1) Off by one and bounds checking fixes in NFC, from Dan Carpenter.
2) There have been many weird regressions in r8169 since we turned ASPM
support on, some are still not understood nor completely resolved.
Let's turn this back off for now. From Heiner Kallweit.
3) Signess fixes for ethtool speed value handling, from Michael
Zhivich.
4) Handle timestamps properly in macb driver, from Paul Thomas.
5) Two erspan fixes, it's the usual "skb ->data potentially reallocated
and we're holding a stale protocol header pointer". From Lorenzo
Bianconi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnxt_en: Reset device on RX buffer errors.
bnxt_en: Improve RX consumer index validity check.
net: macb driver, check for SKBTX_HW_TSTAMP
qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
net: ip_gre: fix possible use-after-free in erspan_rcv
r8169: disable ASPM again
MAINTAINERS: ieee802154: update documentation file pattern
net: vrf: Fix ping failed when vrf mtu is set to 0
selftests: add a tc matchall test case
nfc: nci: Potential off by one in ->pipes[] array
NFC: nci: Add some bounds checking in nci_hci_cmd_received()
|
|
If scsi cmd sglist is not suitable for DDP then csiostor driver uses
preallocated buffers for DDP, because of this data copy is required from
DDP buffer to scsi cmd sglist before calling ->scsi_done().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on. Recover by resetting the device.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem. However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range. Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.
Fixes: fa7e28127a5a ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
calc_tpm2_event_size() has an invalid signature because
it returns a 'size_t' where as its signature says that
it returns 'int'.
Cc: <stable@vger.kernel.org>
Fixes: 4d23cc323cdb ("tpm: add securityfs support for TPM 2.0 firmware event log")
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
The poll condition should only check response_length,
because reads should only be issued if there is data to read.
The response_read flag only prevents double writes.
The problem was that the write set the response_read to false,
enqued a tpm job, and returned. Then application called poll
which checked the response_read flag and returned EPOLLIN.
Then the application called read, but got nothing.
After all that the async_work kicked in.
Added also mutex_lock around the poll check to prevent
other possible race conditions.
Fixes: 9488585b21bef0df12 ("tpm: add support for partial reads")
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Tested-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
tpm_chip_start/stop() should be also called for TPM 1.x devices on
suspend. Add that functionality back. Do not lock the chip because
it is unnecessary as there are no multiple threads using it when
doing the suspend.
Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()")
Reported-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
There's a significant number of reports that re-enabling ASPM causes
different issues, ranging from decreased performance to system not
booting at all. This affects only a minority of users, but the number
of affected users is big enough that we better switch off ASPM again.
This will hurt notebook users who are not affected by the issues, they
may see decreased battery runtime w/o ASPM. With the PCI core folks is
being discussed to add generic sysfs attributes to control ASPM.
Once this is in place brave enough users can re-enable ASPM on their
system.
Fixes: a99790bf5c7f ("r8169: Reinstate ASPM Support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vring_create_virtqueue() allows the caller to specify via the
may_reduce_num parameter whether the vring code is allowed to
allocate a smaller ring than specified.
However, the split ring allocation code tries to allocate a
smaller ring on allocation failure regardless of what the
caller specified. This may cause trouble for e.g. virtio-pci
in legacy mode, which does not support ring resizing. (The
packed ring code does not resize in any case.)
Let's fix this by bailing out immediately in the split ring code
if the requested size cannot be allocated and may_reduce_num has
not been specified.
While at it, fix a typo in the usage instructions.
Fixes: 2a2d1382fe9d ("virtio: Add improved queue allocation API")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
|
|
A couple of machines in the farm show quite frequent errors in the
powerwells not being released. Either there is an external agent
interferring with the powerwells, or the powerwell doesn't quite behave
as we anticipate -- either way, the test is not reliable enough to be
enabled by default in CI. It has served its immediate purpose in
providing coverage as we made tweaks to forcewake, so keep it available
for future testing.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110210
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190407192649.14750-1-chris@chris-wilson.co.uk
|
|
This interlaced mode restriction applies to all gens, not only to
Haswell.
Also while at it updating the debug message to.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406005112.27205-4-jose.souza@intel.com
|
|
Even when driver is reloaded and hits this scenario the PSR mutex
should be initialized, otherwise reading PSR debugfs status will
execute mutex_lock() over a mutex that was not initialized.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406005112.27205-3-jose.souza@intel.com
|
|
PSR support for VLV and CHV was dropped in commit ce3508fd2a77
("drm/i915/psr: Nuke PSR support for VLV and CHV") so no need to keep
this registers around.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406005112.27205-2-jose.souza@intel.com
|
|
Turn out it is not a DMC bug it is actually a HW one, so this
workaround will be needed for current gens, lets update the comment
and remove the FIXME.
BSpec: 7723
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406005112.27205-1-jose.souza@intel.com
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/vmwgfx/vmwgfx_fb.c: In function 'vmw_fb_init':
drivers/gpu/drm/vmwgfx/vmwgfx_fb.c:645:29: warning:
variable 'fb_offset' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/vmwgfx/vmwgfx_fb.c:645:19: warning:
variable 'fb_depth' set but not used [-Wunused-but-set-variable]
They're not used any more, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Deepak Rawat <drawat@vmware.com>
|
|
When building with -Wsometimes-uninitialized, Clang warns:
drivers/gpu/drm/vmwgfx/vmwgfx_execbuf.c:3964:7: warning: variable
'handle' is used uninitialized whenever '?:' condition is false
[-Wsometimes-uninitialized]
It's not wrong; however, in practice, this is never an issue because
the value of handle isn't used when user_fence_rep is NULL because
vmw_execbuf_copy_fence_user returns immediately when that is the case.
Just zero initialize this variable so that Clang no longer warns.
Link: https://github.com/ClangBuiltLinux/linux/issues/397
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Deepak Rawat <drawat@vmware.com>
|
|
Whenever FIFO allocation fails an error message is printed to dmesg.
Since this is common operation a lot of similar messages are scattered
everywhere. Use preprocessor macro to remove this cluttering.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
No functional change with this change, just fixing formatting and
spaces.
v2: Rebase.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
DRM_ERROR overwhelms dmesgi so use VMW_DEBUG_USER instead. Any malformed
command should not really go to device so WARN_ONCE to spot this.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Now that vmw_cmd_check prints debug message whenever a command verifier
fails, some of debug statements are unnecessary. Also rearranged some
debug print-out with this patch.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Whenever command verifier function returns with an error, print a debug
message using VMW_DEBUG_USER. This will make sure failing commands can
be easily tracked for debugging purpose.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Error messages or debugging message reported during user-space command
submission should not be printed to dmesg by default. So add a new
preprocessor define called VMW_DEBUG_USER which translates to
DRM_DEBUG_DRIVER.
v2: Use VMW_DEBUG_USER instead of using DRM_DEBUG_DRIVER directly.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Use preprocessor macro for repetitive device command struct format.
v2: Name-space distinction for preprocessor macro.
v3: Struct name as macro parameter and rebase.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
