| Age | Commit message (Collapse) | Author |
|---|
|
Tegra124 has been randomly hanging during system suspend when entering
the Tegra LP1 low power state. The hang is caused by the Tegra SDHCI
driver and linked to the UHS-I tuning sequence. Disabling the UHS-I
modes for Tegra124 prevents any hangs from occurring when entering
system suspend.
Unfortunately, the tuning sequence described in the public Tegra
documentation is incomplete and on inspection of the current tuning
sequence that has been implemented is also incomplete and may cause
problems. In the short-term it is safer to disable UHS-I modes for now
and fix later because it would be too large of a change to simply patch
now. Therefore, disable UHS-I modes for Tegra124.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit 520bd7a8b415 ("mmc: core: Optimize boot time by detecting cards
simultaneously") causes regressions for some platforms.
These platforms relies on fixed mmcblk device indexes, instead of
deploying the defacto standard with UUID/PARTUUID. In other words their
rootfs needs to be available at hardcoded paths, like /dev/mmcblk0p2.
Such guarantees have never been made by the kernel, but clearly the above
commit changes the behaviour. More precisely, because of that the order
changes of how cards becomes detected, so do their corresponding mmcblk
device indexes.
As the above commit significantly improves boot time for some platforms
(magnitude of seconds), let's avoid reverting this change but instead
restore the behaviour of how mmcblk device indexes becomes picked.
By using the same index for the mmcblk device as for the corresponding mmc
host device, the probe order of mmc host devices decides the index we get
for the mmcblk device.
For those platforms that suffers from a regression, one could expect that
this updated behaviour should be sufficient to meet their expectations of
"fixed" mmcblk device indexes.
Another side effect from this change, is that the same index is used for
the mmc host device, the mmcblk device and the mmc block queue. That
should clarify their relationship.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: 520bd7a8b415 ("mmc: core: Optimize boot time by detecting cards
simultaneously")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-04-13
This series contains updates to i40e, i40evf and fm10k.
Alex fixes a bug introduced earlier based on his interpretation of the
XL710 datasheet. The actual limit for fragments with TSO and a skbuff
that has payload data in the header portion of the buffer is actually
only 7 fragments and the skb-data portion counts as 2 buffers, one for
the TSO header, and the one for a segment payload buffer.
Jacob fixes a bug where in a previous refactor of the code broke
multi-bit updates for VFs. The problem occurs because a multi-bit
request has a non-zero length, and the PF would simply drop any
request with the upper 16 bits set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix the issue that when resume back, uvd/vce
dpm was disabled and uvd/vce's performace
dropped.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This got lost somewhere along the way. This fixes
audio not working until set_property was called.
Noticed-by: Hyungwon Hwang <hyungwon.hwang7@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The VF uses a multi-bit update request to clear unused VLANs whenever it
resets. However, an accident in a previous refector broke multi-bit
updates for VFs, due to misreading a comment in fm10k_vf.c and
attempting to reduce code duplication. The problem occurs because
a multi-bit request has a non-zero length, and the PF would simply drop
any request with the upper 16 bits set.
We can't simply remove the check of the upper 16 bits and the call to
fm10k_iov_select vid, because this would remove the checks for default
VID and for ensuring no other VLANs can be enabled except pf_vid when it
has been set. To resolve that issue, this revision uses the
iov_select_vid when we have a single-bit update, and denies any
multi-bit update when the VLAN was administratively set by the PF. This
should be ok since the PF properly updates VLAN_TABLE when it assigns
the PF vid. This ensures that requests to add or remove the PF vid work
as expected, but a rogue VF could not use the multi-bit update as
a loophole to attempt receiving traffic on other VLANs.
Reported-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
commit b7d3e3d3d21a ("net: thunderx: Don't leak phy device references
on -EPROBE_DEFER condition.") incorrectly moved the call to
of_node_put() outside of the loop. Under normal loop exit, the node
has already had of_node_put() called, so the extra call results in:
[ 8.228020] ERROR: Bad of_node_put() on /soc@0/pci@848000000000/mrml-bridge0@1,0/bgx0/xlaui00
[ 8.239433] CPU: 16 PID: 608 Comm: systemd-udevd Not tainted 4.6.0-rc1-numa+ #157
[ 8.247380] Hardware name: www.cavium.com EBB8800/EBB8800, BIOS 0.3 Mar 2 2016
[ 8.273541] Call trace:
[ 8.273550] [<fffffc0008097364>] dump_backtrace+0x0/0x210
[ 8.273557] [<fffffc0008097598>] show_stack+0x24/0x2c
[ 8.273560] [<fffffc0008399ed0>] dump_stack+0x8c/0xb4
[ 8.273566] [<fffffc00085aa828>] of_node_release+0xa8/0xac
[ 8.273570] [<fffffc000839cad8>] kobject_cleanup+0x8c/0x194
[ 8.273573] [<fffffc000839c97c>] kobject_put+0x44/0x6c
[ 8.273576] [<fffffc00085a9ab0>] of_node_put+0x24/0x30
[ 8.273587] [<fffffc0000bd0f74>] bgx_probe+0x17c/0xcd8 [thunder_bgx]
[ 8.273591] [<fffffc00083ed220>] pci_device_probe+0xa0/0x114
[ 8.273596] [<fffffc0008473fbc>] driver_probe_device+0x178/0x418
[ 8.273599] [<fffffc000847435c>] __driver_attach+0x100/0x118
[ 8.273602] [<fffffc0008471b58>] bus_for_each_dev+0x6c/0xac
[ 8.273605] [<fffffc0008473884>] driver_attach+0x30/0x38
[ 8.273608] [<fffffc00084732f4>] bus_add_driver+0x1f8/0x29c
[ 8.273611] [<fffffc0008475028>] driver_register+0x70/0x110
[ 8.273617] [<fffffc00083ebf08>] __pci_register_driver+0x60/0x6c
[ 8.273623] [<fffffc0000bf0040>] bgx_init_module+0x40/0x48 [thunder_bgx]
[ 8.273626] [<fffffc0008090d04>] do_one_initcall+0xcc/0x1c0
[ 8.273631] [<fffffc0008198abc>] do_init_module+0x68/0x1c8
[ 8.273635] [<fffffc0008125668>] load_module+0xf44/0x11f4
[ 8.273638] [<fffffc0008125b64>] SyS_finit_module+0xb8/0xe0
[ 8.273641] [<fffffc0008093b30>] el0_svc_naked+0x24/0x28
Go back to the previous (correct) code that only did the extra
of_node_put() call on early exit from the loop.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
fix some exynos regressions.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Use VIDEO_SAMSUNG_S5P_G2D=n as G2D Kconfig dependency
drm/exynos: fix a warning message
drm/exynos: mic: fix an error code
drm/exynos: fimd: fix broken dp_clock control
drm/exynos: build fbdev code conditionally
drm/exynos: fix adjusted_mode pointer in exynos_plane_mode_set
drm/exynos: fix error handling in exynos_drm_subdrv_open
|
|
into drm-fixes
some misc radeon fixes.
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/amdgpu: fix irq domain remove for tonga ih
drm/radeon: use helper for mst connector dpms.
drm/radeon/mst: port some MST setup code from DAL.
drm/amdgpu: add invisible pin size statistic
|
|
Add validation code into mISDN/socket.c
Signed-off-by: Emrah Demir <ed@abdsec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses a bug introduced based on my interpretation of the
XL710 datasheet. Specifically section 8.4.1 states that "A single transmit
packet may span up to 8 buffers (up to 8 data descriptors per packet
including both the header and payload buffers)." It then later goes on to
say that each segment for a TSO obeys the previous rule, however it then
refers to TSO header and the segment payload buffers.
I believe the actual limit for fragments with TSO and a skbuff that has
payload data in the header portion of the buffer is actually only 7
fragments as the skb->data portion counts as 2 buffers, one for the TSO
header, and one for a segment payload buffer.
Fixes: 2d37490b82af ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The clk API may return 0 on clk_get_rate, so we should check the result before
using it as a divisor.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.6
b43
* fix memory leaks when removing the device
bcma
* fix building without OF_IRQ
rtlwifi
* fix gcc-6 indentation warning
iwlwifi
* lower the debug level of a benign print
* fix a memory leak
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a buffer is being dequeued using VIDIOC_DQBUF IOCTL, the exact buffer
which will be dequeued is not known until the buffer has been removed from
the queue. The number of planes is specific to a buffer, not to the queue.
This does lead to the situation where multi-plane buffers may be requested
and queued with n planes, but VIDIOC_DQBUF IOCTL may be passed an argument
struct with fewer planes.
__fill_v4l2_buffer() however uses the number of planes from the dequeued
videobuf2 buffer, overwriting kernel memory (the m.planes array allocated
in video_usercopy() in v4l2-ioctl.c) if the user provided fewer
planes than the dequeued buffer had. Oops!
Fixes: b0e0e1f83de3 ("[media] media: videobuf2: Prepare to divide videobuf2")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v4.4 and later
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The number of planes in videobuf2 is specific to a buffer. In order to
verify that the planes array provided by the user is long enough, a new
vb2_buf_op is required.
Call __verify_planes_array() when the dequeued buffer is known. Return an
error to the caller if there was one, otherwise remove the buffer from the
done list.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v4.4 and later
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
AMD Seattle SATA controller mostly conforms to AHCI interface with some
special register to control SGPIO interface. In the case of an AHCI
controller, the SGPIO feature is ideally implemented using the
"Enclosure Management" register of the AHCI controller, but those
registeres are not implemented in the Seattle SoC. Instead SoC
(Rev B0 onwards) provides a 32-bit SGPIO control register which should
be programmed to control the activity, locate and fault LEDs.
The driver is based on ahci_platform driver.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: tj@kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
On BXT platform Host Controller and Device Controller figure as
same PCI device but with different device function. HCD should
not pass data to Device Controller but only to Host Controllers.
Checking if companion device is Host Controller, otherwise skip.
Cc: <stable@vger.kernel.org>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Cc: stable@vger.kernel.org
Reported-and-tested-by: David Webb <djw@noc.ac.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 64d513ac31bd ("scsi: use host wide tags by default") causes
the SCSI core to queue more commands then we can handle on devices with
multiple LUNs, limit the queue depth at the scsi-host level instead of
per slave to fix this.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1315013
Cc: stable@vger.kernel.org # 4.4.x and 4.5.x
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Otherwise generic-xhci and xhci-platform which have no data get wrongly
detected as XHCI_PLAT_TYPE_MARVELL_ARMADA by xhci_plat_type_is().
This fixes a regression in v4.5 for STiH407 family SoC's which use the
synopsis dwc3 IP, whereby the disable_clk error path gets taken due to
wrongly being detected as XHCI_PLAT_TYPE_MARVELL_ARMADA and the hcd never
gets added.
I suspect this will also fix other dwc3 DT platforms such as Exynos,
although I've only tested on STih410 SoC.
Fixes: 4efb2f694114 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: stable@vger.kernel.org
Cc: gregory.clement@free-electrons.com
Cc: yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes some wild pointers produced by xhci_mem_cleanup.
These wild pointers will cause system crash if xhci_mem_cleanup()
is called twice.
Reported-and-tested-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue that cannot work if R-Car Gen2/3 run on
above 4GB physical memory environment to use a quirk XHCI_NO_64BIT_SUPPORT.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of
HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
address memory pointers actually. So, in this case, this driver should
call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup().
Otherwise, the xHCI controller will be died after a usb device is
connected if it runs on above 4GB physical memory environment.
So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve
such an issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Cc: <stable@vger.kernel.org>
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Broxton B0 also requires XHCI_PME_STUCK_QUIRK.
Adding PCI device ID for Broxton B and adding to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Under some circumstances acm_tty_flush_chars() is called
with no buffer to flush. We simply need to do nothing.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit 895005202987 ("dmaengine: dw: apply both HS interfaces and remove
slave_id usage") cleaned up the code to avoid usage of depricated slave_id
member of generic slave configuration.
Meanwhile it broke the master selection by removing important call to
dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from
custom slave configuration to the internal channel structure.
Everything works until now since there is no customized connection of
DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use.
The configurations where 2 masters are connected to the different masters are
not working anymore. We are expecting one user of such configuration and need
to select masters properly. Besides that it is obviously a performance
regression since only one master is in use in multi-master configuration.
Select masters in accordance with what user asked for. Keep this patch in a form
more suitable for back porting.
We are safe to take necessary data in ->device_alloc_chan_resources() because
we don't support generic slave configuration embedded into custom one, and thus
the only way to provide such is to use the parameter to a filter function which
is called exactly before channel resource allocation.
While here, replase BUG_ON to less noisy dev_warn() and prevent channel
allocation in case of error.
Fixes: 895005202987 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes for -rc4, for various platforms.
Nothing really substantial and worth pointing out in particular; small
fixes for various bugs, see shortlog for details"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: sa1100: remove references to the defunct handhelds.org
bus: uniphier-system-bus: fix condition of overlap check
ARM: uniphier: drop weird sizeof()
ARM: dts: am335x-baltos-ir5221: fix cpsw_emac0 link type
ARM: OMAP: Correct interrupt type for ARM TWD
ARM: DRA722: Add ID detect for Silicon Rev 2.0
ARM: dts: am43xx: fix edma memcpy channel allocation
ARM: dts: AM43x-epos: Fix clk parent for synctimer
ARM: OMAP2: Fix up interconnect barrier initialization for DRA7
documentation: Fix pinctrl documentation for Meson8 / Meson8b
ARM: dts: amlogic: Split pinctrl device for Meson8 / Meson8b
ARM: mvebu: Correct unit address for linksys
bus: mvebu-mbus: use %pa to print phys_addr_t
arm64: dts: vulcan: Update PCI ranges
ARM: u8500_defconfig: turn on the Synaptics RMI4 driver
ARM: pxa: fix the number of DMA requestor lines
ARM: OMAP2+: hwmod: Fix updating of sysconfig register
ARM: OMAP2+: Use srst_udelay for USB on dm814x
|
|
The emmc-phy is fully enclosed in the general register files (GRF).
Therefore as seen from the device-tree it shouldn't be a separate platform-
device but instead a sub-device of the GRF - using the simply-mfd mechanism.
The driver entered the kernel in the current merge-window, so we can still
adapt the binding without needing a fallback, as the binding hasn't been
released with a full kernel yet.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The displayport-phy is fully enclosed in the general register files (GRF).
Therefore as seen from the device-tree it shouldn't be a separate platform-
device but instead a sub-device of the GRF - using the simply-mfd mechanism.
The driver entered the kernel in the current merge-window, so we can still
adapt the binding without needing a fallback, as the binding hasn't been
released with a full kernel yet.
While the edp phy is fully part of the GRF, it doesn't have any separate
register set there, so doesn't get any register-area assigned.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This reverts commit cc8ed76938b5cf6a54ab3d60edabaf808dc960d1
("soc: mediatek: SCPSYS: Fix double enabling of regulators") [1].
This patch fixes mt8173-evb failing boot issue. With commit [1],
genpd state will not sync to real power domain state. So some
resources such as clocks and regulators may stay in a wrong state.
There is no regulator double enabling issue on mainline kernel, so
we can refert commit [1] safely.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
commit ee36027427c7 ("clk: imx: Add clock support for imx6qp")
introduced a regression due to a subtle typo in the 'can_root' clock
definition. The effect is that trying to configure the bitrate of the
can interfaces fails with -EDOM or produces a division by zero error
due to the clock_freq of the can serial clock being reported as '0'.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Fixes: ee36027427c7 ("clk: imx: Add clock support for imx6qp")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We clamp frame_len_words to a maximum of 4096, but do not actually
limit the number of words written or read through the DATA registers
or the length added to spi_message::actual_length. This results in
silent data corruption for commands longer than this maximum.
Recalculate the length of each transfer, taking frame_len_words into
account. Use this length in qspi_{read,write}_msg(), and to increment
spi_message::actual_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Each transfer can specify 8, 16 or 32 bits per word independently of
the default for the device being addressed. However, currently we
calculate the number of words in the frame assuming that the word size
is the device default.
If multiple transfers in the same message have differing
bits_per_word, we bitwise-or the different values in the WLEN register
field.
Fix both of these. Also rename 'frame_length' to 'frame_len_words' to
make clear that it's not a byte count like spi_message::frame_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Intel DNV has the same iSMT SMBus host controller than Intel Avoton. Add
DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Broadcom Vulcan ARM64 processor uses the same I2C controller
present on the Broadcom XLP9xx/5xx MIPS processor family.
Updated the Kconfig by adding ARCH_VULCAN option.
Signed-off-by: Tanmay Jagdale <tanmay.jagdale@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Enable the I2C core for this SoC.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
DTK-1651 is a display pen-only tablet
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
mvebu fixes for 4.6 (part 1)
- fix USB adress register for Linksys Armada 388 based boards
- fix build warning in mvebu-mbus
* tag 'mvebu-fixes-4.6-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Correct unit address for linksys
bus: mvebu-mbus: use %pa to print phys_addr_t
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch fixes condition whether the specified address ranges
overlap each other.
Fixes: 4b7f48d395a7 ("bus: uniphier-system-bus: add UniPhier System Bus driver")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 254d4d111ee1 ("drm/exynos: Add dependency for G2D in Kconfig") made
the DRM_EXYNOS_G2D symbol to only be selectable if the s5p-g2d V4L2 driver
is not enabled, since both use the same HW IP block.
But added the dependency as depends on !VIDEO_SAMSUNG_S5P_G2D which isn't
correct since Kconfig expressions are not boolean but tristate. So it will
only evaluate to 'n' if VIDEO_SAMSUNG_S5P_G2D=y but it will evaluate to m
if VIDEO_SAMSUNG_S5P_G2D=m.
This means that both the V4L2 and DRM drivers can be enabled if the former
is enabled as a module, which is not what we want.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The "ret = regmap_write()" assignment was missing so this error message
is never printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
We accidentally return success instead of a negative error code here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Commit 1feafd3afd294b03dbbedb8e8f94e0c4db526f10 ("drm/exynos: add
exynos5420 support for fimd") add support for Exynos 5420 SoC, but it
broke enabling display clock feature because of incorrect condition
check. This patch fixes it, so display is working again on platforms
requiring display clock control (i.e. Exynos5250-based SNOW platform).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Fbdev code should be compiled only if CONFIG_DRM_FBDEV_EMULATION option
is enabled. The patch fixes exynos-drm code trying to manipulate
fbdev data which is not initialized in case CONFIG_DRM_FBDEV_EMULATION
is disabled.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
exynos_plane_mode_set should use adjusted_mode from the same atomic state as
plane state. Otherwise it will result in incorrect behavior in case
crtc mode changes.
The patch fixes bug with black console framebuffer in case of command mode
panels.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
gcc-6 warns about a pointless loop in exynos_drm_subdrv_open:
drivers/gpu/drm/exynos/exynos_drm_core.c: In function 'exynos_drm_subdrv_open':
drivers/gpu/drm/exynos/exynos_drm_core.c:104:199: error: self-comparison always evaluates to false [-Werror=tautological-compare]
list_for_each_entry_reverse(subdrv, &subdrv->list, list) {
Here, the list_for_each_entry_reverse immediately terminates because
the subdrv pointer is compared to itself as the loop end condition.
If we were to take the current subdrv pointer as the start of the
list (as we would do if list_for_each_entry_reverse() was not a macro),
we would iterate backwards over the &exynos_drm_subdrv_list anchor,
which would be even worse.
Instead, we need to use list_for_each_entry_continue_reverse()
to go back over each subdrv that was successfully opened until
the first entry.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The firwmare file can come with data that is relevant for paging. This
data is availablet to the firmware upon request, but it stored in the
host's memory. During the firmware init flow, the driver configures the
firmware so that the firwmare knows where is the data.
When paging is used, the variable paging_mem_size is the number of bytes
that are available through paging. This variable is not zeror-ed if the
driver fails to configure the paging in the firmware, but the memory is
freed which is inconsistent.
This inconsistency led to a NULL pointer dereference in the code that
collects the debug data.
Fix this by zero-ing the paging_mem_size variable and NULLify the
relevant pointers, so that the code that collects the debug data will
know that the paging data is not available.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The firwmare name for 8000 is iwlwifi-8000C. The C is
appended based on a value read from a register. This
allows to load different firwmare versions based on
the hardware step during development. Now that the
hardware development is completed, we can hard code
the 'C' and along the way, fix the input to
MODULE_FIRMWARE.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=116041
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
