| Age | Commit message (Collapse) | Author |
|---|
|
The AM65x HyperBus controller is only present on Texas Instruments AM65x
SoCs. Hence add a dependency on ARCH_K3, to prevent asking the user
about this driver when configuring a kernel without support for the
Texas Instruments Inc. K3 multicore SoC architecture.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/9fd6b975adba710158f28aa603cf87a6d189a418.1646655894.git.geert+renesas@glider.be
|
|
partid and partname debugfs files were used just by SPI NOR, but they were
replaced by sysfs entries. Since these debugfs files are no longer used in
mtd, remove dead code. The directory is kept as it is used by nandsim,
mtdswap and docg3.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220225144656.634682-1-tudor.ambarus@microchip.com
|
|
While calculating speed during mtd_speedtest, the time interval
(i.e., start - finish) is rounded off to the nearest milliseconds by
ignoring the fractional part. This leads to miscalculation of speed.
The miscalculation is more visible while running speed test on small
partition sizes(i.e., when partition size is equal to eraseblock size or
twice the eraseblock size) at higher spi frequencies.
For e.g., while calculating eraseblock read speed for a mtd partition with
size equal to the eraseblock size(i.e., 64KiB) the eraseblock read time
interval comes out to be 966490 nanosecond. This is then converted to
millisecond(i.e., 0.966 msec.). The integer part (i.e., 0 msec) of the
value is considered and the fractional part (i.e., 0.966) is ignored,for
calculating the eraseblock read speed. So the reported eraseblock read
speed is 0 KiB/s, which is incorrect.
There are two approaches to fix this issue.
First approach will be to keep the time interval in millisecond. and round
up the integer value, with this approach the 0.966msec time interval in the
above example will be rounded up to 1msec and this value is used for
calculating the speed. Downside of this approach is that the reported speed
is still not accurate.
Second approach will be to convert the time interval to microseconds
instead of milliseconds, with this approach the 966490 nanosecond time
interval in the above example will be converted t0 966.490usec and this
value is used for calculating the speed. As compared to the current
implementation and the suggested First approach, this approach will report
a more accurate speed. Downside of this approach is that, in future if the
mtd size is too large then the u64 variable, that holds the number of
bytes, might overflow.
In this patch we have gone with the second approach as this reports a more
accurate speed. With this approach the eraseblock read speed in the above
example comes out to be 132505 KiB/s when the spi clock is configured at
150Mhz.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220208103905.13354-1-amit.kumar-mahapatra@xilinx.com
|
|
The reference counting issue happens in several error handling paths
on a refcounted object "nc->dmac". In these paths, the function simply
returns the error code, forgetting to balance the reference count of
"nc->dmac", increased earlier by dma_request_channel(), which may
cause refcount leaks.
Fix it by decrementing the refcount of specific object in those error
paths.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Co-developed-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn
|
|
Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.
Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220303123431.3170-1-hanyihao@vivo.com
|
|
Several WMI queries leverage hp_wmi_read_int function to read their
data. hp_wmi_read_int function was corrected in a previous patch.
Now, this function invokes hp_wmi_perform_query with input parameter
of size zero and the output buffer of size 4.
WMI commands calling hp_wmi_perform_query with input buffer size value
of zero are listed below.
HPWMI_DISPLAY_QUERY
HPWMI_HDDTEMP_QUERY
HPWMI_ALS_QUERY
HPWMI_HARDWARE_QUERY
HPWMI_WIRELESS_QUERY
HPWMI_BIOS_QUERY
HPWMI_FEATURE_QUERY
HPWMI_HOTKEY_QUERY
HPWMI_FEATURE2_QUERY
HPWMI_WIRELESS2_QUERY
HPWMI_POSTCODEERROR_QUERY
HPWMI_THERMAL_PROFILE_QUERY
HPWMI_FAN_SPEED_MAX_GET_QUERY
Invoking those WMI commands with an input buffer size greater
than zero will cause error 0x05 to be returned.
All WMI commands executed by the driver were reviewed and changes
were made to ensure the expected input and output buffer size match
the WMI specification.
Changes were validated on a HP ZBook Workstation notebook,
HP EliteBook x360, and HP EliteBook 850 G8. Additional
validation was included in the test process to ensure no other
commands were incorrectly handled.
Signed-off-by: Jorge Lopez <jorge.lopez2@hp.com>
Link: https://lore.kernel.org/r/20220310210853.28367-4-jorge.lopez2@hp.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The purpose of this patch is to introduce a fix and removal of the
current hack when determining tablet mode status.
Determining the tablet mode status requires reading Byte 0 bit 2 as
reported by HPWMI_HARDWARE_QUERY. The investigation identified the
failure was rooted in two areas: HPWMI_HARDWARE_QUERY failure (0x05)
and reading Byte 0, bit 2 only to determine the table mode status.
HPWMI_HARDWARE_QUERY WMI failure also rendered the dock state value
invalid.
The latest changes use SMBIOS Type 3 (chassis type) and WMI Command
0x40 (device_mode_status) information to determine if the device is
in tablet mode or not.
hp_wmi_hw_state function was split into two functions;
hp_wmi_get_dock_state and hp_wmi_get_tablet_mode. The new functions
separate how dock_state and tablet_mode is handled in a cleaner
manner.
All changes were validated on a HP ZBook Workstation notebook,
HP EliteBook x360, and HP EliteBook 850 G8.
Signed-off-by: Jorge Lopez <jorge.lopez2@hp.com>
Link: https://lore.kernel.org/r/20220310210853.28367-3-jorge.lopez2@hp.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The purpose of this patch is to introduce a fix to hp_wmi_read_int()
and eliminate failure error (0x05). Several WMI queries leverage
hp_wmi_read_int() to read their data and were failing with error 0x05.
HPWMI_DISPLAY_QUERY
HPWMI_HDDTEMP_QUERY
HPWMI_ALS_QUERY
HPWMI_HARDWARE_QUERY
HPWMI_WIRELESS_QUERY
HPWMI_POSTCODEERROR_QUERY
The failure occurs because hp_wmi_read_int() calls
hp_wmi_perform_query() with input parameter of size greater than zero.
Invoking those WMI commands with an input buffer size greater than
zero causes the command to be rejected and error 0x05 be returned.
All changes were validated on a HP ZBook Workstation notebook,
HP EliteBook x360, and HP EliteBook 850 G8.
Signed-off-by: Jorge Lopez <jorge.lopez2@hp.com>
Link: https://lore.kernel.org/r/20220310210853.28367-2-jorge.lopez2@hp.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Fix "no previous prototype" W=1 warning by making the function
vchiq_platform_get_arm_state() static.
While at it, realign the function declaration in one line and reposition
the asterisk symbol to fulfill the 'foo *bar' syntax.
Signed-off-by: Gaston Gonzalez <gascoar@gmail.com>
Link: https://lore.kernel.org/r/216ad30d674b80e0051ecc233ac26ddb1d3e0e75.1646255044.git.gascoar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the cpuintc and fixedregulator dtc warnings:
Warning (unit_address_vs_reg): /cpuintc@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /fixedregulator@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /fixedregulator@1: node has a unit name, but no reg property
Warning (unique_unit_address): /cpuintc@0: duplicate unit-address (also used in node /fixedregulator@0)
Remove the unnecessary status = "okay" property from the xhci node.
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20220312091832.6269-1-arinc.unal@arinc9.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the GB-PC2 devicetree. Refer to the schematics of the device for more
information.
GB-PC2 devicetree fixes:
- Include mt7621.dtsi instead of gbpc1.dts. Add the missing definitions.
- Remove gpio-leds node as the system LED is not wired to anywhere on
the board and the power LED is directly wired to GND.
- Remove uart3 pin group from gpio-pinmux node as it's not used as GPIO.
- Use reg 7 for the external phy to be on par with
Documentation/devicetree/bindings/net/dsa/mt7530.txt.
- Use the status value "okay".
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20220311090320.3068-2-arinc.unal@arinc9.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix LED and pinctrl definitions on the GB-PC1 devicetree. Refer to the
schematics of the device for more information.
LED fixes:
- Change GPIO6 LED label from system to power as GPIO6 is connected to
PLED.
- Add default-on default-trigger to power LED.
- Change GPIO8 LED label from status to system as GPIO8 is connected to
SYS_LED.
- Add disk-activity default-trigger to system LED.
- Switch to the color:function naming scheme.
- Remove lan1 and lan2 LEDs as they don't exist.
Pinctrl fixes:
- Claim state_default node under pinctrl node.
- Change pinctrl0 node name to state-default.
- Change gpio node name to gpio-pinmux to respect
Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml.
- Sort pin groups alphabetically.
Misc fixes:
- Fix formatting.
- Use the status value "okay".
- Define hexadecimal addresses in lower case.
- Make hexadecimal addresses for memory easier to read.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC1_V1.0_Schematic.pdf
Tested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20220311090320.3068-1-arinc.unal@arinc9.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220314115354.144023-8-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: 2121aa3e2312 ("mips: cdmm: Add mti,mips-cdmm dtb node support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
This patch integrates the dpaa2-eth driver with the generic PHY
infrastructure in order to search, find and reconfigure the SerDes lanes
in case of a protocol change.
On the .mac_config() callback, the phy_set_mode_ext() API is called so
that the Lynx 28G SerDes PHY driver can change the lane's configuration.
In the same phylink callback the MC firmware is called so that it
reconfigures the MAC side to run using the new protocol.
The consumer drivers - dpaa2-eth and dpaa2-switch - are updated to call
the dpaa2_mac_start/stop functions newly added which will
power_on/power_off the associated SerDes lane.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic to setup the supported interfaces will get annotated based on
what the configuration of the SerDes PLLs supports. Move the current
setup into a separate function just to try to keep it clean.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Retrieve the API version running on the firmware and based on it detect
which features are available for usage.
The first one to be listed is the capability to change the MAC protocol
at runtime.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MC firmware gained recently a new command which can reconfigure the
running protocol on the underlying MAC. Add this new command which will
be used in the next patches in order to do a major reconfig on the
interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dpmac_get_api_version command will be used in the next patches to
determine if the current firmware is capable or not to change the
Ethernet protocol running on the MAC.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new generic PHY driver to support the Lynx 28G SerDes
block found on some of the Layerscape SoCs such as LX2160A.
At the moment, only the following Ethernet protocols are supported:
SGMII/1000Base-X and 10GBaseR.
SerDes lanes which are not running an Ethernet protocol or a currently
supported Ethenet protocol will be left as it was configured through the
RCW (Reset Configuration Word) at boot time.
At probe time, the platform driver will read the current
configuration of both PLLs found on a SerDes block and will determine
what protocols are supported using that PLL.
For example, if a PLL is configured to generate a clock net (frate) of
5GHz the only protocols sustained by that PLL are SGMII/1000Base-X
(using a quarter of the full clock rate) and QSGMII using the full clock
net frequency on the lane.
On the .set_mode() callback, the PHY driver will first check if the
requested operating mode (protocol) is even supported by the current PLL
configuration and will error out if not.
Then, the lane is reconfigured to run on the requested protocol.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the controller is transitioning to L1 in rcar_pcie_config_access(),
any read/write access to PCIECDR triggers asynchronous external abort. This
is because the transition to L1 link state must be manually finished by the
driver. The PCIe IP can transition back from L1 state to L0 on its own.
The current asynchronous external abort hook implementation restarts
the instruction which finally triggered the fault, which can be a
different instruction than the read/write instruction which started
the faulting access. Usually the instruction which finally triggers
the fault is one which has some data dependency on the result of the
read/write. In case of read, the read value after fixup is undefined,
while a read value of faulting read should be PCI_ERROR_RESPONSE.
It is possible to enforce the fault using 'isb' instruction placed
right after the read/write instruction which started the faulting
access. Add custom register accessors which perform the read/write
followed immediately by 'isb'.
This way, the fault always happens on the 'isb' and in case of read,
which is located one instruction before the 'isb', it is now possible
to fix up the return value of the read in the asynchronous external
abort hook and make that read return PCI_ERROR_RESPONSE.
Link: https://lore.kernel.org/r/20220312212349.781799-2-marek.vasut@gmail.com
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
|
|
In case the controller is transitioning to L1 in rcar_pcie_config_access(),
any read/write access to PCIECDR triggers asynchronous external abort. This
is because the transition to L1 link state must be manually finished by the
driver. The PCIe IP can transition back from L1 state to L0 on its own.
Avoid triggering the abort in rcar_pcie_config_access() by checking whether
the controller is in the transition state, and if so, finish the transition
right away. This prevents a lot of unnecessary exceptions, although not all
of them.
Link: https://lore.kernel.org/r/20220312212349.781799-1-marek.vasut@gmail.com
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
|
|
Add spi_device_id tables to avoid logs like "SPI driver ksz9477-switch
has no spi_device_id".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add net device refcount tracker to macvlan.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the reference operation to lowerdev of macvlan to avoid
the potential UAF problem under the following known scenario:
Someone module puts the NETDEV_UNREGISTER event handler to a
work, and lowerdev is accessed in the work handler. But when
the work is excuted, lowerdev has been destroyed because upper
macvlan did not get reference to lowerdev correctly.
That likes as the scenario occurred by
commit 563bcbae3ba2 ("net: vlan: fix a UAF in vlan_dev_real_dev()").
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocating memory with kmalloc and GPF_DMA32 is not allowed, the
allocator will ignore the attribute.
Instead, use dma_alloc_coherent() API as we allocate a small amount of
memory to transfer firmware fragment to the ISH.
On Arcada chromebook, after the patch the warning:
"Unexpected gfp: 0x4 (GFP_DMA32). Fixing up to gfp: 0xcc0 (GFP_KERNEL). Fix your code!"
is gone. The ISH firmware is loaded properly and we can interact with
the ISH:
> ectool --name cros_ish version
...
Build info: arcada_ish_v2.0.3661+3c1a1c1ae0 2022-02-08 05:37:47 @localhost
Tool version: v2.0.12300-900b03ec7f 2022-02-08 10:01:48 @localhost
Fixes: commit 91b228107da3 ("HID: intel-ish-hid: ISH firmware loader client driver")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
Link: https://lore.kernel.org/all/20220313105142.704579-1-maz@kernel.org
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clocksource/events updates from Daniel Lezcano:
- Fix return error code check for the timer-of layer when getting
the base address (Guillaume Ranquet)
- Remove MMIO dependency, add notrace annotation for sched_clock
and increase the timer resolution for the Microchip
PIT64b (Claudiu Beznea)
- Convert DT bindings to yaml for the Tegra timer (David Heidelberg)
- Fix compilation error on architecture other than ARM for the
i.MX TPM (Nathan Chancellor)
- Add support for the event stream scaling for 1GHz counter on
the arch ARM timer (Marc Zyngier)
- Support a higher number of interrupts by the Exynos MCT timer
driver (Alim Akhtar)
- Detect and prevent memory corruption when the specified number
of interrupts in the DTS is greater than the array size in the
code for the Exynos MCT timer (Krzysztof Kozlowski)
- Fix regression from a previous errata fix on the TI DM
timer (Drew Fustini)
- Several fixes and code improvements for the i.MX TPM
driver (Peng Fan)
Link: https://lore.kernel.org/all/a8cd9be9-7d70-80df-2b74-1a8226a215e1@linaro.org
|
|
In order to better organize the platform/Kconfig, place
exynos-gsc-specific config stuff on a separate Kconfig file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In order to better organize the platform/Kconfig, place
coda-specific config stuff on a separate Kconfig file.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In order to better organize the platform/Kconfig, place
amphion-specific config stuff on a separate Kconfig file.
Reviewed-by: Shijie Qin <shijie.qin@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In order to better organize the platform/Kconfig, place
allegro-dvt-specific config stuff on a separate Kconfig file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In order to cleanup the main platform media directory, move Renesas
driver to its own directory.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In order to cleanup the main platform media directory, move Via
driver to its own directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In order to cleanup the main platform media directory, move Intel
driver to its own directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In order to cleanup the main platform media directory, move NXP
drivers to their own directory.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In order to cleanup the main platform media directory, move Aspeed
driver to its own directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Right now, platform dependencies are organized by the type of
the platform driver. Yet, things tend to become very messy with
time. The better seems to organize the drivers per manufacturer,
as other Kernel subsystems are doing.
As a preparation for such purpose, get rid of menuconfigs,
moving the per-menu dependencies to be at the driver-specifig
config entires.
This shoud give flexibility to reorganize the platform drivers
per manufacturer and re-sort them.
This patch removes all "if..endif" options from the platform
Kconfig, converting them into depends on.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
There are lots of inconsistencies here: some directories are
included as-is, and others included using one (or more) symbols
that are inside it. Also, its entries are not sorted.
That makes it harder to maintain.
Reorganize it by placing everything on alphabetic order and
providing some hints about how patches for such file is expected.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Alphabetically sort entries at the Makefiles per group,
in ASCII order, e. g., using the output of:
$ LC_ALL=C sort Makefile |grep obj-y
...
$ LC_ALL=C sort Makefile |grep obj.*CONFIG
...
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
A missing bounds check in vm_access() can lead to an out-of-bounds read
or write in the adjacent memory area, since the len attribute is not
validated before the memcpy later in the function, potentially hitting:
[ 183.637831] BUG: unable to handle page fault for address: ffffc90000c86000
[ 183.637934] #PF: supervisor read access in kernel mode
[ 183.637997] #PF: error_code(0x0000) - not-present page
[ 183.638059] PGD 100000067 P4D 100000067 PUD 100258067 PMD 106341067 PTE 0
[ 183.638144] Oops: 0000 [#2] PREEMPT SMP NOPTI
[ 183.638201] CPU: 3 PID: 1790 Comm: poc Tainted: G D 5.17.0-rc6-ci-drm-11296+ #1
[ 183.638298] Hardware name: Intel Corporation CoffeeLake Client Platform/CoffeeLake H DDR4 RVP, BIOS CNLSFWR1.R00.X208.B00.1905301319 05/30/2019
[ 183.638430] RIP: 0010:memcpy_erms+0x6/0x10
[ 183.640213] RSP: 0018:ffffc90001763d48 EFLAGS: 00010246
[ 183.641117] RAX: ffff888109c14000 RBX: ffff888111bece40 RCX: 0000000000000ffc
[ 183.642029] RDX: 0000000000001000 RSI: ffffc90000c86000 RDI: ffff888109c14004
[ 183.642946] RBP: 0000000000000ffc R08: 800000000000016b R09: 0000000000000000
[ 183.643848] R10: ffffc90000c85000 R11: 0000000000000048 R12: 0000000000001000
[ 183.644742] R13: ffff888111bed190 R14: ffff888109c14000 R15: 0000000000001000
[ 183.645653] FS: 00007fe5ef807540(0000) GS:ffff88845b380000(0000) knlGS:0000000000000000
[ 183.646570] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 183.647481] CR2: ffffc90000c86000 CR3: 000000010ff02006 CR4: 00000000003706e0
[ 183.648384] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 183.649271] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 183.650142] Call Trace:
[ 183.650988] <TASK>
[ 183.651793] vm_access+0x1f0/0x2a0 [i915]
[ 183.652726] __access_remote_vm+0x224/0x380
[ 183.653561] mem_rw.isra.0+0xf9/0x190
[ 183.654402] vfs_read+0x9d/0x1b0
[ 183.655238] ksys_read+0x63/0xe0
[ 183.656065] do_syscall_64+0x38/0xc0
[ 183.656882] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 183.657663] RIP: 0033:0x7fe5ef725142
[ 183.659351] RSP: 002b:00007ffe1e81c7e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[ 183.660227] RAX: ffffffffffffffda RBX: 0000557055dfb780 RCX: 00007fe5ef725142
[ 183.661104] RDX: 0000000000001000 RSI: 00007ffe1e81d880 RDI: 0000000000000005
[ 183.661972] RBP: 00007ffe1e81e890 R08: 0000000000000030 R09: 0000000000000046
[ 183.662832] R10: 0000557055dfc2e0 R11: 0000000000000246 R12: 0000557055dfb1c0
[ 183.663691] R13: 00007ffe1e81e980 R14: 0000000000000000 R15: 0000000000000000
Changes since v1:
- Updated if condition with range_overflows_t [Chris Wilson]
Fixes: 9f909e215fea ("drm/i915: Implement vm_ops->access for gdb access into mmaps")
Signed-off-by: Mastan Katragadda <mastanx.katragadda@intel.com>
Suggested-by: Adam Zabrocki <adamza@microsoft.com>
Reported-by: Jackson Cody <cody.jackson@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
[mauld: tidy up the commit message and add Cc: stable]
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303060428.1668844-1-mastanx.katragadda@intel.com
(cherry picked from commit 661412e301e2ca86799aa4f400d1cf0bd38c57c6)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Instead of using sprintf, use snprintf with buffer size limited to
PAGE_SIZE just like what we have for the rest of the file.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Don't fold line that can fit into 80 char limit. No functional change
in this patch.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This fixes following kernel-doc warning:-
drivers/nvme/target/rdma.c:1722: warning: expecting prototype for nvme_rdma_device_removal(). Prototype was for nvmet_rdma_device_removal() instead
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This fixes following kernel-doc warning:-
drivers/nvme/target/fc.c:1619: warning: expecting prototype for nvme_fc_unregister_targetport(). Prototype was for nvmet_fc_unregister_targetport() instead
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This fixes following kernel-doc warning :-
drivers/nvme/target/fc.c:1365: warning: expecting prototype for nvme_fc_register_targetport(). Prototype was for nvmet_fc_register_targetport() instead
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Put NVMe/TCP sockets in their own class to avoid some lockdep warnings.
Sockets created by nvme-tcp are not exposed to user-space, and will not
trigger certain code paths that the general socket API exposes.
Lockdep complains about a circular dependency between the socket and
filesystem locks, because setsockopt can trigger a page fault with a
socket lock held, but nvme-tcp sends requests on the socket while file
system locks are held.
======================================================
WARNING: possible circular locking dependency detected
5.15.0-rc3 #1 Not tainted
------------------------------------------------------
fio/1496 is trying to acquire lock:
(sk_lock-AF_INET){+.+.}-{0:0}, at: tcp_sendpage+0x23/0x80
but task is already holding lock:
(&xfs_dir_ilock_class/5){+.+.}-{3:3}, at: xfs_ilock+0xcf/0x290 [xfs]
which lock already depends on the new lock.
other info that might help us debug this:
chain exists of:
sk_lock-AF_INET --> sb_internal --> &xfs_dir_ilock_class/5
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&xfs_dir_ilock_class/5);
lock(sb_internal);
lock(&xfs_dir_ilock_class/5);
lock(sk_lock-AF_INET);
*** DEADLOCK ***
6 locks held by fio/1496:
#0: (sb_writers#13){.+.+}-{0:0}, at: path_openat+0x9fc/0xa20
#1: (&inode->i_sb->s_type->i_mutex_dir_key){++++}-{3:3}, at: path_openat+0x296/0xa20
#2: (sb_internal){.+.+}-{0:0}, at: xfs_trans_alloc_icreate+0x41/0xd0 [xfs]
#3: (&xfs_dir_ilock_class/5){+.+.}-{3:3}, at: xfs_ilock+0xcf/0x290 [xfs]
#4: (hctx->srcu){....}-{0:0}, at: hctx_lock+0x51/0xd0
#5: (&queue->send_mutex){+.+.}-{3:3}, at: nvme_tcp_queue_rq+0x33e/0x380 [nvme_tcp]
This annotation lets lockdep analyze nvme-tcp controlled sockets
independently of what the user-space sockets API does.
Link: https://lore.kernel.org/linux-nvme/CAHj4cs9MDYLJ+q+2_GXUK9HxFizv2pxUryUR0toX974M040z7g@mail.gmail.com/
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The call to nvme_tcp_alloc_queue() fits perfectly in one line without
exceeding 80 char limit for the line.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
