| Age | Commit message (Collapse) | Author |
|---|
|
Although the vSGIs are not directly visible to the host, they still
get moved around by the CPU hotplug, for example. This results in
the kernel moaning on the console, such as:
genirq: irq_chip GICv4.1-sgi did not update eff. affinity mask of irq 38
Updating the effective affinity on set_affinity() fixes it.
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
When a vPE is made resident, the GIC starts parsing the virtual pending
table to deliver pending interrupts. This takes place asynchronously,
and can at times take a long while. Long enough that the vcpu enters
the guest and hits WFI before any interrupt has been signaled yet.
The vcpu then exits, blocks, and now gets a doorbell. Rince, repeat.
In order to avoid the above, a (optional on GICv4, mandatory on v4.1)
feature allows the GIC to feedback to the hypervisor whether it is
done parsing the VPT by clearing the GICR_VPENDBASER.Dirty bit.
The hypervisor can then wait until the GIC is ready before actually
running the vPE.
Plug the detection code as well as polling on vPE schedule. While
at it, tidy-up the kernel message that displays the GICv4 optional
features.
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Fixes: ee5cd41c9117 ("usb: dwc3: Update speed checks for SuperSpeedPlus")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:
For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).
For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.
Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.
Reference: Databook 3.30a section 3.2.2 and 3.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Change the macro name DWC3_GTXFIFOSIZ_TXFDEF to DWC3_GTXFIFOSIZ_TXFDEP
to match with the register name GTXFIFOSIZ.TXFDEP.
Fixes: 457e84b6624b ("usb: dwc3: gadget: dynamically re-size TxFifos")
Fixes: 0cab8d26d6e5 ("usb: dwc3: Update DWC_usb31 GTXFIFOSIZ reg fields")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
When building with Clang + -Wtautological-pointer-compare:
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:28: warning: comparison of
address of 'req->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~ ~~~~
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:51: warning: comparison of
address of 'req->usb_req' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~~~ ~~~~
2 warnings generated.
As it notes, these statements will always evaluate to false so remove
them.
Fixes: efed421a94e6 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Link: https://github.com/ClangBuiltLinux/linux/issues/749
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Remove shadow declaration of variable 'pullup' in mtk_pinconf_get()
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Link: https://lore.kernel.org/r/1586255632-27528-1-git-send-email-light.hsieh@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For skcipher algorithms, the input, output HW S/G tables
look like this: [IV, src][dst, IV]
Now, we can have 2 conditions here:
- there is no IV;
- src and dst are equal (in-place encryption) and scattered
and the error is an "off-by-one" in the HW S/G table.
This issue was seen with KASAN:
BUG: KASAN: slab-out-of-bounds in skcipher_edesc_alloc+0x95c/0x1018
Read of size 4 at addr ffff000022a02958 by task cryptomgr_test/321
CPU: 2 PID: 321 Comm: cryptomgr_test Not tainted
5.6.0-rc1-00165-ge4ef8383-dirty #4
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load4+0x90/0xb0
skcipher_edesc_alloc+0x95c/0x1018
skcipher_encrypt+0x84/0x150
crypto_skcipher_encrypt+0x50/0x68
test_skcipher_vec_cfg+0x4d4/0xc10
test_skcipher_vec+0x178/0x1d8
alg_test_skcipher+0xec/0x230
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Allocated by task 321:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
skcipher_edesc_alloc+0x21c/0x1018
skcipher_encrypt+0x84/0x150
crypto_skcipher_encrypt+0x50/0x68
test_skcipher_vec_cfg+0x4d4/0xc10
test_skcipher_vec+0x178/0x1d8
alg_test_skcipher+0xec/0x230
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff000022a02800
which belongs to the cache dma-kmalloc-512 of size 512
The buggy address is located 344 bytes inside of
512-byte region [ffff000022a02800, ffff000022a02a00)
The buggy address belongs to the page:
page:fffffe00006a8000 refcount:1 mapcount:0 mapping:ffff00093200c400
index:0x0 compound_mapcount: 0
flags: 0xffff00000010200(slab|head)
raw: 0ffff00000010200 dead000000000100 dead000000000122 ffff00093200c400
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff000022a02800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff000022a02880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff000022a02900: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
^
ffff000022a02980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff000022a02a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 334d37c9e263 ("crypto: caam - update IV using HW support")
Cc: <stable@vger.kernel.org> # v5.3+
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Here's the KASAN report:
BUG: KASAN: use-after-free in rsa_pub_done+0x70/0xe8
Read of size 1 at addr ffff000023082014 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc1-00162-gfcb90d5 #60
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load1+0x5c/0x68
rsa_pub_done+0x70/0xe8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
irq_exit+0x114/0x128
__handle_domain_irq+0x80/0xe0
gic_handle_irq+0x50/0xa0
el1_irq+0xb8/0x180
cpuidle_enter_state+0xa4/0x490
cpuidle_enter+0x48/0x70
call_cpuidle+0x44/0x70
do_idle+0x304/0x338
cpu_startup_entry+0x24/0x40
rest_init+0xf8/0x10c
arch_call_rest_init+0xc/0x14
start_kernel+0x774/0x7b4
Allocated by task 263:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
rsa_edesc_alloc+0x2cc/0xe10
caam_rsa_enc+0x9c/0x5f0
test_akcipher_one+0x78c/0x968
alg_test_akcipher+0x78/0xf8
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
save_stack+0x24/0xb0
__kasan_slab_free+0x10c/0x188
kasan_slab_free+0x10/0x18
kfree+0x7c/0x298
rsa_pub_done+0x68/0xe8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
The buggy address belongs to the object at ffff000023082000
which belongs to the cache dma-kmalloc-256 of size 256
The buggy address is located 20 bytes inside of
256-byte region [ffff000023082000, ffff000023082100)
The buggy address belongs to the page:
page:fffffe00006c2080 refcount:1 mapcount:0 mapping:ffff00093200c200 index:0x0 compound_mapcount: 0
flags: 0xffff00000010200(slab|head)
raw: 0ffff00000010200 dead000000000100 dead000000000122 ffff00093200c200
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff000023081f00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff000023081f80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff000023082000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff000023082080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff000023082100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: bf53795025a2 ("crypto: caam - add crypto_engine support for RSA algorithms")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Here's the KASAN report:
BUG: KASAN: use-after-free in ahash_done+0xdc/0x3b8
Read of size 1 at addr ffff00002303f010 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc1-00162-gfcb90d5 #59
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load1+0x5c/0x68
ahash_done+0xdc/0x3b8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
irq_exit+0x114/0x128
__handle_domain_irq+0x80/0xe0
gic_handle_irq+0x50/0xa0
el1_irq+0xb8/0x180
cpuidle_enter_state+0xa4/0x490
cpuidle_enter+0x48/0x70
call_cpuidle+0x44/0x70
do_idle+0x304/0x338
cpu_startup_entry+0x24/0x40
rest_init+0xf8/0x10c
arch_call_rest_init+0xc/0x14
start_kernel+0x774/0x7b4
Allocated by task 263:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
ahash_edesc_alloc+0x58/0x1f8
ahash_final_no_ctx+0x94/0x6e8
ahash_final+0x24/0x30
crypto_ahash_op+0x58/0xb0
crypto_ahash_final+0x30/0x40
do_ahash_op+0x2c/0xa0
test_ahash_vec_cfg+0x894/0x9e0
test_hash_vec_cfg+0x6c/0x88
test_hash_vec+0xfc/0x1e0
__alg_test_hash+0x1ac/0x368
alg_test_hash+0xf8/0x1c8
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
save_stack+0x24/0xb0
__kasan_slab_free+0x10c/0x188
kasan_slab_free+0x10/0x18
kfree+0x7c/0x298
ahash_done+0xd4/0x3b8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
The buggy address belongs to the object at ffff00002303f000
which belongs to the cache dma-kmalloc-128 of size 128
The buggy address is located 16 bytes inside of
128-byte region [ffff00002303f000, ffff00002303f080)
The buggy address belongs to the page:
page:fffffe00006c0fc0 refcount:1 mapcount:0 mapping:ffff00093200c000 index:0x0
flags: 0xffff00000000200(slab)
raw: 0ffff00000000200 dead000000000100 dead000000000122 ffff00093200c000
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff00002303ef00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff00002303ef80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff00002303f000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff00002303f080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff00002303f100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 21b014f038d3 ("crypto: caam - add crypto_engine support for HASH algorithms")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Here's the KASAN report:
BUG: KASAN: use-after-free in aead_crypt_done+0x60/0xd8
Read of size 1 at addr ffff00002303f014 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc1-00162-gfcb90d5 #58
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load1+0x5c/0x68
aead_crypt_done+0x60/0xd8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
irq_exit+0x114/0x128
__handle_domain_irq+0x80/0xe0
gic_handle_irq+0x50/0xa0
el1_irq+0xb8/0x180
_raw_spin_unlock_irq+0x2c/0x78
finish_task_switch+0xa4/0x2f8
__schedule+0x3a4/0x890
schedule_idle+0x28/0x50
do_idle+0x22c/0x338
cpu_startup_entry+0x24/0x40
rest_init+0xf8/0x10c
arch_call_rest_init+0xc/0x14
start_kernel+0x774/0x7b4
Allocated by task 263:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
aead_edesc_alloc+0x1b4/0xbf0
ipsec_gcm_encrypt+0xd4/0x140
crypto_aead_encrypt+0x50/0x68
test_aead_vec_cfg+0x498/0xec0
test_aead_vec+0x110/0x200
alg_test_aead+0xfc/0x680
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
save_stack+0x24/0xb0
__kasan_slab_free+0x10c/0x188
kasan_slab_free+0x10/0x18
kfree+0x7c/0x298
aead_crypt_done+0x58/0xd8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
The buggy address belongs to the object at ffff00002303f000
which belongs to the cache dma-kmalloc-128 of size 128
The buggy address is located 20 bytes inside of
128-byte region [ffff00002303f000, ffff00002303f080)
The buggy address belongs to the page:
page:fffffe00006c0fc0 refcount:1 mapcount:0 mapping:ffff00093200c000 index:0x0
flags: 0xffff00000000200(slab)
raw: 0ffff00000000200 dead000000000100 dead000000000122 ffff00093200c000
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff00002303ef00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff00002303ef80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff00002303f000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff00002303f080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff00002303f100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 1c2402266713 ("crypto: caam - add crypto_engine support for AEAD algorithms")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Here's the KASAN report:
BUG: KASAN: use-after-free in skcipher_crypt_done+0xe8/0x1a8
Read of size 1 at addr ffff00002304001c by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc1-00162-gfcb90d5 #57
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x260
show_stack+0x14/0x20
dump_stack+0xe8/0x144
print_address_description.isra.11+0x64/0x348
__kasan_report+0x11c/0x230
kasan_report+0xc/0x18
__asan_load1+0x5c/0x68
skcipher_crypt_done+0xe8/0x1a8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
irq_exit+0x114/0x128
__handle_domain_irq+0x80/0xe0
gic_handle_irq+0x50/0xa0
el1_irq+0xb8/0x180
_raw_spin_unlock_irq+0x2c/0x78
finish_task_switch+0xa4/0x2f8
__schedule+0x3a4/0x890
schedule_idle+0x28/0x50
do_idle+0x22c/0x338
cpu_startup_entry+0x24/0x40
rest_init+0xf8/0x10c
arch_call_rest_init+0xc/0x14
start_kernel+0x774/0x7b4
Allocated by task 263:
save_stack+0x24/0xb0
__kasan_kmalloc.isra.10+0xc4/0xe0
kasan_kmalloc+0xc/0x18
__kmalloc+0x178/0x2b8
skcipher_edesc_alloc+0x21c/0x1018
skcipher_encrypt+0x84/0x150
crypto_skcipher_encrypt+0x50/0x68
test_skcipher_vec_cfg+0x4d4/0xc10
test_skcipher_vec+0xf8/0x1d8
alg_test_skcipher+0xec/0x230
alg_test.part.44+0x114/0x4a0
alg_test+0x1c/0x60
cryptomgr_test+0x34/0x58
kthread+0x1b8/0x1c0
ret_from_fork+0x10/0x18
Freed by task 0:
save_stack+0x24/0xb0
__kasan_slab_free+0x10c/0x188
kasan_slab_free+0x10/0x18
kfree+0x7c/0x298
skcipher_crypt_done+0xe0/0x1a8
caam_jr_dequeue+0x390/0x608
tasklet_action_common.isra.13+0x1ec/0x230
tasklet_action+0x24/0x30
efi_header_end+0x1a4/0x370
The buggy address belongs to the object at ffff000023040000
which belongs to the cache dma-kmalloc-512 of size 512
The buggy address is located 28 bytes inside of
512-byte region [ffff000023040000, ffff000023040200)
The buggy address belongs to the page:
page:fffffe00006c1000 refcount:1 mapcount:0 mapping:ffff00093200c400 index:0x0 compound_mapcount: 0
flags: 0xffff00000010200(slab|head)
raw: 0ffff00000010200 dead000000000100 dead000000000122 ffff00093200c400
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff00002303ff00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff00002303ff80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff000023040000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff000023040080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff000023040100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: ee38767f152a ("crypto: caam - support crypto_engine framework for SKCIPHER algorithms")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add missing module firmware for turings.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CACAvsv4njTRpiNqOC54iRjpd=nu3pBG8i_fp8o_dp7AZE6hFWA@mail.gmail.com
|
|
ASB was failing to load on Turing GPUs when firmware is being loaded
from initramfs, leaving the GPU in an odd state and causing suspend/
resume to fail.
Add missing MODULE_FIRMWARE() lines for initramfs generators.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 5.6
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.7-2020-04-15:
amdgpu:
- gfx10 fix
- SMU7 overclocking fix
- RAS fix
- GPU reset fix
- Fix a regression in a previous s/r fix
- Add a gfxoff quirk
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415221631.3924-1-alexander.deucher@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Misc EFI fixes, including the boot failure regression caused by the
BSS section not being cleared by the loaders"
* tag 'efi-urgent-2020-04-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Revert struct layout change to fix kexec boot regression
efi/x86: Don't remap text<->rodata gap read-only for mixed mode
efi/x86: Fix the deletion of variables in mixed mode
efi/libstub/file: Merge file name buffers to reduce stack usage
Documentation/x86, efi/x86: Clarify EFI handover protocol and its requirements
efi/arm: Deal with ADR going out of range in efi_enter_kernel()
efi/x86: Always relocate the kernel for EFI handover entry
efi/x86: Move efi stub globals from .bss to .data
efi/libstub/x86: Remove redundant assignment to pointer hdr
efi/cper: Use scnprintf() for avoiding potential buffer overflow
|
|
Fix the following sparse warning:
drivers/net/ethernet/dec/tulip/tulip_core.c:1280:28: warning: symbol
'early_486_chipsets' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To rehash a previous explanation given in commit 1c44ce560b4d ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.
The configuration for this native VLAN is driven in 2 ways:
- Set the egress port rewriter to strip the VLAN tag for the native
VID (as it is egress-untagged, after all).
- Configure the ingress port to drop untagged and priority-tagged
traffic, if there is no native VLAN. The intention of this setting is
that a trunk port with no native VLAN should not accept untagged
traffic.
Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.
But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
- Native VLAN of the port - its value is held in port->vid.
- VLAN awareness state of the port - currently there are some issues
here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
0. The driver configures a pvid of zero for each port, when in
standalone mode. While the bridge configures a default_pvid of 1 for
each port that gets added as a slave to it.
1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
The VLAN-filtering-dependent portion of the native VLAN
configuration is done, considering that the native VLAN is 0.
2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
untagged=true. The native VLAN changes to 1 (change which gets
propagated to hardware).
3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
VLAN-filtering-dependent portion of the native VLAN configuration,
for the new native VLAN of 1. One can notice that after toggling "ip
link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
type bridge vlan_filtering 1", the new native VLAN finally makes it
through and untagged traffic finally starts flowing again. But
obviously that shouldn't be needed.
So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.
*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
- Ocelot: ocelot_port_private->vlan_aware
- Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.
Fixes: 97bb69e1e36e ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of fixes:
* FTM responder policy netlink validation fix
(but the only user validates again later)
* kernel-doc fixes
* a fix for a race in mac80211 radio registration vs. userspace
* a mesh channel switch fix
* a fix for a syzbot reported kasprintf() issue
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DMA transfer could be completed, but CPU (which handles DMA interrupt)
may get too busy and can't handle the interrupt in a timely manner,
despite of DMA IRQ being raised. In this case the DMA state needs to
synchronized before terminating DMA transfer in order not to miss the
DMA transfer completion.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Boot CPU0 always handle I2C interrupt and under some rare circumstances
(like running KASAN + NFS root) it may stuck in uninterruptible state for
a significant time. In this case we will get timeout if I2C transfer is
running on a sibling CPU, despite of IRQ being raised. In order to handle
this rare condition, the IRQ status needs to be checked after completion
timeout.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The DMA transfer might finish just after checking the state with
dma_cookie_status, but before the lock is acquired. Not checking
for an empty list in xilinx_dma_tx_status may result in reading
random data or data corruption when desc is written to. This can
be reliably triggered by using dma_sync_wait to wait for DMA
completion.
Signed-off-by: Sebastian von Ohr <vonohr@smaract.com>
Tested-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20200303130518.333-1-vonohr@smaract.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The mutex_unlock() is missed on error path of psil_get_ep_config()
which causes deadlock, so add missed mutex_unlock().
Fixes: 8c6bb62f6b4a ("dmaengine: ti: k3 PSI-L remote endpoint configuration")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200408185501.30776-1-grygorii.strashko@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If PCI_MSI is not set, building fais:
drivers/dma/hisi_dma.c: In function ‘hisi_dma_free_irq_vectors’:
drivers/dma/hisi_dma.c:138:2: error: implicit declaration of function ‘pci_free_irq_vectors’;
did you mean ‘pci_alloc_irq_vectors’? [-Werror=implicit-function-declaration]
pci_free_irq_vectors(data);
^~~~~~~~~~~~~~~~~~~~
Make HISI_DMA depends on PCI_MSI to fix this.
Fixes: e9f08b65250d ("dmaengine: hisilicon: Add Kunpeng DMA engine support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200328114133.17560-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
siw_fastreg_mr() invokes siw_mem_id2obj(), which returns a local reference
of the siw_mem object to "mem" with increased refcnt. When
siw_fastreg_mr() returns, "mem" becomes invalid, so the refcount should be
decreased to keep refcount balanced.
The issue happens in one error path of siw_fastreg_mr(). When "base_mr"
equals to NULL but "mem" is not NULL, the function forgets to decrease the
refcnt increased by siw_mem_id2obj() and causes a refcnt leak.
Reorganize the flow so that the goto unwind can be used as expected.
Fixes: b9be6f18cf9e ("rdma/siw: transmit path")
Link: https://lore.kernel.org/r/1586939949-69856-1-git-send-email-xiyuyang19@fudan.edu.cn
Reported-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
HID_DEVICE_ID_ALPS_1657 PID is too specific, as there are many other
ALPS hardware IDs using this particular touchpad.
Rename the identifier to HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY in order
to describe reality better.
Fixes: 640e403b1fd24 ("HID: alps: Add AUI1657 device ID")
Reported-by: Xiaojian Cao <xiaojian.cao@cn.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
All in-tree users have been converted to the new i2c_new_scanned_device
function, so remove this deprecated one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
device_property_read_u32() returns errno or 0, so we should use the
integer variable 'ret' and not the u32 'val' to hold the retval.
Fixes: 0560ad576268 ("i2c: altera: Add Altera I2C Controller driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We already set DPM_FLAG_SMART_PREPARE, so we completely skip all
callbacks (other then prepare) where possible, quoting from
dw_i2c_plat_prepare():
/*
* If the ACPI companion device object is present for this device, it
* may be accessed during suspend and resume of other devices via I2C
* operation regions, so tell the PM core and middle layers to avoid
* skipping system suspend/resume callbacks for it in that case.
*/
return !has_acpi_companion(dev);
Also setting the DPM_FLAG_SMART_SUSPEND will cause acpi_subsys_suspend()
to leave the controller runtime-suspended even if dw_i2c_plat_prepare()
returned 0.
Leaving the controller runtime-suspended normally, when the I2C controller
is suspended during the suspend_late phase, is not an issue because
the pm_runtime_get_sync() done by i2c_dw_xfer() will (runtime-)resume it.
But for dw I2C controllers on Bay- and Cherry-Trail devices acpi_lpss.c
leaves the controller alive until the suspend_noirq phase, because it may
be used by the _PS3 ACPI methods of PCI devices and PCI devices are left
powered on until the suspend_noirq phase.
Between the suspend_late and resume_early phases runtime-pm is disabled.
So for any ACPI I2C OPRegion accesses done after the suspend_late phase,
the pm_runtime_get_sync() done by i2c_dw_xfer() is a no-op and the
controller is left runtime-suspended.
i2c_dw_xfer() has a check to catch this condition (rather then waiting
for the I2C transfer to timeout because the controller is suspended).
acpi_subsys_suspend() leaving the controller runtime-suspended in
combination with an ACPI I2C OPRegion access done after the suspend_late
phase triggers this check, leading to the following error being logged
on a Bay Trail based Lenovo Thinkpad 8 tablet:
[ 93.275882] i2c_designware 80860F41:00: Transfer while suspended
[ 93.275993] WARNING: CPU: 0 PID: 412 at drivers/i2c/busses/i2c-designware-master.c:429 i2c_dw_xfer+0x239/0x280
...
[ 93.276252] Workqueue: kacpi_notify acpi_os_execute_deferred
[ 93.276267] RIP: 0010:i2c_dw_xfer+0x239/0x280
...
[ 93.276340] Call Trace:
[ 93.276366] __i2c_transfer+0x121/0x520
[ 93.276379] i2c_transfer+0x4c/0x100
[ 93.276392] i2c_acpi_space_handler+0x219/0x510
[ 93.276408] ? up+0x40/0x60
[ 93.276419] ? i2c_acpi_notify+0x130/0x130
[ 93.276433] acpi_ev_address_space_dispatch+0x1e1/0x252
...
So since on BYT and CHT platforms we want ACPI I2c OPRegion accesses
to work until the suspend_noirq phase, we need the controller to be
runtime-resumed during the suspend phase if it is runtime-suspended
suspended at that time. This means that we must not set the
DPM_FLAG_SMART_SUSPEND on these platforms.
On BYT and CHT we already have a special ACCESS_NO_IRQ_SUSPEND flag
to make sure the controller stays functional until the suspend_noirq
phase. This commit makes the driver not set the DPM_FLAG_SMART_SUSPEND
flag when that flag is set.
Cc: stable@vger.kernel.org
Fixes: b30f2f65568f ("i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We are racing to initialize sched->thread here, just always check the
current thread.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Link: https://patchwork.freedesktop.org/patch/361303/
|
|
Fix the following sparse warning:
drivers/firmware/xilinx/zynqmp-debug.c:38:15: warning: symbol
'firmware_debugfs_root' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200415084311.24857-1-yanaijie@huawei.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The function “platform_get_irq” can log an error already.
Thus omit a redundant message for the exception handling in the
calling function.
This issue was detected by using the Coccinelle software.
Fixes: 3f68be7d8e96 ("drm/meson: Add support for HDMI encoder and DW-HDMI bridge + PHY")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/76f24122-4d3f-7670-9f06-edb4731a0661@web.de
|
|
The firmware driver is optional, but the power driver depends on it,
which needs to be reflected in Kconfig to avoid link errors:
aarch64-linux-ld: drivers/soc/xilinx/zynqmp_power.o: in function `zynqmp_pm_isr':
zynqmp_power.c:(.text+0x284): undefined reference to `zynqmp_pm_invoke_fn'
The firmware driver can probably be allowed for compile-testing as
well, so it's best to drop the dependency on the ZYNQ platform
here and allow building as long as the firmware code is built-in.
Fixes: ab272643d723 ("drivers: soc: xilinx: Add ZynqMP PM driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200408155224.2070880-1-arnd@arndb.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Link: https://lore.kernel.org/r/20200413170501.13381-1-flameeyes@flameeyes.com
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the __copy_from_user function failed we need to call sg_remove_request
in sg_write.
Link: https://lore.kernel.org/r/610618d9-e983-fd56-ed0f-639428343af7@huawei.com
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Some Google Apex Edge TPU devices have a class code of 0
(PCI_CLASS_NOT_DEFINED). This prevents the PCI core from assigning
resources for the Apex BARs because __dev_sort_resources() ignores
classless devices, host bridges, and IOAPICs.
On x86, firmware typically assigns those resources, so this was not a
problem. But on some architectures, firmware does *not* assign BARs, and
since the PCI core didn't do it either, the Apex device didn't work
correctly:
apex 0000:01:00.0: can't enable device: BAR 0 [mem 0x00000000-0x00003fff 64bit pref] not claimed
apex 0000:01:00.0: error enabling PCI device
f390d08d8b87 ("staging: gasket: apex: fixup undefined PCI class") added a
quirk to fix the class code, but it was in the apex driver, and if the
driver was built as a module, it was too late to help.
Move the quirk to the PCI core, where it will always run early enough that
the PCI core will assign resources if necessary.
Link: https://lore.kernel.org/r/CAEzXK1r0Er039iERnc2KJ4jn7ySNUOG9H=Ha8TD8XroVqiZjgg@mail.gmail.com
Fixes: f390d08d8b87 ("staging: gasket: apex: fixup undefined PCI class")
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Debugged-by: Luís Mendes <luis.p.mendes@gmail.com>
Tested-by: Luis Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Todd Poynor <toddpoynor@google.com>
|
|
Soft-reset the PHY when coming out of low power mode, which seems to
be necessary with firmware versions 0.3.3.0 and 0.3.10.0.
This depends on ("net: marvell10g: report firmware version")
Fixes: c9cc1c815d36 ("net: phy: marvell10g: place in powersave mode at probe")
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report the firmware version when probing the PHY to allow issues
attributable to firmware to be diagnosed.
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Positive return values are also failures that don't set val,
although this probably can't happen. Fixes gcc 10 warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
3747 | *phy_fw_ver = val;
Fixes: 01b6961410b7 ("cxgb4: Add PHY firmware support for T420-BT cards")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize ib_spec on the stack before using it, otherwise we will have
garbage values that will break creating default rules with invalid parsing
error.
Fixes: a37a1a428431 ("IB/mlx4: Add mechanism to support flow steering over IB links")
Link: https://lore.kernel.org/r/20200413132235.930642-1-leon@kernel.org
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Allow all the RGMII modes to be used. (Not only "rgmii", "rgmii-id"
but "rgmii-txid", "rgmii-rxid")
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88e6185 is reporting it has detected a PHY, when a port is
connected to an SFP. As a result, the fixed-phy configuration is not
being applied. That then breaks packet transfer, since the port is
reported as being down.
Add additional conditions to check the interface mode, and if it is
fixed always configure the port on link up/down, independent of the
PPU status.
Fixes: 30c4a5b0aad8 ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove an unused initialized value.
Fixes: 7e4d47596b68 ("ionic: replay filters after fw upgrade")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the appropriate header for using dynamic_hex_dump(), which
seems to be incidentally included in some configurations but
not all.
Fixes: 7e4d47596b68 ("ionic: replay filters after fw upgrade")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ9131 will not work with some switches due to workaround for KSZ9031
introduced in commit d2fd719bcb0e83cb39cfee22ee800f98a56eceb3
("net/phy: micrel: Add workaround for bad autoneg").
Use genphy_read_status instead of dedicated ksz9031_read_status.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the hibernation patchset (e.g. f53335e3289f), in a Generation-2
Linux VM on Hyper-V, the user can run "echo freeze > /sys/power/state" to
freeze the system, i.e. Suspend-to-Idle. The user can press the keyboard
or move the mouse to wake up the VM.
With the hibernation patchset, Linux VM on Hyper-V can hibernate to disk,
but Suspend-to-Idle is broken: when the synthetic keyboard/mouse are
suspended, there is no way to wake up the VM.
Fix the issue by not suspending and resuming the vmbus devices upon
Suspend-to-Idle.
Fixes: f53335e3289f ("Drivers: hv: vmbus: Suspend/resume the vmbus itself for hibernation")
Cc: stable@vger.kernel.org
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1586663435-36243-1-git-send-email-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.7
First set of fixes for v5.6. Fixes for a crash and for two compiler
warnings.
brcmfmac
* fix a crash related to monitor interface
ath11k
* fix compiler warnings without CONFIG_THERMAL
rtw88
* fix compiler warnings related to suspend and resume functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xa_alloc_cyclic_irq() function returns either 0 or 1 on success and
negatives on error. This code treats 1 as an error and returns ERR_PTR(1)
which will cause an Oops in the caller.
Fixes: ae78ff3a0f0c ("RDMA/cm: Convert local_id_table to XArray")
Link: https://lore.kernel.org/r/20200407093714.GA80285@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- a series from Tianyu Lan to fix crash reporting on Hyper-V
- three miscellaneous cleanup patches
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/Hyper-V: Report crash data in die() when panic_on_oops is set
x86/Hyper-V: Report crash register data when sysctl_record_panic_msg is not set
x86/Hyper-V: Report crash register data or kmsg before running crash kernel
x86/Hyper-V: Trigger crash enlightenment only once during system crash.
x86/Hyper-V: Free hv_panic_page when fail to register kmsg dump
x86/Hyper-V: Unload vmbus channel in hv panic callback
x86: hyperv: report value of misc_features
hv_debugfs: Make hv_debug_root static
hv: hyperv_vmbus.h: Replace zero-length array with flexible-array member
|
|
The cm_reset_to_idle() call before formatting event changed the CM_ID
state from IB_CM_REQ_RCVD to be IB_CM_IDLE. It caused to wrong value of
CM_REJ_MESSAGE_REJECTED field.
The result of that was that rdma_reject() calls in the passive side didn't
generate RDMA_CM_EVENT_REJECTED event in the active side.
Fixes: 81ddb41f876d ("RDMA/cm: Allow ib_send_cm_rej() to be done under lock")
Link: https://lore.kernel.org/r/20200406173242.1465911-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
