| Age | Commit message (Collapse) | Author |
|---|
|
The drm_encoder_cleanup() was missing both from the error path of
dw_hdmi_imx_bind(). This caused a crash when slub_debug was
enabled and we ended up deferring probe of HDMI at boot.
This call isn't needed from unbind() because if dw_hdmi_bind() returns
no error then it takes over the job of freeing the encoder (in
dw_hdmi_unbind).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The driver already advertises multi-planar YUV support, but
previously the U/V offset and stride setup was missing.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The IPU addresses multiplanar formats using a base address and relative
offsets for the secondary planes. Since those offsets must be positive
and not too large, and none of the plane parameters except the base address
may be changed while scanout is active, store the pitches and u/v offsets
and check all values against IDMAC limitations.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Let ipu_cpmem_set_yuv_planar_full take a DRM_FORMAT instead of a
V4L2_PIXFMT and allow better control over U/V stride, U offset and
V offset settings in the CPMEM.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Pull up was reported as pull down and vice versa. Fix this.
Fixes: 8f1774a2a971 "pinctrl: nomadik: improve GPIO debug prints"
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The SPICE protocol considers the position of a cursor to be the location
of its active pixel on the display, so the cursor is drawn with its
top-left corner at "(x - hot_spot_x, y - hot_spot_y)" but the DRM cursor
position gives the location where the top-left corner should be drawn,
with the hotspot being a hint for drivers that need it.
This fixes the location of the window resize cursors when using Fluxbox
with the QXL DRM driver and both the QXL and modesetting X drivers.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1447845445-2116-1-git-send-email-john@metanate.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
commit b37d83a6a414 ("usb: Parse the new USB 3.1 SuperSpeedPlus Isoc
endpoint companion descriptor") caused a regression in 4.6-rc1 and fails
to parse SuperSpeed endpoint companion descriptors.
The new SuperSpeedPlus Isoc endpoint companion parsing code incorrectly
decreased the the remaining buffer size before comparing the size with the
expected length of the descriptor.
This lead to possible failure in reading the SuperSpeed endpoint companion
descriptor of the last endpoint, displaying a message like:
"No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0
ep 129: using minimum values"
Fix it by decreasing the size after comparing it.
Also finish all the SS endpoint companion parsing before calling SSP isoc
endpoint parsing function.
Fixes: b37d83a6a414
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix potential out-of-bounds write to urb->transfer_buffer
usbip handles network communication directly in the kernel. When receiving a
packet from its peer, usbip code parses headers according to protocol. As
part of this parsing urb->actual_length is filled. Since the input for
urb->actual_length comes from the network, it should be treated as untrusted.
Any entity controlling the network may put any value in the input and the
preallocated urb->transfer_buffer may not be large enough to hold the data.
Thus, the malicious entity is able to write arbitrary data to kernel memory.
Signed-off-by: Ignat Korchagin <ignat.korchagin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need to have the WWN fully initialized before addig default groups to it,
so add a new method to add these groups after the WWN has been initialized.
Also remove the default groups in the core while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The iSCSI targets wants to add a default group, for which we need to
have the list of default groups initialized previously.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Instead we can clean up the list of default ACLs in core code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now the rdma core offers a QP draining service in v4.6-rc1,
use it instead of our own.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl. Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The typo caused the wrong flow control bit to be set.
Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size of every padded firmware message is specified in the first
HWRM_VER_GET response message. Use this value to pad every message
after that.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing code does the following:
allocate completion ring
initialize completion ring doorbell
disable interrupts on this completion ring by writing to the doorbell
We can have a race where firmware sends an asynchronous event to the host
after completion ring allocation and before doorbell is initialized.
When this happens driver can crash while ringing the doorbell using
uninitialized value as part of handling the IRQ/napi request.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an issue when we use mavtap over team:
When we replug nic links from team0, the real nics's mc list will not
include the maddr for macvtap any more. then we can't receive pkts to
macvtap device, as they are filterred by mc list of nic.
In Bonding Driver, it syncs the uc/mc addrs in bond_enslave().
We will fix this issue on team by adding the port's uc/mc addrs sync in
team_port_add.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in the case where qed_slowpath_irq_req is not called, rc is not
assigned and so qed_int_igu_enable will return a garbage value.
Fix this by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix crash due to NULL pointer access in max1111 driver"
* tag 'hwmon-for-linus-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max1111) Return -ENODEV from max1111_read_channel if not instantiated
|
|
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When unexpected situation happened (e.g. tx/rx irq happened while
DMAC is used), the usbhsf_pkt_handler() was possible to cause NULL
pointer dereference like the followings:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_acm u_serial g_serial libcomposite
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.5.0-rc6-00842-gac57066-dirty #63
Hardware name: Generic R8A7790 (Flattened Device Tree)
task: c0729c00 ti: c0724000 task.ti: c0724000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xac/0x118
pc : [<00000000>] lr : [<c03257e0>] psr: 60000193
sp : c0725db8 ip : 00000000 fp : c0725df4
r10: 00000001 r9 : 00000193 r8 : ef3ccab4
r7 : ef3cca10 r6 : eea4586c r5 : 00000000 r4 : ef19ceb4
r3 : 00000000 r2 : 0000009c r1 : c0725dc4 r0 : ef19ceb4
This patch adds a condition to avoid the dereference.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Jan reported this:
===
After enabling CONFIG_I2C_DEBUG_CORE my system was broken
(no network, console login not possible). System log was
flooded with the this message:
...
[ 608.052077] rtc-ds1307 0-0068: uevent
[ 608.052500] rtc-ds1307 0-0068: uevent
[ 608.052925] rtc-ds1307 0-0068: uevent
...
The culprit is the dev_dbg printk in the i2c uevent handler.
If this is activated (for instance by CONFIG_I2C_DEBUG_CORE)
it results in an endless loop with systemd-journald.
This happens if user-space scans the system log and reads the uevent
file to get information about a newly created device, which seems fair
use to me. Unfortunately reading the "uevent" file uses the same
function that runs for creating the uevent for a new device,
generating the next syslog entry.
Ideally user-space would implement a recursion detection and
after reading the same device file for the 1000th time call it a
day, but nevertheless I think we should avoid this problem by
removing the debug print completely or using another print variant.
The same problem seems to be reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=76886
===
His patch converted the message to pr_debug, but I think the debug can
simply go. We have other means to see code paths these days. This
enables us to clean up the function some more while we are here.
Reported-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
|
|
buflen by default (256) is smaller than wMaxPacketSize (512) in high-speed
devices.
That caused the OUT endpoint to freeze if the host send any data packet of
length greater than 256 bytes.
This is an example dump of what happended on that enpoint:
HOST: [DATA][Length=260][...]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
...
HOST: [PING]
DEVICE: [NAK]
This patch fixes this problem by setting the minimum usb_request's buffer size
for the OUT endpoint as its wMaxPacketSize.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
gcc warns about the use of regulators in phy_8x16_probe:
drivers/usb/phy/phy-qcom-8x16-usb.c: In function 'phy_8x16_probe':
drivers/usb/phy/phy-qcom-8x16-usb.c:284:13: error: 'regs[0].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/usb/phy/phy-qcom-8x16-usb.c:285:13: error: 'regs[1].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/usb/phy/phy-qcom-8x16-usb.c:286:12: error: 'regs[2].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
According to Mark Brown, this is the result of various abuses
of the PHY interfaces [1], so let's fix the driver instead.
This puts the regulator bulk data into the device structure so it
gets properly initialized and lets us call regulator_bulk_enable()
and regulator_bulk_disable() rather than open-coding them.
Setting the voltages the way the driver does is rather pointless
because for each regulator there is only one valid voltage
range, so that can just get set up in the DT. As there doesn't
seem to be any user of the newly added driver yet, we can simply
make sure the DTs are setting this up right when they get added.
I'm also fixing the handling of regulator_bulk_enable() failure.
Right now, the driver just ignores any failure, which doesn't make
sense, so I'm changing it to loudly complain (in case we actually
had a bug here) and error out.
Doing a fly-by review of the driver, I notice a couple of other
problems that I'm not addressing here:
- It really should not have been written as a USB PHY driver, but
instead should use the PHY subsystem.
- The DT compatible string does not follow the usual conventions,
and it should have a proper identifier in it rather than a wildcard.
- The example in the devicetree binding lists a register address
that is the same as the actual EHCI host controller in the SoC
as well as the otg-snps and the ci-hdrc device, which indicates
that these are probably not even distinct devices (or all but
one of them are wrong), and if more than one of them tries to
request the resources correctly, they fail.
[1] https://lkml.org/lkml/2016/1/26/267
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
A recent change to the mbus driver added a warning printk that
prints a phys_addr_t using the %x format string, which fails in
case we build with 64-bit phys_addr_t:
drivers/bus/mvebu-mbus.c: In function 'mvebu_mbus_get_dram_win_info':
drivers/bus/mvebu-mbus.c:975:9: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'phys_addr_t {aka long long unsigned int}' [-Werror=format=]
This uses the special %pa format string instead, so we always
print the correct type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f2900acea801 ("bus: mvebu-mbus: provide api for obtaining IO and DRAM window information")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
There is unexpected gpio interrupt after irq_enable. If not
implemeted gpio_irq_enable callback, irq_enable calls irq_unmask
instead. But if there was interrupt set before the irq_enable,
unmask it may trigger the unexpected interrupt. By implementing
the gpio_irq_enable callback, do interrupt status ack, the issue
has gone.
Signed-off-by: Qi Zheng <qi.zheng@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
High level trigger mode of GPIO interrupt is not set correctly
in intel_gpio_irq_type(), and will make this kind of interrupt
not respond.
Signed-off-by: Qi Zheng <qi.zheng@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On error path of_iomap() returns NULL, hence IS_ERR() check is invalid
and may cause a NULL pointer dereference, the change fixes this
problem.
While we are here invert a device node check to simplify the code.
Fixes: 26d8cde5260b ("pinctrl: freescale: imx: add shared input select reg support")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.
However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.
Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.
This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
mfio 84 to 89 are described wrongly, fix it to describe
the right pin and add them to right pin-mux group.
The correct order is:
pll1_lock => mips_pll -- MFIO_83
pll2_lock => audio_pll -- MFIO_84
pll3_lock => rpu_v_pll -- MFIO_85
pll4_lock => rpu_l_pll -- MFIO_86
pll5_lock => sys_pll -- MFIO_87
pll6_lock => wifi_pll -- MFIO_88
pll7_lock => bt_pll -- MFIO_89
Cc: linux-gpio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: James Hartley <James.Hartley@imgtec.com>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes: cefc03e5995e("pinctrl: Add Pistachio SoC pin control driver")
Signed-off-by: Govindraj Raja <Govindraj.Raja@imgtec.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If pinctrl_provide_dummies() is used unconditionally, then the dummy
state will be used even on DT platforms when the "init" state was
intentionally left out. Instead of "default", the dummy "init" state
will then be used during probe. Thus, when probing an I2C controller on
cold boot, communication triggered by bus notifiers broke because the
pins were not initialized.
Do it like OMAP2: use the dummy state only for non-DT platforms.
Cc: stable@vger.kernel.org
Fixes: ef0eebc05130 ("drivers/pinctrl: Add the concept of an "init" state")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
platform_get_resource() can return NULL, thus add NULL test to prevent NULL
pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Current code uses a uninitialized spin lock.
bgpio_init() already initialized a spin lock, so let's switch to use
&gc->bgpio_lock instead and remove the lock from struct men_z127_gpio.
Fixes: f436bc2726c6 "gpio: add driver for MEN 16Z127 GPIO controller"
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix support for 16 bit source/dest port matches in ixgbe model.
u32 uses a single 32-bit key value for both source and destination ports
starting at offset 0. So replace the 2 functions with a single function
that takes this key value/mask to program both source and dest ports.
Verified with the following filter:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1: u32 divisor 1
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:10 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:10 u32 ht 1: \
match tcp src 1024 ffff match tcp dst 80 ffff action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:11 u32 ht 1: \
match tcp src 1025 ffff action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:12 u32 ht 1: \
match tcp dst 81 ffff action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field
Verified with the following filters:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: \
match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: \
match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:3 u32 ht 800: \
match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:4 u32 ht 800: \
match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).
Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Return error when a MAC address change is rejected by the PF.
This will prevent the user from modifying the MAC address when
that operation is not permitted.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use udelay instead of usleep_range because this can be called while
a lock is held.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through. However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket. As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.
In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP. In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR. This way we can avoid
having to do any byte swaps in order to validate the port number.
I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct. This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.
In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read. I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
commit c9f53e63c208 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.
This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
While retesting the SRP initiator I ran the command "rmmod mlx4_ib"
while I/O was in progress. That command triggers SCSI device removal
indirectly. Avoid that this action triggers the following deadlock:
=================================
[ INFO: inconsistent lock state ]
4.6.0-rc0-dbg+ #2 Tainted: G O
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
multipathd/484 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&pg->lock)->rlock){+.?...}, at: [<ffffffffa04f50a2>] alua_bus_detach+0x52/0xa0 [scsi_dh_alua]
{IN-SOFTIRQ-W} state was registered at:
[<ffffffff810a64a9>] __lock_acquire+0x7e9/0x1ad0
[<ffffffff810a7fd0>] lock_acquire+0x60/0x80
[<ffffffff8159910e>] _raw_spin_lock_irqsave+0x3e/0x60
[<ffffffffa04f5131>] alua_rtpg_queue+0x41/0x1d0 [scsi_dh_alua]
[<ffffffffa04f5531>] alua_check+0xe1/0x220 [scsi_dh_alua]
[<ffffffffa04f5709>] alua_check_sense+0x99/0xb0 [scsi_dh_alua]
[<ffffffff813f0d01>] scsi_check_sense+0x71/0x3f0
[<ffffffff813f2f8b>] scsi_decide_disposition+0x18b/0x1d0
[<ffffffff813f6e52>] scsi_softirq_done+0x52/0x140
[<ffffffff812a26f2>] blk_done_softirq+0x52/0x90
[<ffffffff8105bc1f>] __do_softirq+0x10f/0x230
[<ffffffff8105bec8>] irq_exit+0xa8/0xb0
[<ffffffff8101a675>] do_IRQ+0x65/0x110
[<ffffffff8159a2c9>] ret_from_intr+0x0/0x19
[<ffffffff811732f1>] kmem_cache_alloc+0x151/0x190
[<ffffffff8118e534>] create_object+0x34/0x2d0
[<ffffffff8158eaa6>] kmemleak_alloc_percpu+0x56/0xd0
[<ffffffff8113ab0d>] pcpu_alloc+0x38d/0x660
[<ffffffff8113aded>] __alloc_percpu_gfp+0xd/0x10
[<ffffffff812e56a5>] __percpu_counter_init+0x55/0xb0
[<ffffffff812b4989>] blkg_alloc+0x79/0x230
[<ffffffff812b6756>] blkcg_init_queue+0x26/0x1d0
[<ffffffff81297eed>] blk_alloc_queue_node+0x27d/0x2e0
[<ffffffffa017766c>] dm_create+0x20c/0x570 [dm_mod]
[<ffffffffa017e356>] dev_create+0x56/0x2c0 [dm_mod]
[<ffffffffa017dcae>] ctl_ioctl+0x26e/0x520 [dm_mod]
[<ffffffffa017df6e>] dm_ctl_ioctl+0xe/0x20 [dm_mod]
[<ffffffff811aa8ee>] do_vfs_ioctl+0x8e/0x660
[<ffffffff811aaefc>] SyS_ioctl+0x3c/0x70
[<ffffffff81599929>] entry_SYSCALL_64_fastpath+0x1c/0xac
irq event stamp: 4290931
hardirqs last enabled at (4290931): [ 1662.892772]
[<ffffffff81599341>] _raw_spin_unlock_irqrestore+0x31/0x50
hardirqs last disabled at (4290930): [<ffffffff815990e7>] _raw_spin_lock_irqsave+0x17/0x60
softirqs last enabled at (4290774): [<ffffffff8105bcdb>] __do_softirq+0x1cb/0x230
softirqs last disabled at (4289831): [<ffffffff8105bec8>] irq_exit+0xa8/0xb0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&pg->lock)->rlock);
<Interrupt>
lock(&(&pg->lock)->rlock);
*** DEADLOCK ***
2 locks held by multipathd/484:
#0: (&bdev->bd_mutex){+.+.+.}, at: [<ffffffff811d1cc3>] __blkdev_put+0x33/0x360
#1: (sd_ref_mutex){+.+...}, at: [<ffffffff81400afc>] scsi_disk_put+0x1c/0x40
stack backtrace:
CPU: 6 PID: 484 Comm: multipathd Tainted: G O 4.6.0-rc0-dbg+ #2
Call Trace:
[<ffffffff812bd115>] dump_stack+0x67/0x92
[<ffffffff810a5175>] print_usage_bug+0x215/0x240
[<ffffffff810a56ea>] mark_lock+0x54a/0x610
[<ffffffff810a6505>] __lock_acquire+0x845/0x1ad0
[<ffffffff810a7fd0>] lock_acquire+0x60/0x80
[<ffffffff81598f23>] _raw_spin_lock+0x33/0x50
[<ffffffffa04f50a2>] alua_bus_detach+0x52/0xa0 [scsi_dh_alua]
[<ffffffff813ff6f7>] scsi_dh_release_device+0x17/0x50
[<ffffffff813fb8da>] scsi_device_dev_release_usercontext+0x2a/0x120
[<ffffffff810701f0>] execute_in_process_context+0x80/0x90
[<ffffffff813fb8a7>] scsi_device_dev_release+0x17/0x20
[<ffffffff813c8cfd>] device_release+0x2d/0x90
[<ffffffff812bfa8a>] kobject_release+0x7a/0x190
[<ffffffff812bf946>] kobject_put+0x26/0x50
[<ffffffff813c8ee2>] put_device+0x12/0x20
[<ffffffff813edc86>] scsi_device_put+0x26/0x30
[<ffffffff81400b0d>] scsi_disk_put+0x2d/0x40
[<ffffffff81400b68>] sd_release+0x48/0xb0
[<ffffffff811d1f2e>] __blkdev_put+0x29e/0x360
[<ffffffff811d24b9>] blkdev_put+0x49/0x170
[<ffffffff811d2600>] blkdev_close+0x20/0x30
[<ffffffff81198f48>] __fput+0xe8/0x1f0
[<ffffffff81199089>] ____fput+0x9/0x10
[<ffffffff81075d9e>] task_work_run+0x6e/0xa0
[<ffffffff81001119>] exit_to_usermode_loop+0xa9/0xb0
[<ffffffff81001590>] syscall_return_slowpath+0xb0/0xc0
[<ffffffff815999b7>] entry_SYSCALL_64_fastpath+0xaa/0xac
Fixes: cb0a168cb6b8 (scsi_dh_alua: update 'access_state' field)
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Avoid that building with W=1 causes gcc to report warnings about symbols
that have not been declared.
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Drivers for these don't exist yet so we will add them as fixed clocks
so we don't BUG() if we change clocks that reference these clocks.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
When this was added not all the remaining defines were switched over to
use enums, so let's complete that process here
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The qcom_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The rst_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
