| Age | Commit message (Collapse) | Author |
|---|
|
When driver is going to sleep, it does not leave LPS/IPS, thus the
BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex
needs to clear the IPS/LPS state when it receives a pnp notify, then
it can properly set up the hw when driver wakes up.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In the hardware initialisation stage, the PTA circuits may be unstable,
so we reset it after 6 secs to fix the problem.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These cases are for the btcoex to tune the performance
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If ap num < 10, let wifi and bt transmit simultaneously, otherwise set
wifi into standy when bt is transmitting
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The variable is for PS tdma duration adjust, so rename it to clearly
to specify its usage.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For time division multiple access, the wifi and bt take turns to
transmit, but we need to let AP know that wifi is under standby mode by
sending null data to "pretend" entering power saving state using lps
rpwm.
But, the fw does not know if it is the actual power saving mode or just a
fake one to cheat to the AP. Hence, before fw setting the tdma duration,
the fw needs the driver to check the power saving state first.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When receiving pno results there may be duplicate channels and/or
ssids. Assure each is added only once when preparing the internal
escan request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Checking whether the address of an array element is null is bogus
so removing it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Assure the event data buffer is long enough to hold the array
of netinfo items and that SSID length does not exceed the maximum
of 32 characters as per 802.11 spec.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The fwsignal module is part of the bcdc protocol and as such does
its instance data is not needed in core structure. Moving it into
struct brcmf_bcdc instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When brcmf_fws_add_interface() is called the struct brcmf_if::fws_desc
field is initialized regardless the state of the fwsignal functionality,
ie. the fcmode. This is not needed when fcmode is NONE, which is the
default mode.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a non-functional change to align the fwsignal module to
the naming pattern used throughout the driver.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Systems with 64 bit DMA at least partially require buffers to be used
for DMA to be 8-byte-aligned. One example is Amlogic Meson GX.
Switching the MMC/SDIO driver for this platform to SG DMA mode
resulted in problems due to unaligned buffers.
Fortunately the brcmfmac driver has a global define for the alignment.
Changing it to 8 fixed the issues with Meson GX.
Suggested-by: Helmut Klein <hgkr.klein@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We have to use start port, for TX/RX of single packet,
instead of current aggregating port. This will fix SDIO
CMD53(TX/RX) returning -ETIMEDOUT and halting the data path.
Fixes: 0cb52aac4d19 ("mwifiex: do not set multiport flag for tx/rx single packet")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The I2C device ID entries set a .driver_data but this data is never
looked up by the driver. So don't set it and also remove the enum.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In case wil6210 resume fails, wil6210 suspend function will try
to access the suspended device in the next kernel suspend.
To prevent that, add wil_status_suspended flag to indicate if the
device is already suspended and clear it only if the resume succeeds.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Array index 'i' is used before limits check.
Fix this by doing limits check first.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
debugfs ioblob function is called by the FW logs scripts
to copy the FW logs via PCIe.
As the FW logs collection is done in parallel to the operational
11AD actions, the HALP voting can take place during 11AD reset flow
and other sensitive scenarios.
To prevent that, remove HALP voting from the ioblob function.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is
a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Driver fails to load FW for sparrow D0 devices in some cases.
Fix this by returning correct value from wil_fw_verify_file_exists
when D0 FW file is not detected for any reason.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
During the suspend flow, wil6210 HW can send sporadic interrupts,
while PCIe bus is not operational.
To prevent that, keep the interrupts disabled during the suspend
flow and re-enable them only after PCIe enablement in resume.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Existing code that ignores connection events during
reset flow will never take effect since it locks the
same mutex taken by the reset flow.
In addition, in case of unsolicited disconnect events ignore
those as well since device is about to get reset.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Align to latest version of the auto generated wmi file
describing the interface with FW
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The 11ad spec requires 11ad devices to be able to receive 8KB
packets over the air. Currently this is only possible by
loading the driver with mtu_max=7912 but this also forces
a smaller block ACK window size which reduces performance
for stations which transmit normal sized packets (<2KB).
Fix this problem as follows:
1. Add a module parameter rx_large_buf that when set,
will allocate 8KB RX buffers regardless of mtu_max
setting.
2. When receiving block ACK request agree to any window
size not above our maximum, regardless of the mtu_max setting.
This means if the other side transmits small packets (2KB)
it can still set up block ACK with a large window size,
and get better performance.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The power save profile is set to default state in case of FW reset,
regardless of the state before the reset took place.
Fix this by saving the current power save profile and restore it
in case of FW reset.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Communication with FW must be done before wil->status
is initialized in order to properly handle cases where
communication with FW halts during reset sequence.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In 'ath10k_ce_alloc_pipe' the compile time sanity check to
ensure that there is sufficient buffers in CE4 for HTT Tx
MSDU descriptors, but this did not take into account of the
case with 'peer flow control' enabled, fix this.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fix fallout too.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When channel contexts are used, there's no global power level
(the power_level is always 0). Use the per-interface TX power
in mac80211_hwsim to have a proper setting for both cases.
This fixes the bgscan_simple and bgscan_learn test cases when
the number of channels advertised by hwsim is >1 by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should mitigate the system
hangs observed after the introduction of cpufreq for the A33.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
In common PLL designs, changes to the dividers take effect almost
immediately, while changes to the multipliers (implemented as
dividers in the feedback loop) take a few cycles to work into
the feedback loop for the PLL to stablize.
Sometimes when the PLL clock rate is changed, the decrease in the
divider is too much for the decrease in the multiplier to catch up.
The PLL clock rate will spike, and in some cases, might lock up
completely. This is especially the case if the divider changed is
the pre-divider, which affects the reference frequency.
This patch introduces a clk notifier callback that will gate and
then ungate a clk after a rate change, effectively resetting it,
so it continues to work, despite any possible lockups. Care must
be taken to reparent any consumers to other temporary clocks during
the rate change, and that this notifier callback must be the first
to be registered.
This is intended to fix occasional lockups with cpufreq on newer
Allwinner SoCs, such as the A33 and the H3. Previously it was
thought that reparenting the cpu clock away from the PLL while
it stabilized was enough, as this worked quite well on the A31.
On the A33, hangs have been observed after cpufreq was recently
introduced. With the H3, a more thorough test [1] showed that
reparenting alone isn't enough. The system still locks up unless
the dividers are limited to 1.
A hunch was if the PLL was stuck in some unknown state, perhaps
gating then ungating it would bring it back to normal. Tests
done by Icenowy Zheng using Ondrej's test firmware shows this
to be a valid solution.
[1] http://www.spinics.net/lists/arm-kernel/msg552501.html
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The ccu-sun9i-a80 driver uses the ccu_mult_ops struct, but unlike the other
users it doesen't select the corresponding Kconfig symbol under which the
struct is compiled in.
This results in the following link error with CONFIG_SUN9I_A80_CCU=y and
CONFIG_SUNXI_CCU_MULT=n:
drivers/built-in.o:(.data+0x2d638): undefined reference to 'ccu_mult_ops'
Fix this by explicitly selecting CONFIG_SUNXI_CCU_MULT like the other
users of the struct.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
With CONFIG_RESET_CONTROLLER=n we get the following link error in the
sunxi-ng clk driver:
drivers/built-in.o: In function `sunxi_ccu_probe':
mux-core.c:(.text+0x12fe68): undefined reference to 'reset_controller_register'
mux-core.c:(.text+0x12fe68): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'reset_controller_register'
Fix this by adding the appropriate select statement.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This adds a driver for the Nokia H4+ protocol, which is used
at least on the Nokia N9, N900 & N950.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, gvt, nouveau, udl and etnaviv fixes.
I was away the end of last week, so some of these would have been in
rc6, and it's Easter from tomorrow, so I decided I better dequeue what
I have now.
The nouveau changes, just add a hw enable for GP107 display (like a
pci id addition really), and fix a couple of regressions. i915 has
some more gvt fixes, along with a few run of the mill ones, the rcu
one seems like a few people have hit it.
Otherwise a small udl and small etnaviv fix"
* tag 'drm-fixes-for-v4.11-rc7' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
drm/udl: Fix unaligned memory access in udl_render_hline
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fixes from Thierry Reding:
"This contain a fix for the atomic update support recently added to
the Rockchip driver where the clock reference count would become
unbalanced and result in the clock feeding the PWM to always be
disabled.
Another fix to the Intel LPSS driver that adds an update bit quirk
required for a specific configuration"
* tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: rockchip: State of PWM clock should synchronize with PWM enabled state
pwm: lpss: Set enable-bit before waiting for update-bit to go low
pwm: lpss: Split Tangier configuration
|
|
Commit 10c7e20b2ff3 (ACPI / scan: fix enumeration (visited) flags for
bus rescans) attempted to fix a problem with ACPI-based enumerateion
of I2C/SPI devices, but it forgot to ensure that the visited flag
will be set for all of the other enumerated devices, so fix that.
Fixes: 10c7e20b2ff3 (ACPI / scan: fix enumeration (visited) flags for bus rescans)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194885
Reported-and-tested-by: Kevin Locke <kevin@kevinlocke.name>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
|
|
/sys/firmware/acpi/hotplug/force_remove was presumably added to support
auto offlining in the past. This is, however, inherently dangerous for
some hotplugable resources like memory. The memory offlining fails when
the memory is still in use and cannot be dropped or migrated. If we
ignore the failure we are basically allowing for subtle memory
corruption or a crash.
We have actually noticed the later while hitting BUG() during the memory
hotremove (remove_memory):
ret = walk_memory_range(PFN_DOWN(start), PFN_UP(start + size - 1), NULL,
check_memblock_offlined_cb);
if (ret)
BUG();
it took us quite non-trivial time realize that the customer had
force_remove enabled. Even if the BUG was removed here and we could
propagate the error up the call chain it wouldn't help at all because
then we would hit a crash or a memory corruption later and harder to
debug. So force_remove is unfixable for the memory hotremove. We haven't
checked other hotplugable resources to be prone to a similar problems.
Remove the force_remove functionality because it is not fixable currently.
Keep the sysfs file and report an error if somebody tries to enable it.
Encourage users to report about the missing functionality and work with
them with an alternative solution.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is a report that after commit 27622b061eb4 ("cpufreq: Convert
to hotplug state machine"), the normal CPU offline/online cycle
fails on some platforms.
According to the ftrace result, this problem was triggered on
platforms using acpi-cpufreq as the default cpufreq driver,
and due to the lack of some ACPI freq method (eg. _PCT),
cpufreq_online() failed and returned a negative value, so the CPU
hotplug state machine rolled back the CPU online process. Actually,
from the user's perspective, the failure of cpufreq_online() should
not prevent that CPU from being brought up, although cpufreq might
not work on that CPU.
BTW, during system startup cpufreq_online() is not invoked via CPU
online but by the cpufreq device creation process, so the APs can be
brought up even though cpufreq_online() fails in that stage.
This patch ignores the return value of cpufreq_online/offline() and
lets the cpufreq framework deal with the failure. cpufreq_online()
itself will do a proper rollback in that case and if _PCT is missing,
the ACPI cpufreq driver will print a warning if the corresponding
debug options have been enabled.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=194581
Fixes: 27622b061eb4 ("cpufreq: Convert to hotplug state machine")
Reported-and-tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
GP107 modesetting support (just recognising the chipset, no other changes until 4.12)
a couple of regression fixes, one of them a rather serious double-free issue that appeared in 4.10.
* 'linux-4.11' of git://github.com/skeggsb/linux:
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for v4.11-rc7
one rcu related fix, and a few GVT fixes.
* tag 'drm-intel-fixes-2017-04-12' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
drm/i915/perf: destroy stream on sample_flags mismatch
drm/i915: Align "unfenced" tiled access on gen2, early gen3
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
drm-misc-fixes for 2017-04-11
Core changes:
- None
Driver changes
- udl: Fix unaligned memory access on SPARC (Jonathan)
* tag 'drm-misc-fixes-2017-04-11' of git://anongit.freedesktop.org/git/drm-misc:
drm/udl: Fix unaligned memory access in udl_render_hline
|
|
into drm-fixes
Single etnaviv error path fix.
* 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux:
drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
|
|
The following warning triggers with a new unit test that stresses the
device-dax interface.
===============================
[ ERR: suspicious RCU usage. ]
4.11.0-rc4+ #1049 Tainted: G O
-------------------------------
./include/linux/rcupdate.h:521 Illegal context switch in RCU read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 0
2 locks held by fio/9070:
#0: (&mm->mmap_sem){++++++}, at: [<ffffffff8d0739d7>] __do_page_fault+0x167/0x4f0
#1: (rcu_read_lock){......}, at: [<ffffffffc03fbd02>] dax_dev_huge_fault+0x32/0x620 [dax]
Call Trace:
dump_stack+0x86/0xc3
lockdep_rcu_suspicious+0xd7/0x110
___might_sleep+0xac/0x250
__might_sleep+0x4a/0x80
__alloc_pages_nodemask+0x23a/0x360
alloc_pages_current+0xa1/0x1f0
pte_alloc_one+0x17/0x80
__pte_alloc+0x1e/0x120
__get_locked_pte+0x1bf/0x1d0
insert_pfn.isra.70+0x3a/0x100
? lookup_memtype+0xa6/0xd0
vm_insert_mixed+0x64/0x90
dax_dev_huge_fault+0x520/0x620 [dax]
? dax_dev_huge_fault+0x32/0x620 [dax]
dax_dev_fault+0x10/0x20 [dax]
__do_fault+0x1e/0x140
__handle_mm_fault+0x9af/0x10d0
handle_mm_fault+0x16d/0x370
? handle_mm_fault+0x47/0x370
__do_page_fault+0x28c/0x4f0
trace_do_page_fault+0x58/0x2a0
do_async_page_fault+0x1a/0xa0
async_page_fault+0x28/0x30
Inserting a page table entry may trigger an allocation while we are
holding a read lock to keep the device instance alive for the duration
of the fault. Use srcu for this keep-alive protection.
Fixes: dee410792419 ("/dev/dax, core: file operations and dax-mmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The latest USB keyboards shipped on several ASUS laptop models
(including ROG laptop models such as GL702VMK) have the keyboards
backlight controlled by the keyboard firmware.
The firmware implements at least 3 different commands:
- Init command (to use when the system starts)
- Configuration command (to get keyboard status/information)
- Backlight level control (to change the level of the keyboard light)
With this patch we create the usual 'asus::kbd_backlight' led class
entry to control the keyboard backlight.
[jkosina@suse.cz: remove pointless cancel_work_sync() call while
handling an error in asus_kbd_register_leds(), as spotted by
Benjamin]
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
For bluetooth protocol driver only supporting serdev it makes
sense to follow common practice and built them into their own
module.
Such modules need access to hci_uart_register_device and
hci_uart_tx_wakeup for using the common protocol helpers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The device driver may need to communicate with the UART
device while the Bluetooth device is closed (e.g. due
to interrupts).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds library functions for serdev based BT drivers. This is largely
copied from hci_ldisc.c and modified to use serdev calls. There's a little
bit of duplication, but I avoided intermixing this as the ldisc code should
eventually go away.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
[Fix style issues reported by Pavel]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
