| Age | Commit message (Collapse) | Author |
|---|
|
There are uniform, non-uniform and flexible erase flash configurations.
The non-uniform erase types, are the erase types that can _not_ erase
the entire flash by their own.
As the code was, in case flashes had flexible erase capabilities
(support both uniform and non-uniform erase types in the same flash
configuration) and supported multiple uniform erase type sizes, the
code did not sort the uniform erase types, and could select a wrong
erase type size.
Sort the uniform erase mask in case of flexible erase flash
configurations, in order to select the best uniform erase type size.
Uniform, non-uniform, and flexible configurations with just a valid
uniform erase type, are not affected by this change.
Uniform erase tested on mx25l3273fm2i-08g and sst26vf064B-104i/sn.
Non uniform erase tested on sst26vf064B-104i/sn.
Fixes: 5390a8df769e ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Trivial fix to spelling mistake in DRM_DEV_ERROR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106154022.9209-1-colin.king@canonical.com
|
|
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for two Primax mice as well.
0x4e22 is the Dell MS111-P and 0x4d0f is the unbranded HP Portia
mouse HP 697738-001. Both were built until approx. 2014.
Those were the standard mice from those vendors and are still
around - even as new old stock.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/11
Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull in v4.20-rc3 via drm-next.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
idVendor 0x0572
idProduct 0x1349
Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clean up fixed point temp variable initialization, use the more
conventional tmp name for temp variables, add empty lines before
return. No functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-5-jani.nikula@intel.com
|
|
Simply return the condition. No functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-4-jani.nikula@intel.com
|
|
No need to use a compound statement enclosed in parenthesis where a C99
compound literal will do. No functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-3-jani.nikula@intel.com
|
|
While at it, conform to kernel spacing (i.e. no space) after cast. No
functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-2-jani.nikula@intel.com
|
|
Reduce bloat in one of the bigger header files. Fix some indentation
while at it. No functional changes.
v2: Add include guards (Joonas)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-1-jani.nikula@intel.com
|
|
Under moderate amounts of GPU stress, we can observe on Bearlake and
Pineview (later gen3 models) that we execute the following batch buffer
before the write into the batch is coherent. Adding extra (tested with
upto 32x) MI_FLUSH to either the invalidation, flush or both phases does
not solve the incoherency issue with the relocations, but emitting the
MI_STORE_DWORD_IMM twice does. So be it.
Fixes: 7dd4f6729f92 ("drm/i915: Async GPU relocation processing")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119154153.15327-1-chris@chris-wilson.co.uk
|
|
kbuild test robot reports:
>> ERROR: "i2c_mux_add_adapter" [drivers/gpu/drm/bridge/sii902x.ko] undefined!
>> ERROR: "i2c_mux_alloc" [drivers/gpu/drm/bridge/sii902x.ko] undefined!
>> ERROR: "i2c_mux_del_adapters" [drivers/gpu/drm/bridge/sii902x.ko] undefined!
Quite obviously the driver depends on I2C_MUX, but adding a "depends on"
introduces a recursive dependency, therefore this patch selects I2C_MUX
instead.
Fixes: 21d808405fe4 ("drm/bridge/sii902x: Fix EDID readback")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Link: https://lists.01.org/pipermail/kbuild-all/2018-November/054924.html
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1542633978-22064-1-git-send-email-fabrizio.castro@bp.renesas.com
|
|
Since capturing the error state requires fiddling around with the GGTT
to read arbitrary buffers and is itself run under stop_machine(), it
deadlocks the machine (effectively a hard hang) when run in conjunction
with Broxton's VTd workaround to serialize GGTT access.
v2: Store the ERR_PTR in first_error so that the error can be reported
to the user via sysfs.
v3: Mention the quirk in dmesg (using info as per usual)
Fixes: 0ef34ad6222a ("drm/i915: Serialize GTT/Aperture accesses on BXT")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-5-chris@chris-wilson.co.uk
(cherry picked from commit fb6f0b64e455b207a636346588e65bf9598d30eb)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-11-19
The following fixes are for mlx5 core and netdev driver.
For -stable v4.16
bc7fda7d4637 ('net/mlx5e: IPoIB, Reset QP after channels are closed')
For -stable v4.17
36917a270395 ('net/mlx5: IPSec, Fix the SA context hash key')
For -stable v4.18
6492a432be3a ('net/mlx5e: Always use the match level enum when parsing TC rule match')
c3f81be236b1 ('net/mlx5e: Removed unnecessary warnings in FEC caps query')
c5ce2e736b64 ('net/mlx5e: Fix selftest for small MTUs')
For -stable v4.19
effcd896b25e ('net/mlx5e: Adjust to max number of channles when re-attaching')
394cbc5acd68 ('net/mlx5e: RX, verify received packet size in Linear Striding RQ')
447cbb3613c8 ('net/mlx5e: Don't match on vlan non-existence if ethertype is wildcarded')
c223c1574612 ('net/mlx5e: Claim TC hw offloads support only under a proper build config')
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes to use rtnl_lock only during a reset to avoid
deadlock that could occur when a thread operating close is holding
rtnl_lock and waiting for reset_lock acquired by another thread,
which is waiting for rtnl_lock in order to set the number of tx/rx
queues during a reset.
Also, we now setting the number of tx/rx queues during a soft reset
for failover or LPM events.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.
The patch consists of 3 fixes:
- When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
returned PQ 0, which can potentially be another function's pq. Verify
that flag is enabled, otherwise return default start_pq.
- When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
returned NULL and could lead to a segmentation fault. Return default
start_pq instead.
- A modulo operation was added to MCOS/VFS PQ getters to make sure the
PQ returned is in range of the required flag.
Fixes: b5a9ee7cf3be ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the condition which verifies that only one flag is set. The API
bitmap_weight() should receive size in bits instead of bytes.
Fixes: b5a9ee7cf3be ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If FEC caps query fails when executing 'ethtool <interface>'
the whole callback fails unnecessarily, fixed that by replacing the
error return code with debug logging only.
Fixes: 6cfa94605091 ("net/mlx5e: Ethtool driver callback for query/set FEC policy")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Querying interface FEC caps with 'ethtool [int]' after link reset
throws warning regading link speed.
This warning is not needed as there is already an indication in
user space that the link is not up.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This bug would result in reading wrong FEC capabilities for 10G/40G.
Fixes: 2095b2641477 ("net/mlx5e: Add port FEC get/set functions")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Some speeds don't support turning FEC policy off. In case a requested
FEC policy is not supported for a speed (including current speed), its new
FEC policy would be:
no FEC - if disabling FEC is supported for that speed
unchanged - else
Fixes: 2095b2641477 ("net/mlx5e: Add port FEC get/set functions")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Update driver version due to critical bug fixes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ena_remove() we have the following stack call:
ena_remove()
unregister_netdev()
ena_destroy_device()
netif_carrier_off()
Calling netif_carrier_off() causes linkwatch to try to handle the
link change event on the already unregistered netdev, which leads
to a read from an unreadable memory address.
This patch switches the order of the two functions, so that
netif_carrier_off() is called on a regiestered netdev.
To accomplish this fix we also had to:
1. Remove the set bit ENA_FLAG_TRIGGER_RESET
2. Add a sanitiy check in ena_close()
both to prevent double device reset (when calling unregister_netdev()
ena_close is called, but the device was already deleted in
ena_destroy_device()).
3. Set the admin_queue running state to false to avoid using it after
device was reset (for example when calling ena_destroy_all_io_queues()
right after ena_com_dev_reset() in ena_down)
Fixes: 944b28aa2982 ("net: ena: fix missing lock during device destruction")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During resume from hibernation if ena_restore_device fails,
ena_com_dev_reset() is called, and uses the readless read mechanism,
which was already destroyed by the call to
ena_com_mmio_reg_read_request_destroy(). This causes a NULL pointer
reference.
In this commit we switch the call order of the above two functions
to avoid this crash.
Fixes: d7703ddbd7c9 ("net: ena: fix rare bug when failed restart/resume is followed by driver removal")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Loopback test had fixed packet size, which can be bigger than configured
MTU. Shorten the loopback packet size to be bigger than minimal MTU
allowed by the device. Text field removed from struct 'mlx5ehdr'
as redundant to allow send small packets as minimal allowed MTU.
Fixes: d605d66 ("net/mlx5e: Add support for ethtool self diagnostics test")
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In case of striding RQ, we use MPWRQ (Multi Packet WQE RQ), which means
that WQE (RX descriptor) can be used for many packets and so the WQE is
much bigger than MTU. In virtualization setups where the port mtu can
be larger than the vf mtu, if received packet is bigger than MTU, it
won't be dropped by HW on too small receive WQE. If we use linear SKB in
striding RQ, since each stride has room for mtu size payload and skb
info, an oversized packet can lead to crash for crossing allocated page
boundary upon the call to build_skb. So driver needs to check packet
size and drop it.
Introduce new SW rx counter, rx_oversize_pkts_sw_drop, which counts the
number of packets dropped by the driver for being too large.
As a new field is added to the RQ struct, re-open the channels whenever
this field is being used in datapath (i.e., in the case of linear
Striding RQ).
Fixes: 619a8f2a42f1 ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The mirror and not the output count is the one denoting a split.
Fix to condition the offload attempt on the mirror count being > 0
along the firmware to have the related capability.
Fixes: 592d36515969 ("net/mlx5e: Parse mirroring action for offloaded TC eswitch flows")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Yossi Kuperman <yossiku@mellanox.com>
Reviewed-by: Chris Mi <chrism@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When core driver enters deattach/attach flow after pci reset,
Number of logical CPUs may have changed.
As a result we need to update the cpu affiliated resource tables.
1. indirect rqt list
2. eq table
Reproduction (PowerPC):
echo 1000 > /sys/kernel/debug/powerpc/eeh_max_freezes
ppc64_cpu --smt=on
# Restart driver
modprobe -r ... ; modprobe ...
# Link up
ifconfig ...
# Only physical CPUs
ppc64_cpu --smt=off
# Inject PCI errors so PCI will reset - calling the pci error handler
echo 0x8000000000000000 > /sys/kernel/debug/powerpc/<PCI BUS>/err_injct_inboundA
Call trace when trying to add non-existing rqs to an indirect rqt:
mlx5e_redirect_rqt+0x84/0x260 [mlx5_core] (unreliable)
mlx5e_redirect_rqts+0x188/0x190 [mlx5_core]
mlx5e_activate_priv_channels+0x488/0x570 [mlx5_core]
mlx5e_open_locked+0xbc/0x140 [mlx5_core]
mlx5e_open+0x50/0x130 [mlx5_core]
mlx5e_nic_enable+0x174/0x1b0 [mlx5_core]
mlx5e_attach_netdev+0x154/0x290 [mlx5_core]
mlx5e_attach+0x88/0xd0 [mlx5_core]
mlx5_attach_device+0x168/0x1e0 [mlx5_core]
mlx5_load_one+0x1140/0x1210 [mlx5_core]
mlx5_pci_resume+0x6c/0xf0 [mlx5_core]
Create cq will fail when trying to use non-existing EQ.
Fixes: 89d44f0a6c73 ("net/mlx5_core: Add pci error handlers to mlx5_core driver")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
We get the match level (none, l2, l3, l4) while going over the match
dissectors of an offloaded tc rule. When doing this, the match level
enum and the not min inline enum values should be used, fix that.
This worked accidentally b/c both enums have the same numerical values.
Fixes: d708f902989b ('net/mlx5e: Get the required HW match level while parsing TC flow matches')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, we are only supporting tc hw offloads when the eswitch
support is compiled in, but we are not gating the adevertizment
of the NETIF_F_HW_TC feature on this config being set.
Fix it, and while doing that, also avoid dealing with the feature
on ethtool when the config is not set.
Fixes: e8f887ac6a45 ('net/mlx5e: Introduce tc offload support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For the "all" ethertype we should not care whether the packet has
vlans. Besides being wrong, the way we did it caused FW error
for rules such as:
tc filter add dev eth0 protocol all parent ffff: \
prio 1 flower skip_sw action drop
b/c the matching meta-data (outer headers bit in struct mlx5_flow_spec)
wasn't set. Fix that by matching on vlan non-existence only if we were
also told to match on the ethertype.
Fixes: cee26487620b ('net/mlx5e: Set vlan masks for all offloaded TC rules')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Slava Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The mlx5e channels should be closed before mlx5i_uninit_underlay_qp
puts the QP into RST (reset) state during mlx5i_close. Currently QP
state incorrectly set to RST before channels got deactivated and closed,
since mlx5_post_send request expects QP in RTS (Ready To Send) state.
The fix is to keep QP in RTS state until mlx5e channels get closed
and to reset QP afterwards.
Also this fix is simply correct in order to keep the open/close flow
symmetric, i.e mlx5i_init_underlay_qp() is called first thing at open,
the correct thing to do is to call mlx5i_uninit_underlay_qp() last thing
at close, which is exactly what this patch is doing.
Fixes: dae37456c8ac ("net/mlx5: Support for attaching multiple underlay QPs to root flow table")
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The commit "net/mlx5: Refactor accel IPSec code" introduced a
bug where asynchronous short time change in hash key value
by create/release SA context might happen during an asynchronous
hash resize operation this could cause a subsequent remove SA
context operation to fail as the key value used during resize is
not the same key value used when remove SA context operation is
invoked.
This commit fixes the bug by defining the SA context hash key
such that it includes only fields that never change during the
lifetime of the SA context object.
Fixes: d6c4f0298cec ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The current Cadence QSPI driver caused a kernel panic sporadically
when writing to QSPI. The problem was caused by writing more bytes
than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 11.202044] Unable to handle kernel paging request at virtual address bffd3000
[ 11.209254] pgd = e463054d
[ 11.211948] [bffd3000] *pgd=2fffb811, *pte=00000000, *ppte=00000000
[ 11.218202] Internal error: Oops: 7 [#1] SMP ARM
[ 11.222797] Modules linked in:
[ 11.225844] CPU: 1 PID: 1317 Comm: systemd-hwdb Not tainted 4.17.7-d0c45cd44a8f
[ 11.235796] Hardware name: Altera SOCFPGA Arria10
[ 11.240487] PC is at __raw_writesl+0x70/0xd4
[ 11.244741] LR is at cqspi_write+0x1a0/0x2cc
</snip>
On a page boundary limit the number of bytes copied from the tx buffer
to remain within the page.
This patch uses a temporary buffer to hold the 4 bytes to write and then
copies only the bytes required from the tx buffer.
Reported-by: Adrian Amborzewicz <adrian.ambrozewicz@intel.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Reading the sysfs files pp_sclk_od and pp_mclk_od return the
percentage difference between the VBIOS-provided default
frequency and the current (possibly user-set) frequency in
the highest SCLK and MCLK DPM states, respectively.
Writing to these files provides an easy mechanism for
setting a higher-than-default maximum frequency. We
normally only allow values >= 0 to be written here.
However, with the addition of pp_od_clk_voltage, we now
allow users to set custom DPM tables. If they then set
the maximum DPM state to something less than the default,
later reads of pp_*_od should return a negative value.
The highest DPM state is now less than the VBIOS-provided
default, so the percentage is negative.
The math to calculate this was originally performed with
unsigned values, meaning reads that should return negative
values returned meaningless data. This patch corrects that
issue and normalizes how all of the calculations are done
across the various hwmgr types.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Joseph Greathouse <Joseph.Greathouse@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Due to lack of MODULE_FIRMWARE() with hainan_mc.bin, the driver
doesn't work properly in initrd. Let's add it.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1116239
Fixes: 8eaf2b1faaf4 ("drm/amdgpu: switch firmware path for SI parts")
Cc: <stable@vger.kernel.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Disable these features on Vega20 for now.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Feifei Xu<Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On Vega20 and other pre-production GPUs, powerplay is not enabled yet.
Check for NULL pointers before calling pp_funcs function pointers.
Also affects Kaveri.
CC: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Pull networking fixes from David Miller:
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
|
|
Since capturing the error state requires fiddling around with the GGTT
to read arbitrary buffers and is itself run under stop_machine(), it
deadlocks the machine (effectively a hard hang) when run in conjunction
with Broxton's VTd workaround to serialize GGTT access.
v2: Store the ERR_PTR in first_error so that the error can be reported
to the user via sysfs.
v3: Mention the quirk in dmesg (using info as per usual)
Fixes: 0ef34ad6222a ("drm/i915: Serialize GTT/Aperture accesses on BXT")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-5-chris@chris-wilson.co.uk
|
|
LG touchscreen (1fd2:8001) stops working after reboot:
[ 4.859153] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 4.936070] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 9.948224] i2c_hid i2c-SAPS2101:00: failed to reset device.
The device in question stops working after receives SLEEP, ON, SLEEP
commands in a short period. The scenario is like this:
- Once the desktop session closes, it also closed the hid device, so the
device gets runtime suspended and receives a SLEEP command.
- Before calling shutdown callback, it gets runtime resumed and received
an ON command.
- In the shutdown callback, it receives another SLEEP command.
I failed to find a reliable interval between ON/SLEEP commands that can
make it work, so let's simply disable runtime PM for the device.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Cirque Touchpad/Pointstick combo is similar to Alps devices, it requires
MT_CLS_WIN_8_DUAL to expose its pointstick as a mouse.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Previously, when a HID client such as the Steam Client was running, this
driver disabled its input device to avoid doubling the input events.
While it worked mostly fine, some games got confused by the idle gamepad,
and switched to two player mode, or asked the user to choose which gamepad
to use. Other games just crashed, probably a bug in Unity [1].
With this commit, when a HID client starts, the input device is removed;
when the HID client ends the input device is recreated.
[1]: https://github.com/ValveSoftware/steam-for-linux/issues/5645
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some of the functions (like cdn_dp_dpcd_read, cdn_dp_get_edid_block)
allow to read 64KiB, but the cdn_dp_mailbox_read_receive, that is
used by them, can read only up to 255 bytes at once. Normally, it's
not a big issue as DPCD or EDID reads won't (hopefully) exceed that
value.
The real issue here is the revocation list read during the HDCP
authentication process. (problematic use case:
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/rockchip/cdn-dp-reg.c#1152)
The list can reach 127*5+4 bytes (num devs * 5 bytes per ID/Bksv +
4 bytes of an additional info).
In other words - CTSes with HDCP Repeater won't pass without this
fix. Oh, and the driver will most likely stop working (best case
scenario).
Signed-off-by: Damian Kos <dkos@cadence.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1541518625-25984-1-git-send-email-dkos@cadence.com
|
|
This reverts commit 336fd4f5f25157e9e8bd50e898a1bbcd99eaea46.
Please note that `strlcpy()` does *NOT* do what you think it does.
strlcpy() *ALWAYS* reads the full input string, regardless of the
'length' parameter. That is, if the input is not zero-terminated,
strlcpy() will *READ* beyond input boundaries. It does this, because it
always returns the size it *would* copy if the target was big enough,
not the truncated size it actually copied.
The original code was perfectly fine. The hid device is
zero-initialized and the strncpy() functions copied up to n-1
characters. The result is always zero-terminated this way.
This is the third time someone tried to replace strncpy with strlcpy in
this function, and gets it wrong. I now added a comment that should at
least make people reconsider.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When a UHID_CREATE command is written to the uhid char device, a
copy_from_user() is done from a user pointer embedded in the command.
When the address limit is KERNEL_DS, e.g. as is the case during
sys_sendfile(), this can read from kernel memory. Alternatively,
information can be leaked from a setuid binary that is tricked to write
to the file descriptor. Therefore, forbid UHID_CREATE in these cases.
No other commands in uhid_char_write() are affected by this bug and
UHID_CREATE is marked as "obsolete", so apply the restriction to
UHID_CREATE only rather than to uhid_char_write() entirely.
Thanks to Dmitry Vyukov for adding uhid definitions to syzkaller and to
Jann Horn for commit 9da3f2b740544 ("x86/fault: BUG() when uaccess
helpers fault on kernel addresses"), allowing this bug to be found.
Reported-by: syzbot+72473edc9bf4eb1c6556@syzkaller.appspotmail.com
Fixes: d365c6cfd337 ("HID: uhid: add UHID_CREATE and UHID_DESTROY events")
Cc: <stable@vger.kernel.org> # v3.6+
Cc: Jann Horn <jannh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jann Horn <jannh@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
GLK firmware can indicate that the tuning value will be restored after
runtime suspend, but not actually do that. Add a workaround that detects
such cases, and lets the driver do re-tuning instead.
Reported-by: Anisse Astier <anisse@astier.eu>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
I have a Thinkpad X220 Tablet in my hands that is losing vblank
interrupts whenever LP3 watermarks are used.
If I nudge the latency value written to the WM3 register just
by one in either direction the problem disappears. That to me
suggests that the punit will not enter the corrsponding
powersave mode (MPLL shutdown IIRC) unless the latency value
in the register matches exactly what we read from SSKPD. Ie.
it's not really a latency value but rather just a cookie
by which the punit can identify the desired power saving state.
On HSW/BDW this was changed such that we actually just write
the WM level number into those bits, which makes much more
sense given the observed behaviour.
We could try to handle this by disallowing LP3 watermarks
only when vblank interrupts are enabled but we'd first have
to prove that only vblank interrupts are affected, which
seems unlikely. Also we can't grab the wm mutex from the
vblank enable/disable hooks because those are called with
various spinlocks held. Thus we'd have to redesigne the
watermark locking. So to play it safe and keep the code
simple we simply disable LP3 watermarks on all SNB machines.
To do that we simply zero out the latency values for
watermark level 3, and we adjust the watermark computation
to check for that. The behaviour now matches that of the
g4x/vlv/skl wm code in the presence of a zeroed latency
value.
v2: s/USHRT_MAX/U32_MAX/ for consistency with the types (Chris)
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101269
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103713
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114173440.6730-1-ville.syrjala@linux.intel.com
(cherry picked from commit 03981c6ebec4fc7056b9b45f847393aeac90d060)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Hide the enable_gvt modparam in the default scenario where
support has not been compiled in.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116144447.7836-1-joonas.lahtinen@linux.intel.com
|
|
Userspace portion is still missing.
This reverts commit 9fa6e2f7609fdbb7d6f86be86371a5719bec0376.
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116135510.13807-2-joonas.lahtinen@linux.intel.com
|
