summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2011-05-20[media] drxd: provide ability to control rs byteDevin Heitmueller
Provide the ability for the board configuration to specify whether to insert the RS byte into the TS interconnect to the bridge, while not required for the ngene in fact is required for the em28xx. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-20[media] drxd: add driver to Makefile and KconfigDevin Heitmueller
Add the drxd to the Makefile and Kconfig Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-20drx: add initial drx-d driverRalph Metzler
These are the original drx-d sources, extracted from Ralph Metzler's GPL'd ngene driver. No modifications/cleanup have yet been made. In fact, no measures have been taken to see if the code even compiles. Signed-off-by Ralph Metzler <rjkm@metzlerbros.de> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-20[media] mantis: trivial module parameter documentation fixBjørn Mork
The default for "verbose" is 0. Update description to match. Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-20[media] use pci_dev->revisionBjørn Mork
pci_setup_device() has saved the PCI revision in the pci_dev struct since Linux 2.6.23. Use it. Cc: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-20[media] xc5000: Improve it to work better with 6MHz-spaced channelsMauro Carvalho Chehab
Brazil uses 6MHz-spaced channels. So, the nyquist filter for DVB-C should be different, otherwise, inter-channel interference may badly affect the device, and signal may not be properly decoded. On my tests here, without this patch, sometimes channels are seen, but, most of the time, PID filter returns with timeout. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-20[media] DM04/QQBOX Fix issue with firmware release and cold resetMalcolm Priestley
Fix issue where firmware does not release on cold reset. Also, default firmware never cold resets in multi tuner environment. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-20drm/radeon/kms: fixup eDP connector handlingAlex Deucher
It's more like LVDS then DP in some ways. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: bail early for eDP in hotplug callbackAlex Deucher
Don't try and en/disable the port as it may be a hpd event from powering up/down the panel during a modeset or dpms. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: simplify hotplug handler logicAlex Deucher
In the hotplug handler, just use the drm dpms functions. If the monitor is plugged in, turn it on, if it's not, turn it off. This also reduces power usage by turning off the encoder and crtc when the monitor is unplugged. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: rewrite DP handlingAlex Deucher
- reorganize the functions based on use - clean up function naming - rework link training to better match what we use internally - add initial support for DP 1.2 (no MST yet) Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms/atom: add support for setting DP panel modeAlex Deucher
Required for proper operation with DP bridges. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: atombios.h updates for DP panel modeAlex Deucher
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: handle DP bridgesAlex Deucher
Fusion hardware often has DP to VGA/LVDS/TMDS bridges to handle non-DP encoders. Internally we treat them mostly like DP. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: improve aux error handlingAlex Deucher
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: improve DP detect logicAlex Deucher
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: add some dp encoder/connector helper funcsAlex Deucher
Used for dp1.2 support and for dp bridges. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: make sure eDP panel is on for modesettingAlex Deucher
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: fix eDP panel power functionAlex Deucher
need to wait for the panel to power up. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: adjust eDP handling (v2)Alex Deucher
eDP is usually used as an LVDS replacement, so treat it more like LVDS from the user perspective. v2: encoder mode is always DP for eDP. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: fix up DP clock programming on DCE4/5Alex Deucher
In DP mode, the DP ref clock can come from PPLL, DCPLL, or ext clock, depending on the asic. The crtc virtual pixel clock is derived from the DP ref clock. - DCE4: PPLL or ext clock - DCE5: DCPLL or ext clock Setting ATOM_PPLL_INVALID will cause SetPixelClock to skip PPLL/DCPLL programming and only program the DP DTO for the crtc virtual pixel clock. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: spread spectrum fixesAlex Deucher
- properly mask the ss type - don't enable ss if type is external or percentage is 0 - if ss enabled and type is external, set ref_div_src to ext clock - prefer ASIC_INTERNAL_SS_ON_DP to LCD_Info SS_Id for eDP - fix ss amount calculation Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: properly handle bpc >8 in atom command tablesAlex Deucher
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20drm/radeon/kms: DCE4.1 DIG encoders are fully routeable just like DCE3.2Alex Deucher
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2011-05-20Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6 into ↵Russell King
devel-stable
2011-05-20HID: hiddev: fix race between hiddev_disconnect and hiddev_releaseJiri Kosina
When hiddev_disconnect() runs with chardev open, it will proceed with usbhid_close(). When userspace in parallel runs the hiddev_release(), it sees !hiddev->exists (as it has been already set so by hiddev_disconnect()) and kfrees hiddev while hiddev_disconnect() hasn't finished yet. Serialize the access to hiddev->exists and hiddev->open by existancelock. Reported-by: mike-@cinci.rr.com Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-05-20HID: magicmouse: ignore 'ivalid report id' while switching modesJiri Kosina
The device reponds with 'invalid report id' when feature report switching it into multitouch mode is sent to it. This has been silently ignored before 0825411ade ("HID: bt: Wait for ACK on Sent Reports"), but since this commit, it propagates -EIO from the _raw callback . So let the driver ignore -EIO as response to 0xd7,0x01 report, as that's how the device reacts in normal mode. Sad, but following reality. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=35022 Tested-by: Chase Douglas <chase.douglas@canonical.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-05-20HID: fix a crash in hid_report_raw_event() function.Armando Visconti
I'm using a Data Modul EasyTouch USB multitouch controller, which is issuing a hid report with a size equals to 0. The rsize value gets set to 536870912 and Linux is crashing in the memset because the value is too big. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-05-20spi/amba-pl022: work in polling or interrupt mode if pl022_dma_probe failsViresh Kumar
If pl022_dma_probe fails, we can try to transfer data in polling or interrupt mode. Also, set platform_info->enable_dma to 0, so that no other code tries to use dma. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20spi/spi_s3c24xx: Use spi_bitbang_stop instead of spi_unregister_master in ↵Axel Lin
s3c24xx_spi_remove Calling spi_bitbang_stop() will also destroy bitbang->workqueue, which is created by calling spi_bitbang_start() in s3c24xx_spi_probe(). Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20spi/spi_nuc900: Use spi_bitbang_stop instead of spi_unregister_master in ↵Axel Lin
nuc900_spi_remove Calling spi_bitbang_stop() will also destroy bitbang->workqueue, which is created by calling spi_bitbang_start() in nuc900_spi_probe(). Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20spi/spi_tegra: use spi_unregister_master() instead of spi_master_put()Axel Lin
spi_master_put() should only be used in error handling. Once spi_register_master() returns success, we should call spi_unregister_master() instead. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove pathAxel Lin
spi_master_put() should only be used in error handling. Once spi_register_master() returns success, we should call spi_unregister_master() instead. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20spi: Use void pointers for data in simple SPI I/O operationsMark Brown
Currently the simple SPI I/O operations all take pointers to u8 * buffers to operate on. This creates needless type compatibility issues and the underlying spi_transfer structure uses void pointers anyway so convert the API over to take void pointers too. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20spi/pl022: use cpu_relax in the busy loopLinus Walleij
This relaxes the cpu in the polling busy-wait loop. Reported-by: Vitaly Wool <vitalywool@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20spi/pl022: mark driver non-experimentalLinus Walleij
This driver has no TODO, and is now used on several platforms: ARM, U300, Ux500, SPEAr and more. So drop the EXPERIMENTAL requirement. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20spi/pl022: timeout on polled transfer v2Magnus Templing
This adds the missing handling of polling timeouts and deletes our last todo. Signed-off-by: Magnus Templing <magnus.templing@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> [Fixups from review by Wolfram Sang] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20Merge commit 'v2.6.39' into spi/nextGrant Likely
2011-05-20gpio/via: rename VIA local config structLinus Walleij
The local VIA GPIO config struct "gpio_config" collides with my extension to the gpio_chip struct, so rename it to viafb_gpio_config so we don't get this clash. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20basic_mmio_gpio: split into a gpio library and platform deviceJamie Iles
Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library for implementing GPIO drivers whilst abstracting the register access detail. Based on a patch from Anton Vorontsov[1] and adapted to allow bgpio_chip to be embedded in another structure. Changes since v1: - Register the gpio_chip in the platform device probe 1. https://lkml.org/lkml/2011/4/19/401 Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20gpio: remove some legacy comments in build filesLinus Walleij
The build files for drivers/gpio has some wording and comments about the directory being reserved exclusively for GPIO expanders (according to the gpio.txt file these are on external busses) and this has been false for some time. We already have PL061 and Xilinx drivers which are in silicon and now I'm moving more silicon drivers here, so delete this and reword it a bit. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20gpio: add trace events for setting direction and valueUwe Kleine-König
This patch allows to trace gpio operations using ftrace Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20gpio/pca953x: Use handle_simple_irq instead of handle_edge_irqErik Botö
Make pca953x driver use the simple irq handler since no hardware control is necessary and the driver lacks an irq_ack function. handle_edge_irq() calls chip->irq_ack() which crashes since this function does not exist. Signed-off-by: Erik Botö <erik.boto@pelagicore.com> Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20gpiolib: export gpiochip_findJean Delvare
Export function gpiochip_find so that modules can use it. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20gpio: remove redundant Kconfig depends on GPIOLIBH Hartley Sweeten
Since all the drivers are in a 'if GPIOLIB/endif block', the depends on GPIOLIB is redundant so remove them. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20basic_mmio_gpio: convert to non-__raw* accessorsJamie Iles
The __raw_* accessors don't include memory barriers and can cause problems when writes get stuck in write buffers. Suggested-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20basic_mmio_gpio: support direction registersJamie Iles
Most controllers require the direction of a GPIO to be set by writing to a direction register. Add support for either an input direction register or an output direction register. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20basic_mmio_gpio: support different input/output registersJamie Iles
Some controllers have separate input and output registers. For these controllers, use "set" for the output and "dat" for the input. Changes since v2: reuse "set" for output and "dat" for input rather than adding a new "in" register. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20basic_mmio_gpio: detect output method at probe timeJamie Iles
Rather than detecting the output method each time in the .set() callback, do it at probe time and set the appropriate callback. Changes since v2: moved the reg_dat initialization into bgpio_setup_io(). Signed-off-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20basic_mmio_gpio: request register regionsJamie Iles
Make sure that we get the register regions with request_mem_region() before ioremap() to make sure we have exclusive access. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
generated by cgit (git 2.34.1) at 2025-09-22 15:10:28 +0000