| Age | Commit message (Collapse) | Author |
|---|
|
Remove a spurious 'b' in the "contiguous chunk is too small %lu/%lu b"
message.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
VP9 bitstream specification indicate segment data should reset to
default when meet key frames, intra only frames or enable error
resilience mode. So memset segmentation map buffer before every
decode process is not appropriate.
Reset segment data only when needed, then start decoder hardware
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Josef reported that his old-and-good Plextor ConvertX M402U video
converter spews lots of WARNINGs on the recent kernels, and it turned
out that the device uses a bulk endpoint for interrupt handling just
like 2250 board.
For fixing it, generalize the check with the proper verification of
the endpoint instead of hard-coded board type check.
Fixes: 7e5219d18e93 ("[media] go7007: Fix 2250 urb type")
Reported-and-tested-by: Josef Möllers <josef.moellers@suse.com>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1162583
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206427
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Allwinner A83T contains rotation core which can rotate and flip images.
Add a driver for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[hverkuil-cisco@xs4all.nl: MAINTAINERS paths were out of date, fix that]
[hverkuil-cisco@xs4all.nl: VFL_TYPE_GRABBER -> _VIDEO]
[hverkuil-cisco@xs4all.nl: Fix module build]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently, v4l2_pipeline_pm_use() prototype is:
int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
Where the 'use' argument shall only be set to '1' for enable/power-on,
or to '0' for disable/power-off. The integer return is specified
as only meaningful when 'use' is set to '1'.
Let's enforce this semantic by splitting the function in two:
v4l2_pipeline_pm_get and v4l2_pipeline_pm_put. This is done
for several reasons.
It makes the API easier to use (or harder to misuse).
It removes the constraint on the values the 'use' argument
shall take. Also, it removes the need to constraint
the return value, by making v4l2_pipeline_pm_put void return.
And last, it's more consistent with other kernel APIs, such
as the runtime pm APIs, which makes the code more symmetric.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The driver is deprecated and scheduled for removal by the end
of 2020. The reason is that this driver is for old and obsolete
hardware, and it produces a continuous stream of syzbot errors due
to poor code.
In order to prevent removal the following actions would have to
be taken:
- clean up the code
- convert to the vb2 framework
- fix the disconnect and free-on-last-user handling (i.e., add
a release callback for struct v4l2_device and rework the code
to use that correctly).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Three fixes to EFI mixed boot mode, mostly related to x86-64 vmap
stacks activated years ago, bug-fixed recently for EFI, which had
knock-on effects of various 1:1 mapping assumptions in mixed mode.
There's also a READ_ONCE() fix for reading an mmap-ed EFI firmware
data field only once, out of caution"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: READ_ONCE rng seed size before munmap
efi/x86: Handle by-ref arguments covering multiple pages in mixed mode
efi/x86: Remove support for EFI time and counter services in mixed mode
efi/x86: Align GUIDs to their size in the mixed mode runtime wrapper
|
|
Fix bogus NULL checks on the return value of acpi_cpu_get_madt_gicc()
by checking for a 0 'gicc->performance_interrupt' value instead.
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When disabling a counter from ddr_perf_event_stop(), the counter value
is reset to 0 at the same time.
Preserve the counter value by performing a read-modify-write of the
PMU register and clearing only the enable bit.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
If the boot EC comes from the DSDT, its ACPI handle is equal to the
handle of a device object with the PNP0C09 device ID. If that
device object is passed to acpi_ec_add(), it is not necessary to
allocate a new EC structure for it and parse it, because that has
been done already, so change the function to use the fast path in
that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
First, notice that if the device ID in acpi_ec_add() is equal to
ACPI_ECDT_HID, boot_ec_is_ecdt must be set, because this means
that the device object passed to acpi_ec_add() comes from
acpi_ec_ecdt_start() which fails if boot_ec_is_ecdt is unset.
Accordingly, boot_ec_is_ecdt need not be set again in that case,
so drop that redundant update of it from the code.
Next, ec->handle must be a valid ACPI handle right before
returning 0 from acpi_ec_add(), because it either is the handle
of the device object passed to that function, or it is the boot EC
handle coming from acpi_ec_ecdt_start() which fails if it cannot
find a valid handle for the boot EC. Moreover, the object with
that handle is regarded as a valid representation of the EC in all
cases, so there is no reason to avoid the _DEP list update walk if
that handle is the boot EC handle. Accordingly, drop the dep_update
local variable from acpi_ec_add() and call acpi_walk_dep_device_list()
for ec->handle unconditionally before returning 0 from it.
Finally, the ec local variable in acpi_ec_add() need not be
initialized to NULL and the status local variable declaration
can be moved to the block in which it is used, so change the code
in accordance with these observations.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The assert_mmap_offset() returns type bool so if we return an error
pointer that is "return true;" or success. If we have an error, then
we should return false.
Fixes: 3d81d589d6e3 ("drm/i915: Test exhaustion of the mmap space")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228141413.qfjf4abr323drlo4@kili.mountain
(cherry picked from commit efbf928824820f2738f41271934f6ec2c6ebd587)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
We need to be extremely careful inside i915_request_await_start() as it
needs to walk the list of requests in the foreign timeline with very
little protection. As we hold our own timeline mutex, we can not nest
inside the signaler's timeline mutex, so all that remains is our RCU
protection. However, to be safe we need to tell the compiler that we may
be traversing the list only under RCU protection, and furthermore we
need to start declaring requests as elements of the timeline from their
construction.
Fixes: 9ddc8ec027a3 ("drm/i915: Eliminate the trylock for awaiting an earlier request")
Fixes: 6a79d848403d ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-11-chris@chris-wilson.co.uk
(cherry picked from commit d22d2d073ef859b346bc32cb25299262e3973769)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Wa_1608008084 is an additional WA that applies to writes on FF_MODE2
register. We can't read it back either from CPU or GPU. Since the other
bits should be 0, recommendation to handle Wa_1604555607 is to actually
just write the timer value.
Do a write only and don't try to read it, neither before or after
the WA is applied.
Fixes: ff690b2111ba ("drm/i915/tgl: Implement Wa_1604555607")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224191258.15668-1-lucas.demarchi@intel.com
(cherry picked from commit e94bda14325ccf1a519ffb516738d1201457f97f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Slave demod needs some time to wake up otherwise it may not respond to the
following probe commands. This problem manifested randomly on my Astrometa
DVB-T2 dongle.
Signed-off-by: Mario Hros <git@reversity.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
We need to explicitly set the TLB Request Timer initial value in the
BW_BUDDY registers to 0x8 rather than relying on the hardware default.
v2: Apply missing REG_FIELD_PREP to ensure 0x8 is placed in the correct
bits during the rmw. (Jose)
Bspec: 52890
Bspec: 50044
Fixes: 3fa01d642fa7 ("drm/i915/tgl: Program BW_BUDDY registers during display init")
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200219215655.2923650-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 87e04f75928bb5d357ef7df4eedc1a7e2761a833)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228004320.127142-2-matthew.d.roper@intel.com
|
|
It wasn't terribly clear from the bspec's wording, but after discussion
with the hardware folks, it turns out that we need to preserve the
pre-existing contents of the MBUS ABOX control register when
initializing a few specific bits.
Bspec: 49213
Bspec: 50096
Fixes: 4cb4585e5a7f ("drm/i915/icl: initialize MBus during display init")
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204011032.582737-1-matthew.d.roper@intel.com
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
(cherry picked from commit 837b63e6087838d0f1e612d448405419199d8033)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228004320.127142-1-matthew.d.roper@intel.com
|
|
Commit 60c6a14b489b ("drm/i915/display: Force the state compute phase
once to enable PSR") was forcing the state compute too earlier
causing errors because not everything was initialized, so here
moving to the end of i915_driver_modeset_probe() when the display is
all initialized.
Also fixing the place where it disarm the force probe as during the
atomic check phase errors could happen like the ones due locking and
it would cause PSR to never be enabled if that happens.
Leaving the disarm to the atomic commit phase, intel_psr_enable() or
intel_psr_update() will be called even if the current state do not
allow PSR to be enabled.
v2: Check if intel_dp is null in intel_psr_force_mode_changed_set()
v3: Check intel_dp before get dev_priv
v4:
- renamed intel_psr_force_mode_changed_set() to
intel_psr_set_force_mode_changed()
- removed the set parameter from intel_psr_set_force_mode_changed()
- not calling intel_psr_set_force_mode_changed() from
intel_psr_enable/update(), directly setting it after the same checks
that intel_psr_set_force_mode_changed() does
- moved intel_psr_set_force_mode_changed() arm call to
i915_driver_modeset_probe() as it is a better for a PSR call, all the
functions calls happening between the old and the new function call
will cause issue
[backported to v5.6-rc3]
Fixes: 60c6a14b489b ("drm/i915/display: Force the state compute phase once to enable PSR")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1151
Tested-by: Ross Zwisler <zwisler@google.com>
Reported-by: Ross Zwisler <zwisler@google.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221212635.11614-1-jose.souza@intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20200227205540.126135-1-jose.souza@intel.com
(cherry picked from commit df1a5bfc16f3275a74f77d73375e69bc62c45c4b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Call cond_resched() between each freed object in case we have a really,
really long list, and we don't want to block normal processes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221100953.2587176-1-chris@chris-wilson.co.uk
(cherry picked from commit deeee411a97559096523f97655ff16da34cf0573)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Was added by commit 95cf9264d5f3 ("x86, drm, fbdev: Do not specify
encrypted memory for video mappings"), then it was kept through various
changes.
While vram actually needs decrypted mappings this is not correct for
shmem gem objects which live in main memory not io memory, so remove the
call.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200228104723.18757-1-kraxel@redhat.com
|
|
Move enabling and disabling HDMI_EN optional regulator to probe() function
to keep track on the regulator status. This fixes following warning if
probe() fails (for example when I2C DDC adapter cannot be yet gathered
due to the missing driver). This fixes following warning observed on
Arndale5250 board with multi_v7_defconfig:
[drm] Failed to get ddc i2c adapter by node
------------[ cut here ]------------
WARNING: CPU: 0 PID: 214 at drivers/regulator/core.c:2051 _regulator_put+0x16c/0x184
Modules linked in: ...
CPU: 0 PID: 214 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200219-00040-g38af1dfafdbb #7570
Hardware name: Samsung Exynos (Flattened Device Tree)
[<c0312258>] (unwind_backtrace) from [<c030cc10>] (show_stack+0x10/0x14)
[<c030cc10>] (show_stack) from [<c0f0d3a0>] (dump_stack+0xcc/0xe0)
[<c0f0d3a0>] (dump_stack) from [<c0346a58>] (__warn+0xe0/0xf8)
[<c0346a58>] (__warn) from [<c0346b20>] (warn_slowpath_fmt+0xb0/0xb8)
[<c0346b20>] (warn_slowpath_fmt) from [<c0893f58>] (_regulator_put+0x16c/0x184)
[<c0893f58>] (_regulator_put) from [<c0893f8c>] (regulator_put+0x1c/0x2c)
[<c0893f8c>] (regulator_put) from [<c09b2664>] (release_nodes+0x17c/0x200)
[<c09b2664>] (release_nodes) from [<c09aebe8>] (really_probe+0x10c/0x350)
[<c09aebe8>] (really_probe) from [<c09aefa8>] (driver_probe_device+0x60/0x1a0)
[<c09aefa8>] (driver_probe_device) from [<c09af288>] (device_driver_attach+0x58/0x60)
[<c09af288>] (device_driver_attach) from [<c09af310>] (__driver_attach+0x80/0xbc)
[<c09af310>] (__driver_attach) from [<c09ace34>] (bus_for_each_dev+0x68/0xb4)
[<c09ace34>] (bus_for_each_dev) from [<c09ae00c>] (bus_add_driver+0x130/0x1e8)
[<c09ae00c>] (bus_add_driver) from [<c09afd98>] (driver_register+0x78/0x110)
[<c09afd98>] (driver_register) from [<bf139558>] (exynos_drm_init+0xe8/0x11c [exynosdrm])
[<bf139558>] (exynos_drm_init [exynosdrm]) from [<c0302fa8>] (do_one_initcall+0x50/0x220)
[<c0302fa8>] (do_one_initcall) from [<c03dc02c>] (do_init_module+0x60/0x210)
[<c03dc02c>] (do_init_module) from [<c03daf44>] (load_module+0x1c0c/0x2310)
[<c03daf44>] (load_module) from [<c03db85c>] (sys_finit_module+0xac/0xbc)
[<c03db85c>] (sys_finit_module) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xecca3fa8 to 0xecca3ff0)
...
---[ end trace 276c91214635905c ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Writing to the built-in strings arrays doesn't work if driver is loaded
as kernel module. This is also considered as a bad pattern. Fix this by
adding a call to clk_get() with legacy clock name. This fixes following
kernel oops if driver is loaded as module:
Unable to handle kernel paging request at virtual address bf047978
pgd = (ptrval)
[bf047978] *pgd=59344811, *pte=5903c6df, *ppte=5903c65f
Internal error: Oops: 80f [#1] SMP ARM
Modules linked in: mc exynosdrm(+) analogix_dp rtc_s3c exynos_ppmu i2c_gpio
CPU: 1 PID: 212 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200219 #326
videodev: Linux video capture interface: v2.00
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at exynos_dsi_probe+0x1f0/0x384 [exynosdrm]
LR is at exynos_dsi_probe+0x1dc/0x384 [exynosdrm]
...
Process systemd-udevd (pid: 212, stack limit = 0x(ptrval))
...
[<bf03cf14>] (exynos_dsi_probe [exynosdrm]) from [<c09b1ca0>] (platform_drv_probe+0x6c/0xa4)
[<c09b1ca0>] (platform_drv_probe) from [<c09afcb8>] (really_probe+0x210/0x350)
[<c09afcb8>] (really_probe) from [<c09aff74>] (driver_probe_device+0x60/0x1a0)
[<c09aff74>] (driver_probe_device) from [<c09b0254>] (device_driver_attach+0x58/0x60)
[<c09b0254>] (device_driver_attach) from [<c09b02dc>] (__driver_attach+0x80/0xbc)
[<c09b02dc>] (__driver_attach) from [<c09ade00>] (bus_for_each_dev+0x68/0xb4)
[<c09ade00>] (bus_for_each_dev) from [<c09aefd8>] (bus_add_driver+0x130/0x1e8)
[<c09aefd8>] (bus_add_driver) from [<c09b0d64>] (driver_register+0x78/0x110)
[<c09b0d64>] (driver_register) from [<bf038558>] (exynos_drm_init+0xe8/0x11c [exynosdrm])
[<bf038558>] (exynos_drm_init [exynosdrm]) from [<c0302fa8>] (do_one_initcall+0x50/0x220)
[<c0302fa8>] (do_one_initcall) from [<c03dd02c>] (do_init_module+0x60/0x210)
[<c03dd02c>] (do_init_module) from [<c03dbf44>] (load_module+0x1c0c/0x2310)
[<c03dbf44>] (load_module) from [<c03dc85c>] (sys_finit_module+0xac/0xbc)
[<c03dc85c>] (sys_finit_module) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xd979bfa8 to 0xd979bff0)
...
---[ end trace db16efe05faab470 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Properly propagate error value from devm_regulator_bulk_get() and don't
confuse user with meaningless warning about failure in getting regulators
in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
After bnxt_hwrm_do_send_message() was updated to return standard error
codes in a recent commit, a regression in bnxt_flash_package_from_file()
was introduced. The return value does not properly reflect all
possible firmware errors when calling firmware to flash the package.
Fix it by consolidating all errors in one local variable rc instead
of having 2 variables for different errors.
Fixes: d4f1420d3656 ("bnxt_en: Convert error code in firmware message response to standard code.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MTU changes may affect the number of IRQs so we must call
bnxt_close_nic()/bnxt_open_nic() with the irq_re_init parameter
set to true. The reason is that a larger MTU may require
aggregation rings not needed with smaller MTU. We may not be
able to allocate the required number of aggregation rings and
so we reduce the number of channels which will change the number
of IRQs. Without this patch, it may crash eventually in
pci_disable_msix() when the IRQs are not properly unwound.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On all PHY drivers that implement did_interrupt() reading the interrupt
status bits clears them. This means we may loose an interrupt that
is triggered between calling did_interrupt() and phy_clear_interrupt().
As part of the fix make it a requirement that did_interrupt() clears
the interrupt.
The Fixes tag refers to the first commit where the patch applies
cleanly.
Fixes: 49644e68f472 ("net: phy: add callback for custom interrupt handler to struct phy_driver")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following NULL pointer dereference on PHY connect error path
teardown:
[ 2.291010] sja1105 spi0.1: Probed switch chip: SJA1105T
[ 2.310044] sja1105 spi0.1: Enabled switch tagging
[ 2.314970] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[ 2.322463] 8<--- cut here ---
[ 2.325497] Unable to handle kernel NULL pointer dereference at virtual address 00000018
[ 2.333555] pgd = (ptrval)
[ 2.336241] [00000018] *pgd=00000000
[ 2.339797] Internal error: Oops: 5 [#1] SMP ARM
[ 2.344384] Modules linked in:
[ 2.347420] CPU: 1 PID: 64 Comm: kworker/1:1 Not tainted 5.5.0-rc5 #1
[ 2.353820] Hardware name: Freescale LS1021A
[ 2.358070] Workqueue: events deferred_probe_work_func
[ 2.363182] PC is at kthread_destroy_worker+0x4/0x74
[ 2.368117] LR is at sja1105_teardown+0x70/0xb4
[ 2.372617] pc : [<c036cdd4>] lr : [<c0b89238>] psr: 60000013
[ 2.378845] sp : eeac3d30 ip : eeab1900 fp : eef45480
[ 2.384036] r10: eef4549c r9 : 00000001 r8 : 00000000
[ 2.389227] r7 : eef527c0 r6 : 00000034 r5 : ed8ddd0c r4 : ed8ddc40
[ 2.395714] r3 : 00000000 r2 : 00000000 r1 : eef4549c r0 : 00000000
[ 2.402204] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 2.409297] Control: 10c5387d Table: 8020406a DAC: 00000051
[ 2.415008] Process kworker/1:1 (pid: 64, stack limit = 0x(ptrval))
[ 2.421237] Stack: (0xeeac3d30 to 0xeeac4000)
[ 2.612635] [<c036cdd4>] (kthread_destroy_worker) from [<c0b89238>] (sja1105_teardown+0x70/0xb4)
[ 2.621379] [<c0b89238>] (sja1105_teardown) from [<c10717fc>] (dsa_switch_teardown.part.1+0x48/0x74)
[ 2.630467] [<c10717fc>] (dsa_switch_teardown.part.1) from [<c1072438>] (dsa_register_switch+0x8b0/0xbf4)
[ 2.639984] [<c1072438>] (dsa_register_switch) from [<c0b89c30>] (sja1105_probe+0x2ac/0x464)
[ 2.648378] [<c0b89c30>] (sja1105_probe) from [<c0b11a5c>] (spi_drv_probe+0x7c/0xa0)
[ 2.656081] [<c0b11a5c>] (spi_drv_probe) from [<c0a26ab8>] (really_probe+0x208/0x480)
[ 2.663871] [<c0a26ab8>] (really_probe) from [<c0a26f0c>] (driver_probe_device+0x78/0x1c4)
[ 2.672093] [<c0a26f0c>] (driver_probe_device) from [<c0a24c48>] (bus_for_each_drv+0x80/0xc4)
[ 2.680574] [<c0a24c48>] (bus_for_each_drv) from [<c0a26810>] (__device_attach+0xd0/0x168)
[ 2.688794] [<c0a26810>] (__device_attach) from [<c0a259d8>] (bus_probe_device+0x84/0x8c)
[ 2.696927] [<c0a259d8>] (bus_probe_device) from [<c0a25f24>] (deferred_probe_work_func+0x84/0xc4)
[ 2.705842] [<c0a25f24>] (deferred_probe_work_func) from [<c03667b0>] (process_one_work+0x22c/0x560)
[ 2.714926] [<c03667b0>] (process_one_work) from [<c0366d8c>] (worker_thread+0x2a8/0x5d4)
[ 2.723059] [<c0366d8c>] (worker_thread) from [<c036cf94>] (kthread+0x150/0x154)
[ 2.730416] [<c036cf94>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
Checking for NULL pointer is correct because the per-port xmit kernel
threads are created in sja1105_probe immediately after calling
dsa_register_switch.
Fixes: a68578c20a96 ("net: dsa: Make deferred_xmit private to sja1105")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the switch is not hardware reset on a warm boot, interrupts can be
left enabled, and possibly pending. This will cause us to enter an
infinite loop trying to service an interrupt we are unable to handle,
thereby preventing the kernel from booting.
Ensure that the global 2 interrupt sources are disabled before we claim
the parent interrupt.
Observed on the ZII development revision B and C platforms with
reworked serdes support, and using reboot -f to reboot the platform.
Fixes: dc30c35be720 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When debugging via PRINTK() is not enabled, make the PRINTK()
macro be an empty do-while block.
Thix fixes a gcc warning when -Wextra is set:
../drivers/atm/nicstar.c:1819:23: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
I have verified that there is no object code change (with gcc 7.5.0).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chas Williams <3chas3@gmail.com>
Cc: linux-atm-general@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
|__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.
When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:
[ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
[ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
[ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
[ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
[ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
This happens in, for example, r8153_init:
static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
void *data, u16 type)
{
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return -ENODEV;
...
}
static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
{
u32 data;
...
generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);
data = __le32_to_cpu(tmp);
...
return (u16)data;
}
static void r8153_init(struct r8152 *tp)
{
...
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return;
for (i = 0; i < 500; i++) {
if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
AUTOLOAD_DONE)
break;
msleep(20);
}
...
}
Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.
To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.
This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.
Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has three driver bugfixes for you. We agreed on the Mac regression
to go in via I2C"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
macintosh: therm_windtunnel: fix regression when instantiating devices
i2c: altera: Fix potential integer overflow
i2c: jz4780: silence log flood on txabrt
|
|
Removing attach_adapter from this driver caused a regression for at
least some machines. Those machines had the sensors described in their
DT, too, so they didn't need manual creation of the sensor devices. The
old code worked, though, because manual creation came first. Creation of
DT devices then failed later and caused error logs, but the sensors
worked nonetheless because of the manually created devices.
When removing attach_adaper, manual creation now comes later and loses
the race. The sensor devices were already registered via DT, yet with
another binding, so the driver could not be bound to it.
This fix refactors the code to remove the race and only manually creates
devices if there are no DT nodes present. Also, the DT binding is updated
to match both, the DT and manually created devices. Because we don't
know which device creation will be used at runtime, the code to start
the kthread is moved to do_probe() which will be called by both methods.
Fixes: 3e7bed52719d ("macintosh: therm_windtunnel: drop using attach_adapter")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201723
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Tested-by: Erhard Furtner <erhard_f@mailbox.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org # v4.19+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few fixes for omaps for v5.6-rc cycle
This series of changes contains few code fixes for issues
recently discovered:
- A build fix for ARMv6 only configs when CONFIG_HAVE_ARM_SMCCC is
not set
- A fix for ti-sysc quirk handling for 1-wire hdq reset
And a handful of dts fixes that I had queued up and should
have already sent earlier instead of waiting for the code
fixes to get sorted out:
- Fix naming of vsys_3v3 regulator for dra7-evm
- Fix incorrect OPP node names for am437x-idk-evm
- Fix IPU1 mux clock parent source for dra7
- Add missing PWM property for dra7 timers 13 to 16
- Add missing dma-ranges for dra7 PCIe nodes
- Fix mmc3 max-frequency for dra76x
* tag 'omap-for-v5.6/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
arm: dts: dra76x: Fix mmc3 max-frequency
ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
bus: ti-sysc: Fix 1-wire reset quirk
ARM: dts: dra7-l4: mark timer13-16 as pwm capable
ARM: dts: dra7xx-clocks: Fixup IPU1 mux clock parent source
ARM: dts: am437x-idk-evm: Fix incorrect OPP node names
ARM: dts: dra7-evm: Rename evm_3v3 regulator to vsys_3v3
Link: https://lore.kernel.org/r/pull-1582903541-589933@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes.
Three are in drivers for fairly obvious bugs. The fourth is a set of
regressions introduced by the compat_ioctl changes because some of the
compat updates wrongly replaced .ioctl instead of .compat_ioctl"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: compat_ioctl: cdrom: Replace .ioctl with .compat_ioctl in four appropriate places
scsi: zfcp: fix wrong data and display format of SFP+ temperature
scsi: sd_sbc: Fix sd_zbc_report_zones()
scsi: libfc: free response frame from GPN_ID
|
|
Recent changes to the way we deal with EFI runtime services that
are marked as unsupported by the firmware resulted in a regression
for non-EFI boot. The problem is that all EFI runtime services are
marked as available by default, and any non-NULL checks on the EFI
service function pointers (which will be non-NULL even for runtime
services that are unsupported on an EFI boot) were replaced with
checks against the mask stored in efi.runtime_supported_mask.
When doing a non-EFI boot, this check against the mask will return
a false positive, given the fact that all runtime services are
marked as enabled by default. Since we dropped the non-NULL check
of the runtime service function pointer in favor of the mask check,
we will now unconditionally dereference the function pointer, even
if it is NULL, and go boom.
So let's ensure that the mask reflects reality on a non-EFI boot,
which is that all EFI runtime services are unsupported.
Reported-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20200228121408.9075-7-ardb@kernel.org
|
|
Shadowing variables is generally frowned upon.
Let's simply reuse the existing loop counter 'i' instead of shadowing it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20200223221324.156086-1-xypron.glpk@gmx.de
Link: https://lore.kernel.org/r/20200228121408.9075-4-ardb@kernel.org
|
|
When booting with SME active, EFI tables must be mapped unencrypted since
they were built by UEFI in unencrypted memory. Update the list of tables
to be checked during early_memremap() processing to account for the EFI
RNG seed table.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Link: https://lore.kernel.org/r/b64385fc13e5d7ad4b459216524f138e7879234f.1582662842.git.thomas.lendacky@amd.com
Link: https://lore.kernel.org/r/20200228121408.9075-3-ardb@kernel.org
|
|
pinctrl_register_mappings is called in the pdata case, however a call to
pinctrl_unregister_mappings is missing causing the mappings to be leaked
on driver unbind. Add the missing call to correct this issue.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154214.13916-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
kref_init starts with the reference count at 1, which will be balanced
by the pinctrl_put in pinctrl_unregister. The additional kref_get in
pinctrl_claim_hogs will increase this count to 2 and cause the hogs to
not get freed when pinctrl_unregister is called.
Fixes: 6118714275f0 ("pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154142.13860-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix build issue on 32-bit ARM with old compilers (Marek Szyprowski)
- Update MAINTAINERS for recent Cadence driver file move (Lukas
Bulwahn)
* tag 'pci-v5.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Correct Cadence PCI driver path
PCI: brcmstb: Fix build on 32bit ARM platforms with older compilers
|
|
Pull block fixes from Jens Axboe:
- Passthrough insertion fix (Ming)
- Kill off some unused arguments (John)
- blktrace RCU fix (Jan)
- Dead fields removal for null_blk (Dongli)
- NVMe polled IO fix (Bijan)
* tag 'block-5.6-2020-02-28' of git://git.kernel.dk/linux-block:
nvme-pci: Hold cq_poll_lock while completing CQEs
blk-mq: Remove some unused function arguments
null_blk: remove unused fields in 'nullb_cmd'
blktrace: Protect q->blk_trace with RCU
blk-mq: insert passthrough request into hctx->dispatch directly
|
|
Introduce is_mmp2_ssp() helper to be consistent with the rest
helper function to distinguish SSP type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200227162556.3152-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
quirks" from John Garry <john.garry@huawei.com>:
As discussed during the original HiSilicon v3xx SPI driver upstreaming,
currently there is no method for the ACPI SPI Serial Bus Connection
Resource Descriptor to define the data buswidth [0], [1].
So we can look to get the ACPI spec updated for this, and I have
submitted a proposal for a new feature here:
https://bugzilla.tianocore.org/show_bug.cgi?id=2557
However I am not sure how successful that will be.
In the meantime, as an alternate approach, this RFC proposes to allow the
SPI controller driver override the device buswidth. In this example,
the driver uses DMI quirks to discover the host machine and set the
buswidth override accordingly when the machine is known to support
dual or quad mode of operation.
I also have included a fix for dual and quad modes in the driver.
Comments welcome. thanks.
[0] https://lore.kernel.org/linux-mtd/20200109212842.GK3702@sirena.org.uk/
[1] https://uefi.org/sites/default/files/resources/ACPI_6_3_final_Jan30.pdf,
19.6.126
John Garry (3):
spi: Allow SPI controller override device buswidth
spi: HiSilicon v3xx: Properly set CMD_CONFIG for Dual/Quad modes
spi: HiSilicon v3xx: Use DMI quirk to set controller buswidth override
bits
drivers/spi/spi-hisi-sfc-v3xx.c | 99 ++++++++++++++++++++++++++++++++-
drivers/spi/spi.c | 4 +-
include/linux/spi/spi.h | 3 +
3 files changed, 104 insertions(+), 2 deletions(-)
--
2.17.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
|
|
When adjust_op_size is defined, len is never used. Move the len
computation where it's actually used.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200228160735.1565047-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Huawei D06 board (and variants) can support Quad mode of operation.
Since we have no current method in ACPI SPI bus device resource description
to describe this information, use DMI to detect the board, and set the
controller buswidth override bits.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-4-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The CMD_CONFIG register memory interface type field is not set configured
for Dual and Quad modes, so set appropriately.
This was not detected previously as we only ever operated in standard SPI
mode.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-3-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently ACPI firmware description for a SPI device does not have any
method to describe the data buswidth on the board.
So even through the controller and device may support higher modes than
standard SPI, it cannot be assumed that the board does - as such, that
device is limited to standard SPI in such a circumstance.
As a workaround, allow the controller driver supply buswidth override bits,
which are used inform the core code that the controller driver knows the
buswidth supported on that board for that device.
A host controller driver might know this info from DMI tables, for example.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-2-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The QSPI controller memory space is limited to 128MB:
0x9000_00000-0x9800_00000/0XD000_0000--0XD800_0000.
There are nor flashes that are bigger in size than the memory size
supported by the controller: Micron MT25QL02G (256 MB).
Check if the address exceeds the MMIO window size. An improvement
would be to add support for regular SPI mode and fall back to it
when the flash memories overrun the controller's memory space.
Fixes: 0e6aae08e9ae ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200228155437.1558219-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
