summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-03-27pinctrl: tegra: Renumber the GG.0 and GG.1 pinsThierry Reding
There is no need to define these at a specific offset since they are the only pins defined for this SoC generation. Begin numbering them at 0. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200319122737.3063291-9-thierry.reding@gmail.com Tested-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27pinctrl: tegra: Do not add default pin range on Tegra194Thierry Reding
On Tegra194, almost all of the pin control programming happens in early boot firmware, so there is no use in having a pin range defined for all the pins. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200319122737.3063291-8-thierry.reding@gmail.com Tested-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27pinctrl: tegra: Pass struct tegra_pmx for pin range checkThierry Reding
Pass the struct tegra_pmx when checking for the pin range in device tree. This makes the call site a bit easier to read and will help keep that readability in a subsequent patch. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200319122737.3063291-7-thierry.reding@gmail.com Tested-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27pinctrl: tegra: Fix "Scmitt" -> "Schmitt" typoThierry Reding
Properly spell "Schmitt" in the kerneldoc for pin group definitions. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200319122737.3063291-6-thierry.reding@gmail.com Tested-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27pinctrl: tegra: Fix whitespace issues for improved readabilityThierry Reding
Fix a few whitespace inconsistencies to make the code easier to read. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200319122737.3063291-5-thierry.reding@gmail.com Tested-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27gpio: tegra186: Add Tegra194 pin ranges for GG.0 and GG.1Thierry Reding
The GG.0 and GG.1 GPIOs serve as CLKREQ and RST pins, respectively, for PCIe controller 5 on Tegra194. When this controller is configured in endpoint mode, these pins need to be used as GPIOs by the PCIe endpoint driver. Typically the mode programming of these pins (GPIO vs. SFIO) is performed by early boot firmware to ensure that the configuration is consistent. However, the GG.0 and GG.1 pins are part of a special power partition that is not enabled during early boot, and hence the early boot firmware cannot program these pins to be GPIOs (they are SFIO by default). Adding them as pin ranges for the pin controller allows the pin controller to be involved when these pins are requested as GPIOs and allows the proper programming to take place. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200319122737.3063291-4-thierry.reding@gmail.com Tested-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27gpio: tegra186: Add support for pin rangesThierry Reding
Add support for Tegra SoC generations to specify a list of pin ranges that map GPIOs to ranges of pins in the pin controller. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200319122737.3063291-3-thierry.reding@gmail.com Tested-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27gpio: Support GPIO controllers without pin-rangesThierry Reding
Wake gpiochip_generic_request() call into the pinctrl helpers only if a GPIO controller had any pin-ranges assigned to it. This allows a driver to unconditionally use this helper if it supports multiple devices of which only a subset have pin-ranges assigned to them. Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200319122737.3063291-2-thierry.reding@gmail.com Tested-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27pinctrl: mediatek: Use scnprintf() for avoiding potential buffer overflowTakashi Iwai
Since snprintf() returns the would-be-output size instead of the actual output size, the succeeding calls may go beyond the given buffer limit. Fix it by replacing with scnprintf(). Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200311090644.20287-1-tiwai@suse.de Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-27s390/qdio: set qdio_irq->cdev at allocation timeJulian Wiedmann
Set up qdio_irq->cdev right when the qdio_irq struct is allocated, so that all subsequent code can rely on this pointer. Then convert two helper functions to not pass a cdev parameter around. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
2020-03-27s390/qdio: remove unused function declarationsJulian Wiedmann
commit 50f769df1c4b ("[S390] qdio: improve inbound buffer acknowledgement") introduced these declarations, but noone added the actual code for them. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
2020-03-27s390/ccwgroup: remove pm supportJulian Wiedmann
As s390 no longer supports ARCH_HIBERNATION_POSSIBLE, drop the unused pm ops from the ccwgroup bus driver. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
2020-03-27s390/ap: remove power management code from ap bus and driversHarald Freudenberger
The s390 power management support has been removed. So the api registration and the suspend and resume callbacks and all the code related to this for the ap bus and the ap drivers is removed with this patch. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
2020-03-27s390/zcrypt: use kvmalloc instead of kmalloc for 256k allocHarald Freudenberger
Tests showed that it may happen that a 256k kmalloc may fail due to a temporary shortage on 256k slab entries. The find functions for cca and ep11 use a 256k array to fetch the states of all possible crypto cards and their domains in one piece. With the patch now kvmalloc is used to allocate this temporary memory as there is no need to have this memory area physical continuously. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
2020-03-27s390/ism: remove pm supportUrsula Braun
As s390 no longer supports ARCH_HIBERNATION_POSSIBLE, drop the unused pm ops from the ism driver. Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
2020-03-27staging: vt6656: Use DIV_ROUND_UP macro instead of specific codeOscar Carter
Use DIV_ROUND_UP macro instead of specific code with the same purpose. Also, remove the unused variables. Signed-off-by: Oscar Carter <oscar.carter@gmx.com> Reviewed-by: Quentin Deslandes <quentin.deslandes@itdev.co.uk> Link: https://lore.kernel.org/r/20200326175902.14467-1-oscar.carter@gmx.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-27staging: remove hp100 driverGreg Kroah-Hartman
It's old, obsolete, and no one wants to take care of it anymore. It's been in staging for 5 months with no one paying attention to it, so let's just delete it for now. If someone has this hardware, and wants the driver back, the deletion can be easily reverted. Cc: Joe Perches <joe@perches.com> Cc: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20200326080233.978323-1-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-27iwlwifi: mvm: remove newline from rs_pretty_print_rate()Johannes Berg
Some of the places using this want the newline, but not all, so remove the newline from it and generate it in the debugfs files where it's desired. The effect of this is not printing double newlines in debug log messages. Change-Id: Ia59b0abbef16b6783fcabc095c5fde16bd047a26 Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: pcie: make iwl_pcie_cmdq_reclaim staticJohannes Berg
There's no need for this to be exposed outside of the tx.c file, make it static. Change-Id: I41d40008311b108d0578bd2ec73c5477e700a839 Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: bump FW API to 53 for 22000 seriesLuca Coelho
Start supporting API version 53 for 22000 series. Change-Id: I5725e46394f3f53c3069723fd513cc53c7df383d Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: remove IWL_FW_DBG_DOMAIN macroJohannes Berg
This is used to initialize the default value, but refers back to the value itself, essentially leading to a val = val assignment at init time ... that's useless, remove it and use _NODEF. Change-Id: I725923016563c34ce2fa057bf7c12984e1041c49 Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: yoyo: enable yoyo by defaultLuca Coelho
Now that YoYo is more mature, we can enable it by default, so we collect data in the new way. Change-Id: Ic1a147f935286b085ca8bdb248a7493b7c6341ea Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: scan: support FW APIs with variable number of profilesTova Mussai
The FW changed the maximum number of scan offload profiles to 8 in new APIs. Support it by changing the scan_offload_profile_cfg struct to be more dynamic, so we can reuse most of the code and only change size of the profiles array. Change-Id: I65210cf541af46e2675a8c764d5871f7f5b070d6 Signed-off-by: Tova Mussai <tova.mussai@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: yoyo: don't block dumping internal memory when not in SRAM moderotem saado
When we have an assert during D3 we want to dump the internal buffer memory even if are we working in DRAM debug mode. We should not block dumping it. Change-Id: I69aad2d4904c4f8bb653c61e8781a2e07780054f Signed-off-by: Rotem Saado <rotem.saado@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: remove support for QnJ HR FPGALuca Coelho
We don't support the FPGA versions of this card combination anymore. Remove the cfg mangling that tries to load it and all the relevant structures. Change-Id: I190652101afcab682cfba873d062992f11efca32 Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: remove support for QnJ Hr STEP ALuca Coelho
We don't support QnJ HR STEP A anymore. Remove the structures we used for it. Change-Id: I0dfd88232bdc8ff2dd9c4368b8ed9a0c40c86bc8 Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: add trans_cfg for devices with long latencyLuca Coelho
A couple of SoCs, which can be recognized by PCI device IDs 0xA0F0 and 0x43F0, need a longer wait for the xtal to stabilize. To handle this, add a new trans_cfg structure for Qu devices with a larger xtal_latency value and apply them to the devices recognized by these IDs. Also add a flag that allows us to inform the FW that the low latency xtal should be used. Change-Id: I8a14c6af45ea14d8e7f1ef38a589158f38d0c0ea Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: add support for version 2 of SOC_CONFIGURATION_CMDLuca Coelho
This new command is mostly backwards compatible, with the exception that the device_type element was changed into a bitmask. The device type bit remains the same (because we only had 0 and 1 anyway), but when using v1 we can't set any other bits, because that would change the integer. Other than that, the struct remains the same and the driver can set the device_type bit in both cases, but it can only set the low_latency bit if VER_2 is used. Change-Id: Ib68d4c821ebcce253b42ed0ea15881fb4e3e01da Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: mvm: add support for non EDCA based measurementsAvraham Stern
Add support for requesting trigger-based / non trigger-based measurements. Change-Id: Ib4d0c471da9c50d9981541a7f5926db384a0f7ce Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: remove unnecessary cfg mangling for Qu C and QuZ with JfLuca Coelho
Now that we identify the correct cfgs with the new tables for Qu step C and QuZ with Jf, we can remove the mangling we do later on. Change-Id: Ic01ce67db147e897ad2424f0e05a70a00d2c620e Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: convert QnJ with Jf devices to new config tableLuca Coelho
All the QnJ devices have a similar matching to the other Qu devices, but needs a different configuration. Convert the QnJ devices to the new table accordingly. Change-Id: If236ef3d0da3e605a3379922818f5897e0affd7e Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: convert all Qu with Jf devices to the new config tableLuca Coelho
Add new generic iwl_trans structures for these devices and apply the correct cfg depending on the device characteristics. Since we have to match Qu with IWL_CONFIG_ANY, we also need to move the Hr devices to the new table, but for now we keep matching on PCI device and subsystem device IDs. Change-Id: I14e9146a99621ff11ce50bc746a4b88af508fee0 Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: add HW step to new cfg device tableLuca Coelho
We need to use different firmware versions for different HW steps with certain devices. Prepare for this differentiation by adding HW step to the new device table. Change-Id: Ib1afb7b0c89e9dc2d26e6d32ea19e978c17ba1dd Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: remove some unused extern declarations from iwl-config.hLuca Coelho
After the refactoring, a few extern declarations were accidentally left in the iwl-config.h file. Remove them Change-Id: I79745e440ed5a0a90db61b0daaae374ecef09e86 Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: move integrated, extra_phy and soc_latency to trans_cfgLuca Coelho
These values are selected based on the PCI device ID, so the decision to use them can be made early. By moving them to the trans_cfg, we avoid duplicating the large cfg structs for small pieces of data (sometimes a single boolean). This will also allow us to make more decisions based on, for instance, the SoC type in used. The trans_cfg concept changes a bit, because previously it was used only to boot the device before reading further characteristics and now it also contains more data that is associated with the device ID. Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: mvm: enable SF also when we have HEJohannes Berg
We shouldn't do this just for HT/VHT, but be future-proof and also check for HE. Change-Id: Icaeff714c00a773681dbfee72558afd1c7121c5d Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: remove redundant iwl9560_2ac_cfg structLuca Coelho
The iwl9560_2ac_cfg struct is used for PNJ devices and the configuration is the same as iwl9260_2ac_cfg, so we can remove the former to avoid redundancy. Change-Id: I17ac1802f00bd80006930b922a9fc21df60e3c16 Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: mvm: rs-fw: fix some indentationJohannes Berg
That closing brace for the switch statement is misplaced, fix it. Change-Id: I39af135a9e3fc64337d2cced43a70cb48fe3b9c1 Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: scan: support scan req cmd ver 14Shahar S Matityahu
Modify adaptive dwell number of APs override API Instead of using channel to index mapping, add the adaptive dwell override parameters as part of the configuration per channel in the scan request command. Support 2 different override values and use them as follows: 1. 10 APs for friendly GO channels in p2p scan. 2. 2 APs for social channels in p2p scan. Change-Id: I3b461108abf2306c3d054099112f2c3afce1cc92 Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: pass trans and NVM data to HE capability parsingJohannes Berg
We'll need this data in the future, pass the values. Change-Id: Iaeff50716e783f5c0bcea86ca1c93ada1560525e Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: pcie: implement read_config32Luca Coelho
Add the read_config32 op to allow dumping the config space when needed. Change-Id: Ib2d254a38a4bfb95dcc3d04eec91781827a0c623 Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: yoyo: add PCI config space region typeLuca Coelho
Add a new region type that allows us to dump the PCI config space. This is mostly the same as dumping a memory region, but reading from the device's config space instead. In order to make this generic and independent of the trans type, we make a function called iwl_dump_ini_config_iter() that calls a new op in the transport to read its config space. Change-Id: I15151bddf589f13b0e0a45c28b96bbcd73bcfdeb Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-27iwlwifi: mvm: add soc latency supportShahar S Matityahu
Some devices require longer time to stabilize the power and XTAL. This is especially true for devices integrated in the SoC. Add support for a new firmware API that allows the driver to set the latency value accordingly. Change-Id: I6829a46b89e4e701f80a0e4033f4dd41ee44ed12 Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-03-26Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: - a fix to generate proper timestamps on key autorepeat events that were broken recently - a fix for Synaptics driver to only activate reduced reporting mode when explicitly requested - a new keycode for "selective screenshot" function - other assorted fixes * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: fix stale timestamp on key autorepeat events Input: move the new KEY_SELECTIVE_SCREENSHOT keycode Input: avoid BIT() macro usage in the serio.h UAPI header Input: synaptics-rmi4 - set reduced reporting mode only when requested Input: synaptics - enable RMI on HP Envy 13-ad105ng Input: allocate keycode for "Selective Screenshot" key Input: tm2-touchkey - add support for Coreriver TC360 variant dt-bindings: input: add Coreriver TC360 binding dt-bindings: vendor-prefixes: Add Coreriver vendor prefix Input: raydium_i2c_ts - fix error codes in raydium_i2c_boot_trigger()
2020-03-26net: phy: don't touch suspended flag if there's no suspend/resume callbackHeiner Kallweit
So far we set phydev->suspended to true in phy_suspend() even if the PHY driver doesn't implement the suspend callback. This applies accordingly for the resume path. The current behavior doesn't cause any issue I'd be aware of, but it's not logical and misleading, especially considering the description of the flag: "suspended: Set to true if this phy has been suspended successfully" Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-26net: ks8851-ml: Fix IO operations, againMarek Vasut
This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it turns out these were only necessary due to buggy hardware. This patch adds a check for such a buggy hardware to prevent any such mistakes again. While working further on the KS8851 driver, it came to light that the KS8851-16MLL is capable of switching bus endianness by a hardware strap, EESK pin. If this strap is incorrect, the IO accesses require such endian swapping as is being reverted by this patch. Such swapping also impacts the performance significantly. Hence, in addition to removing it, detect that the hardware is broken, report to user, and fail to bind with such hardware. Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access") Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-26net: atlantic: add XPN handlingMark Starovoytov
This patch adds XPN handling. Our driver doesn't support XPN, but we should still update a couple of places in the code, because the size of 'next_pn' field has changed. Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-26net: atlantic: MACSec offload statistics implementationDmitry Bogdanov
This patch adds support for MACSec statistics on Atlantic network cards. Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-26net: atlantic: MACSec offload statistics HW bindingsDmitry Bogdanov
This patch adds the Atlantic HW-specific bindings for MACSec statistics, e.g. register addresses / structs, helper function, etc, which will be used by actual callback implementations. Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-26net: atlantic: MACSec ingress offload implementationMark Starovoytov
This patch adds support for MACSec ingress HW offloading on Atlantic network cards. Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-21 23:39:28 +0000