| Age | Commit message (Collapse) | Author |
|---|
|
Commit b7085c086475 ("cx231xx: convert from pr_foo to dev_foo")
moves usb_get_dev(interface_to_usbdev(interface)) to the beginning
of cx231xx_usb_probe() to use udev->dev in dev_err(),
but it does not make sure usbdev is put on all failure paths.
Later dev_err(udev->dev) was replaced by dev_err(d).
So the patch moves usb_get_dev() below (before the first use)
and fixes another failure path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The following patch fixes an issue observed with 4k sector disks
where the max_hw_sectors attribute was getting set too large in
sd_revalidate_disk. Since sdkp->max_xfer_blocks is in units
of SCSI logical blocks and queue_max_hw_sectors is in units of
512 byte blocks, on a 4k sector disk, every time we went through
sd_revalidate_disk, we were taking the current value of
queue_max_hw_sectors and increasing it by a factor of 8. Fix
this by only shifting sdkp->max_xfer_blocks.
Cc: stable@vger.kernel.org
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This fixes a regression caused by commit 1d5203 ("scsi: handle more device
handler setup/teardown in common code").
The bug is that the alua detach() callout will try to access the
sddev->scsi_dh_data, but we have already set it to NULL. This patch
moves the clearing of that field to after detach() is called.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This commit moves the "buffer in use" logic from the .buf_cleanup
handler into .stop_streaming, based on advice that this is its
proper logical home.
By ensuring the list of pointers in priv->queue_buf[] is managed
as soon as possible, we avoid warnings concerning buffers in ACTIVE
state when the system cleans up after streaming stops. This fixes a
problem with modification of buffers after their content has been
cleared for passing to userspace.
After the refactoring, the buf_init and buf_cleanup functions were
found to contain only initialisation/release steps as are carried out
elsewhere if omitted; these functions and references were removed.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The code that tests that capture from a stream has stopped is
presently insufficient and the potential for a race condition
exists where frame capture may generate an interrupt between
requesting the capture process halt and freeing buffers.
This patch refactors code out of rcar_vin_videobuf_release() and
into rcar_vin_wait_stop_streaming(), and ensures there are calls
in places where we need to know that capturing has finished.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Reuse the v4l2 size definitions from v4l2-image-sizes.h.
So we can remove the rudundent definitions from ov2640.c.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
A hunk, removing this code has been lost between versions 6 and 7 of
patch "soc-camera: add V4L2-async support." The code is harmless, but
redundant.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Now that the bitstream buffer is only allocated for the BIT decoder
case, we can use bitstream.size to check for bitstream ringbuffer
operation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The BIT encoder does not use a per-context bitstream ringbuffer as it encodes
directly into the videobuf2 capture queue's buffers. Avoid allocation of the
bitstream ringbuffer for encoder contexts.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
In preparation for CODA9 JPEG support, allow contexts that
control hardware units directly, without the BIT processor.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Make sure the buffer_mutex lock is taken in coda_bit_release
while coda_free_framebuffers and coda_free_context_buffers
are called.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
In preparation for CODA9 JPEG support, which doesn't have to call
SEQ_END on the BIT processor.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Since we have to copy from input buffers into the bitstream ringbuffer
with the CPU, there is no need for contiguous DMA buffers on the decoder
input side.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Call coda_estimate_sizeimage from both try_fmt and set_defaults to
avoid this v4l2-compliance warning on the h.264 decoder video device:
G_FMT: 1920x1088, 32315559, 1, 1920, 1048576, 3, 0, 0, feedcafe
TRY/S_FMT: 1920x1088, 32315559, 1, 1920, 3133440, 3, 0, 0, feedcafe
fail: v4l2-test-formats.cpp(948): Video Capture: S_FMT(G_FMT) != G_FMT
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
reference buffers
On i.MX6, two subsampling ping-pong buffers are used for motion estimation and
deblocking They should not be counted as framebuffers, or they will be also used
to store reconstructed frames, causing visible artifacts in P-frames.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch queues seq_end_work and flushes the queue during stop_streaming
and clears the ctx->initialized flag. This allows to start streaming again
after stopping streaming without releasing the context.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The isequence counter is never used, qsequence counts the buffers queued into
the bit decoder bitstream ringbuffer. It needs to be reset in stop_streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Compare rounded up width to fit into bytesperline.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
To make sure a set RET_DEC_PIC_SUCCESS flag is not a leftover from
a previous successful run, clear it in prepare_decode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Zeroing the SRAM on probe helps with debugging SRAM contents.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
On 1 and 2 bytes per word, the transfer of the 3 last bytes will access
memory outside tx_ptr.
Although this has not trigger any error on real hardware, we should
better fix this.
Fixes: 24ba5e593f391507 (Remove rx_fn and tx_fn pointer)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Properly zero the structure on the stack before using it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
v4l2-compliance complains about invalid colorspace settings being accepted
on the output side. This patch only allows REC709 and JPEG.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Clarify whether job_ready returns false because the context is on hold, waiting
for new input buffers, whether there are not enough input buffers to fill two
into the bitstream, or whether there is not enough data in the bitstream buffer
for the bitstream reader hardware to read a whole frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
If userspace doesn't properly separate the bitstream input into
individual frames (which may happen for example on slightly
corrupted streams) the CODA hardware may decode more frames
than we expect. We already log an error in this case, but it's
also necessary to adjust the sequence offset. Otherwise we
spam the log with a sequence number mismatch on every frame
frame after the unexpected one.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Handle an empty buffer metadata list without crashing. This can happen
if the decoder is fed a broken stream, or multiple compressed frames in
a single queued buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Do not remove the per-context debugfs directory before the
per-buffer debugfs entries contained therein.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch fixes the ENC_SEQ_RC_PARA initial delay and bitrate masks.
These bit fields are 15 bit wide, not 7 bit.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The decoder should handle V4L2_DEC_CMD_STOP to trigger drain,
but it currently expecting V4L2_ENC_CMD_STOP.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The MFC driver has two controls, DISPLAY_DELAY and DISPLAY_DELAY_ENABLE
that allow forcing the decoder to return a decoded frame sooner
regardless of the order. The added support for firmware version 6 and
higher was not taking into account the DISPLAY_DELAY_ENABLE boolean.
Instead it had a comment stating that DISPLAY_DELAY should be set to a
negative value to disable it. This is not possible since the control
range is from 0 to 65535. This feature was also supposed to be disabled
by default in order to produce frames in display order.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use the GPIO descriptor API instead of the deprecated legacy GPIO API to
manage the busy GPIO.
The patch updates both the jz4740 nand driver and the only user of the driver
the qi-lb60 board driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The Intel Snowfield Peak Bluetooth controllers use a strict scanning
filter policy that filters based on Bluetooth device addresses and
not on RSSI.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This patch changes a BUG_ON() statement to pr_debug, in case the user tries to
update a non-existing queue.
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Ben Goz <ben.goz@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for retrieving port level statistics from device.
Hook is added for ethtool's stats functionality. For example,
$ ethtool -S eth3
NIC statistics:
rx_packets: 12
rx_bytes: 2790
rx_dropped: 0
rx_errors: 0
tx_packets: 8
tx_bytes: 728
tx_dropped: 0
tx_errors: 0
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ndo_bridge_setlink/dellink handlers
Currently ndo_bridge_setlink and ndo_bridge_dellink handlers point
to the default switchdev handlers
This follows my bonding driver changes.
I have only compile tested this patch. However similar
bonding code has been tested.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ndo_bridge_setlink/dellink handlers
We want bond to pick up the offload flag if any of its slaves have it.
NETIF_F_HW_SWITCH_OFFLOAD flag is added to the mask, so that
netdev_increment_features does not ignore it.
This also adds ndo_bridge_setlink and ndo_bridge_dellink handlers.
These currently point to the default handlers provided by the
switchdev api.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch sets the NETIF_F_HW_SWITCH_OFFLOAD feature flag on rocker ports
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
instance
- In tx_hard_error_bump_tc interrupt, tc should be bumped only when current
device instance is in DMA threshold mode. Check per device xstats.threshold
other than global tc.
- Set per device xstats.threshold to SF_DMA_MODE when current device
instance is set to SF mode.
v2-changes:
- fix ident style
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit dc9daab226aa ("cxgb4: Added support in debugfs to dump
sge_qinfo") a preprocessor check for CONFIG_CXGB4_DCB got added, which should
have been CONFIG_CHELSIO_T4_DCB. After adding the right preprocessor, build
fails due to missing function ethqset2pinfo. Fixing that as well.
V2: Updated description since the patch also fixes build failure
Reported-by: Paul Bolle <pebolle@tiscal.nl>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 8eb23b9f35aae413140d3fda766a98092c21e9b0
sched: Debug nested sleeps
causes false-positive warnings in RAID5 code.
This annotation removes them and adds a comment
explaining why there is no real problem.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If a non-page-aligned write is destined for a device which
is missing/faulty, we can deadlock.
As the target device is missing, a read-modify-write cycle
is not possible.
As the write is not for a full-page, a recontruct-write cycle
is not possible.
This should be handled by logic in fetch_block() which notices
there is a non-R5_OVERWRITE write to a missing device, and so
loads all blocks.
However since commit 67f455486d2ea2, that code requires
STRIPE_PREREAD_ACTIVE before it will active, and those circumstances
never set STRIPE_PREREAD_ACTIVE.
So: in handle_stripe_dirtying, if neither rmw or rcw was possible,
set STRIPE_DELAYED, which will cause STRIPE_PREREAD_ACTIVE be set
after a suitable delay.
Fixes: 67f455486d2ea20b2d94d6adf5b9b783d079e321
Cc: stable@vger.kernel.org (v3.16+)
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Previously, we requested that drivers pass ecc.size and ecc.bytes when
using NAND_ECC_SOFT_BCH. However, a driver is likely to only know the ECC
strength required for its NAND, so each driver would need to perform a
strength-to-bytes calculation.
Avoid duplicating this calculation in each driver by asking drivers to
pass ecc.size and ecc.strength so that the strength-to-bytes calculation
need only be implemented once.
This reverts/generalizes this commit:
mtd: nand: Base BCH ECC bytes on required strength
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This patch removes the warnings (space before , ) shown by
checkpatch.pl
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
