| Age | Commit message (Collapse) | Author |
|---|
|
Upon NIXLF_ALLOC install a unicast forwarding rule in NPC MCAM
like below
- Match pkt DMAC with NIXLF attached PF/VF's MAC address.
- Ingress channel
- Action is UCAST
- Forward to PF_FUNC of this NIXLF
And broadcast pkt forwarding rule as
- Match L2B bit in MCAM search key
- Ingress channel
- Action is UCAST, for now, later it will be changed to MCAST.
Only PFs can install this rule
Upon NIXLF_FREE disable all MCAM entries in use by that NIXLF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add LMAC channel info like Rx/Tx channel base and count to
NIXLF_ALLOC mailbox message response. This info is used by
NIXLF attached RVU PF/VF to configure SQ's default channel,
TL3_TL2_LINKX_CFG and to install MCAM rules in NPC based
on matching ingress channel number.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds some minimal configuration for NPC MCAM and
LDATA extraction which is sufficient enough to install
ucast/bcast/promiscuous forwarding rules. Below is the
config done
- LDATA extraction config to extract DMAC from pkt
to offset 64bit in MCAM search key.
- Set MCAM lookup keysize to 224bits
- Set MCAM TX miss action to UCAST_DEFAULT
- Set MCAM RX miss action to DROP
Also inorder to have guaranteed space in MCAM to install
ucast forwarding rule for each of RVU PF/VF, reserved
one MCAM entry for each of NIXLF for ucast rule. And two
entries for each of RVU PF. One for bcast pkt replication
and other for promiscuous mode which allows all pkts
received on a HW CGX/LBK channel.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Config NPC layer info from KPU profile into protocol
checker to identify outer L2/IPv4/TCP/UDP headers in a
packet. And enable IPv4 checksum validation.
L3/L4 and L4 CSUM validation will be enabled by PF/VF
drivers by configuring NIX_AF_LF(0..127)_RX_CFG via mbox
i.e 'nix_lf_alloc_req->rx_cfg'
Also enable setting of NPC_RESULT_S[L2B] when an outer
L2 broadcast address is detected. This will help in
installing NPC MCAM rules for broadcast packets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support for PF/VF drivers to configure NIX to
capture and/or strip VLAN tag from ingress packets.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon NIXLF ALLOC/FREE, add or remove corresponding PF_FUNC from
the broadcast packet replication list of the CGX LMAC mapped
RVU PF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate memory for mcast/bcast/mirror replication entry
contexts, replication buffers (used by HW) and config HW
with corresponding memory bases. Added support for installing
MCEs via NIX AQ mbox.
For now support is restricted to broadcast pkt replication,
hence MCE table size and number of replication buffers
allocated are less. Each CGX LMAC mapped RVU PF is assigned
a MCE table of size 'num VFs of that PF + PF'.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For each CGX LMAC that is mapped to a RVU PF, allocate
a pkind and config the same in CGX. For a received packet
at CGX LMAC interface this pkind is used by NPC block
to start parsing of packet.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch configures all 16 KPUs and iKPU (pkinds) with
the KPU parser profile defined in npc_profile.h. Each KPU
engine has a 128 entry CAM, only CAM entries which are listed
in the profile are enabled and rest are left disabled.
Also
- Memory is allocated for pkind's bitmap and PFFUNC, interface
channel mapping.
- Added all CSR offsets of NPC HW block.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NPC block is responsible for parsing and forwarding
packets to different NIXLFs. NPC has 16 KPU engines
(Kangaroo parse engine) and one iKPU which represents
pkinds. Each physical port either CGX/LBK is assigned
a pkind and upon receiving a packet HW takes that port's
pkind and starts parsing as per the KPU engines config.
This patch adds header files which contain configuration
profile/array for each of the iKPU and 16 KPU engines.
Signed-off-by: Hao Zheng <hao.zheng@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new mailbox message to reset
a NIXLF's receive and transmit HW stats.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for a PF/VF driver to configure
NIX transmit scheduler queues via mbox. Since PF/VF doesn't
know the absolute HW index of the NIXLF attached to it, AF
traps the register config and overwrites with the correct
NIXLF index.
HW supports shaping, colouring and policing of packets with
these multilevel traffic scheduler queues. Instead of
introducing different mbox message formats for different
configurations and making both AF & PF/VF driver implementation
cumbersome, access to the scheduler queue's CSRs is provided
via mbox. AF checks whether the sender PF/VF has the
corresponding queue allocated or not and dumps the config
to HW. With a single mbox msg 20 registers can be configured.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support for a PF/VF to allocate or free NIX transmit
scheduler queues via mbox. For setting up pkt transmission
priorities between queues, the scheduler queues have to be
contiguous w.r.t their HW indices. So both contiguous and
non-contiguous allocations are supported.
Upon receiving NIX_TXSCH_FREE mbox msg all scheduler queues
allocated to sending PFFUNC (PF/VF) will be freed. Selective
free is not supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract error information from rx and tx buffer descriptors,
and update error counters.
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
linux/prefetch.h is never explicitly included in ena_com, although
functions from it, such as prefetchw(), are used throughout ena_com.
This is an inclusion bug, and we fix it here by explicitly including
linux/prefetch.h. The bug was exposed when the driver was compiled
for the xtensa architecture.
Fixes: 689b2bdaaa14 ("net: ena: add functions for handling Low Latency Queues in ena_com")
Fixes: 8c590f977638 ("ena: Fix Kconfig dependency on X86")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FDB_MAX_CHAIN is three. We wanted to allocate enough memory to hold four
structs but there are missing parentheses so we only allocate enough
memory for three structs and the first byte of the fourth one.
Fixes: 328edb499f99 ("net/mlx5: Split FDB fast path prio to multiple namespaces")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When indicating the MAC supports Symmetric Pause, clear the Asymmetric
Pause bit, which could of been already set is the PHY supports it.
Reported-by: Labbe Corentin <clabbe@baylibre.com>
Fixes: c306ad36184f ("net: ethernet: Add helper for MACs which support pause")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These functions are supposed to return one on failure and zero on
success. Returning a zero here could cause uninitialized variable
bugs in several of the callers. For example:
drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:1660 get_iscsi_dcb_priority()
error: uninitialized symbol 'caps'.
Fixes: 48365e485275 ("qlcnic: dcb: Add support for CEE Netlink interface.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables and process hw errors of TM scheduler and
QCN(Quantized Congestion Control).
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables and process hw errors from the
PPP(Programmable Packet Process) block.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds enable and processing of hw errors from IGU(Ingress Unit),
EGU(Egress Unit) and NCSI(Network Controller Sideband Interface).
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds enable and processing of ecc errors from
common HNS blocks, CMDQ(Command Queue),
IMP(Integrated Management Processor) and TQP(Task Queue Pair).
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds functions to enable and disable hw errors.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the error recovery for the HNS hw errors.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set of hw errors occurred in the HNS3 are reported to the
hns3 driver through PCIe AER and RAS.The error info will be
processed and appropriately recovered.
This patch adds error_detected callback and error processing.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns (trimmed for brevity):
drivers/isdn/mISDN/tei.c:1193:7: warning: overflow converting case value
to switch condition type (2147764552 to 18446744071562348872) [-Wswitch]
case IMHOLD_L1:
^
drivers/isdn/mISDN/tei.c:1187:7: warning: overflow converting case value
to switch condition type (2147764550 to 18446744071562348870) [-Wswitch]
case IMCLEAR_L2:
^
2 warnings generated.
The root cause is that the _IOC macro can generate really large numbers,
which don't find into type int. My research into how GCC and Clang are
handling this at a low level didn't prove fruitful and surveying the
kernel tree shows that aside from here and a few places in the scsi
subsystem, everything that uses _IOC is at least of type 'unsigned int'.
Make that change here because as nothing in this function cares about
the signedness of the variable and it removes ambiguity, which is never
good when dealing with compilers.
While we're here, remove the unnecessary local variable ret (just return
-EINVAL and 0 directly).
Link: https://github.com/ClangBuiltLinux/linux/issues/67
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/rvu.c: In function 'rvu_detach_rsrcs':
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:855:6: warning:
variable 'devnum' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:853:7: warning:
variable 'is_pf' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c: In function 'rvu_mbox_handler_ATTACH_RESOURCES':
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1054:7: warning:
variable 'is_pf' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1053:6: warning:
variable 'devnum' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
746ea74241fa ("octeontx2-af: Add RVU block LF provisioning support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c: In function 'rvu_npa_init':
drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c:446:20: warning:
variable 'block' set but not used [-Wunused-but-set-variable]
It never used since introduction in
commit 7a37245ef23f ("octeontx2-af: NPA block admin queue init")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, there is an out-of-bounds read on array ctrl->phys,
once variable i reaches the maximum array size of SERDES_MAX
in the for loop.
Fix this by changing the condition in the for loop from
i <= SERDES_MAX to i < SERDES_MAX.
Addresses-Coverity-ID: 1473966 ("Out-of-bounds read")
Addresses-Coverity-ID: 1473959 ("Out-of-bounds read")
Fixes: 51f6b410fc22 ("phy: add driver for Microsemi Ocelot SerDes muxing")
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns:
drivers/isdn/hisax/hfc_pci.c:131:34: error: if statement has empty body
[-Werror,-Wempty-body]
if (Read_hfc(cs, HFCPCI_INT_S1));
^
drivers/isdn/hisax/hfc_pci.c:131:34: note: put the semicolon on a
separate line to silence this warning
In my attempt to hide the warnings because I thought they didn't serve
any purpose[1], Masahiro Yamada pointed out that {Read,Write}_hfc in
hci_pci.c should be using a standard register access method; otherwise,
the compiler will just remove the if statements.
For hfc_pci, use the versions of {Read,Write}_hfc found in
drivers/isdn/hardware/mISDN/hfc_pCI.h while converting pci_io to be
'void __iomem *' (and clean up ioremap) then remove the empty if
statements.
For hfc_sx, {Read,Write}_hfc are already use a proper register accessor
(inb, outb) so just remove the unnecessary if statements.
[1]: https://lore.kernel.org/lkml/20181016021454.11953-1-natechancellor@gmail.com/
Link: https://github.com/ClangBuiltLinux/linux/issues/66
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the
GPIO descriptor API, there's a small addition to the GPIO API plus a
bunch of updates to board files to implement it. This is some really
welcome work from Linus Walleij that's had a bunch of review and has
been sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices"
* tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: lochnagar: Use a consisent comment style for SPDX header
regulator: bd718x7: Remove struct bd718xx_pmic
regulator: Fetch enable gpiods nonexclusive
regulator/gpio: Allow nonexclusive GPIO access
regulator: lochnagar: Add support for the Cirrus Logic Lochnagar
regulator: stpmic1: Return REGULATOR_MODE_INVALID for invalid mode
regulator: stpmic1: add stpmic1 regulator driver
dt-bindings: regulator: document stpmic1 pmic regulators
regulator: axp20x: Mark expected switch fall-throughs
regulator: bd718xx: fix build warning on x86_64
regulator: fixed: Default enable high on DT regulators
regulator: bd718xx: rename bd71837 to 718xx
regulator: bd718XX use pickable ranges
regulator/mfd: bd718xx: rename bd71837/bd71847 common instances
regulator: Support regulators where voltage ranges are selectable
mfd: dt bindings: add BD71847 device-tree binding documentation
regulator: dt bindings: add BD71847 device-tree binding documentation
regulator/mfd: Support ROHM BD71847 power management IC
regulator: da905{2,5}: Remove unnecessary array check
regulator: qcom: Add PMS405 regulators
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"One new core feature here, a small collection of new drivers and a
bunch of small improvements in existing drivers:
- A new CS_WORD flag for transfers where the chip select is toggled
at every word, with both a generic implementation and the ability
for controllers to do this automatically (including a DaVinci one).
- New drivers for Mediatek MT2712, Qualcomm GENI and QSPI, Spreadtrum
SPI and ST STM32 QSPI plus new IDs for several existing ones"
* tag 'spi-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (86 commits)
spi: lpspi: add imx8qxp compatible string
spi: Allow building SPI_BCM63XX_HSSPI on ARM-based SoCs
spi: omap2-mcspi: Add slave mode support
spi: omap2-mcspi: Set FIFO DMA trigger level to word length
spi: omap2-mcspi: Switch to readl_poll_timeout()
spi: spi-mem: add stm32 qspi controller
dt-bindings: spi: add stm32 qspi controller
spi: sh-msiof: document R8A779{7|8}0 bindings
spi: pic32-sqi: don't pass GFP_DMA32 to dma_alloc_coherent
MAINTAINERS: Add entry for Broadcom SPI controller
spi: sh-msiof: fix deferred probing
spi: imx: use PIO mode if size is small
spi: imx: correct wml as the last sg length
spi: imx: move wml setting to later than setup_transfer
PCI: Provide pci_match_id() with CONFIG_PCI=n
spi: Make GPIO CSs honour the SPI_NO_CS flag
spi/spi-pxa2xx: add PXA2xx SSP SPI Controller
spi: pxa2xx: Add devicetree support
spi: pxa2xx: Use an enum for type
spi: spi-geni-qcom: Add SPI driver support for GENI based QUP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A small update with a couple of new APIs that are useful for some
small sets of devices:
- Split up the single_rw flagging to map read and write separately as
some devices support bulk operations for only read or only write.
- Add a write version of the noinc API.
- Clean up the code for LOG_DEVICE a bit"
* tag 'regmap-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use less #ifdef for LOG_DEVICE
regmap: Add regmap_noinc_write API
regmap: split up regmap_config.use_single_rw
regmap: fix comment for regmap.use_single_write
|
|
Pull mtd updates from Boris Brezillon:
"SPI NOR core changes:
- Support non-uniform erase size
- Support controllers with limited TX fifo size
Driver changes:
- m25p80: Re-issue a WREN command after each write access
- cadence: Pass a proper dir value to dma_[un]map_single()
- fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
- intel-spi: Add a new PCI entry for Ice Lake
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID
byte.
MTD changes:
- physmap cleanups/fixe
- gpio-addr-flash cleanups/fixes"
* tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits)
jffs2: free jffs2_sb_info through jffs2_kill_sb()
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
mtd: maps: gpio-addr-flash: Convert to gpiod
mtd: maps: gpio-addr-flash: Replace array with an integer
mtd: maps: gpio-addr-flash: Use order instead of size
mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
mtd: spi-nor: Support controllers with limited TX FIFO size
mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single
mtd: spi-nor: parse SFDP Sector Map Parameter Table
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: rawnand: marvell: fix the IRQ handler complete() condition
mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered"
mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
mtd: maps: gpio-addr-flash: Use devm_* functions
mtd: maps: gpio-addr-flash: Fix ioremapped size
mtd: maps: gpio-addr-flash: Replace custom printk
mtd: physmap_of: Release resources on error
...
|
|
Setup the cpu_logical_map during boot. Moreover, every SBI call
and PLIC context are based on the physical hartid. Use the logical
CPU to hartid mapping to pass correct hartid to respective functions.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
It's a bit confusing exactly what this function does: it actually
returns the hartid of an OF processor node, failing with -1 on invalid
nodes. I've changed the name to _hartid() in order to make that a bit
more clear, as well as adding a comment.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add support for trace events to hwmon core
- Add support for NCT6797D, NCT6798D, MAX31725/6, LTM4686
- Support all AMD Family 15h Model 6xh and Model 7xh processors in
k10temp driver
- Convert ina3221 driver to _info API
- Fixes, cleanups, and improvements in various drivers
* tag 'hwmon-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (46 commits)
hwmon: (pmbus) Fix page count auto-detection.
hwmon: (pmbus) remove redundant 'default n' from Kconfig
hwmon: (core) Add trace events to _attr_show/store functions
hwmon: (ina3221) Use _info API to register hwmon device
hwmon: (npcm-750-pwm-fan) Change initial pwm target to 255
hwmon: (ina3221) Validate shunt resistor value from DT
hwmon: (tmp421) make const array 'names' static
hwmon: (core) Add hwmon_in_enable attribute
hwmon: (ina3221) mark PM functions as __maybe_unused
hwmon: (ina3221) Read channel input source info from DT
dt-bindings: hwmon: Add ina3221 documentation
hwmon: (ina3221) Add suspend and resume functions
hwmon: (ina3221) Fix INA3221_CONFIG_MODE macros
hwmon: (ina3221) Add INA3221_CONFIG to volatile_table
MAINTAINERS: Update PMBUS maintainer entry
hwmon: (pwm-fan) Set fan speed to 0 on suspend
hwmon: (pwm-fan) Silence error on probe deferral
hwmon: (scpi-hwmon) remove redundant continue
hwmon: (nct6775) Add support for NCT6798D
hwmon: (nct6775) Add support for NCT6797D
...
|
|
Pull dma mapping updates from Christoph Hellwig:
"First batch of dma-mapping changes for 4.20.
There will be a second PR as some big changes were only applied just
before the end of the merge window, and I want to give them a few more
days in linux-next.
Summary:
- mostly more consolidation of the direct mapping code, including
converting over hexagon, and merging the coherent and non-coherent
code into a single dma_map_ops instance (me)
- cleanups for the dma_configure/dma_unconfigure callchains (me)
- better handling of dma_masks in odd setups (me, Alexander Duyck)
- better debugging of passing vmalloc address to the DMA API (Stephen
Boyd)
- CMA command line parsing fix (He Zhe)"
* tag 'dma-mapping-4.20' of git://git.infradead.org/users/hch/dma-mapping: (27 commits)
dma-direct: respect DMA_ATTR_NO_WARN
dma-mapping: translate __GFP_NOFAIL to DMA_ATTR_NO_WARN
dma-direct: document the zone selection logic
dma-debug: Check for drivers mapping invalid addresses in dma_map_single()
dma-direct: fix return value of dma_direct_supported
dma-mapping: move dma_default_get_required_mask under ifdef
dma-direct: always allow dma mask <= physiscal memory size
dma-direct: implement complete bus_dma_mask handling
dma-direct: refine dma_direct_alloc zone selection
dma-direct: add an explicit dma_direct_get_required_mask
dma-mapping: make the get_required_mask method available unconditionally
unicore32: remove swiotlb support
Revert "dma-mapping: clear dev->dma_ops in arch_teardown_dma_ops"
dma-mapping: support non-coherent devices in dma_common_get_sgtable
dma-mapping: consolidate the dma mmap implementations
dma-mapping: merge direct and noncoherent ops
dma-mapping: move the dma_coherent flag to struct device
MIPS: don't select DMA_MAYBE_COHERENT from DMA_PERDEV_COHERENT
dma-mapping: add the missing ARCH_HAS_SYNC_DMA_FOR_CPU_ALL declaration
dma-mapping: fix panic caused by passing empty cma command line argument
...
|
|
Pull libata updates from Jens Axboe:
"Here are the libata changes queued up for 4.20:
- %pOFn device_node.name conversion (Rob Herring)
- Use LBAM/LBAH password defines instead of hardcoding (Linus
Walleij)
- Series adding support for the allwinner R40 AHCI controller
(Corentin Labbe)
- Disable ALPM for Ampere Computing device (Suman Tripathi)
- ahci bcrm fixes (Florian Fainelli)
- Redundant Kconfig defaults (Bartlomiej Zolnierkiewicz)
- Code cleanups (Nathan Chancellor)"
* tag 'for-4.20/libata-20181021' of git://git.kernel.dk/linux-block:
ata: remove redundant 'default n' from Kconfig
ata: ep93xx: Use proper enums for directions
ata: ahci_brcm: Allow using driver or DSL SoCs
ata: ahci_brcm: Match BCM63138 compatible strings
ata: ahci_brcm: Allow optional reset controller to be used
dt-bindings: ata: Document BCM63138 compatible string
pata_atiixp: Remove unnecessary parentheses
ata: Disable AHCI ALPM feature for Ampere Computing eMAG SATA
dt-bindings: ata: update ahci_sunxi bindings
ata: ahci_sunxi: add support for r40
dt-bindings: ata: ahci-platform: document phy-supply
ata: ahci_platform: add support for PHY controller regulator
dt-bindings: ata: ahci-platform: document ahci-supply
ata: ahci_platform: add support for AHCI controller regulator
dt-bindings: ata: ahci-platform: fix indentation of target-supply
libata: Use SMART LBAM/LBAH password defines
ata: ahci: Convert to using %pOFn instead of device_node.name
|
|
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Apart from some new arm64 features and clean-ups, this also contains
the core mmu_gather changes for tracking the levels of the page table
being cleared and a minor update to the generic
compat_sys_sigaltstack() introducing COMPAT_SIGMINSKSZ.
Summary:
- Core mmu_gather changes which allow tracking the levels of
page-table being cleared together with the arm64 low-level flushing
routines
- Support for the new ARMv8.5 PSTATE.SSBS bit which can be used to
mitigate Spectre-v4 dynamically without trapping to EL3 firmware
- Introduce COMPAT_SIGMINSTKSZ for use in compat_sys_sigaltstack
- Optimise emulation of MRS instructions to ID_* registers on ARMv8.4
- Support for Common Not Private (CnP) translations allowing threads
of the same CPU to share the TLB entries
- Accelerated crc32 routines
- Move swapper_pg_dir to the rodata section
- Trap WFI instruction executed in user space
- ARM erratum 1188874 workaround (arch_timer)
- Miscellaneous fixes and clean-ups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (78 commits)
arm64: KVM: Guests can skip __install_bp_hardening_cb()s HYP work
arm64: cpufeature: Trap CTR_EL0 access only where it is necessary
arm64: cpufeature: Fix handling of CTR_EL0.IDC field
arm64: cpufeature: ctr: Fix cpu capability check for late CPUs
Documentation/arm64: HugeTLB page implementation
arm64: mm: Use __pa_symbol() for set_swapper_pgd()
arm64: Add silicon-errata.txt entry for ARM erratum 1188873
Revert "arm64: uaccess: implement unsafe accessors"
arm64: mm: Drop the unused cpu parameter
MAINTAINERS: fix bad sdei paths
arm64: mm: Use #ifdef for the __PAGETABLE_P?D_FOLDED defines
arm64: Fix typo in a comment in arch/arm64/mm/kasan_init.c
arm64: xen: Use existing helper to check interrupt status
arm64: Use daifflag_restore after bp_hardening
arm64: daifflags: Use irqflags functions for daifflags
arm64: arch_timer: avoid unused function warning
arm64: Trap WFI executed in userspace
arm64: docs: Document SSBS HWCAP
arm64: docs: Fix typos in ELF hwcaps
arm64/kprobes: remove an extra semicolon in arch_prepare_kprobe
...
|
|
The init of the pkey module currently fails if the pckmo instruction
or the subfunctions are not available. However, customers may
restrict their LPAR to switch off exactly these functions and work
with secure key only. So it is a valid case to have the pkey module
active and use it for secure key to protected key transfer only.
This patch moves the pckmo subfunction check from the pkey module init
function into the internal function where the pckmo instruction is
called. So now only on invocation of the pckmo instruction the check
for the required subfunction is done. If not available EOPNOTSUPP is
returned to the caller.
The check for having the pckmo instruction available is still done
during module init. This instruction came in with MSA 3 together with
the basic set of kmc instructions needed to work with protected keys.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Implement two new kind of BPF maps, that is, queue and stack
map along with new peek, push and pop operations, from Mauricio.
2) Add support for MSG_PEEK flag when redirecting into an ingress
psock sk_msg queue, and add a new helper bpf_msg_push_data() for
insert data into the message, from John.
3) Allow for BPF programs of type BPF_PROG_TYPE_CGROUP_SKB to use
direct packet access for __skb_buff, from Song.
4) Use more lightweight barriers for walking perf ring buffer for
libbpf and perf tool as well. Also, various fixes and improvements
from verifier side, from Daniel.
5) Add per-symbol visibility for DSO in libbpf and hide by default
global symbols such as netlink related functions, from Andrey.
6) Two improvements to nfp's BPF offload to check vNIC capabilities
in case prog is shared with multiple vNICs and to protect against
mis-initializing atomic counters, from Jakub.
7) Fix for bpftool to use 4 context mode for the nfp disassembler,
also from Jakub.
8) Fix a return value comparison in test_libbpf.sh and add several
bpftool improvements in bash completion, documentation of bpf fs
restrictions and batch mode summary print, from Quentin.
9) Fix a file resource leak in BPF selftest's load_kallsyms()
helper, from Peng.
10) Fix an unused variable warning in map_lookup_and_delete_elem(),
from Alexei.
11) Fix bpf_skb_adjust_room() signature in BPF UAPI helper doc,
from Nicolas.
12) Add missing executables to .gitignore in BPF selftests, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
