| Age | Commit message (Collapse) | Author |
|---|
|
Previously, the TX header requirement for standard frames was ignored.
This requirement is a bitstring sent from the VIOS which maps to the
type of header information needed during TX. If no header information,
is needed then send subcrq direct can be used (which can be more
performant).
This bitstring was previously ignored for standard packets (AKA non LSO,
non CSO) due to the belief that the bitstring was over-cautionary. It
turns out that there are some configurations where the backing device
does need header information for transmission of standard packets. If
the information is not supplied then this causes continuous "Adapter
error" transport events. Therefore, this bitstring should be respected
and observed before considering the use of send subcrq direct.
Fixes: 74839f7a8268 ("ibmvnic: Introduce send sub-crq direct")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241001163200.1802522-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix up the ACPI IRQ override quirk list and add two new entries
to it, add a new quirk to the ACPI backlight (video) driver, and fix
the ACPI battery driver.
Specifics:
- Add a quirk for Dell OptiPlex 5480 AIO to the ACPI backlight
(video) driver (Hans de Goede)
- Prevent the ACPI battery driver from crashing when unregistering a
battery hook and simplify battery hook locking in it (Armin Wolf)
- Fix up the ACPI IRQ override quirk list and add quirks for Asus
Vivobook X1704VAP and Asus ExpertBook B2502CVA to it (Hans de
Goede)"
* tag 'acpi-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: battery: Fix possible crash when unregistering a battery hook
ACPI: battery: Simplify battery hook locking
ACPI: video: Add backlight=native quirk for Dell OptiPlex 5480 AIO
ACPI: resource: Add Asus ExpertBook B2502CVA to irq1_level_low_skip_override[]
ACPI: resource: Add Asus Vivobook X1704VAP to irq1_level_low_skip_override[]
ACPI: resource: Loosen the Asus E1404GAB DMI match to also cover the E1404GA
ACPI: resource: Remove duplicate Asus E1504GAB IRQ override
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two cpufreq issues, one in the core and one in the
intel_pstate driver:
- Fix CPU device node reference counting in the cpufreq core (Miquel
Sabaté Solà)
- Turn the spinlock used by the intel_pstate driver in hard IRQ
context into a raw one to prevent the driver from crashing when
PREEMPT_RT is enabled (Uwe Kleine-König)"
* tag 'pm-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid a bad reference count on CPU node
cpufreq: intel_pstate: Make hwp_notify_lock a raw spinlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix a potential NULL-pointer dereference in gpiolib core
- fix a probe() regression from the v6.12 merge window and an older bug
leading to missed interrupts in gpio-davinci
* tag 'gpio-fixes-for-v6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: Fix potential NULL pointer dereference in gpiod_get_label()
gpio: davinci: Fix condition for irqchip registration
gpio: davinci: fix lazy disable
|
|
Pull drm fixes from Dave Airlie:
"Weekly fixes, xe and amdgpu lead the way, with panthor, and few core
components getting various fixes. Nothing seems too out of the
ordinary.
atomic:
- Use correct type when reading damage rectangles
display:
- Fix kernel docs
dp-mst:
- Fix DSC decompression detection
hdmi:
- Fix infoframe size
sched:
- Update maintainers
- Fix race condition whne queueing up jobs
- Fix locking in drm_sched_entity_modify_sched()
- Fix pointer deref if entity queue changes
sysfb:
- Disable sysfb if framebuffer parent device is unknown
amdgpu:
- DML2 fix
- DSC fix
- Dispclk fix
- eDP HDR fix
- IPS fix
- TBT fix
i915:
- One fix for bitwise and logical "and" mixup in PM code
xe:
- Restore pci state on resume
- Fix locking on submission, queue and vm
- Fix UAF on queue destruction
- Fix resource release on freq init error path
- Use rw_semaphore to reduce contention on ASID->VM lookup
- Fix steering for media on Xe2_HPM
- Tuning updates to Xe2
- Resume TDR after GT reset to prevent jobs running forever
- Move id allocation to avoid userspace using a guessed number to
trigger UAF
- Fix OA stream close preventing pbatch buffers to complete
- Fix NPD when migrating memory on LNL
- Fix memory leak when aborting binds
panthor:
- Fix locking
- Set FOP_UNSIGNED_OFFSET in fops instance
- Acquire lock in panthor_vm_prepare_map_op_ctx()
- Avoid uninitialized variable in tick_ctx_cleanup()
- Do not block scheduler queue if work is pending
- Do not add write fences to the shared BOs
vbox:
- Fix VLA handling"
* tag 'drm-fixes-2024-10-04' of https://gitlab.freedesktop.org/drm/kernel: (41 commits)
drm/xe: Fix memory leak when aborting binds
drm/xe: Prevent null pointer access in xe_migrate_copy
drm/xe/oa: Don't reset OAC_CONTEXT_ENABLE on OA stream close
drm/xe/queue: move xa_alloc to prevent UAF
drm/xe/vm: move xa_alloc to prevent UAF
drm/xe: Clean up VM / exec queue file lock usage.
drm/xe: Resume TDR after GT reset
drm/xe/xe2: Add performance tuning for L3 cache flushing
drm/xe/xe2: Extend performance tuning to media GT
drm/xe/mcr: Use Xe2_LPM steering tables for Xe2_HPM
drm/xe: Use helper for ASID -> VM in GPU faults and access counters
drm/xe: Convert to USM lock to rwsem
drm/xe: use devm_add_action_or_reset() helper
drm/xe: fix UAF around queue destruction
drm/xe/guc_submit: add missing locking in wedged_fini
drm/xe: Restore pci state upon resume
drm/amd/display: Fix system hang while resume with TBT monitor
drm/amd/display: Enable idle workqueue for more IPS modes
drm/amd/display: Add HDR workaround for specific eDP
drm/amd/display: avoid set dispclk to 0
...
|
|
The blamed commit introduced an unexpected regression in the sja1105
driver. Packets from VLAN-unaware bridge ports get received correctly,
but the protocol stack can't seem to decode them properly.
For ds->untag_bridge_pvid users (thus also sja1105), the blamed commit
did introduce a functional change: dsa_switch_rcv() used to call
dsa_untag_bridge_pvid(), which looked like this:
err = br_vlan_get_proto(br, &proto);
if (err)
return skb;
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb) && skb->protocol == htons(proto)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
and now it calls dsa_software_vlan_untag() which has just this:
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
thus lacks any skb->protocol == bridge VLAN protocol check. That check
is deferred until a later check for skb->vlan_proto (in the hwaccel area).
The new code is problematic because, for VLAN-untagged packets,
skb_vlan_untag() blindly takes the 4 bytes starting with the EtherType
and turns them into a hwaccel VLAN tag. This is what breaks the protocol
stack.
It would be tempting to "make it work as before" and only call
skb_vlan_untag() for those packets with the skb->protocol actually
representing a VLAN.
But the premise of the newly introduced dsa_software_vlan_untag() core
function is not wrong. Drivers set ds->untag_bridge_pvid or
ds->untag_vlan_aware_bridge_pvid presumably because they send all
traffic to the CPU reception path as VLAN-tagged. So why should we spend
any additional CPU cycles assuming that the packet may be VLAN-untagged?
And why does the sja1105 driver opt into ds->untag_bridge_pvid if it
doesn't always deliver packets to the CPU as VLAN-tagged?
The answer to the latter question is indeed more interesting: it doesn't
need to. This got done in commit 884be12f8566 ("net: dsa: sja1105: add
support for imprecise RX"), because I thought it would be needed, but I
didn't realize that it doesn't actually make a difference.
As explained in the commit message of the blamed patch, ds->untag_bridge_pvid
only makes a difference in the VLAN-untagged receive path of a bridge port.
However, in that operating mode, tag_sja1105.c makes use of VLAN tags
with the ETH_P_SJA1105 TPID, and it decodes and consumes these VLAN tags
as if they were DSA tags (aka tag_8021q operation). Even if commit
884be12f8566 ("net: dsa: sja1105: add support for imprecise RX") added
this logic in sja1105_bridge_vlan_add():
/* Always install bridge VLANs as egress-tagged on the CPU port. */
if (dsa_is_cpu_port(ds, port))
flags = 0;
that was for _bridge_ VLANs, which are _not_ committed to hardware
in VLAN-unaware mode (aka the mode where ds->untag_bridge_pvid does
anything at all). Even prior to that change, the tag_8021q VLANs
were always installed as egress-tagged on the CPU port, see
dsa_switch_tag_8021q_vlan_add():
u16 flags = 0; // egress-tagged, non-PVID
if (dsa_port_is_user(dp))
flags |= BRIDGE_VLAN_INFO_UNTAGGED |
BRIDGE_VLAN_INFO_PVID;
err = dsa_port_do_tag_8021q_vlan_add(dp, info->vid,
flags);
if (err)
return err;
Whether the sja1105 driver needs the new flag, ds->untag_vlan_aware_bridge_pvid,
rather than ds->untag_bridge_pvid, is a separate discussion. To fix the
current bug in VLAN-unaware bridge mode, I would argue that the sja1105
driver should not request something it doesn't need, rather than
complicating the core DSA helper. Whereas before the blamed commit, this
setting was harmless, now it has caused breakage.
Fixes: 93e4649efa96 ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241001140206.50933-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull block fixes from Jens Axboe:
- Fix another use-after-free in aoe
- Fixup wrong nested non-saving irq disable/restore in blk-iocost
- Fixup a kerneldoc complaint introduced by a merge window patch
* tag 'block-6.12-20241004' of git://git.kernel.dk/linux:
aoe: fix the potential use-after-free problem in more places
blk_iocost: remove some duplicate irq disable/enables
block: fix blk_rq_map_integrity_sg kernel-doc
|
|
Merge an ACPI backlight (video) quirk and ACPI battery driver fix and
cleanup for 6.12-rc2:
- Add a quirk for Dell OptiPlex 5480 AIO to the ACPI backlight (video)
driver (Hans de Goede).
- Prevent the ACPI battery driver from crashing when unregistering a
battery hook and simplify battery hook locking in it (Armin Wolf).
* acpi-video:
ACPI: video: Add backlight=native quirk for Dell OptiPlex 5480 AIO
* acpi-battery:
ACPI: battery: Fix possible crash when unregistering a battery hook
ACPI: battery: Simplify battery hook locking
|
|
The object pointed to by tz->tzp may still be accessed after being
freed in thermal_zone_device_unregister(), so move the freeing of it
to the point after the removal completion has been completed at which
it cannot be accessed any more.
Fixes: 3d439b1a2ad3 ("thermal/core: Alloc-copy-free the thermal zone parameters structure")
Cc: 6.8+ <stable@vger.kernel.org> # 6.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/4623516.LvFx2qVVIh@rjwysocki.net
|
|
There are places in the thermal netlink code where nothing prevents
the thermal zone object from going away while being accessed after it
has been returned by thermal_zone_get_by_id().
To address this, make thermal_zone_get_by_id() get a reference on the
thermal zone device object to be returned with the help of get_device(),
under thermal_list_lock, and adjust all of its callers to this change
with the help of the cleanup.h infrastructure.
Fixes: 1ce50e7d408e ("thermal: core: genetlink support for events/cmd/sampling")
Cc: 6.8+ <stable@vger.kernel.org> # 6.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/6112242.lOV4Wx5bFT@rjwysocki.net
|
|
The intent of this debugfs entry is to allow modification of wedging
behavior, either from IGT tests or during manual debug; it should be
marked as writable to properly reflect this. In practice this hasn't
caused a problem because we always access wedged_mode as root, which
ignores file permissions, but it's still misleading to have the entry
incorrectly marked as RO.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: 6b8ef44cc0a9 ("drm/xe: Introduce the wedged_mode debugfs")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241002230620.1249258-2-matthew.d.roper@intel.com
|
|
I have a ASUS PN51 S mini pc that has two xhci devices. One from AMD,
and other from ASMEDIA. The one from ASMEDIA have problems when resume
from suspend, and keep broken until unplug the power cord. I use this
kernel parameter: xhci-hcd.quirks=128 and then it works ok. I make a
path to reset only the ASMEDIA xhci.
Signed-off-by: Jose Alberto Reguero <jose.alberto.reguero@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240919184202.22249-1-jose.alberto.reguero@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
support
Introduce new kernel config symbol for Microchip usb5744 SMBus programming
support. Since usb5744 i2c initialization routine uses i2c SMBus APIs these
APIs should only be invoked when kernel has I2C support. This new kernel
config describes the dependency on I2C kernel support and fix the below
build issues when USB_ONBOARD_DEV=y and CONFIG_I2C=m.
riscv64-linux-ld: drivers/usb/misc/onboard_usb_dev.o:
undefined reference to `i2c_find_device_by_fwnode'
drivers/usb/misc/onboard_usb_dev.c:408:(.text+0xb24): undefined
reference to `i2c_smbus_write_block_data'
<snip>
Parsing of the i2c-bus bus handle is not put under usb5744 kernel config
check as the intention is to report an error when DT is configured for
usb5744 SMBus support and kernel has USB_ONBOARD_DEV_USB5744 disabled.
Fixes: 6782311d04df ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409140539.3Axwv38m-lkp@intel.com/
Acked-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Link: https://lore.kernel.org/r/1727529992-476088-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit addresses an issue where events were being processed when
the controller was in a halted state. To fix this issue by stop
processing the events as the event count was considered stale or
invalid when the controller was halted.
Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Cc: stable@kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240916231813.206-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When dwc3_resume_common() returns an error, runtime pm is left in
suspended and disabled state in dwc3_resume(). Since the device
is suspended, its parent devices (like the power domain or glue
driver) could also be suspended and may have released resources
that dwc requires. Consequently, calling dwc3_suspend_common() in
this situation could result in attempts to access unclocked or
unpowered registers.
To prevent these problems, runtime PM should always be re-enabled,
even after failed resume attempts. This ensures that
dwc3_suspend_common() is skipped in such cases.
Fixes: 68c26fe58182 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable@vger.kernel.org
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240913232145.3507723-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
JieLi tends to use SCSI via USB Mass Storage to implement their own
proprietary commands instead of implementing another USB interface.
Enumerating it as a generic mass storage device will lead to a Hardware
Error sense key get reported.
Ignore this bogus device to prevent appearing a unusable sdX device
file.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241001083407.8336-1-uwu@icenowy.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Registering a gadget driver is expected to complete synchronously and
immediately after calling driver_register() this function checks that
the driver has bound so as to return an error.
Set PROBE_FORCE_SYNCHRONOUS to ensure this is the case even when
asynchronous probing is set as the default.
Fixes: fc274c1e99731 ("USB: gadget: Add a new bus for gadgets")
Cc: stable@vger.kernel.org
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20240913102325.2826261-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Backmerging to resolve a conflict with core locally.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Fix the uninitialized symbol 'rv' in the function ish_fw_xfer_direct_dma
to resolve the following warning from the smatch tool:
drivers/hid/intel-ish-hid/ishtp-fw-loader.c:714 ish_fw_xfer_direct_dma()
error: uninitialized symbol 'rv'.
Initialize 'rv' to 0 to prevent undefined behavior from uninitialized
access.
Cc: stable@vger.kernel.org
Fixes: 91b228107da3 ("HID: intel-ish-hid: ISH firmware loader client driver")
Signed-off-by: SurajSonawane2415 <surajsonawane0215@gmail.com>
Link: https://patch.msgid.link/20241004075944.44932-1-surajsonawane0215@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
As of commit 2edc6a75f26c ("drm/i915: switch intel_wakeref_t underlying
type to struct ref_tracker *") we gained quite a few sparse warnings
about "Using plain integer as NULL pointer" for using 0 to initialize
wakeref_t. Switch to NULL everywhere.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241002181655.582597-1-jani.nikula@intel.com
|
|
The only input fc_rport_set_marginal_state() currently accepts is
"Marginal" when port_state is "Online", and "Online" when the port_state
is "Marginal". It should also allow setting port_state to its current
state, either "Marginal or "Online".
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Link: https://lore.kernel.org/r/20240917230643.966768-1-bmarzins@redhat.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A regression was introduced with commit dbb2da557a6a ("scsi: wd33c93:
Move the SCSI pointer to private command data") which results in an oops
in wd33c93_intr(). That commit added the scsi_pointer variable and
initialized it from hostdata->connected. However, during selection,
hostdata->connected is not yet valid. Fix this by getting the current
scsi_pointer from hostdata->selecting.
Cc: Daniel Palmer <daniel@0x0f.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@kernel.org
Fixes: dbb2da557a6a ("scsi: wd33c93: Move the SCSI pointer to private command data")
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Co-developed-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/09e11a0a54e6aa2a88bd214526d305aaf018f523.1727926187.git.fthain@linux-m68k.org
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After commit 379a58caa199 ("scsi: fnic: Move fnic_fnic_flush_tx() to a
work queue"), it can happen that a work item is sent to an uninitialized
work queue. This may has the effect that the item being queued is never
actually queued, and any further actions depending on it will not
proceed.
The following warning is observed while the fnic driver is loaded:
kernel: WARNING: CPU: 11 PID: 0 at ../kernel/workqueue.c:1524 __queue_work+0x373/0x410
kernel: <IRQ>
kernel: queue_work_on+0x3a/0x50
kernel: fnic_wq_copy_cmpl_handler+0x54a/0x730 [fnic 62fbff0c42e7fb825c60a55cde2fb91facb2ed24]
kernel: fnic_isr_msix_wq_copy+0x2d/0x60 [fnic 62fbff0c42e7fb825c60a55cde2fb91facb2ed24]
kernel: __handle_irq_event_percpu+0x36/0x1a0
kernel: handle_irq_event_percpu+0x30/0x70
kernel: handle_irq_event+0x34/0x60
kernel: handle_edge_irq+0x7e/0x1a0
kernel: __common_interrupt+0x3b/0xb0
kernel: common_interrupt+0x58/0xa0
kernel: </IRQ>
It has been observed that this may break the rediscovery of Fibre
Channel devices after a temporary fabric failure.
This patch fixes it by moving the work queue initialization out of
an if block in fnic_probe().
Signed-off-by: Martin Wilck <mwilck@suse.com>
Fixes: 379a58caa199 ("scsi: fnic: Move fnic_fnic_flush_tx() to a work queue")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240930133014.71615-1-mwilck@suse.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace manual offset calculations for response_upiu and prd_table in
ufshcd_init_lrb() with pre-calculated offsets already stored in the
utp_transfer_req_desc structure. The pre-calculated offsets are set
differently in ufshcd_host_memory_configure() based on the
UFSHCD_QUIRK_PRDT_BYTE_GRAN quirk, ensuring correct alignment and
access.
Fixes: 26f968d7de82 ("scsi: ufs: Introduce UFSHCD_QUIRK_PRDT_BYTE_GRAN quirk")
Cc: stable@vger.kernel.org
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240910044543.3812642-1-avri.altman@wdc.com
Acked-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- Restore pci state on resume (Rodrigo Vivi)
- Fix locking on submission, queue and vm (Matthew Auld, Matthew Brost)
- Fix UAF on queue destruction (Matthew Auld)
- Fix resource release on freq init error path (He Lugang)
- Use rw_semaphore to reduce contention on ASID->VM lookup (Matthew Brost)
- Fix steering for media on Xe2_HPM (Gustavo Sousa)
- Tuning updates to Xe2 (Gustavo Sousa)
- Resume TDR after GT reset to prevent jobs running forever (Matthew Brost)
- Move id allocation to avoid userspace using a guessed number
to trigger UAF (Matthew Auld, Matthew Brost)
- Fix OA stream close preventing pbatch buffers to complete (José)
- Fix NPD when migrating memory on LNL (Zhanjun Dong)
- Fix memory leak when aborting binds (Matthew Brost)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2fiv63yanlal5mpw3mxtotte6yvkvtex74c7mkjxca4bazlyja@o4iejcfragxy
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-09-30 (ice, idpf)
This series contains updates to ice and idpf drivers:
For ice:
Michal corrects setting of dst VSI on LAN filters and adds clearing of
port VLAN configuration during reset.
Gui-Dong Han corrects failures to decrement refcount in some error
paths.
Przemek resolves a memory leak in ice_init_tx_topology().
Arkadiusz prevents setting of DPLL_PIN_STATE_SELECTABLE to an improper
value.
Dave stops clearing of VLAN tracking bit to allow for VLANs to be properly
restored after reset.
For idpf:
Ahmed sets uninitialized dyn_ctl_intrvl_s value.
Josh corrects use and reporting of mailbox size.
Larysa corrects order of function calls during de-initialization.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: deinit virtchnl transaction manager after vport and vectors
idpf: use actual mbx receive payload length
idpf: fix VF dynamic interrupt ctl register initialization
ice: fix VLAN replay after reset
ice: disallow DPLL_PIN_STATE_SELECTABLE for dpll output pins
ice: fix memleak in ice_init_tx_topology()
ice: clear port vlan config during reset
ice: Fix improper handling of refcount in ice_sriov_set_msix_vec_count()
ice: Fix improper handling of refcount in ice_dpll_init_rclk_pins()
ice: set correct dst VSI in only LAN filters
====================
Link: https://patch.msgid.link/20240930223601.3137464-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the use of phy_set_max_speed in phy driver as the
function is mainly used in MAC driver to set the max
speed.
Instead use get_features to fix up Phy PMA capabilities for
AQR111, AQR111B0, AQR114C and AQCS109
Fixes: 038ba1dc4e54 ("net: phy: aquantia: add AQR111 and AQR111B0 PHY ID")
Fixes: 0974f1f03b07 ("net: phy: aquantia: remove false 5G and 10G speed ability for AQCS109")
Fixes: c278ec644377 ("net: phy: aquantia: add support for AQR114C PHY ID")
Link: https://lore.kernel.org/all/20240913011635.1286027-1-quic_abchauha@quicinc.com/T/
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20241001224626.2400222-3-quic_abchauha@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
AQR115c reports incorrect PMA capabilities which includes
10G/5G and also incorrectly disables capabilities like autoneg
and 10Mbps support.
AQR115c as per the Marvell databook supports speeds up to 2.5Gbps
with autonegotiation.
Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c")
Link: https://lore.kernel.org/all/20240913011635.1286027-1-quic_abchauha@quicinc.com/T/
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20241001224626.2400222-2-quic_abchauha@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Yury reported a crash in the sfc driver originated from
netpoll_send_udp(). The netconsole sends a message and then netpoll
invokes the driver's NAPI function with a budget of zero. It is
dedicated to allow driver to free TX resources, that it may have used
while sending the packet.
In the netpoll case the driver invokes xdp_do_flush() unconditionally,
leading to crash because bpf_net_context was never assigned.
Invoke xdp_do_flush() only if budget is not zero.
Fixes: 401cb7dae8130 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
Reported-by: Yury Vostrikov <mon@unformed.ru>
Closes: https://lore.kernel.org/5627f6d1-5491-4462-9d75-bc0612c26a22@app.fastmail.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20241002125837.utOcRo6Y@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When configuring the fiber port, the DP83869 PHY driver incorrectly
calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit
number (10). This corrupts some other memory location -- in case of
arm64 the priv pointer in the same structure.
Since the advertising flags are updated from supported at the end of the
function the incorrect line isn't needed at all and can be removed.
Fixes: a29de52ba2a1 ("net: dp83869: Add ability to advertise Fiber connection")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241002161807.440378-1-inguin@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mutex field has two following semicolons, replace this with just
one semicolon.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240917120856.1877733-1-colin.i.king@gmail.com
|
|
Push regular plane/color management updates to the DSB,
if other constraints allow it.
The first part of the sequence will go as follows:
- CPU will kick off DSB0 immediately
- DSB0 writes double bufferd non-arming registers
- DSB0 evades the vblank
- DSB0 writes double buffered arming registers
If no color management updates is needed we follow that up with:
- DSB0 waits for the undelayed vblank
- DSB0 waits for the delayed vblank (usec wait)
- DSB0 emits an interrupt which will cause the CPU to complete the commit
If color management update is needed:
- DSB0 will start DSB1 with wait for undelayed vblank
- DSB0 will in parallel perform the force DEwake tricks
- DSB1 writes single buffered LUT registers
- DSB1 waits for the delayed vblank (usec wait)
- DSB1 emits an interrupt which will cause the CPU to complete the commit
With this sequence we don't need to increase the vblank delay
to make room for register programming during vblank, which is
a good thing for high refresh rate display. But I'll need to
still think of some way to eliminate VRR commit completion
related races under this scheme.
Stuff that isn't ready for DSB yet:
- modesets (potentially we could do
at least the plane enabling via DSB)
- fastsets
- VRR
- PSR
- scalers
- async flips
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-14-ville.syrjala@linux.intel.com
|
|
Pass the 'dsb' all the way down to the color commit hooks so that
we'll be able to update the double buffered color management registers
(eg. CSC) via the DSB.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-13-ville.syrjala@linux.intel.com
|
|
We need to be able to do both MMIO and DSB based pipe/plane
programming. To that end plumb the 'dsb' all way from the top
into the plane commit hooks.
The compiler appears smart enough to combine the branches from
all the back-to-back register writes into a single branch.
So the generated asm ends up looking more or less like this:
plane_hook()
{
if (dsb) {
intel_dsb_reg_write();
intel_dsb_reg_write();
...
} else {
intel_de_write_fw();
intel_de_write_fw();
...
}
}
which seems like a reasonably efficient way to do this.
An alternative I was also considering is some kind of closure
(register write function + display vs. dsb pointer passed to it).
That does result is smaller code as there are no branches anymore,
but having each register access go via function pointer sounds
less efficient.
Not that I actually measured the overhead of either approach yet.
Also the reg_rw tracepoint seems to be making a huge mess of the
generated code for the mmio path. And additionally there's some
kind of IS_GSI_REG() hack in __raw_uncore_read() which ends up
generating a pointless branch for every mmio register access.
So looks like there might be quite a bit of room for improvement
in the mmio path still.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-12-ville.syrjala@linux.intel.com
|
|
Extract the code for staging the vblank event for the
flip done interrupt handler. We'll reuse this for DSB
stuff later.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-11-ville.syrjala@linux.intel.com
|
|
Add intel_dsb_wait_vblank_delay() which instructs the DSB
to wait for duration between the undelayed and delayed vblanks.
We'll need this as the DSB can only directly wait for the
undelayed vblank, but we'll need to wait until the delayed
vblank has elapsed as well.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-10-ville.syrjala@linux.intel.com
|
|
Introduce intel_scanlines_to_usecs() as a counterpart to
intel_usecs_to_scanlines().
We'll have some use for this in DSB code as we want to do
relative scanline waits to evade the delayed vblank, but
unfortunately DSB can't do relative scanline waits (only
absolute). So we'll instead convert the relative scanline
count to usec and do a relative usec wait instead (which the
DSB knows how to do).
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-9-ville.syrjala@linux.intel.com
|
|
Add a function to emit a DSB wait for vblank instruction. This
just waits until the specified number of vblanks.
Note that this triggers on the transcoder's undelayed vblank,
as opposed to the pipe's delayed vblank.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-8-ville.syrjala@linux.intel.com
|
|
Add a function to emit the DSB "wait usecs" instruction.
This is just a usleep() for the DSB.
As a lower bound it seems pretty accurate, but the upper bound
seemed oddly relaxed (ie. sometimes I've seen waits that are
quite a bit longer than specified, not sure why).
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-7-ville.syrjala@linux.intel.com
|
|
Add a helper for performing vblank evasion on the DSB. DSB based
plane updates will need this to guarantee all the double buffered
arming registers will get programmed atomically within the same
frame.
With VRR we more or less have two vblanks to worry about:
- vmax vblank start in case no push was sent
- vmin vblank start in case a push was already sent during
the vertical active. Only a concern for mailbox updates,
which I suppose could happen if the legacy cursor updates
take the non-fastpath without setting
state->legacy_cursor_update to false.
Since we don't know which case is relevant we'll just evade
both.
We must also make sure to evade both the delayed vblank
(for pipe/plane registers) and the undelayed vblank
(for transcoder registers and chained DSBs w/
DSB_WAIT_FOR_VBLANK).
TODO: come up with a sensible usec number for the evasion...
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-6-ville.syrjala@linux.intel.com
|
|
The DSB can signal a programmable interrupt in response to
a specific DSB command getting executed. Hook that up.
For now we'll just use this to signal the completion of the
commit via a vblank event. If, in the future, we'll need to
do other things in response to DSB interrupts we may need to
come up with some kind of fancier DSB interrupt framework where
the caller can specify a custom handler...
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-5-ville.syrjala@linux.intel.com
|
|
Once we start using DSB for plane updates we'll need to defer
generating the DSB buffer until the clear color has been
read out. So we need to move at some of the DSB stuff into
commit_tail(). That is perhaps a better place for it anyway
as the ioctl thread can move on immediately without spending
time building the DSB commands.
We always have the MMIO fallback (in case the DSB buffer
allocation fails), so there's no real reason to keep any
of this in the synchronous part of the ioctl.
Because the DSB LUT programming doesn't depend on the plane
clear color we can still do that part before waiting for
fences/etc. which should help paralleize things a bit more.
The DSB plane programming will need to happen after those
however as that depends on the clear color.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-4-ville.syrjala@linux.intel.com
|
|
Read out the clear color as soon as fences and the transient
data flush have finished. There is no need to wait for
all the display specific operations that might still be
going on. This could parallelize things a bit more effectively.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-3-ville.syrjala@linux.intel.com
|
|
Reading from the DSB command buffer might be somewhat expensive on
discrete GPUs because the buffer resides in GPU local memory. Avoid
such reads in the indexed register write handling by tracking the
previous instruction in intel_dsb.
TODO: actually measure this
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930170415.23841-2-ville.syrjala@linux.intel.com
|
|
The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 11feaef69d0c ("drm/bridge: it6505: Add caching for EDID")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-3-treapking@chromium.org
|
|
The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 8bdfc5dae4e3 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-2-treapking@chromium.org
|
|
Commit 76d54bf20cdc ("nvme-tcp: don't access released socket during
error recovery") added a mutex_lock() call for the queue->queue_lock
in nvme_tcp_get_address(). However, the mutex_lock() races with
mutex_destroy() in nvme_tcp_free_queue(), and causes the WARN below.
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 3 PID: 34077 at kernel/locking/mutex.c:587 __mutex_lock+0xcf0/0x1220
Modules linked in: nvmet_tcp nvmet nvme_tcp nvme_fabrics iw_cm ib_cm ib_core pktcdvd nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables qrtr sunrpc ppdev 9pnet_virtio 9pnet pcspkr netfs parport_pc parport e1000 i2c_piix4 i2c_smbus loop fuse nfnetlink zram bochs drm_vram_helper drm_ttm_helper ttm drm_kms_helper xfs drm sym53c8xx floppy nvme scsi_transport_spi nvme_core nvme_auth serio_raw ata_generic pata_acpi dm_multipath qemu_fw_cfg [last unloaded: ib_uverbs]
CPU: 3 UID: 0 PID: 34077 Comm: udisksd Not tainted 6.11.0-rc7 #319
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
RIP: 0010:__mutex_lock+0xcf0/0x1220
Code: 08 84 d2 0f 85 c8 04 00 00 8b 15 ef b6 c8 01 85 d2 0f 85 78 f4 ff ff 48 c7 c6 20 93 ee af 48 c7 c7 60 91 ee af e8 f0 a7 6d fd <0f> 0b e9 5e f4 ff ff 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1
RSP: 0018:ffff88811305f760 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff88812c652058 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000001
RBP: ffff88811305f8b0 R08: 0000000000000001 R09: ffffed1075c36341
R10: ffff8883ae1b1a0b R11: 0000000000010498 R12: 0000000000000000
R13: 0000000000000000 R14: dffffc0000000000 R15: ffff88812c652058
FS: 00007f9713ae4980(0000) GS:ffff8883ae180000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fcd78483c7c CR3: 0000000122c38000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? __warn.cold+0x5b/0x1af
? __mutex_lock+0xcf0/0x1220
? report_bug+0x1ec/0x390
? handle_bug+0x3c/0x80
? exc_invalid_op+0x13/0x40
? asm_exc_invalid_op+0x16/0x20
? __mutex_lock+0xcf0/0x1220
? nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp]
? __pfx___mutex_lock+0x10/0x10
? __lock_acquire+0xd6a/0x59e0
? nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp]
nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp]
? __pfx_nvme_tcp_get_address+0x10/0x10 [nvme_tcp]
nvme_sysfs_show_address+0x81/0xc0 [nvme_core]
dev_attr_show+0x42/0x80
? __asan_memset+0x1f/0x40
sysfs_kf_seq_show+0x1f0/0x370
seq_read_iter+0x2cb/0x1130
? rw_verify_area+0x3b1/0x590
? __mutex_lock+0x433/0x1220
vfs_read+0x6a6/0xa20
? lockdep_hardirqs_on+0x78/0x100
? __pfx_vfs_read+0x10/0x10
ksys_read+0xf7/0x1d0
? __pfx_ksys_read+0x10/0x10
? __x64_sys_openat+0x105/0x1d0
do_syscall_64+0x93/0x180
? lockdep_hardirqs_on_prepare+0x16d/0x400
? do_syscall_64+0x9f/0x180
? lockdep_hardirqs_on+0x78/0x100
? do_syscall_64+0x9f/0x180
? __pfx_ksys_read+0x10/0x10
? lockdep_hardirqs_on_prepare+0x16d/0x400
? do_syscall_64+0x9f/0x180
? lockdep_hardirqs_on+0x78/0x100
? do_syscall_64+0x9f/0x180
? lockdep_hardirqs_on_prepare+0x16d/0x400
? do_syscall_64+0x9f/0x180
? lockdep_hardirqs_on+0x78/0x100
? do_syscall_64+0x9f/0x180
? lockdep_hardirqs_on_prepare+0x16d/0x400
? do_syscall_64+0x9f/0x180
? lockdep_hardirqs_on+0x78/0x100
? do_syscall_64+0x9f/0x180
? lockdep_hardirqs_on_prepare+0x16d/0x400
? do_syscall_64+0x9f/0x180
? lockdep_hardirqs_on+0x78/0x100
? do_syscall_64+0x9f/0x180
? do_syscall_64+0x9f/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f9713f55cfa
Code: 55 48 89 e5 48 83 ec 20 48 89 55 e8 48 89 75 f0 89 7d f8 e8 e8 74 f8 ff 48 8b 55 e8 48 8b 75 f0 41 89 c0 8b 7d f8 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 2e 44 89 c7 48 89 45 f8 e8 42 75 f8 ff 48 8b
RSP: 002b:00007ffd7f512e70 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
RAX: ffffffffffffffda RBX: 000055c38f316859 RCX: 00007f9713f55cfa
RDX: 0000000000000fff RSI: 00007ffd7f512eb0 RDI: 0000000000000011
RBP: 00007ffd7f512e90 R08: 0000000000000000 R09: 00000000ffffffff
R10: 0000000000000000 R11: 0000000000000246 R12: 000055c38f317148
R13: 0000000000000000 R14: 00007f96f4004f30 R15: 000055c3b6b623c0
</TASK>
The WARN is observed when the blktests test case nvme/014 is repeated
with tcp transport. It is rare, and 200 times repeat is required to
recreate in some test environments.
To avoid the WARN, check the NVME_TCP_Q_LIVE flag before locking
queue->queue_lock. The flag is cleared long time before the lock gets
destroyed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
In `gpiod_get_label()`, it is possible that `srcu_dereference_check()` may
return a NULL pointer, leading to a scenario where `label->str` is accessed
without verifying if `label` itself is NULL.
This patch adds a proper NULL check for `label` before accessing
`label->str`. The check for `label->str != NULL` is removed because
`label->str` can never be NULL if `label` is not NULL.
This fixes the issue where the label name was being printed as `(efault)`
when dumping the sysfs GPIO file when `label == NULL`.
Fixes: 5a646e03e956 ("gpiolib: Return label, if set, for IRQ only line")
Fixes: a86d27693066 ("gpiolib: fix the speed of descriptor label setting with SRCU")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241003131351.472015-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
As part of a Wa_22019338487, ensure that GT freq is restored
even when GSC reload is not successful.
Fixes: 3b1592fb7835 ("drm/xe/lnl: Apply Wa_22019338487")
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240925204918.1989574-1-vinay.belgaumkar@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The goal is to clean-up Linux repository from AUX file names, because
the use of such file names is prohibited on other operating systems
such as Windows, so the Linux repository cannot be cloned and
edited on them.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu>
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240603091558.35672-1-egyszeregy@freemail.hu
|
