| Age | Commit message (Collapse) | Author |
|---|
|
Use the ARRAY_SIZE macro on various arrays to determine
size of the arrays. Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the case of the Tx rings we need to only clear the Tx buffer_info when
we are resetting the rings. Ideally we do this when we configure the ring
to bring it back up instead of when we are taking it down in order to avoid
dirtying pages we don't need to.
In addition we don't need to clear the Tx descriptor ring since we will
fully repopulate it when we begin transmitting frames and next_to_watch can
be cleared to prevent the ring from being cleaned beyond that point instead
of needing to touch anything in the Tx descriptor ring.
Finally with these changes we can avoid having to reset the skb member of
the Tx buffer_info structure in the cleanup path since the skb will always
be associated with the first buffer which has next_to_watch set.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
|
|
'spi/topic/sh-msiof', 'spi/topic/sirf' and 'spi/topic/sun6i' into spi-next
|
|
'spi/topic/jcore', 'spi/topic/meson' and 'spi/topic/orion' into spi-next
|
|
'spi/topic/bcm53xx', 'spi/topic/davinci' and 'spi/topic/dw' into spi-next
|
|
spi-linus
|
|
|
|
'regulator/topic/sc2731' into regulator-next
|
|
|
|
|
|
3d67fe950707 (regulator: core: Refactor regulator_list_voltage()) missed
one user of regulator_list_voltage(), update for that.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-core
|
|
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add description for 'data' parameter and drop unused 'irq' memeber.
Here is the warnings:
drivers/i2c/busses/i2c-meson.c:103: warning: No description found for
parameter 'data'
drivers/i2c/busses/i2c-meson.c:103: warning: Excess struct member 'irq'
description in 'meson_i2c'
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Pull networking fixes from David Miller:
1) The per-network-namespace loopback device, and thus its namespace,
can have its teardown deferred for a long time if a kernel created
TCP socket closes and the namespace is exiting meanwhile. The kernel
keeps trying to finish the close sequence until it times out (which
takes quite some time).
Fix this by forcing the socket closed in this situation, from Dan
Streetman.
2) Fix regression where we're trying to invoke the update_pmtu method
on route types (in this case metadata tunnel routes) that don't
implement the dst_ops method. Fix from Nicolas Dichtel.
3) Fix long standing memory corruption issues in r8169 driver by
performing the chip statistics DMA programming more correctly. From
Francois Romieu.
4) Handle local broadcast sends over VRF routes properly, from David
Ahern.
5) Don't refire the DCCP CCID2 timer endlessly, otherwise the socket
can never be released. From Alexey Kodanev.
6) Set poll flags properly in VSOCK protocol layer, from Stefan
Hajnoczi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
VSOCK: set POLLOUT | POLLWRNORM for TCP_CLOSING
dccp: don't restart ccid2_hc_tx_rto_expire() if sk in closed state
net: vrf: Add support for sends to local broadcast address
r8169: fix memory corruption on retrieval of hardware statistics.
net: don't call update_pmtu unconditionally
net: tcp: close sock if net namespace is exiting
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A fairly urgent nouveau regression fix for broken irqs across
suspend/resume came in. This was broken before but a patch in 4.15 has
made it much more obviously broken and now s/r fails a lot more often.
The fix removes freeing the irq across s/r which never should have
been done anyways.
Also two vc4 fixes for a NULL deference and some misrendering /
flickering on screen"
* tag 'drm-fixes-for-v4.15-rc10-2' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: Move irq setup/teardown to pci ctor/dtor
drm/vc4: Fix NULL pointer dereference in vc4_save_hang_state()
drm/vc4: Flush the caches before the bin jobs, as well.
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Pull "one ti-sysc driver fix for v4.16 merge window" from Tony Lindgren:
One minor fix for ti-sysc smartreflex sysc mask that prevents idling
the smartreflex interconnect target module for device tree based
probing.
* tag 'omap-for-v4.16/ti-sysc-fix-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix smartreflex sysc mask
|
|
https://github.com/Xilinx/linux-xlnx into next/drivers
Pull "arm: Xilinx ZynqMP SoC fixes for v4.16" from Michal Simek:
- Fix Kconfig dependency
- Fix vcu clkoutdiv calculation
* tag 'zynqmp-soc-fixes-for-4.16' of https://github.com/Xilinx/linux-xlnx:
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
|
|
Fallback to backdoor register access to collect dumps if firmware
is crashed. Fixes TID, SGE Queue Context, and MPS TCAM dump collection.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only contact firmware if it's alive _AND_ if use_bd (use backdoor
access) is not set when issuing FW_LDST_CMD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware reports error, reset FW_OK flag.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just like PF, if the int_gl_idx of VF does not be set, the default
interrupt coalesce index of VF is 0. But it should be GL1 for TX
queues and GL0 for RX queues.
This patch adds the int_gl_idx setup for VF.
Fixes: 200ecda42598 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds ethtool_ops.get/set_coalesce support to VF.
Since PF and VF share the same get/set_coalesce interface,
we only need to set hns3_get/set_coalesce to the ethtool_ops
when supporting get/set_coalesce for VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2018-01-26
this is a pull request for net-next/master consisting of 3 patches.
The first two patches target the CAN documentation. The first is by me
and fixes pointer to location of fsl,mpc5200-mscan node in the mpc5200
documentation. The second patch is by Robert Schwebel and it converts
the plain ASCII documentation to restructured text.
The third patch is by Fabrizio Castro add the r8a774[35] support to the
rcar_can dt-bindings documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change _regulator_list_voltage() argument from regulator to
regulator_dev in order to provide better separation of core layers.
Allow calling _regulator_list_voltage() from functions, with
regulator_dev argument. This refactoring is needed in order to
implement setting voltage of coupled regulators.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As of_find_regulator_by_node() is an of function it should be moved from
core.c to of_regulator.c. It provides better separation of device tree
functions from the core and allows other of_functions in of_regulator.c
to resolve device_node to regulator_dev. This will be useful for
implementation of parsing coupled regulators properties.
Declare of_find_regulator_by_node() function in internal.h as well as
regulator_class and dev_to_rdev(), as they are needed by
of_find_regulator_by_node().
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Based on commit ec718254cbfe
("ixgbe: Improve performance and reduce size of ixgbe_tx_map")
This change is meant to both improve the performance and reduce the size of
ixgbevf_tx_map().
Expand the work done in the main loop by pushing first into tx_buffer.
This allows us to pull in the dma_mapping_error check, the tx_buffer value
assignment, and the initial DMA value assignment to the Tx descriptor.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit d2bead576e67
("igb: Clear Rx buffer_info in configure instead of clean")
This change makes it so that instead of going through the entire ring on Rx
cleanup we only go through the region that was designated to be cleaned up
and stop when we reach the region where new allocations should start.
In addition we can avoid having to perform a memset on the Rx buffer_info
structures until we are about to start using the ring again.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We already had placehloders for failed page and buffer allocations.
Added alloc_rx_page and made sure the stats are properly updated and
exposed in ethtool.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit bd4171a5d4c2
("igb: update code to better handle incrementing page count")
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit 5be5955425c2
("igb: update driver to make use of DMA_ATTR_SKIP_CPU_SYNC")
and
commit 7bd175928280 ("igb: Add support for DMA_ATTR_WEAK_ORDERING")
Convert the calls to dma_map/unmap_page() to the attributes version
and add DMA_ATTR_SKIP_CPU_SYNC/WEAK_ORDERING which should help
improve performance on some platforms.
Move sync_for_cpu call before we perform a prefetch to avoid
invalidating the first 128 bytes of the packet on architectures where
that call may invalidate the cache.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on:
commit 7ec0116c9131 ("igb: Use length to determine if descriptor is done")
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
In addition we only reset the Rx descriptor length for descriptor zero when
resetting a ring instead of having to do a memset with 0 over the entire
ring. By doing this we can save some time on initialization.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit 64f2525ca4e7 ("igb: Only DMA sync frame length")
On some architectures synching a buffer for DMA may be expensive.
Instead of the entire 2K receive buffer only synchronize the length of
the frame, which will typically be the MTU or smaller.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Introduce ixgbevf_can_reuse_page() similar to the change in ixgbe from
commit af43da0dba0b
("ixgbe: Add function for checking to see if we can reuse page")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
get_user_pages() must be called with mmap_sem held, currently
it is not. In fact it is called under the user db_table->mutex.
To fix this we can convert gup to use the fast alternative,
and safely avoid taking mmap_sem, if possible. Furthermore
this is safe wrt to the mutex as other callers that take the
lock (unmap and alloc_db) are not called under mmap_sem
(hence possible deadlock).
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Fixes: 1280c0f8aafc ("sfc: support second + quarter ns time format for receive datapath")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After upgrading an old laptop to 4.15-rc9, I found that the eth0 and
wlan0 interfaces had disappeared. It turns out that the b43 and b44
drivers require SSB_PCIHOST_POSSIBLE which depends on
PCI_DRIVERS_LEGACY, a config option that only exists on Mips.
Fixes: 58eae1416b80 ("ssb: Disable PCI host for PCI_DRIVERS_GENERIC")
Cc: stable@vger.org
Signed-off-by: Sven Joachim <svenjoac@gmx.de>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Local struct chip_data has two members that are not used:
- cs. Looks like was never used
- enable_dma. Became unused by the commit f89a6d8f43eb ("spi: dw-mid: move
to use core SPI DMA mappings").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In this patch, consumers are allowed to set suspend voltage, and this
actually just set the "uV" in constraint::regulator_state, when the
regulator_suspend_late() was called by PM core through callback when
the system is entering into suspend, the regulator device would act
suspend activity then.
And it assumes that if any consumer set suspend voltage, the regulator
device should be enabled in the suspend state. And if the suspend
voltage of a regulator device for all consumers was set zero, the
regulator device would be off in the suspend state.
This patch also provides a new function hook to regulator devices for
resuming from suspend states.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Regualtor suspend/resume functions should only be called by PM suspend
core via registering dev_pm_ops, and regulator devices should implement
the callback functions. Thus, any regulator consumer shouldn't call
the regulator suspend/resume functions directly.
In order to avoid compile errors, two empty functions with the same name
still be left for the time being.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The items "disabled" and "enabled" are a little redundant, since only one
of them would be set to record if the regulator device should keep on
or be switched to off in suspend states.
So in this patch, the "disabled" was removed, only leave the "enabled":
- enabled == 1 for regulator-on-in-suspend
- enabled == 0 for regulator-off-in-suspend
- enabled == -1 means do nothing when entering suspend mode.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some regulator consumers would like to make the regulator device
keeping a voltage range output when the system entering into
suspend states.
Making regulator voltage be an array can allow consumers to set voltage
for normal state as well as for suspend states through the same code.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The initialization of cfg_cmd is redundant as the value is never read
and it is being re-assigned to cfg_cmd = pwrcfgcmd[ary_idx] inside a
loop, hence it can be removed.
Cleans up clang warning:
drivers/staging/rtlwifi/core.c:1819:22: warning: Value stored to
'cfg_cmd' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The initialization of PwrCfgCmd is redundant as the value is never read
and it is being re-assigned to PwrSeqCmd[AryIdx] inside a loop, hence
it can be removed. Also, the initialization of ie_ptr is redundant as
the value is never read and it is being re-assigned in either path of
an if statement, hence it can be removed too.
Cleans up clang warnings:
drivers/staging/rtl8723bs/hal/HalPwrSeqCmd.c:53:15: warning: Value
stored to 'PwrCfgCmd' during its initialization is never read
drivers/staging/rtl8723bs/os_dep/ioctl_linux.c:374:7: warning: Value
stored to 'ie_ptr' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a cleanup patch to fix line length issue found
by checkpatch.pl script.
In this patch, lines 186, 192 and 199 have been wrapped.
Signed-off-by: Eujon Sellers <eujon.sellers@gmail.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The logic of the original commit 4d99b2581eff ("staging: lustre: avoid
intensive reconnecting for ko2iblnd") was assumed conditional free of
struct kib_conn if the second argument free_conn in function
kiblnd_destroy_conn(struct kib_conn *conn, bool free_conn) is true.
But this hunk of code was dropped from original commit. As result the logic
works wrong and current code use struct kib_conn after free.
> drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c
> 3317 kiblnd_destroy_conn(conn, !peer);
> ^^^^ Freed always (but should be conditionally)
> 3318
> 3319 spin_lock_irqsave(lock, flags);
> 3320 if (!peer)
> 3321 continue;
> 3322
> 3323 conn->ibc_peer = peer;
> ^^^^^^^^^^^^^^ Use after free
> 3324 if (peer->ibp_reconnected < KIB_RECONN_HIGH_RACE)
> 3325 list_add_tail(&conn->ibc_list,
> ^^^^^^^^^^^^^^ Use after free
> 3326 &kiblnd_data.kib_reconn_list);
> 3327 else
> 3328 list_add_tail(&conn->ibc_list,
> ^^^^^^^^^^^^^^ Use after free
> 3329 &kiblnd_data.kib_reconn_wait);
To avoid confusion this fix moved the freeing a struct kib_conn outside of
the function kiblnd_destroy_conn() and free as it was intended in original
commit.
Cc: <stable@vger.kernel.org> # v4.6
Fixes: 4d99b2581eff ("staging: lustre: avoid intensive reconnecting for ko2iblnd")
Signed-off-by: Dmitry Eremin <Dmitry.Eremin@intel.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
