| Age | Commit message (Collapse) | Author |
|---|
|
inhibited
If an IRQ can be posted to a vCPU, but AVIC is currently inhibited on the
vCPU, go through the dance of "affining" the IRTE to the vCPU, but leave
the actual IRTE in remapped mode. KVM already handles the case where AVIC
is inhibited => uninhibited with posted IRQs (see avic_set_pi_irte_mode()),
but doesn't handle the scenario where a postable IRQ comes along while AVIC
is inhibited.
Link: https://lore.kernel.org/r/20250611224604.313496-45-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Now that setting vCPU affinity is guarded with ir_list_lock, i.e. now that
avic_physical_id_entry can be safely accessed, set the pCPU info
straight-away when setting vCPU affinity. Putting the IRTE into posted
mode, and then immediately updating the IRTE a second time if the target
vCPU is running is wasteful and confusing.
This also fixes a flaw where a posted IRQ that arrives between putting
the IRTE into guest_mode and setting the correct destination could cause
the IOMMU to ring the doorbell on the wrong pCPU.
Link: https://lore.kernel.org/r/20250611224604.313496-44-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Split the guts of amd_iommu_update_ga() to a dedicated helper so that the
logic can be shared with flows that put the IRTE into posted mode.
Opportunistically move amd_iommu_update_ga() and its new helper above
amd_iommu_activate_guest_mode() so that it's all co-located.
Link: https://lore.kernel.org/r/20250611224604.313496-43-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Infer whether or not a vCPU should be marked running from the validity of
the pCPU on which it is running. amd_iommu_update_ga() already skips the
IRTE update if the pCPU is invalid, i.e. passing %true for is_run with an
invalid pCPU would be a blatant and egregrious KVM bug.
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Link: https://lore.kernel.org/r/20250611224604.313496-42-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add a comment to amd_iommu_update_ga() to document what fields it can
safely modify without issuing an invalidation of the IRTE, and to explain
its role in keeping GA IRTEs up-to-date.
Per page 93 of the IOMMU spec dated Feb 2025:
When virtual interrupts are enabled by setting MMIO Offset 0018h[GAEn] and
IRTE[GuestMode=1], IRTE[IsRun], IRTE[Destination], and if present IRTE[GATag],
are not cached by the IOMMU. Modifications to these fields do not require an
invalidation of the Interrupt Remapping Table.
Link: https://lore.kernel.org/all/9b7ceea3-8c47-4383-ad9c-1a9bbdc9044a@oracle.com
Cc: Joao Martins <joao.m.martins@oracle.com>
Link: https://lore.kernel.org/r/20250611224604.313496-41-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Split the vcpu_data structure that serves as a handoff from KVM to IOMMU
drivers into vendor specific structures. Overloading a single structure
makes the code hard to read and maintain, is *very* misleading as it
suggests that mixing vendors is actually supported, and bastardizing
Intel's posted interrupt descriptor address when AMD's IOMMU already has
its own structure is quite unnecessary.
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Link: https://lore.kernel.org/r/20250611224604.313496-33-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Pass NULL to amd_ir_set_vcpu_affinity() to communicate "don't post to a
vCPU" now that there's no need to communicate information back to KVM
about the previous vCPU (KVM does its own tracking).
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Link: https://lore.kernel.org/r/20250611224604.313496-24-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Use vcpu_data.pi_desc_addr instead of amd_iommu_pi_data.base to get the
GA root pointer. KVM is the only source of amd_iommu_pi_data.base, and
KVM's one and only path for writing amd_iommu_pi_data.base computes the
exact same value for vcpu_data.pi_desc_addr and amd_iommu_pi_data.base,
and fills amd_iommu_pi_data.base if and only if vcpu_data.pi_desc_addr is
valid, i.e. amd_iommu_pi_data.base is fully redundant.
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Link: https://lore.kernel.org/r/20250611224604.313496-23-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Delete the amd_ir_data.prev_ga_tag field now that all usage is
superfluous.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Link: https://lore.kernel.org/r/20250611224604.313496-8-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Pass in the Linux IRQ associated with an IRQ bypass producer instead of
relying on the caller to set the field prior to registration, as there's
no benefit to relying on callers to do the right thing.
Take care to set producer->irq before __connect(), as KVM expects the IRQ
to be valid as soon as a connection is possible.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20250516230734.2564775-9-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Move ownership of IRQ bypass token tracking into irqbypass.ko, and
explicitly require callers to pass an eventfd_ctx structure instead of a
completely opaque token. Relying on producers and consumers to set the
token appropriately is error prone, and hiding the fact that the token must
be an eventfd_ctx pointer (for all intents and purposes) unnecessarily
obfuscates the code and makes it more brittle.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20250516230734.2564775-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
When unmapping a vLPI, WARN if nullifying vCPU affinity fails, not just if
failure occurs when freeing an ITE. If undoing vCPU affinity fails, then
odds are very good that vLPI state tracking has has gotten out of whack,
i.e. that KVM and the GIC disagree on the state of an IRQ/vLPI. At best,
inconsistent state means there is a lurking bug/flaw somewhere. At worst,
the inconsistency could eventually be fatal to the host, e.g. if an ITS
command fails because KVM's view of things doesn't match reality/hardware.
Note, only the call from kvm_arch_irq_bypass_del_producer() by way of
kvm_vgic_v4_unset_forwarding() doesn't already WARN. Common KVM's
kvm_irq_routing_update() WARNs if kvm_arch_update_irqfd_routing() fails.
For that path, if its_unmap_vlpi() fails in kvm_vgic_v4_unset_forwarding(),
the only possible causes are that the GIC doesn't have a v4 ITS (from
its_irq_set_vcpu_affinity()):
/* Need a v4 ITS */
if (!is_v4(its_dev->its))
return -EINVAL;
guard(raw_spinlock)(&its_dev->event_map.vlpi_lock);
/* Unmap request? */
if (!info)
return its_vlpi_unmap(d);
or that KVM has gotten out of sync with the GIC/ITS (from its_vlpi_unmap()):
if (!its_dev->event_map.vm || !irqd_is_forwarded_to_vcpu(d))
return -EINVAL;
All of the above failure scenarios are warnable offences, as they should
never occur absent a kernel/KVM bug.
Acked-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/all/aFWY2LTVIxz5rfhh@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fix from Joerg Roedel:
- Fix PTE size calculation for NVidia Tegra
* tag 'iommu-fixes-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommu/tegra: Fix incorrect size calculation
|
|
Pull block fixes from Jens Axboe:
- Fix for a deadlock on queue freeze with zoned writes
- Fix for zoned append emulation
- Two bio folio fixes, for sparsemem and for very large folios
- Fix for a performance regression introduced in 6.13 when plug
insertion was changed
- Fix for NVMe passthrough handling for polled IO
- Document the ublk auto registration feature
- loop lockdep warning fix
* tag 'block-6.16-20250614' of git://git.kernel.dk/linux:
nvme: always punt polled uring_cmd end_io work to task_work
Documentation: ublk: Separate UBLK_F_AUTO_BUF_REG fallback behavior sublists
block: Fix bvec_set_folio() for very large folios
bio: Fix bio_first_folio() for SPARSEMEM without VMEMMAP
block: use plug request list tail for one-shot backmerge attempt
block: don't use submit_bio_noacct_nocheck in blk_zone_wplug_bio_work
block: Clear BIO_EMULATES_ZONE_APPEND flag on BIO completion
ublk: document auto buffer registration(UBLK_F_AUTO_BUF_REG)
loop: move lo_set_size() out of queue freeze
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"9 hotfixes. 3 are cc:stable and the remainder address post-6.15 issues
or aren't considered necessary for -stable kernels. Only 4 are for MM"
* tag 'mm-hotfixes-stable-2025-06-13-21-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm: add mmap_prepare() compatibility layer for nested file systems
init: fix build warnings about export.h
MAINTAINERS: add Barry as a THP reviewer
drivers/rapidio/rio_cm.c: prevent possible heap overwrite
mm: close theoretical race where stale TLB entries could linger
mm/vma: reset VMA iterator on commit_merge() OOM failure
docs: proc: update VmFlags documentation in smaps
scatterlist: fix extraneous '@'-sign kernel-doc notation
selftests/mm: skip failed memfd setups in gup_longterm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"All fixes for drivers.
The core change in the error handler is simply to translate an ALUA
specific sense code into a retry the ALUA components can handle and
won't impact any other devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: error: alua: I/O errors for ALUA state transitions
scsi: storvsc: Increase the timeouts to storvsc_timeout
scsi: s390: zfcp: Ensure synchronous unit_add
scsi: iscsi: Fix incorrect error path labels for flashnode operations
scsi: mvsas: Fix typos in per-phy comments and SAS cmd port registers
scsi: core: ufs: Fix a hang in the error handler
|
|
Pull drm fixes from Dave Airlie:
"Quiet week, only two pull requests came my way, xe has a couple of
fixes and then a bunch of fixes across the board, vc4 probably fixes
the biggest problem:
vc4:
- Fix infinite EPROBE_DEFER loop in vc4 probing
amdxdna:
- Fix amdxdna firmware size
meson:
- modesetting fixes
sitronix:
- Kconfig fix for st7171-i2c
dma-buf:
- Fix -EBUSY WARN_ON_ONCE in dma-buf
udmabuf:
- Use dma_sync_sgtable_for_cpu in udmabuf
xe:
- Fix regression disallowing 64K SVM migration
- Use a bounce buffer for WA BB"
* tag 'drm-fixes-2025-06-14' of https://gitlab.freedesktop.org/drm/kernel:
drm/xe/lrc: Use a temporary buffer for WA BB
udmabuf: use sgtable-based scatterlist wrappers
dma-buf: fix compare in WARN_ON_ONCE
drm/sitronix: st7571-i2c: Select VIDEOMODE_HELPERS
drm/meson: fix more rounding issues with 59.94Hz modes
drm/meson: use vclk_freq instead of pixel_freq in debug print
drm/meson: fix debug log statement when setting the HDMI clocks
drm/vc4: fix infinite EPROBE_DEFER loop
drm/xe/svm: Fix regression disallowing 64K SVM migration
accel/amdxdna: Fix incorrect PSP firmware size
|
|
Currently NVMe uring_cmd completions will complete locally, if they are
polled. This is done because those completions are always invoked from
task context. And while that is true, there's no guarantee that it's
invoked under the right ring context, or even task. If someone does
NVMe passthrough via multiple threads and with a limited number of
poll queues, then ringA may find completions from ringB. For that case,
completing the request may not be sound.
Always just punt the passthrough completions via task_work, which will
redirect the completion, if needed.
Cc: stable@vger.kernel.org
Fixes: 585079b6e425 ("nvme: wire up async polling for io passthrough commands")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix an ACPI APEI error injection driver failure that started to
occur after switching it over to using a faux device, address an EC
driver issue related to invalid ECDT tables, clean up the usage of
mwait_idle_with_hints() in the ACPI PAD driver, add a new IRQ override
quirk, and fix a NULL pointer dereference related to nosmp:
- Update the faux device handling code in the driver core and address
an ACPI APEI error injection driver failure that started to occur
after switching it over to using a faux device on top of that (Dan
Williams)
- Update data types of variables passed as arguments to
mwait_idle_with_hints() in the ACPI PAD (processor aggregator
device) driver to match the function definition after recent
changes (Uros Bizjak)
- Fix a NULL pointer dereference in the ACPI CPPC library that occurs
when nosmp is passed to the kernel in the command line (Yunhui Cui)
- Ignore ECDT tables with an invalid ID string to prevent using an
incorrect GPE for signaling events on some systems (Armin Wolf)
- Add a new IRQ override quirk for MACHENIKE 16P (Wentao Guan)"
* tag 'acpi-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: resource: Use IRQ override on MACHENIKE 16P
ACPI: EC: Ignore ECDT tables with an invalid ID string
ACPI: CPPC: Fix NULL pointer dereference when nosmp is used
ACPI: PAD: Update arguments of mwait_idle_with_hints()
ACPI: APEI: EINJ: Do not fail einj_init() on faux_device_create() failure
driver core: faux: Quiet probe failures
driver core: faux: Suppress bind attributes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix the cpupower utility installation, fix up the recently added
Rust abstractions for cpufreq and OPP, restore the x86 update
eliminating mwait_play_dead_cpuid_hint() that has been reverted during
the 6.16 merge window along with preventing the failure caused by it
from happening, and clean up mwait_idle_with_hints() usage in
intel_idle:
- Implement CpuId Rust abstraction and use it to fix doctest failure
related to the recently introduced cpumask abstraction (Viresh
Kumar)
- Do minor cleanups in the `# Safety` sections for cpufreq
abstractions added recently (Viresh Kumar)
- Unbreak cpupower systemd service units installation on some systems
by adding a unitdir variable for specifying the location to install
them (Francesco Poli)
- Eliminate mwait_play_dead_cpuid_hint() again after reverting its
elimination during the 6.16 merge window due to a problem with
handling "dead" SMT siblings, but this time prevent leaving them in
C1 after initialization by taking them online and back offline when
a proper cpuidle driver for the platform has been registered
(Rafael Wysocki)
- Update data types of variables passed as arguments to
mwait_idle_with_hints() to match the function definition after
recent changes (Uros Bizjak)"
* tag 'pm-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
rust: cpu: Add CpuId::current() to retrieve current CPU ID
rust: Use CpuId in place of raw CPU numbers
rust: cpu: Introduce CpuId abstraction
intel_idle: Update arguments of mwait_idle_with_hints()
cpufreq: Convert `/// SAFETY` lines to `# Safety` sections
cpupower: split unitdir from libdir in Makefile
Reapply "x86/smp: Eliminate mwait_play_dead_cpuid_hint()"
ACPI: processor: Rescan "dead" SMT siblings during initialization
intel_idle: Rescan "dead" SMT siblings during initialization
x86/smp: PM/hibernate: Split arch_resume_nosmt()
intel_idle: Use subsys_initcall_sync() for initialization
|
|
Merge assorted ACPI updates for 6.16-rc2:
- Update data types of variables passed as arguments to
mwait_idle_with_hints() in the ACPI PAD (processor aggregator device)
driver to match the function definition after recent changes (Uros
Bizjak).
- Fix a NULL pointer dereference in the ACPI CPPC library that occurs
when nosmp is passed to the kernel in the command line (Yunhui Cui).
- Ignore ECDT tables with an invalid ID string to prevent using an
incorrect GPE for signaling events on some systems (Armin Wolf).
- Add a new IRQ override quirk for MACHENIKE 16P (Wentao Guan).
* acpi-pad:
ACPI: PAD: Update arguments of mwait_idle_with_hints()
* acpi-cppc:
ACPI: CPPC: Fix NULL pointer dereference when nosmp is used
* acpi-ec:
ACPI: EC: Ignore ECDT tables with an invalid ID string
* acpi-resource:
ACPI: resource: Use IRQ override on MACHENIKE 16P
|
|
Merge cpuidle updates for 6.16-rc2:
- Update data types of variables passed as arguments to
mwait_idle_with_hints() to match the function definition
after recent changes (Uros Bizjak).
- Eliminate mwait_play_dead_cpuid_hint() again after reverting its
elimination during the merge window due to a problem with handling
"dead" SMT siblings, but this time prevent leaving them in C1 after
initialization by taking them online and back offline when a proper
cpuidle driver for the platform has been registered (Rafael Wysocki).
* pm-cpuidle:
intel_idle: Update arguments of mwait_idle_with_hints()
Reapply "x86/smp: Eliminate mwait_play_dead_cpuid_hint()"
ACPI: processor: Rescan "dead" SMT siblings during initialization
intel_idle: Rescan "dead" SMT siblings during initialization
x86/smp: PM/hibernate: Split arch_resume_nosmt()
intel_idle: Use subsys_initcall_sync() for initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of driver specific fixes, most minor apart from the OMAP
ones which disable some recent performance optimisations in some
non-standard cases where we could start driving the bus incorrectly.
The change to the stm32-ospi driver to use the newer reset APIs is a
fix for interactions with other IP sharing the same reset line in some
SoCs"
* tag 'spi-fix-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-pci1xxxx: Drop MSI-X usage as unsupported by DMA engine
spi: stm32-ospi: clean up on error in probe()
spi: stm32-ospi: Make usage of reset_control_acquire/release() API
spi: offload: check offload ops existence before disabling the trigger
spi: spi-pci1xxxx: Fix error code in probe
spi: loongson: Fix build warnings about export.h
spi: omap2-mcspi: Disable multi-mode when the previous message kept CS asserted
spi: omap2-mcspi: Disable multi mode when CS should be kept asserted after message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"One minor fix for a leak in the DT parsing code in the max20086 driver"
* tag 'regulator-fix-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: max20086: Fix refcount leak in max20086_parse_regulators_dt()
|
|
This driver uses a mixture of ways to get the size of a PTE,
tegra_smmu_set_pde() did it as sizeof(*pd) which became wrong when pd
switched to a struct tegra_pd.
Switch pd back to a u32* in tegra_smmu_set_pde() so the sizeof(*pd)
returns 4.
Fixes: 50568f87d1e2 ("iommu/terga: Do not use struct page as the handle for as->pd memory")
Reported-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Closes: https://lore.kernel.org/all/62e7f7fe-6200-4e4f-ad42-d58ad272baa6@tecnico.ulisboa.pt/
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Link: https://lore.kernel.org/r/0-v1-da7b8b3d57eb+ce-iommu_terga_sizeof_jgg@nvidia.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Removes MSI-X from the interrupt request path, as the DMA engine used by
the SPI controller does not support MSI-X interrupts.
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Link: https://patch.msgid.link/20250612023059.71726-1-thangaraj.s@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
drm-misc-fixes for v6.16-rc2:
- Fix infinite EPROBE_DEFER loop in vc4 probing.
- Fix amdxdna firmware size.
- mode fixes for meson.
- Kconfig fix for st7171-i2c.
- Fix -EBUSY WARN_ON_ONCE in dma-buf
- Use dma_sync_sgtable_for_cpu in udmabuf.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/62c06195-8bc1-4dae-8777-e86d94e4d9d9@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
|
|
In case the BO is in iomem, we can't simply take the vaddr and write to
it. Instead, prepare a separate buffer that is later copied into io
memory. Right now it's just a few words that could be using
xe_map_write32(), but the intention is to grow the WA BB for other
uses.
Fixes: 617d824c5323 ("drm/xe: Add WA BB to capture active context utilization")
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://lore.kernel.org/r/20250604-wa-bb-fix-v1-1-0dfc5dafcef0@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit ef48715b2d3df17c060e23b9aa636af3d95652f8)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Another quick round of updates:
- revert mwifiex HT40 that was causing issues
- many ath10k/ath11k/ath12k fixes
- re-add some iwlwifi code I lost in a merge
- use kfree_sensitive() on an error path in cfg80211
* tag 'wireless-2025-06-12' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cfg80211: use kfree_sensitive() for connkeys cleanup
wifi: iwlwifi: fix merge damage related to iwl_pci_resume
Revert "wifi: mwifiex: Fix HT40 bandwidth issue."
wifi: ath12k: fix uaf in ath12k_core_init()
wifi: ath12k: Fix hal_reo_cmd_status kernel-doc
wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850
wifi: ath11k: validate ath11k_crypto_mode on top of ath11k_core_qmi_firmware_ready
wifi: ath11k: consistently use ath11k_mac_get_fw_stats()
wifi: ath11k: move locking outside of ath11k_mac_get_fw_stats()
wifi: ath11k: adjust unlock sequence in ath11k_update_stats_event()
wifi: ath11k: move some firmware stats related functions outside of debugfs
wifi: ath11k: don't wait when there is no vdev started
wifi: ath11k: don't use static variables in ath11k_debugfs_fw_stats_process()
wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
wil6210: fix support for sparrow chipsets
wifi: ath10k: Avoid vdev delete timeout when firmware is already down
ath10k: snoc: fix unbalanced IRQ enable in crash recovery
====================
Link: https://patch.msgid.link/20250612082519.11447-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netdevsim supports netpoll. Make sure we don't call napi_complete()
from it, since it may not be scheduled. Breno reports hitting a
warning in napi_complete_done():
WARNING: CPU: 14 PID: 104 at net/core/dev.c:6592 napi_complete_done+0x2cc/0x560
__napi_poll+0x2d8/0x3a0
handle_softirqs+0x1fe/0x710
This is presumably after netpoll stole the SCHED bit prematurely.
Reported-by: Breno Leitao <leitao@debian.org>
Fixes: 3762ec05a9fb ("netdevsim: add NAPI support")
Tested-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250611174643.2769263-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Check for if ida_alloc() or rhashtable_lookup_get_insert_fast() fails.
Fixes: 17e0accac577 ("net/mlx5: HWS, support complex matchers")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Link: https://patch.msgid.link/aEmBONjyiF6z5yCV@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The veth peer device is RCU protected, but when the peer device gets
deleted (veth_dellink) then the pointer is assigned NULL (via
RCU_INIT_POINTER).
This patch adds a necessary NULL check in veth_xdp_rcv when accessing
the veth peer net_device.
This fixes a bug introduced in commit dc82a33297fc ("veth: apply qdisc
backpressure on full ptr_ring to reduce TX drops"). The bug is a race
and only triggers when having inflight packets on a veth that is being
deleted.
Reported-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Closes: https://lore.kernel.org/all/fecfcad0-7a16-42b8-bff2-66ee83a6e5c4@linux.dev/
Reported-by: syzbot+c4c7bf27f6b0c4bd97fe@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/683da55e.a00a0220.d8eae.0052.GAE@google.com/
Fixes: dc82a33297fc ("veth: apply qdisc backpressure on full ptr_ring to reduce TX drops")
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Acked-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Link: https://patch.msgid.link/174964557873.519608.10855046105237280978.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When performing a non-exact phy_caps lookup, we are looking for a
supported mode that matches as closely as possible the passed speed/duplex.
Blamed patch broke that logic by returning a match too early in case
the caller asks for half-duplex, as a full-duplex linkmode may match
first, and returned as a non-exact match without even trying to mach on
half-duplex modes.
Reported-by: Jijie Shao <shaojijie@huawei.com>
Closes: https://lore.kernel.org/netdev/20250603102500.4ec743cf@fedora/T/#m22ed60ca635c67dc7d9cbb47e8995b2beb5c1576
Tested-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Fixes: fc81e257d19f ("net: phy: phy_caps: Allow looking-up link caps based on speed and duplex")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250606094321.483602-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In
riocm_cdev_ioctl(RIO_CM_CHAN_SEND)
-> cm_chan_msg_send()
-> riocm_ch_send()
cm_chan_msg_send() checks that userspace didn't send too much data but
riocm_ch_send() failed to check that userspace sent sufficient data. The
result is that riocm_ch_send() can write to fields in the rio_ch_chan_hdr
which were outside the bounds of the space which cm_chan_msg_send()
allocated.
Address this by teaching riocm_ch_send() to check that the entire
rio_ch_chan_hdr was copied in from userspace.
Reported-by: maher azz <maherazz04@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Alexandre Bounine <alex.bou9@gmail.com>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Use the newly defined `CpuId` abstraction instead of raw CPU numbers.
This also fixes a doctest failure for configurations where `nr_cpu_ids <
4`.
The C `cpumask_{set|clear}_cpu()` APIs emit a warning when given an
invalid CPU number — but only if `CONFIG_DEBUG_PER_CPU_MAPS=y` is set.
Meanwhile, `cpumask_weight()` only considers CPUs up to `nr_cpu_ids`,
which can cause inconsistencies: a CPU number greater than `nr_cpu_ids`
may be set in the mask, yet the weight calculation won't reflect it.
This leads to doctest failures when `nr_cpu_ids < 4`, as the test tries
to set CPUs 2 and 3:
rust_doctest_kernel_cpumask_rs_0.location: rust/kernel/cpumask.rs:180
rust_doctest_kernel_cpumask_rs_0: ASSERTION FAILED at rust/kernel/cpumask.rs:190
Fixes: 8961b8cb3099 ("rust: cpumask: Add initial abstractions")
Reported-by: Miguel Ojeda <ojeda@kernel.org>
Closes: https://lore.kernel.org/rust-for-linux/CANiq72k3ozKkLMinTLQwvkyg9K=BeRxs1oYZSKhJHY-veEyZdg@mail.gmail.com/
Reported-by: Andreas Hindborg <a.hindborg@kernel.org>
Closes: https://lore.kernel.org/all/87qzzy3ric.fsf@kernel.org/
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
|
|
When the link is up, either eth_proto_oper or ext_eth_proto_oper
typically reports the active link protocol, from which both speed
and number of lanes can be retrieved. However, in certain cases,
such as when a NIC is connected via a non-standard cable, the
firmware may not report the protocol.
In such scenarios, the speed can still be obtained from the
data_rate_oper field in PTYS register. Since data_rate_oper
provides only speed information and lacks lane details, it is
incorrect to derive the number of lanes from it.
This patch corrects the behavior by setting the number of lanes to
UNKNOWN instead of incorrectly using MAX_LANES when relying on
data_rate_oper.
Fixes: 7e959797f021 ("net/mlx5e: Enable lanes configuration when auto-negotiation is off")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-10-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, a unique tunnel id was added for the matching on TC
non-zero chains, to support inner header rewrite with goto action.
Later, it was used to support VF tunnel offload for vxlan, then for
Geneve and GRE. To support VF tunnel, a temporary mlx5_flow_spec is
used to parse tunnel options. For Geneve, if there is TLV option, a
object is created, or refcnt is added if already exists. But the
temporary mlx5_flow_spec is directly freed after parsing, which causes
the leak because no information regarding the object is saved in
flow's mlx5_flow_spec, which is used to free the object when deleting
the flow.
To fix the leak, call mlx5_geneve_tlv_option_del() before free the
temporary spec if it has TLV object.
Fixes: 521933cdc4aa ("net/mlx5e: Support Geneve and GRE with VF tunnel offload")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When there are more than one destinations, we create a FW flow
table and provide it with all the destinations. FW requires to
have wire as the last destination in the list (if it exists),
otherwise the operation fails with FW syndrome.
This patch fixes the destination array action creation: if it
contains a wire destination, it is moved to the end.
Fixes: 504e536d9010 ("net/mlx5: HWS, added actions handling")
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-7-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix missing field handling in definer - outer IP version.
Fixes: 74a778b4a63f ("net/mlx5: HWS, added definers handling")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The newly introduced mutex is only used for reformat actions, but it was
initialized for modify header instead.
The struct that contains the mutex is zero-initialized and an all-zero
mutex is valid, so the issue only shows up with CONFIG_DEBUG_MUTEXES.
Fixes: b206d9ec19df ("net/mlx5: HWS, register reformat actions with fw")
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When attempting to add a rule to an existing flow group, if a matching
flow group exists but is not active, the error code returned should be
EAGAIN, so that the rule can be added to the matching flow group once
it is active, rather than ENOENT, which indicates that no matching
flow group was found.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Gavi Teitz <gavi@nvidia.com>
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix shutdown flow UAF when a virtual function is created on the embedded
chip (ECVF) of a BlueField device. In such case the vport acl ingress
table is not properly destroyed.
ECVF functionality is independent of ecpf_vport_exists capability and
thus functions mlx5_eswitch_(enable|disable)_pf_vf_vports() should not
test it when enabling/disabling ECVF vports.
kernel log:
[] refcount_t: underflow; use-after-free.
[] WARNING: CPU: 3 PID: 1 at lib/refcount.c:28
refcount_warn_saturate+0x124/0x220
----------------
[] Call trace:
[] refcount_warn_saturate+0x124/0x220
[] tree_put_node+0x164/0x1e0 [mlx5_core]
[] mlx5_destroy_flow_table+0x98/0x2c0 [mlx5_core]
[] esw_acl_ingress_table_destroy+0x28/0x40 [mlx5_core]
[] esw_acl_ingress_lgcy_cleanup+0x80/0xf4 [mlx5_core]
[] esw_legacy_vport_acl_cleanup+0x44/0x60 [mlx5_core]
[] esw_vport_cleanup+0x64/0x90 [mlx5_core]
[] mlx5_esw_vport_disable+0xc0/0x1d0 [mlx5_core]
[] mlx5_eswitch_unload_ec_vf_vports+0xcc/0x150 [mlx5_core]
[] mlx5_eswitch_disable_sriov+0x198/0x2a0 [mlx5_core]
[] mlx5_device_disable_sriov+0xb8/0x1e0 [mlx5_core]
[] mlx5_sriov_detach+0x40/0x50 [mlx5_core]
[] mlx5_unload+0x40/0xc4 [mlx5_core]
[] mlx5_unload_one_devl_locked+0x6c/0xe4 [mlx5_core]
[] mlx5_unload_one+0x3c/0x60 [mlx5_core]
[] shutdown+0x7c/0xa4 [mlx5_core]
[] pci_device_shutdown+0x3c/0xa0
[] device_shutdown+0x170/0x340
[] __do_sys_reboot+0x1f4/0x2a0
[] __arm64_sys_reboot+0x2c/0x40
[] invoke_syscall+0x78/0x100
[] el0_svc_common.constprop.0+0x54/0x184
[] do_el0_svc+0x30/0xac
[] el0_svc+0x48/0x160
[] el0t_64_sync_handler+0xa4/0x12c
[] el0t_64_sync+0x1a4/0x1a8
[] --[ end trace 9c4601d68c70030e ]---
Fixes: a7719b29a821 ("net/mlx5: Add management of EC VF vports")
Reviewed-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When firmware asks the driver to allocate more pages, using event of
give_pages, the driver should always allocate it from same NUMA, the
original device NUMA. Current code uses dev_to_node() which can result
in different NUMA as it is changed by other driver flows, such as
mlx5_dma_zalloc_coherent_node(). Instead, use saved numa node for
allocating firmware pages.
Fixes: 311c7c71c9bb ("net/mlx5e: Allocate DMA coherent memory on reader NUMA node")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-06-10 (i40e, iavf, ice, e1000)
For i40e:
Robert Malz improves reset handling for situations where multiple reset
requests could cause some to be missed.
For iavf:
Ahmed adds detection, and handling, of reset that could occur early in
the initialization process to stop long wait/hangs.
For ice:
Anton, properly, sets missed use_nsecs value.
For e1000:
Joe Damato moves cancel_work_sync() call to avoid deadlock.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000: Move cancel_work_sync to avoid deadlock
ice/ptp: fix crosstimestamp reporting
iavf: fix reset_task for early reset event
i40e: retry VFLR handling if there is ongoing VF reset
i40e: return false from i40e_reset_vf if reset is in progress
====================
Link: https://patch.msgid.link/20250610171348.1476574-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If reset_control_acquire() fails, then we can't return directly.
We need to do a little clean up first.
Fixes: cf2c3eceb757 ("spi: stm32-ospi: Make usage of reset_control_acquire/release() API")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aEmAGTUzzKZlLe3K@stanley.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It isn't necessary to freeze queue for updating disk size given submit_bio()
doesn't grab queue usage counter for checking eod.
Also many driver won't freeze queue for calling set_capacity_and_notify().
Move lo_set_size() out of queue freeze for fixing many lockdep warning
report.
Link: https://lore.kernel.org/linux-block/67ea99e0.050a0220.3c3d88.0042.GAE@google.com/
Reported-by: syzbot+9dd7dbb1a4b915dee638@syzkaller.appspotmail.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250611084938.108829-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via C45 (clause 45) mdiobus,
there is no verification of parameters passed to the ioctl and
it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before C45 read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes: 4e4aafcddbbf ("net: mdio: Add dedicated C45 API to MDIO bus drivers")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via mdiobus, there is no verification of
parameters passed to the ioctl and it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes: 080bb352fad00 ("net: phy: Maintain MDIO device and bus statistics")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use common wrappers operating directly on the struct sg_table objects to
fix incorrect use of scatterlists sync calls. dma_sync_sg_for_*()
functions have to be called with the number of elements originally passed
to dma_map_sg_*() function, not the one returned in sgtable's nents.
Fixes: 1ffe09590121 ("udmabuf: fix dma-buf cpu access")
CC: stable@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20250507160913.2084079-3-m.szyprowski@samsung.com
|
