| Age | Commit message (Collapse) | Author |
|---|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 9efc9b2b04c7 ("net: stmmac: Add dwmac-intel-plat for GBE driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605249243-17262-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3ced0a88cd4c ("qlcnic: Add support to run firmware POST")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605248186-16013-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: ca139d76b0d9 ("cx82310_eth: re-enable ethernet mode after router reboot")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605247627-15385-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed
to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek,
ksz9031, dp83867, ...) now configure the internal delay based on that
when they used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution
that would avoid breaking all boards, but that does not seem to be
happening any time soon, so I am now sending the correct version of
the dts files to ensure that at least these machines can use their
network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU operating
points to match the data sheet
- A revert for a dts patch that caused a regression in USB support on
Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak and
missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent for
correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems"
* tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid"
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
arm64: dts: agilex/stratix10: Fix qspi node compatible
ARM: dts: imx6q-prti6q: fix PHY address
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
...
|
|
If intel context create failed, the perf_request_latency() will return 0
rather than error, because we doesn't initialize the return value.
Fixes: 25c26f18ea79 ("drm/i915/selftests: Measure dispatch latency")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116143540.3648870-1-zhangxiaoxu5@huawei.com
(cherry picked from commit 19384452052a1e0525e663bfbdd62ac1399bb647)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
If intel context create failed, the perf_series_engines() will return 0
rather than error, because we doesn't initialize the return value.
Fixes: cbfd3a0c5a55 ("drm/i915/selftests: Add request throughput measurement to perf")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116144112.3673011-1-zhangxiaoxu5@huawei.com
(cherry picked from commit 01d708840c26c9532579677eaca942363a009fd5)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
I forgot to free the old list when growing past 16 entries.
Luckily, as much as I checked, none of the current platforms has more than
16 workarounds on a single list.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 452420d22d5b ("drm/i915: Fuse per-context workaround handling with the common framework")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201113132510.2298483-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 77c296966e866a795742a46fc52a218771894867)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Some media power gates are disabled by default. commit 5d86923060fc
("drm/i915/tgl: Enable VD HCP/MFX sub-pipe power gating")
tried to enable it, but it duplicated an existent register.
So, the main PG setup sequences ended up overwriting it.
So, let's now merge this to the main PG setup sequence.
v2: (Chris): s/BIT/REG_BIT, remove useless comment,
remove useless =0, use the right gt,
remove rc6 sequence doubt from commit message.
Fixes: 5d86923060fc ("drm/i915/tgl: Enable VD HCP/MFX sub-pipe power gating")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: stable@vger.kernel.org#v5.5+
Cc: Dale B Stimson <dale.b.stimson@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201111072859.1186070-1-rodrigo.vivi@intel.com
(cherry picked from commit 695dc55b573985569259e18f8e6261a77924342b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V fix from Wei Liu:
"One patch from Chris to fix kexec on Hyper-V"
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: vmbus: Allow cleanup of VMBUS_CONNECT_CPU if disconnected
|
|
Pull vhost fixes from Michael Tsirkin:
"Fixes all over the place, most notably vhost scsi IO error fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost scsi: Add support for LUN resets.
vhost scsi: add lun parser helper
vhost scsi: fix cmd completion race
vhost scsi: alloc cmds per vq instead of session
vhost: add helper to check if a vq has been setup
vdpasim: fix "mac_pton" undefined error
swiotlb: using SIZE_MAX needs limits.h included
|
|
This has been stable for a while.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A user reports (slightly shortened from the original message):
libphy: lantiq,xrx200-mdio: probed
mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing.
gswip 1e108000.switch lan: no phy at 2
gswip 1e108000.switch lan: failed to connect to port 2: -19
lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy
This is a single-port board using the internal Fast Ethernet PHY. The
user reports that switching to PHY scanning instead of configuring the
PHY within device-tree works around this issue.
The documentation for the standalone variant of the PHY11G (which is
probably very similar to what is used inside the xRX200 SoCs but having
the firmware burnt onto that standalone chip in the factory) states that
the PHY needs 300ms to be ready for MDIO communication after releasing
the reset.
Add a 300ms delay after initializing all GPHYs to ensure that the GPHY
firmware had enough time to initialize and to appear on the MDIO bus.
Unfortunately there is no (known) documentation on what the minimum time
to wait after releasing the reset on an internal PHY so play safe and
take the one for the external variant. Only wait after the last GPHY
firmware is loaded to not slow down the initialization too much (
xRX200 has two GPHYs but newer SoCs have at least three GPHYs).
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return the error code from
devm_reset_control_get_optional_exclusive() instaed of 0
in cqspi_probe().
Fixes: 31fb632b5d43ca ("spi: Move cadence-quadspi driver to drivers/spi/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20201116141836.2970579-1-chengzhihao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If we have more than 4 displays we will run
into dummy irq calls or flip timout issues.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
From commit 6915564dc5a8 ("ACPI: OSL: Change the type of
acpi_os_map_generic_address() return value"),
acpi_os_map_generic_address() will return logical address or NULL
for error, but for ACPI_ADR_SPACE_SYSTEM_IO case, it should be also
return 0 as it's a normal case, but now it will return -ENXIO.
So check it out for such case to avoid einj module initialization
fail.
Fixes: 6915564dc5a8 ("ACPI: OSL: Change the type of acpi_os_map_generic_address() return value")
Cc: <stable@vger.kernel.org>
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aili Yao <yaoaili@kingsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After initial kernel module load during kernel boot and removing
the module and try to load it again an Unable to handle kernel
paging request is observed:
Unable to handle kernel paging request at virtual address ffffa44f7416eae0
Mem abort info:
ESR = 0x96000047
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000047
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000008147c000
[ffffa44f7416eae0] pgd=000000017df9f003, p4d=000000017df9f003,
pud=000000017df9e003, pmd=000000017df9b003, pte=0000000000000000
Internal error: Oops: 96000047 [#1] PREEMPT SMP
Modules linked in: venus_core(+) snd_soc_wsa881x regmap_sdw af_alg
snd_soc_wcd934x soundwire_qcom gpio_wcd934x q6asm_dai q6routing
q6adm q6afe_dai snd_soc_hdmi_codec q6afe q6asm q6dsp_common q6cor
display_connector rmtfs_mem drm ip_tables x_tables ipv6
[last unloaded: venus_core]
CPU: 6 PID: 889 Comm: modprobe Tainted: G W 5.10.0-rc1+ #8
Hardware name: Thundercomm Dragonboard 845c (DT)
pstate: 80400085 (Nzcv daIf +PAN -UAO -TCO BTYPE=--)
pc : queued_spin_lock_slowpath+0x1dc/0x3c8
lr : do_raw_spin_lock+0xc0/0x118
sp : ffff8000142cb7b0
x29: ffff8000142cb7b0 x28: 0000000000000013
x27: ffffa44f72de5690 x26: 0000000000000003
x25: ffff17c2d00f8080 x24: ffff17c2c0d78010
x23: ffff17c2c0d4f700 x22: ffff17c2d00f8080
x21: 0000000000000000 x20: ffffa44f74148000
x19: ffff17c2c0d4f8f8 x18: 0000000000000000
x17: 0000000000000000 x16: ffffa44f7342f158
x15: 0000000000000040 x14: ffffa44f746e8320
x13: 0000000000000228 x12: 0000000000000020
x11: 0000000000000000 x10: 00000000001c0000
x9 : 0000000000000000 x8 : ffff17c33d746ac0
x7 : ffff17c2c109b000 x6 : ffffa44f7416eac0
x5 : ffff17c33d746ac0 x4 : 0000000000000000
x3 : ffff17c2c0d4f8f8 x2 : ffffa44f7416eae0
x1 : ffffa44f7416eae0 x0 : ffff17c33d746ac8
Call trace:
queued_spin_lock_slowpath+0x1dc/0x3c8
do_raw_spin_lock+0xc0/0x118
_raw_spin_lock_irqsave+0x80/0x14c
__pm_runtime_resume+0x38/0xb8
device_link_add+0x3b8/0x5d0
core_get_v4+0x268/0x2d8 [venus_core]
venus_probe+0x108/0x458 [venus_core]
platform_drv_probe+0x54/0xa8
really_probe+0xe4/0x3b0
driver_probe_device+0x58/0xb8
device_driver_attach+0x74/0x80
__driver_attach+0x58/0xe8
bus_for_each_dev+0x70/0xc0
driver_attach+0x24/0x30
bus_add_driver+0x150/0x1f8
driver_register+0x64/0x120
__platform_driver_register+0x48/0x58
qcom_venus_driver_init+0x20/0x1000 [venus_core]
do_one_initcall+0x84/0x458
do_init_module+0x58/0x208
load_module+0x1ec0/0x26a8
__do_sys_finit_module+0xb8/0xf8
__arm64_sys_finit_module+0x20/0x30
el0_svc_common.constprop.0+0x7c/0x1c0
do_el0_svc+0x24/0x90
el0_sync_handler+0x180/0x188
el0_sync+0x174/0x180
Code: 91002100 8b0200c2 f861d884 aa0203e1 (f8246828)
---[ end trace f1f687c15fd6b2ca ]---
note: modprobe[889] exited with preempt_count 1
After revisit the OPP part of the code I found that OPP pmdomain
is detached with direct call to dev_pm_domain_detach instead of
OPP wraper for detaching pmdomains with OPP table. Correct this
by calling the OPP dev_pm_opp_detach_genpd.
Fixes: 9a538b83612c ('media: venus: core: Add support for opp tables/perf voting')
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The profile and level in op_set_ctrl was recently changed but during
v4l2_ctrl_handler_setup profile and level control values are mangled.
Fixes: 435c53c3698f ("media: venus: venc: Use helper to set profile and level")
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f8d0 ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Actually, burst size is equal to '1 << desc->rqcfg.brst_size'.
we should use burst size, not desc->rqcfg.brst_size.
dma memcpy performance on Rockchip RV1126
@ 1512MHz A7, 1056MHz LPDDR3, 200MHz DMA:
dmatest:
/# echo dma0chan0 > /sys/module/dmatest/parameters/channel
/# echo 4194304 > /sys/module/dmatest/parameters/test_buf_size
/# echo 8 > /sys/module/dmatest/parameters/iterations
/# echo y > /sys/module/dmatest/parameters/norandom
/# echo y > /sys/module/dmatest/parameters/verbose
/# echo 1 > /sys/module/dmatest/parameters/run
dmatest: dma0chan0-copy0: result #1: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #2: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #3: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #4: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #5: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #6: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #7: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #8: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
Before:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 48 iops 200338 KB/s (0)
After this patch:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 179 iops 734873 KB/s (0)
After this patch and increase dma clk to 400MHz:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 259 iops 1062929 KB/s (0)
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Link: https://lore.kernel.org/r/1605326106-55681-1-git-send-email-sugar.zhang@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit 7f832645d0e5 ("dmaengine: ioatdma: remove ioatdma v2 registration")
missed to remove dca2_tag_map_valid() during its removal. Hence, since
then, dca2_tag_map_valid() is unused and make CC=clang W=1 warns:
drivers/dma/ioat/dca.c:44:19:
warning: unused function 'dca2_tag_map_valid' [-Wunused-function]
So, remove this unused function and get rid of a -Wused-function warning.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113081248.26416-1-lukas.bulwahn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Portal size is 4k. Current code is mapping all 4 portals in a single chunk.
Restrict the mapped portal size to a single portal to ensure that submission
only goes to the intended portal address.
Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160513342642.510187.16450549281618747065.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-11-15
Anant Thazhemadam contributed two patches for the AF_CAN that prevent potential
access of uninitialized member in can_rcv() and canfd_rcv().
The next patch is by Alejandro Concepcion Rodriguez and changes can_restart()
to use the correct function to push a skb into the networking stack from
process context.
Zhang Qilong's patch fixes a memory leak in the error path of the ti_hecc's
probe function.
A patch by me fixes mcba_usb_start_xmit() function in the mcba_usb driver, to
first fill the skb and then pass it to can_put_echo_skb().
Colin Ian King's patch fixes a potential integer overflow on shift in the
peak_usb driver.
The next two patches target the flexcan driver, a patch by me adds the missing
"req_bit" to the stop mode property comment (which was broken during net-next
for v5.10). Zhang Qilong's patch fixes the failure handling of
pm_runtime_get_sync().
The next seven patches target the m_can driver including the tcan4x5x spi
driver glue code. Enric Balletbo i Serra's patch for the tcan4x5x Kconfig fix
the REGMAP_SPI dependency handling. A patch by me for the tcan4x5x driver's
probe() function adds missing error handling to for devm_regmap_init(), and in
tcan4x5x_can_remove() the order of deregistration is fixed. Wu Bo's patch for
the m_can driver fixes the state change handling in
m_can_handle_state_change(). Two patches by Dan Murphy first introduce
m_can_class_free_dev() and then make use of it to fix the freeing of the can
device. A patch by Faiz Abbas add a missing shutdown of the CAN controller in
the m_can_stop() function.
* tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: m_can_stop(): set device to software init mode before closing
can: m_can: Fix freeing of can device from peripherials
can: m_can: m_can_class_free_dev(): introduce new function
can: m_can: m_can_handle_state_change(): fix state change
can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration
can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init()
can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI
can: flexcan: fix failure handling of pm_runtime_get_sync()
can: flexcan: flexcan_setup_stop_mode(): add missing "req_bit" to stop mode property comment
can: peak_usb: fix potential integer overflow on shift of a int
can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb()
can: ti_hecc: Fix memleak in ti_hecc_probe
can: dev: can_restart(): post buffer from the right context
can: af_can: prevent potential access of uninitialized member in canfd_rcv()
can: af_can: prevent potential access of uninitialized member in can_rcv()
====================
Link: https://lore.kernel.org/r/20201115174131.2089251-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd3430d ("s390/dasd: fix handling of internal requests")
Cc: <stable@vger.kernel.org> #4.16
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The following warning is reported if lock debugging is enabled.
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 1 PID: 1 at kernel/locking/lockdep.c:4617 lockdep_init_map_waits+0x141/0x222
...
Call Trace:
__kernfs_create_file+0x7a/0xd8
sysfs_add_file_mode_ns+0x135/0x189
sysfs_create_file_ns+0x70/0xa0
acpi_fan_probe+0x547/0x621
platform_drv_probe+0x67/0x8b
...
Dynamically allocated sysfs attributes need to be initialized to avoid
the warning.
Fixes: d19e470b6605 ("ACPI: fan: Expose fan performance state information")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Annotate tegra_pm_set[clear]_cpu_in_lp2() with RCU_NONIDLE in order to
fix lockdep warning about suspicious RCU usage of a spinlock during late
idling phase.
WARNING: suspicious RCU usage
...
include/trace/events/lock.h:13 suspicious rcu_dereference_check() usage!
...
(dump_stack) from (lock_acquire)
(lock_acquire) from (_raw_spin_lock)
(_raw_spin_lock) from (tegra_pm_set_cpu_in_lp2)
(tegra_pm_set_cpu_in_lp2) from (tegra_cpuidle_enter)
(tegra_cpuidle_enter) from (cpuidle_enter_state)
(cpuidle_enter_state) from (cpuidle_enter_state_coupled)
(cpuidle_enter_state_coupled) from (cpuidle_enter)
(cpuidle_enter) from (do_idle)
...
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reported-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix build errors when CONFIG_TYPEC_QCOM_PMIC=y and
CONFIG_USB_ROLE_SWITCH=m by limiting the former to =m when
USB_ROLE_SWITCH also =m.
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_remove':
qcom-pmic-typec.c:(.text+0x28): undefined reference to `.usb_role_switch_set_role'
powerpc64-linux-ld: qcom-pmic-typec.c:(.text+0x64): undefined reference to `.usb_role_switch_put'
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_check_connection':
qcom-pmic-typec.c:(.text+0x120): undefined reference to `.usb_role_switch_set_role'
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_probe':
qcom-pmic-typec.c:(.text+0x360): undefined reference to `.fwnode_usb_role_switch_get'
powerpc64-linux-ld: qcom-pmic-typec.c:(.text+0x4e4): undefined reference to `.usb_role_switch_put'
Fixes: 6c8cf3695176 ("usb: typec: Add QCOM PMIC typec detection driver")
Cc: linux-usb@vger.kernel.org
Cc: Wesley Cheng <wcheng@codeaurora.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20201116040653.7943-1-rdunlap@infradead.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Two bugs for Cadence USB3 gadget driver
- TD_SIZE entry at descriptor is error for multiple-trb use case
- Possible use uninitialized variables
* tag 'usb-fixes-v5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdns3: gadget: calculate TD_SIZE based on TD
usb: cdns3: gadget: initialize link_trb as NULL
|
|
There is a spelling mistake in the Kconfig. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201114120518.416120-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This Kconfig entry should declare a dependency on OF
Fixes: 67b27dbeac4d ("phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20201113151225.1657600-3-bryan.odonoghue@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This Kconfig entry should declare a dependency on OF
Fixes: 6076967a500c ("phy: qualcomm: usb: Add SuperSpeed PHY driver")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lkml.org/lkml/2020/11/13/414
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20201113151225.1657600-2-bryan.odonoghue@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The Intel Keem Bay eMMC PHY is only present on Intel Keem Bay SoCs.
Hence add a dependency on ARCH_KEEMBAY, to prevent asking the user about
this driver when configuring a kernel without Intel Keem Bay platform
support.
Fixes: 885c4f4d6cf448f6 ("phy: intel: Add Keem Bay eMMC PHY support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201110144600.3279752-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The TRB entry TD_SIZE is the packet number for the TD (request) but not the
each TRB, so it only needs to be assigned for the first TRB during the TD,
and the value of it is for TD too.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
There is an uninitialized variable "link_trb" usage at function cdns3_ep_run_transfer.
Fixed it by initialize "link_trb" as NULL.
Fixes: 4e218882eb5a ("usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
In newer versions of virtio-scsi we just reset the timer when an a
command times out, so TMFs are never sent for the cmd time out case.
However, in older kernels and for the TMF inject cases, we can still get
resets and we end up just failing immediately so the guest might see the
device get offlined and IO errors.
For the older kernel cases, we want the same end result as the
modern virtio-scsi driver where we let the lower levels fire their error
handling and handle the problem. And at the upper levels we want to
wait. This patch ties the LUN reset handling into the LIO TMF code which
will just wait for outstanding commands to complete like we are doing in
the modern virtio-scsi case.
Note: I did not handle the ABORT case to keep this simple. For ABORTs
LIO just waits on the cmd like how it does for the RESET case. If
an ABORT fails, the guest OS ends up escalating to LUN RESET, so in
the end we get the same behavior where we wait on the outstanding
cmds.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/1604986403-4931-6-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Move code to parse lun from req's lun_buf to helper, so tmf code
can use it in the next patch.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/1604986403-4931-5-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
We might not do the final se_cmd put from vhost_scsi_complete_cmd_work.
When the last put happens a little later then we could race where
vhost_scsi_complete_cmd_work does vhost_signal, the guest runs and sends
more IO, and vhost_scsi_handle_vq runs but does not find any free cmds.
This patch has us delay completing the cmd until the last lio core ref
is dropped. We then know that once we signal to the guest that the cmd
is completed that if it queues a new command it will find a free cmd.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Link: https://lore.kernel.org/r/1604986403-4931-4-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
We currently are limited to 256 cmds per session. This leads to problems
where if the user has increased virtqueue_size to more than 2 or
cmd_per_lun to more than 256 vhost_scsi_get_tag can fail and the guest
will get IO errors.
This patch moves the cmd allocation to per vq so we can easily match
whatever the user has specified for num_queues and
virtqueue_size/cmd_per_lun. It also makes it easier to control how much
memory we preallocate. For cases, where perf is not as important and
we can use the current defaults (1 vq and 128 cmds per vq) memory use
from preallocate cmds is cut in half. For cases, where we are willing
to use more memory for higher perf, cmd mem use will now increase as
the num queues and queue depth increases.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/1604986403-4931-3-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
This adds a helper check if a vq has been setup. The next patches
will use this when we move the vhost scsi cmd preallocation from per
session to per vq. In the per vq case, we only want to allocate cmds
for vqs that have actually been setup and not for all the possible
vqs.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/1604986403-4931-2-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
ERROR: modpost: "mac_pton" [drivers/vdpa/vdpa_sim/vdpa_sim.ko] undefined!
mac_pton() is defined in lib/net_utils.c and is not built if NET is not set.
Select GENERIC_NET_UTILS as vdpasim doesn't depend on NET.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: https://lore.kernel.org/r/20201113155706.599434-1-lvivier@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
|
|
Pull drm fixes from Dave Airlie:
"Nouveau fixes:
- atomic modesetting regression fix
- ttm pre-nv50 fix
- connector NULL ptr deref fix"
* tag 'drm-fixes-2020-11-16' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/kms/nv50-: Use atomic encoder callbacks everywhere
drm/nouveau/ttm: avoid using nouveau_drm.ttm.type_vram prior to nv50
drm/nouveau/kms: Fix NULL pointer dereference in nouveau_connector_detect_depth
|
|
- atomic modesetting regression fix
- ttm pre-nv50 fix
- connector NULL ptr deref fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv5D9p78MNN0OxVeRZxN8LDqcadJEGUEFCgWJQ6+_rjPuw@mail.gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc/whatever driver fixes for 5.10-rc4.
Nothing huge, lots of small fixes for reported issues:
- habanalabs driver fixes
- speakup driver fixes
- uio driver fixes
- virtio driver fix
- other tiny driver fixes
Full details are in the shortlog.
All of these have been in linux-next for a full week with no reported
issues"
* tag 'char-misc-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
uio: Fix use-after-free in uio_unregister_device()
firmware: xilinx: fix out-of-bounds access
nitro_enclaves: Fixup type and simplify logic of the poll mask setup
speakup ttyio: Do not schedule() in ttyio_in_nowait
speakup: Fix clearing selection in safe context
speakup: Fix var_id_t values and thus keymap
virtio: virtio_console: fix DMA memory allocation for rproc serial
habanalabs/gaudi: mask WDT error in QMAN
habanalabs/gaudi: move coresight mmu config
habanalabs: fix kernel pointer type
mei: protect mei_cl_mtu from null dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt fixes from Greg KH:
"Here are some small Thunderbolt and USB driver fixes for 5.10-rc4 to
solve some reported issues.
Nothing huge in here, just small things:
- thunderbolt memory leaks fixed and new device ids added
- revert of problem patch for the musb driver
- new quirks added for USB devices
- typec power supply fixes to resolve much reported problems about
charging notifications not working anymore
All except the cdc-acm driver quirk addition have been in linux-next
with no reported issues (the quirk patch was applied on Friday, and is
self-contained)"
* tag 'usb-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode
MAINTAINERS: add usb raw gadget entry
usb: typec: ucsi: Report power supply changes
xhci: hisilicon: fix refercence leak in xhci_histb_probe
Revert "usb: musb: convert to devm_platform_ioremap_resource_byname"
thunderbolt: Add support for Intel Tiger Lake-H
thunderbolt: Only configure USB4 wake for lane 0 adapters
thunderbolt: Add uaccess dependency to debugfs interface
thunderbolt: Fix memory leak if ida_simple_get() fails in enumerate_services()
thunderbolt: Add the missed ida_simple_remove() in ring_request_msix()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Cure the fallout from the MSI irqdomain overhaul which missed that
the Intel IOMMU does not register virtual function devices and
therefore never reaches the point where the MSI interrupt domain is
assigned. This made the VF devices use the non-remapped MSI domain
which is trapped by the IOMMU/remap unit
- Remove an extra space in the SGI_UV architecture type procfs output
for UV5
- Remove a unused function which was missed when removing the UV BAU
TLB shootdown handler"
* tag 'x86-urgent-2020-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
iommu/vt-d: Cure VF irqdomain hickup
x86/platform/uv: Fix copied UV5 output archtype
x86/platform/uv: Drop last traces of uv_flush_tlb_others
|
|
There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially powering it down.
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix leaking netdev device from peripherial devices. The call to allocate the
netdev device is made from and managed by the peripherial.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch creates a common function that peripherials can call to free the
netdev device when failures occur.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Change the order in tcan4x5x_can_remove() to be the exact inverse of
tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the
device.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
devm_regmap_init()
This patch adds the missing error checking when initializing the regmap
interface fails.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
