| Age | Commit message (Collapse) | Author |
|---|
|
tpm_ibmvtpm_send() can fail during PowerVM Live Partition Mobility resume
with an H_CLOSED return from ibmvtpm_send_crq(). The PAPR says, 'The
"partner partition suspended" transport event disables the associated CRQ
such that any H_SEND_CRQ hcall() to the associated CRQ returns H_Closed
until the CRQ has been explicitly enabled using the H_ENABLE_CRQ hcall.'
This patch adds a check in tpm_ibmvtpm_send() for an H_CLOSED return from
ibmvtpm_send_crq() and in that case calls tpm_ibmvtpm_resume() and
retries the ibmvtpm_send_crq() once.
Cc: stable@vger.kernel.org # 3.7.x
Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Reported-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: George Wilson <gcwilson@linux.ibm.com>
Tested-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This patch fixes the following problem when the ibmvtpm driver
is built as a module:
ERROR: modpost: "tpm2_get_cc_attrs_tbl" [drivers/char/tpm/tpm_ibmvtpm.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:94: __modpost] Error 1
make: *** [Makefile:1298: modules] Error 2
Fixes: 18b3670d79ae ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
genl_lock(); by genl_rcv_msc()
rtnl_lock(); by team_nl_cmd_options_set()
mutex_lock(&team->lock); by team_nl_team_get()
Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.
The problem secenario.
CPU0 CPU1
team_mode_get
request_module()
modprobe -r team_mode_roundrobin
team <--(B)
modprobe team <--(A)
team_mode_roundrobin
By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.
By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.
Test commands:
while :
do
teamd -d &
killall teamd &
modprobe -rv team_mode_roundrobin &
done
The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.
Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add parentheses to avoid possible vaddr overflow.
Fixes: a54eb55045ae ("vfio iommu type1: Add support for mediated devices")
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
instead of calling __copy_to/from_user(), use copy_to_from_user() to
ensure vaddr range is a valid user address range before accessing them.
Fixes: 8d46c0cca5f4 ("vfio: introduce vfio_dma_rw to read/write a range of IOVAs")
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:
==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
dump_backtrace+0x0/0x2a0
show_stack+0x20/0x30
dump_stack+0xec/0x148
print_address_description.isra.12+0x70/0x35c
__kasan_report+0xfc/0x1d4
kasan_report+0x4c/0x68
__asan_load4+0x9c/0xd8
_get_maxdiv+0x74/0xd8
clk_divider_bestdiv+0x74/0x5e0
clk_divider_round_rate+0x80/0x1a8
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_hw_round_rate+0xac/0xf0
clk_factor_round_rate+0xb8/0xd0
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_core_round_rate_nolock+0xbc/0x108
clk_core_set_rate_nolock+0xc4/0x2e8
clk_set_rate+0x58/0xe0
meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
platform_drv_probe+0x78/0xd8
really_probe+0x158/0x610
driver_probe_device+0x140/0x1b0
device_driver_attach+0xa4/0xb0
__driver_attach+0xcc/0x1c8
bus_for_each_dev+0xf4/0x168
driver_attach+0x3c/0x50
bus_add_driver+0x238/0x2e8
driver_register+0xc8/0x1e8
__platform_driver_register+0x88/0x98
meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
do_one_initcall+0xa8/0x328
do_init_module+0xe8/0x368
load_module+0x3300/0x36b0
__do_sys_finit_module+0x120/0x1a8
__arm64_sys_finit_module+0x4c/0x60
el0_svc_common.constprop.2+0xe4/0x268
do_el0_svc+0x98/0xa8
el0_svc+0x24/0x68
el0_sync_handler+0x12c/0x318
el0_sync+0x158/0x180
The buggy address belongs to the variable:
div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]
Memory state around the buggy address:
ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
^
ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================
Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.
Let's add the empty structure that indicates the end of the array.
Fixes: bd6f48546b9c ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the function bcm_sysport_probe(), when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant message
here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Build fix for serial_core being module:
ERROR: modpost: "sysrq_toggle_support" [drivers/tty/serial/serial_core.ko] undefined!
ERROR: modpost: "sysrq_mask" [drivers/tty/serial/serial_core.ko] undefined!
Fixes: eaee41727e6d ("sysctl/sysrq: Remove __sysrq_enabled copy")
Cc: Jiri Slaby <jslaby@suse.com>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200420172317.599611-1-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Looks like I accidentally made it so you couldn't force DPCD backlight
support on, whoops. Fix that.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 17f5d57915be ("drm/i915: Force DPCD backlight mode on X1 Extreme 2nd Gen 4K AMOLED panel")
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200413214407.1851002-1-lyude@redhat.com
(cherry picked from commit d7fb38ae36a2dc97924b075ad1d1a88792777ea9)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Fix the warning caused by enabling the autosectionlabel extension in the
kernel Sphinx build:
Documentation/gpu/i915.rst:610: WARNING: duplicate label
gpu/i915:layout, other instance in Documentation/gpu/i915.rst
The autosectionlabel extension adds labels to each section title for
cross-referencing, but forbids identical section titles in a
document. With kernel-doc, this includes sections titles in the included
kernel-doc comments.
In the warning message, Sphinx is unable to reference the labels in
their true locations in the kernel-doc comments in source. In this case,
there's "Layout" sections in both gt/intel_workarounds.c and
i915_reg.h. Rename the section in the latter to "File Layout".
Fixes: 58ad30cf91f0 ("docs: fix reference to core-api/namespaces.rst")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417130109.12791-1-jani.nikula@intel.com
(cherry picked from commit 27be41de45a70fe1cb0ae1cbd2fd6da1ce3ffe9a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Right now dp.regs.dp_tp_ctl/status are only set during the encoder
pre_enable() hook, what is causing all reads and writes to those
registers to go to offset 0x0 before pre_enable() is executed.
So if i915 takes the BIOS state and don't do a modeset any following
link retraing will fail.
In the case that i915 needs to do a modeset, the DDI disable sequence
will write to a wrong register not disabling DP 'Transport Enable' in
DP_TP_CTL, making a HDMI modeset in the same port/transcoder to
not light up the monitor.
So here for GENs older than 12, that have those registers fixed at
port offset range it is loading at encoder/port init while for GEN12
it will keep setting it at encoder pre_enable() and during HW state
readout.
Fixes: 4444df6e205b ("drm/i915/tgl: move DP_TP_* to transcoder")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414230442.262092-1-jose.souza@intel.com
(cherry picked from commit edcb9028d66b44d74ba4f8b9daa379b004dc1f85)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
As on ICL, we want to use the Type-C aux handlers for the TBT aux wells
to ensure the DP_AUX_CH_CTL_TBT_IO flag is set properly.
Fixes: 656409bbaf87 ("drm/i915/tgl: Add power well support")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415233435.3064257-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 3cbdb97564a39020262e62b655e788b63cf426cb)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The check was always succeeding even in case of a mismatch due to the
HDCP_STATUS_ENC bit being set. Make sure both bits are actually set.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Fixes: 2320175feb74 ("drm/i915: Implement HDCP for HDMI")
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200328104100.12162-1-oliver.barta@aptiv.com
(cherry picked from commit 3ffaf56e912e76cf09c560244c8804f9bebda8b1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
If we use a non-forcewaked write to PMINTRMSK, it does not take effect
until much later, if at all, causing a loss of RPS interrupts and no GPU
reclocking, leaving the GPU running at the wrong frequency for long
periods of time.
Reported-by: Francisco Jerez <currojerez@riseup.net>
Suggested-by: Francisco Jerez <currojerez@riseup.net>
Fixes: 35cc7f32c298 ("drm/i915/gt: Use non-forcewake writes for RPS")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francisco Jerez <currojerez@riseup.net>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Cc: <stable@vger.kernel.org> # v5.6+
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170318.16771-2-chris@chris-wilson.co.uk
(cherry picked from commit a080bd994c4023042a2b605c65fa10a25933f636)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Media decompression support should not be advertised on any display
planes for steppings A0-C0.
Bspec: 53273
Fixes: 2dfbf9d2873a ("drm/i915/tgl: Gen-12 display can decompress surfaces compressed by the media engine")
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414211118.2787489-3-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit dbff5a8db9c630f61a892ab41a283445e01270f5)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Commit 261b3e1f2a01 ("mei: me: store irq number in the hw struct.")
stores the irq number in the hw struct before MSI is enabled. This
caused a regression for mei_me_synchronize_irq() waiting for the wrong
irq number. On my laptop this causes a hang on shutdown. Fix the issue
by storing the irq number after enabling MSI.
Fixes: 261b3e1f2a01 ("mei: me: store irq number in the hw struct.")
Signed-off-by: Benjamin Lee <ben@b1c1l1.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200417184538.349550-1-ben@b1c1l1.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vhost is currently broken on the some ARM configs.
The reason is that the ring element addresses are passed between
components with different alignments assumptions. Thus, if
guest selects a pointer and host then gets and dereferences
it, then alignment assumed by the host's compiler might be
greater than the actual alignment of the pointer.
compiler on the host from assuming pointer is aligned.
This actually triggers on ARM with -mabi=apcs-gnu - which is a
deprecated configuration. With this OABI, compiler assumes that
all structures are 4 byte aligned - which is stronger than
virtio guarantees for available and used rings, which are
merely 2 bytes. Thus a guest without -mabi=apcs-gnu running
on top of host with -mabi=apcs-gnu will be broken.
The correct fix is to force alignment of structures - however
that is an intrusive fix that's best deferred until the next release.
We didn't previously support such ancient systems at all - this surfaced
after vdpa support prompted removing dependency of vhost on
VIRTULIZATION. So for now, let's just add something along the lines of
depends on !ARM || AEABI
to the virtio Kconfig declaration, and add a comment that it has to do
with struct member alignment.
Note: we can't make VHOST and VHOST_RING themselves have
a dependency since these are selected. Add a new symbol for that.
We should be able to drop this dependency down the road.
Fixes: 20c384f1ea1a0bc7 ("vhost: refine vhost and vringh kconfig")
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Suggested-by: Richard Earnshaw <Richard.Earnshaw@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.7-rc2
DWC3 learns how to properly set maxpacket limit and got a fix for a
request completion bug. The raw gadget got a fix for
copy_to/from_user() checks. Atmel got an improvement on vbus
disconnect handling.
We're also adding support for another SoC to the Renesas DRD driver.
* tag 'fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: raw-gadget: Fix copy_to/from_user() checks
usb: raw-gadget: fix raw_event_queue_fetch locking
usb: gadget: udc: atmel: Fix vbus disconnect handling
usb: dwc3: gadget: Fix request completion check
usb: dwc3: gadget: Do link recovery for SS and SSP
dt-bindings: usb: renesas,usb3-peri: add r8a77961 support
dt-bindings: usb: renesas,usbhs: add r8a77961 support
dt-bindings: usb: usb-xhci: add r8a77961 support
docs: dt: qcom,dwc3.txt: fix cross-reference for a converted file
usb: dwc3: gadget: Properly set maxpacket limit
usb: dwc3: Fix GTXFIFOSIZ.TXFDEP macro name
usb: gadget: udc: bdc: Remove unnecessary NULL checks in bdc_req_complete
|
|
Commit 17e5888e4e18 ("x86: Select HARDIRQS_SW_RESEND on x86") fixes
the edge-triggered embedded-controller (WC) IRQ not being replayed after
resume when woken by opening the lid, which gets signaled by the EC.
This means that the lid_init_state=ACPI_BUTTON_LID_INIT_OPEN quirk for
the Asus T200TA is no longer necessary, the lid now works properly
without it, so drop the quirk.
Fixes: 17e5888e4e18 ("x86: Select HARDIRQS_SW_RESEND on x86")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The case ACPI_RESOURCE_TYPE_EXTENDED_IRQ inside acpi_pci_link_set()
is correctly using resource->res.data.extended_irq.foo for most settings,
but for the shareable setting it so far has accidentally been using
resource->res.data.irq.shareable instead of
resource->res.data.extended_irq.shareable.
Note that the old code happens to also work because the shareable field
offset is the same for both the acpi_resource_irq and
acpi_resource_extended_irq structs.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For some reason the Host Control2 register of the Xenon SDHCI controller
sometimes reports the bit representing 1.8V signaling as 0 when read
after it was written as 1. Subsequent read reports 1.
This causes the sdhci_start_signal_voltage_switch function to report
1.8V regulator output did not become stable
When CONFIG_PM is enabled, the host is suspended and resumend many
times, and in each resume the switch to 1.8V is called, and so the
kernel log reports this message annoyingly often.
Do an empty read of the Host Control2 register in Xenon's
.voltage_switch method to circumvent this.
This patch fixes this particular problem on Turris MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V...")
Cc: stable@vger.kernel.org # v4.16+
Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.
So set the below two host capabilities for qcom SDHC.
- MMC_CAP_WAIT_WHILE_BUSY
- MMC_CAP_NEED_RSP_BUSY
Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Open-coding a timeout loop invariably leads to errors with handling
the timeout properly in one corner case or another. In the case of
cqhci we might report "CQE stuck on" even if it wasn't stuck on.
You'd just need this sequence of events to happen in cqhci_off():
1. Call ktime_get().
2. Something happens to interrupt the CPU for > 100 us (context switch
or interrupt).
3. Check time and; set "timed_out" to true since > 100 us.
4. Read CQHCI_CTL.
5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break.
6. Since "timed_out" is true, falsely print the error message.
Rather than fixing the polling loop, use readx_poll_timeout() like
many people do. This has been time tested to handle the corner cases.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The recent commit 0d84c3e6a5b2 ("mmc: core: Convert to
mmc_poll_for_busy() for erase/trim/discard") makes use of the
->card_busy() op for SD cards. This uncovered that the ->card_busy() op
in the Meson SDIO driver was never working right:
while polling the busy status with ->card_busy()
meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC
register values 0x1f001f10 or 0x1f003f10. This translates to "three out
of four DAT lines are HIGH" and "all four DAT lines are HIGH", which
is interpreted as "the card is busy".
It turns out that no situation can be observed where all four DAT lines
are LOW, meaning the card is not busy anymore. Upon further research the
3.10 vendor driver for this controller does not implement the
->card_busy() op.
Remove the ->card_busy() op from the meson-mx-sdio driver since it is
not working. At the time of writing this patch it is not clear what's
needed to make the ->card_busy() implementation work with this specific
controller hardware. For all use-cases which have previously worked the
MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have
a ->card_busy() op anymore.
Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The Meson SDIO controller uses the DAT0 lane for hardware busy
detection. Set MMC_CAP_WAIT_WHILE_BUSY accordingly. This fixes
the following error observed with Linux 5.7 (pre-rc-1):
mmc1: Card stuck being busy! __mmc_poll_for_busy
blk_update_request: I/O error, dev mmcblk1, sector 17111080 op
0x3:(DISCARD) flags 0x0 phys_seg 1 prio class 0
Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix the following sparse warning:
drivers/mmc/core/mmc_ops.c:881:5: warning: symbol 'mmc_interrupt_hpi'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Fixes: 55c2b8b9a383 ("mmc: core: Re-work the code for eMMC sanitize")
Link: https://lore.kernel.org/r/20200403034727.11879-1-yanaijie@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
tidss uses devm_kzalloc to allocate DRM plane, encoder and crtc objects.
This is not correct as the lifetime of those objects should be longer
than the underlying device's.
When unloading tidss module, the devm_kzalloc'ed objects have already
been freed when tidss_release() is called, and the driver will accesses
freed memory possibly causing a crash, a kernel WARN, or other undefined
behavior, and also KASAN will give a bug.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415092006.26675-1-tomi.valkeinen@ti.com
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two build fixes for a couple clk drivers and a fix for the Unisoc
serial clk where we want to keep it on for earlycon"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sprd: don't gate uart console clock
clk: mmp2: fix link error without mmp2
clk: asm9260: fix __clk_hw_register_fixed_rate_with_accuracy typo
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes/updates for the interrupt subsystem:
- Remove setup_irq() and remove_irq(). All users have been converted
so remove them before new users surface.
- A set of bugfixes for various interrupt chip drivers
- Add a few missing static attributes to address sparse warnings"
* tag 'irq-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-bcm7038-l1: Make bcm7038_l1_of_init() static
irqchip/irq-mvebu-icu: Make legacy_bindings static
irqchip/meson-gpio: Fix HARDIRQ-safe -> HARDIRQ-unsafe lock order
irqchip/sifive-plic: Fix maximum priority threshold value
irqchip/ti-sci-inta: Fix processing of masked irqs
irqchip/mbigen: Free msi_desc on device teardown
irqchip/gic-v4.1: Update effective affinity of virtual SGIs
irqchip/gic-v4.1: Add support for VPENDBASER's Dirty+Valid signaling
genirq: Remove setup_irq() and remove_irq()
|
|
When the 'spi_device_id' table was removed, it omitted to cleanup/fix the
assignment:
'indio_dev->name = spi_get_device_id(spi)->name;'
After that patch 'spi_get_device_id(spi)' returns NULL, so this crashes
during probe with null de-ref.
This change fixes this by introducing an ad7192_chip_info struct, and
defines all part-names [that should be assigned to indio_dev->name] in a
'ad7192_chip_info_tbl' table.
With this change, the old 'st->devid' is also moved to be a
'chip_info->chip_id'. And the old 'ID_AD719X' macros have been renamed to
'CHIPID_AD719X'. Tld identifiers have been re-purposed to be enum/index
values in the new 'ad7192_chip_info_tbl'.
This should fix the bug, and maintain the ABI for the 'indio_dev->name'
field.
Fixes: 66614ab2be38 ("staging: iio: adc: ad7192: removed spi_device_id")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The first received byte is the MSB, followed by the LSB so the value needs
to be byte swapped.
Also, the ADC actually has a delay of one clock on the SPI bus. Read three
bytes to get the last bit.
Fixes: 8dd2d7c0fed7 ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Suspend/resume were not working correctly with pm runtime.
Now suspend check if the chip is already suspended, and
resume put runtime pm in the correct state.
Issues seen prior to this were:
When entering suspend, there was an error in logs because we
were disabling vddio regulator although it was already disabled.
And when resuming, the chip was pull back to full power but the
pm_runtime state was not updated. So it was believing it was
still suspended.
Fixes: 4599cac84614 ("iio: imu: inv_mpu6050: use runtime pm with autosuspend")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d245172675a ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
simultaneous mode
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Currently there is an off-by-one check on the number of channels that
will cause an arry overrun in array st->output_mode when calling the
function d5770r_store_output_range. Fix this by using >= rather than >
to check for maximum number of channels.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: cbbb819837f6 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
flush hw FIFO before device reset in order to avoid possible races
on interrupt line 1. If the first interrupt line is asserted during
hw reset the device will work in I3C-only mode (if it is supported)
Fixes: 801a6e0af0c6 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Fixes: 43901008fde0 ("iio: imu: st_lsm6dsx: add support to LSM6DSR")
Reported-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Vitor Soares <vitor.soares@synopsys.com>
Tested-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch fixes the call to iio_str_to_fixpoint when using 'dB' sufix.
Before this the scale_db was not used when parsing the string written to
the attribute and it failed with invalid value.
Fixes: b8528224741b ("iio: core: Handle 'dB' suffix in core")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add lock protection from race conditions to 104-quad-8 counter driver
generic interface code changes. Mutex calls used for protection.
Fixes: f1d8a071d45b ("counter: 104-quad-8: Add Generic Counter interface support")
Signed-off-by: Syed Nayyar Waris <syednwaris@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Commit 9ecc2d86171a ("net/mlx4_en: add xdp forwarding and data write support")
brought another indirect call in fast path.
Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call
when/if CONFIG_RETPOLINE=y
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In fine adjustement mode, which is the current default, the sub-second
increment register is the number of nanoseconds that will be added to
the clock when the accumulator overflows. At each clock cycle, the
value of the addend register is added to the accumulator.
Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the
frequency of the ptp clock actually is.
The adjustment is then done on the addend register, only incrementing
every X clock cycles X being the ratio between 50MHz and ptp_clock_rate
(addend = 2^32 * 50MHz/ptp_clock_rate).
This causes the following issues :
- In case the frequency of the ptp clock is inferior or equal to 50MHz,
the addend value calculation will overflow and the default
addend value will be set to 0, causing the clock to not work at
all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32).
- The resolution of the timestamping clock is limited to 20ns while it
is not needed, thus limiting the accuracy of the timestamping to
20ns.
Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate.
It will allow to reach the minimum possible frequency for
ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the
sub-second-increment to a higher value. For instance, for 25MHz, it
gives ssinc = 80ns and default_addend = 2^31.
It will also allow to use a lower value for sub-second-increment, thus
improving the timestamping accuracy with frequencies higher than
100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend =
2^31.
v1->v2:
- Remove modifications to the calculation of default addend, which broke
compatibility with clock frequencies for which 2000000000 / ptp_clk_freq
is not an integer.
- Modify description according to discussions.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 2 registers to write to enable a ptp ref clock coming from the
fpga.
One that enables the usage of the clock from the fpga for emac0 and emac1
as a ptp ref clock, and the other to allow signals from the fpga to reach
emac0 and emac1.
Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII,
PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will
be written and the ptp ref clock will be set as coming from the fpga.
Separate the 2 register writes to only enable signals from the fpga to
reach emac0 or emac1 when ptp ref clock is not coming from the fpga.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the
refcount of the "notif_urb".
When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which
forget to decrease the refcnt increased by usb_get_urb(), causing a
refcnt leak.
Fix this issue by calling usb_put_urb() before the
i2400mu_bus_bm_wait_for_ack() returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes: three in target, one on a sg error leg, two in qla2xxx
fixing warnings introduced in the last merge window and updating
MAINTAINERS and one in hisi_sas fixing a problem introduced by libata"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: add sg_remove_request in sg_common_write
scsi: target: tcmu: reset_ring should reset TCMU_DEV_BIT_BROKEN
scsi: target: fix PR IN / READ FULL STATUS for FC
scsi: target: Write NULL to *port_nexus_ptr if no ISID
scsi: MAINTAINERS: Update qla2xxx FC-SCSI driver maintainer
scsi: qla2xxx: Fix regression warnings
scsi: hisi_sas: Fix build error without SATA_HOST
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix up chip IDs (isl68137)
- error handling for invalid temperatures and use true module name
(drivetemp)
- Fix static symbol warnings (k10temp)
- Use valid hwmon device name (jc42)
* tag 'hwmon-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (jc42) Fix name to have no illegal characters
hwmon: (k10temp) make some symbols static
hwmon: (drivetemp) Return -ENODATA for invalid temperatures
hwmon: (drivetemp) Use drivetemp's true module name in Kconfig section
hwmon: (pmbus/isl68137) Fix up chip IDs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes and an old API removal now that all users are
gone"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: tegra: Synchronize DMA before termination
i2c: tegra: Better handle case where CPU0 is busy for a long time
i2c: remove i2c_new_probed_device API
i2c: altera: use proper variable to hold errno
i2c: designware: platdrv: Remove DPM_FLAG_SMART_SUSPEND flag on BYT and CHT
|
