| Age | Commit message (Collapse) | Author |
|---|
|
when skb->encapsulation is 0, skb->ip_summed is CHECKSUM_PARTIAL
and it is udp packet, which has a dest port as the IANA assigned.
the hardware is expected to do the checksum offload, but the
hardware will not do the checksum offload when udp dest port is
4789.
This patch fixes it by doing the checksum in software.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a break missing in the switch/case handling in
hclge_misc_irq_handle, which causes the log to output
uncorrectly.
This patch adds the missing break, and change the dev_dbg
to dev_warn in order to better catch the error.
Fixes: c1a81619d73a ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When resetting, phy_state_machine may be accessing the phy through
firmware if the phy is not stopped or disconnected, which will
cause firemware timeout problem because the firmware is busy
processing the reset request.
This patch fixes it by disabling the phy when resetting.
Fixes: b940aeae0ed6 ("net: hns3: never send command queue message to IMP when reset")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hardware sends the HCLGE_VECTOR0_EVENT_RST event through
hclge_misc_irq_handle, currently driver enables misc_vector in
the interrupt handle, and hardware generates the same interrupt
for the same reset event again and again until the reset is
complete, which causes hclge_reset running repeatly problem.
This patch fixes by enabling the misc_vector after reset is
complete.
Fixes: 4ed340ab8f49 ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hclge_ae_stop is called during resetting, it will cancel the
service_task by calling cancel_work_sync, which may cause the
service_task to exit without clearing HCLGE_STATE_SERVICE_SCHED
bit. If this happens, the service_task will never run again.
This patch fixes this problem by clearing it after calling
cancel_work_sync in hclge_ae_stop.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing function reset or insmod hns3 dirver after rmmod,
the entries of mac vlan table are not cleared, which may cause
init mac address failed. This patch fixes it by clearing the
old mac address when doing function reset or rmmod hns3 driver.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add checking for new mac address. It doesn't need to config
the mac vlan table if it's already in use.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for IFF_ALLMULTI flag to HNS3 PF and VF
driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is only 128 entries for hardware's vf vlan table, when
the vf table is full, the firmware will disable the vf vlan
filter and return a resp_code of HCLGE_VF_VLAN_NO_ENTRY to
driver.
This patch checks the if resp_code from firmware is
HCLGE_VF_VLAN_NO_ENTRY, if yes, then print a warning and
return ok to the caller.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The log entry dentries are only set, never referenced, so no need to
keep them around. Remove the pointer from struct
vchiq_debugfs_log_entry as it is not needed anymore and get rid of the
separate vchiq_debugfs_create_log_entries() function as it is only used
in one place.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no need to set this to be int * when it is only used as a void *.
This lets us remove the unneeded cast, and unneeded temporary variable
the one place it is referenced in the code.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This structure, and the one static variable that was declared with it,
were not being used for anything. The log_categories field was being
set, but never used again. So just remove it entirely as it is not
needed at all.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This does not need to be part of a wrapper function, or in a structure,
just properly reference it directly as a single variable.
The whole variable will be going away soon anyway, this is just a step
toward that direction.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vchiq_debugfs_top() is only a wrapper around a pointer to a dentry, so
just use the dentry directly instead, making it a static variable
instead of part of a static structure.
This also removes the pointless BUG_ON() when checking that dentry as no
one should ever care if debugfs is working or not, and the kernel should
really not panic over something as trivial as that.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Clean up the vchiq_arm code by not caring about the value of debugfs
calls. This ends up removing a number of lines of code that are not
needed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no bus infrastructure today to handle all the mmagic bus
clocks and GDSCs needed by all the multimedia blocks in msm8996, like
mdss, video, camera and gpu. Mark all these clocks with a CLK_IS_CRITICAL
and GDSCs with a ALWAYS_ON flag for now so they are left always enabled.
This patch should be reverted at some point when we do have a bus driver
to manage these clocks and GDSCs.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
We have atleast some instances of ALWAYS_ON gdscs, which need to
be turned ON *before* some clocks within the gdsc domain marked
with a CLK_IS_CRITICAL can be turned ON.
To facilitate this sequence, register the GDCSs (and hence handle
the ALWAYS_ON gdscs) before we register clocks (and handle the
clocks marked as CLK_IS_CRITICAL)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Some GDSCs might have software control to turn them off, but we might
want to keep them enabled always, in some cases because of lack of
support in kernel to handle a graceful turning off/on of such GDSCs.
Most common instances would be the GDCSs which power up the noc/bus
fabrics, which need bus drivers to handle them and atleast support for
which is missing on all qcom SoCs.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Testing Telit LM940 with ICMP packets > 14552 bytes revealed that
the modem needs FLAG_SEND_ZLP to properly work, otherwise the cdc
mbim data interface won't be anymore responsive.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add LED platform driver activation from mlx-platform. This LED driver uses
the same regmap infrastructure as others Mellanox platform drivers, so LED
specific registers description is added.
System LED configuration depends on system type. To support all the
relevant types per system type LED descriptions are defined for passing
to LED platform driver.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Add new ODM system types, matched according to DMI_BOARD_NAME. The
supported ODM Ids are: VMOD0001, VMOD0002, VMOD0003, VMOD0004, VMOD0005.
Patch does not introduce new systems, but allows to ODM companies to set
DMI_BOARD_VENDOR and DMI_PRODUCT_NAME on their own. It assumes that ODM
company can't change DMI_BOARD_NAME.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Add extra cycle for hotplug work queue to handle the case when a signal is
It adds missed logic for signal acknowledge, by adding an extra run for
received, but no specific signal assertion is detected. Such case
theoretically can happen for example in case several units are removed or
inserted at the same time. In this situation acknowledge for some signal
can be missed at signal top aggreagation status level. The extra run will
allow to handler to acknowledge the missed signal.
The interrupt handling flow performs the next steps:
(1)
Enter mlxreg_hotplug_work_handler due to signal assertion.
Aggregation status register is changed for example from 0xff to 0xfd
(event signal group related to bit 1).
(2)
Mask aggregation interrupts, read aggregation status register and save it
(0xfd) in aggr_cache, then traverse down to handle signal from groups
related to the changed bit.
(3)
Read and mask group related signal.
Acknowledge and unmask group related signal (acknowledge should clear
aggregation status register from 0xfd back to 0xff).
(4)
Re-schedule work queue for the immediate execution.
(5)
Enter mlxreg_hotplug_work_handler due to re-scheduling.
Aggregation status is changed from previous 0xfd to 0xff.
Go over steps (2) - (5) and in case no new signal assertion
is detected - unmask aggregation interrupts.
The possible race could happen in case new signal from the same group is
asserted after step (3) and prior step (5). In such case aggregation
status will change back from 0xff to 0xfd and the value read from the
aggregation status register will be the same as a value saved in
aggr_cache. As a result the handler will not traverse down and signal
will stay unhandled.
Example of faulty flow:
The signal routing flow is as following (f.e. for of FANi removing):
- FAN status and event registers related bit is changed;
-- intermediate aggregation status register is changed;
--- top aggregation status register is changed;
---- interrupt routed to CPU and interrupt handler is invoked.
When interrupt handler is invoked it follows the next simple logic (f.e
FAN3 is removed):
(a1) mask top aggregation interrupt mask register;
(a2) read top aggregation interrupt status register and test to which
underling group belongs a signal (FANs in this case and is changed
from 0xff to 0xfb and 0xfb is saved as a last status value);
(b1) mask FANs interrupt mask register;
(b2) read FANs status register and test which FAN has been changed
FAN3 in this example);
(c1) perform relevant action;
<--------------- (FAN2 is removed at this point)
(b3) clear FANs interrupt event register to acknowledge FAN3 signal;
(b4) unmask FANs interrupt mask register
(a3) unmask top aggregation interrupt mask register;
An interrupt handler is invoked, since FAN2 interrupt is not acknowledge.
It should set top aggregation interrupt status register bit 6 (0xfb).
In step (a2)
(a2) read top aggregation interrupt and comparing it with saved value
does not show change (same 0xfb) and after (a2) execution jumps to
(a3) and signal leaved unhandled
The fix will enforce handler to traverse down in case the signal is
received, but signal assertion is not detected.
Fixes: 304887041d95 ("platform/x86: Introduce support for Mellanox hotplug driver")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Use devm_* variants of kstrdup and kzalloc. Get rid of kfree cleanups.
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Make the asus_atk0110 driver use hwmon_device_register_with_groups instead
of the deprecated hwmon_device_register.
Construct the expected attribute_group array from the sensor list which
contains all needed attributes.
Remove the manual sysfs file creation and deletion that are now taken care
of by the (un)register calls via the attribute_group array.
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function get_raw_temp is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warning:
drivers/hwmon/k10temp.c:149:14: warning: symbol 'get_raw_temp' was not
declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
APC virtual machines arent used on POWER-9 chips and are already
disabled in on-chip CAPP. They also need to be disabled on the PSL via
'PSL Data Send Control Register' by setting bit(47). This forces the
PSL to send commands to CAPP with queue.id == 0.
Fixes: 5632874311db ("cxl: Add support for POWER9 DD2")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently we see a kernel-oops reported on Power-9 while attaching a
context to an AFU, with radix-mode and sysfs attr 'prefault_mode' set
to anything other than 'none'. The backtrace of the oops is of this
form:
Unable to handle kernel paging request for data at address 0x00000080
Faulting instruction address: 0xc00800000bcf3b20
cpu 0x1: Vector: 300 (Data Access) at [c00000037f003800]
pc: c00800000bcf3b20: cxl_load_segment+0x178/0x290 [cxl]
lr: c00800000bcf39f0: cxl_load_segment+0x48/0x290 [cxl]
sp: c00000037f003a80
msr: 9000000000009033
dar: 80
dsisr: 40000000
current = 0xc00000037f280000
paca = 0xc0000003ffffe600 softe: 3 irq_happened: 0x01
pid = 3529, comm = afp_no_int
<snip>
cxl_prefault+0xfc/0x248 [cxl]
process_element_entry_psl9+0xd8/0x1a0 [cxl]
cxl_attach_dedicated_process_psl9+0x44/0x130 [cxl]
native_attach_process+0xc0/0x130 [cxl]
afu_ioctl+0x3f4/0x5e0 [cxl]
do_vfs_ioctl+0xdc/0x890
ksys_ioctl+0x68/0xf0
sys_ioctl+0x40/0xa0
system_call+0x58/0x6c
The issue is caused as on Power-8 the AFU attr 'prefault_mode' was
used to improve initial storage fault performance by prefaulting
process segments. However on Power-9 with radix mode we don't have
Storage-Segments that we can prefault. Also prefaulting process Pages
will be too costly and fine-grained.
Hence, since the prefaulting mechanism doesn't makes sense of
radix-mode, this patch updates prefault_mode_store() to not allow any
other value apart from CXL_PREFAULT_NONE when radix mode is enabled.
Fixes: f24be42aab37 ("cxl: Add psl9 specific code")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
As the mvpp2 driver is growing, move this driver to a dedicated
directory and split it into several files.
Since this driver has a lot of register defines and structure
definitions, it can benefit from having all of this into a dedicated
header file, named mvpp2.h.
A good chunk of the mvpp2 code is dedicated to Header Parser handling, so
we introduce mvpp2_prs.h where all Header Parser definitions are located,
and mvpp2_prs.c containing the related code.
In the same way, mvpp2_cls.h and mvpp2_cls.c are created to contain
Classifier and RSS related code.
The former 'mvpp2.c' file is renamed 'mvpp2_main.c' so that we can keep
the driver binary named 'mvpp2'.
This commit is only about spliting the driver into multiple files and
doesn't introduce any new function, feature or fix besides removing
'static' keywords when needed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to check return value of zap_vma_ptes()
because there is nothing to do with this knowledge.
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The failure reported by zap_vma_ptes() means that wrong VMA pages
were supplied, however it is impossible for this type of address.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to check return value of zap_vma_ptes()
because there is nothing to do with this knowledge.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Let's perform checks in-place instead of BUG_ONs.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to check existence of mad_queue, because we already did
pointer dereference before call to dequeue_mad().
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to bring down the whole machine, just because unknown
event was received. It is better to ignore it silently.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In case CM work list is empty, the work pointer will be NULL,
so instead of kernel crash it is better to abort processing
of works.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
cxgb3 driver properly handles errors returned by IDR, so there is no
need to have special case (kernel crash) just because IDR is full.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to crash the machine if unknown work request was
received in SQP MAD.
Cc: <stable@vger.kernel.org> # 3.6
Fixes: 37bfc7c1e83f ("IB/mlx4: SR-IOV multiplex and demultiplex MADs")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Any steering QP is supposed be above steering_qp_base,
see function mlx4_ib_steer_qp_alloc() for it, however in case
of misalignment between SW and FW, this qp_base can be wrong.
Use WARN() to catch such situation without killing the machine.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds support for the BCM5389 switch connected through MDIO.
Signed-off-by: Damien Thébault <damien.thebault@vitec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pblk allocates line bitmaps within the line lock unnecessarily. In order
to take pressure out of the fast patch, allocate line bitmaps outside
of this lock and refactor accordingly.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Unless we kick the writer directly when setting a new flush point, the
user risks having to wait for up to one second (the default timeout for
the write thread to be kicked) for the IO to complete.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When switching between different lun configurations, there is no
guarantee that all lines that contain closed/open chunks have some
valid data to recover.
Check that the smeta chunk has been written to instead. Also
skip bad lines (that does not have enough good chunks).
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In the read path, pblk gets a reference to the incoming bio and puts it
after ending the bio. Though this behavior is correct, it is unnecessary
since pblk is the one putting the bio, therefore, it cannot disappear
underneath it.
Removing this reference, allows to clean up rqd->bio and avoids pointer
bouncing for the different read paths. Now, the incoming bio always
resides in the read context and pblk's internal bios (if any) reside in
rqd->bio.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In some cases, users can want set write buffer size manually, e.g. to
adjust it to specific workload. This patch provides the possibility
to set write buffer size via module parameter feature.
Signed-off-by: Marcin Dziegielewski <marcin.dziegielewski@intel.com>
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When error occurs during bio_add_page on partial read path, pblk
tries to free pages twice.
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Marcin Dziegielewski <marcin.dziegielewski@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently in case of error caused by bio_pc_add_page in
pblk_bio_add_pages two issues occur when calling from
pblk_rb_read_to_bio(). First one is in pblk_bio_free_pages, since we
are trying to free pages not allocated from our mempool. Second one
is the warn from dma_pool_free, that we are trying to free NULL
pointer dma.
This commit fix both issues.
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Marcin Dziegielewski <marcin.dziegielewski@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Smeta write errors were previously ignored. Skip these
lines instead and throw them back on the free
list, so the chunks will go through a reset cycle
before we attempt to use the line again.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Write failures should not happen under normal circumstances,
so in order to bring the chunk back into a known state as soon
as possible, evacuate all the valid data out of the line and let the
fw judge if the block can be written to in the next reset cycle.
Do this by introducing a new gc list for lines with failed writes,
and ensure that the rate limiter allocates a small portion of
the write bandwidth to get the job done.
The lba list is saved in memory for use during gc as we
cannot gurantee that the emeta data is readable if a write
error occurred.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The write error recovery path is incomplete, so rework
the write error recovery handling to do resubmits directly
from the write buffer.
When a write error occurs, the remaining sectors in the chunk are
mapped out and invalidated and the request inserted in a resubmit list.
The writer thread checks if there are any requests to resubmit,
scans and invalidates any lbas that have been overwritten by later
writes and resubmits the failed entries.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
