| Age | Commit message (Collapse) | Author |
|---|
|
Do not call uart_handle_sysrq_char() if we got any receive error along with
the character, as we don't want random junk to be considered a sysrq.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-4-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check if hardware Rx flood is in progress, and issue soft reset to UART to
stop the flood.
A way to reproduce the flood (checked on iMX6SX) is: open iMX UART at 9600
8N1, and from external source send 0xf0 char at 115200 8N1. In about 90% of
cases this starts a flood of "receiving" of 0xff characters by the iMX UART
that is terminated by any activity on RxD line, or could be stopped by
issuing soft reset to the UART (just stop/start of RX does not help). Note
that in essence what we did here is sending isolated start bit about 2.4
times shorter than it is to be if issued on the UART configured baud rate.
There was earlier attempt to fix similar issue in: 'commit
b38cb7d25711 ("serial: imx: Disable new features of autobaud detection")',
but apparently it only gets harder to reproduce the issue after that
commit.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-3-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We perform soft reset in 2 places, slightly differently for no sufficient
reasons, so move more generic variant to a function, and re-use the code.
Out of 2 repeat counters, 10 and 100, select 10, as the code works at
interrupts disabled, and in practice the reset happens immediately.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-2-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pci1xxxx's quad-uart function has the capability to wake up UART
from suspend state. Enable wakeup before entering into suspend and
disable wakeup on resume.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-5-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pci1xxxx uart supports RS485 mode of operation in the hardware with
auto-direction control with configurable delay for releasing RTS after
the transmission. This patch adds support for the RS485 mode.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-4-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pci1xxxx is a PCIe switch with a multi-function endpoint on one of
its downstream ports. Quad-uart is one of the functions in the
multi-function endpoint. This driver loads for the quad-uart and
enumerates single or multiple instances of uart based on the PCIe
subsystem device ID.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-3-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move implementation of setup_port func() to serial8250_pci_setup_port.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-2-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230202141221.2293012-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Synchronizes hotplug remove with the freeing of the port.
This ensures we have freed all the memory associated with
this port and are not leaking memory.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-6-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When hotplug removing an hvcs device, we need to ensure the
hangup processing is done prior to exiting the remove function,
so use tty_vhangup to do the hangup processing directly
rather than using tty_hangup which simply schedules the hangup
work for later execution.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-5-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Grab a reference to the tty when removing the hvcs to ensure
it does not get freed unexpectedly.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-4-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rather than manually creating attributes for the hvcs driver,
let the driver core do this for us. This also fixes some hotplug
remove issues and ensures that cleanup of these attributes
is done in the right order.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-3-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the dev_groups functionality to manage the attribute groups
for hvcs devices. This simplifies the code and also eliminates
errors coming from kernfs when attempting to remove a console
device that is in use.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-2-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There maybe pending USR interrupt before requesting irq, however
uart_add_one_port has not executed, so there will be kernel panic:
[ 0.795668] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000000000000080
[ 0.802701] Mem abort info:
[ 0.805367] ESR = 0x0000000096000004
[ 0.808950] EC = 0x25: DABT (current EL), IL = 32 bits
[ 0.814033] SET = 0, FnV = 0
[ 0.816950] EA = 0, S1PTW = 0
[ 0.819950] FSC = 0x04: level 0 translation fault
[ 0.824617] Data abort info:
[ 0.827367] ISV = 0, ISS = 0x00000004
[ 0.831033] CM = 0, WnR = 0
[ 0.833866] [0000000000000080] user address but active_mm is swapper
[ 0.839951] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 0.845953] Modules linked in:
[ 0.848869] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.1+g56321e101aca #1
[ 0.855617] Hardware name: Freescale i.MX8MP EVK (DT)
[ 0.860452] pstate: 000000c5 (nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.867117] pc : __imx_uart_rxint.constprop.0+0x11c/0x2c0
[ 0.872283] lr : imx_uart_int+0xf8/0x1ec
The issue only happends in the inmate linux when Jailhouse hypervisor
enabled. The test procedure is:
while true; do
jailhouse enable imx8mp.cell
jailhouse cell linux xxxx
sleep 10
jailhouse cell destroy 1
jailhouse disable
sleep 5
done
And during the upper test, press keys to the 2nd linux console.
When `jailhouse cell destroy 1`, the 2nd linux has no chance to put
the uart to a quiese state, so USR1/2 may has pending interrupts. Then
when `jailhosue cell linux xx` to start 2nd linux again, the issue
trigger.
In order to disable irqs before requesting them, both UCR1 and UCR2 irqs
should be disabled, so here fix that, disable the Ageing Timer interrupt
in UCR2 as UCR1 does.
Fixes: 8a61f0c70ae6 ("serial: imx: Disable irqs before requesting them")
Suggested-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20230206013016.29352-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The previous 'commit 846651eca073 ("serial: fsl_lpuart: RS485 RTS
polariy is inverse")' only fixed the inverse issue on lpuart 8bit
platforms.
This is a follow-up patch to fix the RS485 polarity inverse
issue on lpuart 32bit platforms.
Fixes: 03895cf41d18 ("tty: serial: fsl_lpuart: Add support for RS-485")
Reported-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230207162420.3647904-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.3 merge window
This includes following Thunderbolt/USB4 changes for the v6.3 merge
window:
- Add support for DisplayPort bandwidth allocation mode
- Debug logging improvements
- Minor cleanups.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Add missing kernel-doc comment to tb_tunnel_maximum_bandwidth()
thunderbolt: Handle bandwidth allocation mode enablement notification
thunderbolt: Add support for DisplayPort bandwidth allocation mode
thunderbolt: Include the additional DP IN double word in debugfs dump
thunderbolt: Add functions to support DisplayPort bandwidth allocation mode
thunderbolt: Increase timeout of DP OUT adapter handshake
thunderbolt: Take CL states into account when waiting for link to come up
thunderbolt: Improve debug logging in tb_available_bandwidth()
thunderbolt: Log DP adapter type
thunderbolt: Use decimal port number in control and tunnel logs too
thunderbolt: Refactor tb_acpi_add_link()
thunderbolt: Use correct type in tb_port_is_clx_enabled() prototype
|
|
Current taprio software implementation is haunted by the shadow of the
igb/igc hardware model. It iterates over child qdiscs in increasing
order of TXQ index, therefore giving higher xmit priority to TXQ 0 and
lower to TXQ N. According to discussions with Vinicius, that is the
default (perhaps even unchangeable) prioritization scheme used for the
NICs that taprio was first written for (igb, igc), and we have a case of
two bugs canceling out, resulting in a functional setup on igb/igc, but
a less sane one on other NICs.
To the best of my understanding, taprio should prioritize based on the
traffic class, so it should really dequeue starting with the highest
traffic class and going down from there. We get to the TXQ using the
tc_to_txq[] netdev property.
TXQs within the same TC have the same (strict) priority, so we should
pick from them as fairly as we can. We can achieve that by implementing
something very similar to q->curband from multiq_dequeue().
Since igb/igc really do have TXQ 0 of higher hardware priority than
TXQ 1 etc, we need to preserve the behavior for them as well. We really
have no choice, because in txtime-assist mode, taprio is essentially a
software scheduler towards offloaded child tc-etf qdiscs, so the TXQ
selection really does matter (not all igb TXQs support ETF/SO_TXTIME,
says Kurt Kanzenbach).
To preserve the behavior, we need a capability bit so that taprio can
determine if it's running on igb/igc, or on something else. Because igb
doesn't offload taprio at all, we can't piggyback on the
qdisc_offload_query_caps() call from taprio_enable_offload(), but
instead we need a separate call which is also made for software
scheduling.
Introduce two static keys to minimize the performance penalty on systems
which only have igb/igc NICs, and on systems which only have other NICs.
For mixed systems, taprio will have to dynamically check whether to
dequeue using one prioritization algorithm or using the other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN8841 is completely integrated triple-speed (10BASE-T/ 100BASE-TX/
1000BASE-T) Ethernet physical layer transceivers for transmission and
reception of data on standard CAT-5, as well as CAT-5e and CAT-6,
unshielded twisted pair (UTP) cables.
The LAN8841 offers the industry-standard GMII/MII as well as the RGMII.
Some of the features of the PHY are:
- Wake on LAN
- Auto-MDIX
- IEEE 1588-2008 (V2)
- LinkMD Capable diagnosis
Currently the patch offers support only for link configuration.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add flower filter packet statistics. This will just read the TCAM
counter of the rule, which mention how many packages were hit by this
rule.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Arınç reports that on his MT7621AT Unielec U7621-06 board and MT7623NI
Bananapi BPI-R2, packets received by the CPU over mt7530 switch port 0
(of which this driver acts as the DSA master) are not processed
correctly by software. More precisely, they arrive without a DSA tag
(in packet or in the hwaccel area - skb_metadata_dst()), so DSA cannot
demux them towards the switch's interface for port 0. Traffic from other
ports receives a skb_metadata_dst() with the correct port and is demuxed
properly.
Looking at mtk_poll_rx(), it becomes apparent that this driver uses the
skb vlan hwaccel area:
union {
u32 vlan_all;
struct {
__be16 vlan_proto;
__u16 vlan_tci;
};
};
as a temporary storage for the VLAN hwaccel tag, or the DSA hwaccel tag.
If this is a DSA master it's a DSA hwaccel tag, and finally clears up
the skb VLAN hwaccel header.
I'm guessing that the problem is the (mis)use of API.
skb_vlan_tag_present() looks like this:
#define skb_vlan_tag_present(__skb) (!!(__skb)->vlan_all)
So if both vlan_proto and vlan_tci are zeroes, skb_vlan_tag_present()
returns precisely false. I don't know for sure what is the format of the
DSA hwaccel tag, but I surely know that lowermost 3 bits of vlan_proto
are 0 when receiving from port 0:
unsigned int port = vlan_proto & GENMASK(2, 0);
If the RX descriptor has no other bits set to non-zero values in
RX_DMA_VTAG, then the call to __vlan_hwaccel_put_tag() will not, in
fact, make the subsequent skb_vlan_tag_present() return true, because
it's implemented like this:
static inline void __vlan_hwaccel_put_tag(struct sk_buff *skb,
__be16 vlan_proto, u16 vlan_tci)
{
skb->vlan_proto = vlan_proto;
skb->vlan_tci = vlan_tci;
}
What we need to do to fix this problem (assuming this is the problem) is
to stop using skb->vlan_all as temporary storage for driver affairs, and
just create some local variables that serve the same purpose, but
hopefully better. Instead of calling skb_vlan_tag_present(), let's look
at a boolean has_hwaccel_tag which we set to true when the RX DMA
descriptors have something. Disambiguate based on netdev_uses_dsa()
whether this is a VLAN or DSA hwaccel tag, and only call
__vlan_hwaccel_put_tag() if we're certain it's a VLAN tag.
Arınç confirms that the treatment works, so this validates the
assumption.
Link: https://lore.kernel.org/netdev/704f3a72-fc9e-714a-db54-272e17612637@arinc9.com/
Fixes: 2d7605a72906 ("net: ethernet: mtk_eth_soc: enable hardware DSA untagging")
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unsupported port speed can be set and cause error. Now fixing it
and return an error if setting unsupported speed.
This fix depends on the following, which was included in v6.2-rc1:
commit a61474c41e8c ("nfp: ethtool: support reporting link modes").
Fixes: 7c698737270f ("nfp: add support for .set_link_ksettings()")
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parameters 'queue_index' and 'napi_id' are passed in a swapped order.
Fix it here.
Fixes: 23233e577ef9 ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The special tag is only enabled when the first MAC uses DSA. However, it
must be enabled when any MAC uses DSA. Change the check accordingly.
This fixes hardware DSA untagging not working on the second MAC of the
MT7621 and MT7623 SoCs, and likely other SoCs too. Therefore, remove the
check that disables hardware DSA untagging for the second MAC of the MT7621
and MT7623 SoCs.
Fixes: a1f47752fd62 ("net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC")
Co-developed-by: Richard van Schagen <richard@routerhints.com>
Signed-off-by: Richard van Schagen <richard@routerhints.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This does not fix a real bug, since virtual addresses
are currently indentical to physical ones.
Reviewed-by: Nico Boehr <nrb@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
|
|
The irdma driver can use a maximum number of msix vectors equal
to num_online_cpus() + 1 and the kernel warning stack below is shown
if that number is exceeded.
The kernel throws a warning as the driver tries to update the affinity
hint with a CPU mask greater than the max CPU IDs. Fix this by capping
the MSIX vectors to num_online_cpus() + 1.
WARNING: CPU: 7 PID: 23655 at include/linux/cpumask.h:106 irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
RIP: 0010:irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
Call Trace:
irdma_rt_init_hw+0xa62/0x1290 [irdma]
? irdma_alloc_local_mac_entry+0x1a0/0x1a0 [irdma]
? __is_kernel_percpu_address+0x63/0x310
? rcu_read_lock_held_common+0xe/0xb0
? irdma_lan_unregister_qset+0x280/0x280 [irdma]
? irdma_request_reset+0x80/0x80 [irdma]
? ice_get_qos_params+0x84/0x390 [ice]
irdma_probe+0xa40/0xfc0 [irdma]
? rcu_read_lock_bh_held+0xd0/0xd0
? irdma_remove+0x140/0x140 [irdma]
? rcu_read_lock_sched_held+0x62/0xe0
? down_write+0x187/0x3d0
? auxiliary_match_id+0xf0/0x1a0
? irdma_remove+0x140/0x140 [irdma]
auxiliary_bus_probe+0xa6/0x100
__driver_probe_device+0x4a4/0xd50
? __device_attach_driver+0x2c0/0x2c0
driver_probe_device+0x4a/0x110
__driver_attach+0x1aa/0x350
bus_for_each_dev+0x11d/0x1b0
? subsys_dev_iter_init+0xe0/0xe0
bus_add_driver+0x3b1/0x610
driver_register+0x18e/0x410
? 0xffffffffc0b88000
irdma_init_module+0x50/0xaa [irdma]
do_one_initcall+0x103/0x5f0
? perf_trace_initcall_level+0x420/0x420
? do_init_module+0x4e/0x700
? __kasan_kmalloc+0x7d/0xa0
? kmem_cache_alloc_trace+0x188/0x2b0
? kasan_unpoison+0x21/0x50
do_init_module+0x1d1/0x700
load_module+0x3867/0x5260
? layout_and_allocate+0x3990/0x3990
? rcu_read_lock_held_common+0xe/0xb0
? rcu_read_lock_sched_held+0x62/0xe0
? rcu_read_lock_bh_held+0xd0/0xd0
? __vmalloc_node_range+0x46b/0x890
? lock_release+0x5c8/0xba0
? alloc_vm_area+0x120/0x120
? selinux_kernel_module_from_file+0x2a5/0x300
? __inode_security_revalidate+0xf0/0xf0
? __do_sys_init_module+0x1db/0x260
__do_sys_init_module+0x1db/0x260
? load_module+0x5260/0x5260
? do_syscall_64+0x22/0x450
do_syscall_64+0xa5/0x450
entry_SYSCALL_64_after_hwframe+0x66/0xdb
Fixes: 44d9e52977a1 ("RDMA/irdma: Implement device initialization definitions")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Sindhu Devale <sindhu.devale@intel.com>
Link: https://lore.kernel.org/r/20230207201938.1329-1-sindhu.devale@intel.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Replace the readl and writel with regmap to ease debugging the registers
from userspace.
Suggested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
There's no need to use threaded IRQs with the PXP, as the interrupt
handler doesn't need to sleep and doesn't perform any time-consuming
operation. Switch to regular IRQ handler.
This fixes lockups of the PXP noticed on i.MX7, where the PXP would stop
generating interrupts after a variable number of frames (from a few
dozens to a few hundreds). The root cause is however unknown.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add pxp_read() and pxp_write() functions to wrap readl() and writel()
respectively. This can be useful for debugging register accesses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Implement support for the VIDIOC_ENUM_FRAMESIZES ioctl.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The find_format() function looks up format information for a given pixel
format. It takes a v4l2_format pointer, but only uses the contained
pixel format value. To prepare it for being used by callers that don't
have v4l2_format, modify it to take the pixel format value directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Register a media device for the PXP, using the v4l2-mem2mem MC
infrastructure to populate the media graph. No media device operation is
implemented, the main use of the MC API is to allow consistent discovery
of media devices for userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The v4l2_capability.bus_info field is set by the V4L2 core when left
empty by the .querycap() handler. This is the recommended practice, in
order to ensure bus_info coherence between drivers. Don't set it
manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Sorting headers alphabetically helps locating duplicates, and make it
easier to figure out where to insert new headers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The i.MX7D needs a different data path configuration than the i.MX6ULL.
Configure the data path as close as possible to the data path on the
i.MX6ULL.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Unfortunately, the PXP_HW_VERSION register reports the PXP on the i.MX7D
and on the i.MX6ULL as version 3.0, although the PXP versions on these
SoCs have significant differences.
Use the compatible to configure the ctrl0 register as required dependent
on the platform.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The LUT block is always configured in bypass mode.
Take it entirely out of the pipeline by disabling it and routing the
data path around the LUT.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Various multiplexers in the pipeline are not used with the currently
configured data path. Disable all unused multiplexers by selecting the
"no output" (3) option.
The datasheet doesn't explicitly require this, but the PXP has been seen
to hang after processing a few hundreds of frames otherwise.
As at it, add documentation for the multiplexers that are actually
relevant for the data path.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The driver must configure the data path through the Pixel Pipeline.
Currently, the driver is using a fixed setup, but once there are
different pipeline configurations, it is helpful to have a dedicated
function for determining the register value for the data path.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Different versions of the Pixel Pipeline have different blocks and their
routing may be different. Read the PXP_HW_VERSION register to determine
the version of the PXP and print it to the log for debugging purposes.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The .set_fmt() handler is responsible for adjusting the requested format
based on the device limitations. Implement .init_cfg() as a wrapper of
.set_fmt(), to ensure that the initial configuration always matches the
rules implemented in .set_fmt(), should they ever change.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn-beacon
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Use the V4L2 subdev active state API to store the active format. This
simplifies the driver not only by dropping the mipi_csis_device csis_fmt
and format_mbus fields, but it also allows dropping the device lock,
replaced with the state lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn-beacon
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
To prepare for usage of the subdev active state that will replace the
csis_fmt and format_mbus fields stored in the mipi_csis_device
structure, pass the format explicitly to the functions called when
starting streaming to avoid accessing those two fields. Not functional
change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn-beacon
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The runtime PM handlers don't need manual locking as
- they are serialized by the runtime PM core
- they can't race with other functions taking the same lock, as they
don't access any data protect by that lock
Drop the locking.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn-beacon
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
It is customary to prefix error labels with 'err_' to make their purpose
clearer. Do so in the probe function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn-beacon
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Use the V4L2 subdev active state API to store the active format. This
simplifies the driver not only by dropping the state stored in the
imx7_csi structure, but also by replacing the manual lock with the state
lock.
The is_streaming field is now protected by the active state lock, either
explicitly in .s_stream(), where the active state is locked manually, or
implicitly in .set_fmt(), which is called with the state locked.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The v4l2_subdev_format structure passed to the .get_fmt() subdev
operation in imx7_csi_video_validate_fmt() isn't zeroed, which can cause
undefined behaviour. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
It's good practice for functions to perform error cleanup internally
when they fail, in order to not leave the device in a half-initialized
state. Move the async notifier cleanup from the probe error path to the
imx7_csi_async_register(), and drop the v4l2_async_nf_unregister() call
as there is no error path after the async notifier gets registered.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The subdev core guarantees that the .set_fmt() operation is always
called with a valid pad. Drop the unneeded pad checks.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The .s_stream() and .link_validate() operations can't be called with a
NULL src_sd, as subdev nodes are not registered before the async
notifier completes. Remove the unneeded checks.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The .s_stream() operation is guaranteed not to be called to start/stop
an already started/stopped subdev. Remove the unneeded check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
