summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-01-16ath9k: Fix an operator typo in REG_DOMAIN_2GHZ_MASKJouni Malinen
Incorrect operator causes the REG_DOMAIN_2GHZ_MASK to be zero which surely was not the goal of this definition. Mask out the 11a flags correctly. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-16ath9k: Fix an operator typo in phy rate validationJouni Malinen
This was not supposed to be a bitwise AND operation, but a check of two separate conditions. Anyway, the old code happened to result in the same behavior, so this is just changing the code to be easier to understand and also to keep sparse from warning about dubious operators. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-16libertas: Fix alignment issues in libertas coreAndrey Yurovsky
Data structures that come over the wire from the WLAN firmware must be packed. This fixes alignment problems on the blackfin architecture and, reportedly, on the AVR32. This is a replacement for the previous version of this patch which had also explicitly used get_unaligned_ macros. As Johannes Berg pointed out, these macros were unnecessary. Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Signed-off-by: Colin McCabe <colin@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-16p54: fix oops caused by bad eepromsChristian Lamparter
This patch fixes a bug that could occur, if it the eeprom is incomplete or partly corrupted. BUG: unable to handle kernel NULL pointer dereference at 00000008 IP: p54_assign_address+0x108/0x15d [p54common] Oops: 0002 [#1] SMP Pid: 12988, comm: phy1 Tainted: P W 2.6.28-rc6-wl #3 RIP: 0010: p54_assign_address+0x108/0x15d [p54common] [...] Call Trace: p54_alloc_skb+0xa3/0xc0 [p54common] p54_scan+0x37/0x204 [p54common] [...] Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-16IPoIB: Do not print error messages for multicast join retriesYossi Etigin
When IPoIB tries to join a multicast group, and the SA module's SM address handle is NULL (because of an SM change, etc), the join returns with -EAGAIN status. In that case, don't print an error message unless multicast debugging is enabled. Signed-off-by: Yossi Etigin <yosefe@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-01-16PCI PM: Restore standard config registers of all devices earlyRafael J. Wysocki
There is a problem in our handling of suspend-resume of PCI devices that many of them have their standard config registers restored with interrupts enabled and they are put into the full power state with interrupts enabled as well. This may lead to the following scenario: * an interrupt vector is shared between two or more devices * one device is resumed earlier and generates an interrupt * the interrupt handler of another device tries to handle it and attempts to access the device the config space of which hasn't been restored yet and/or which still is in a low power state * the system crashes as a result To prevent this from happening we should restore the standard configuration registers of all devices with interrupts disabled and we should put them into the D0 power state right after that. Unfortunately, this cannot be done using the existing pci_set_power_state(), because it can sleep. Also, to do it we have to make sure that the config spaces of all devices were actually saved during suspend. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-16IB/mlx4: Fix memory ordering problem when posting LSO sendsRoland Dreier
The current work request posting code writes the LSO segment before writing any data segments. This leaves a window where the LSO segment overwrites the stamping in one cacheline that the HCA prefetches before the rest of the cacheline is filled with the correct data segments. When the HCA processes this work request, a local protection error may result. Fix this by saving the LSO header size field off and writing it only after all data segments are written. This fix is a cleaned-up version of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>. This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>. Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-01-16Merge branch 'release' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits) ACPI PCI hotplug: harden against panic regression ACPI: rename main.c to sleep.c dell-laptop: move to drivers/platform/x86/ from drivers/misc/ eeepc-laptop: enable Bluetooth ACPI details ACPI: fix ACPI_FADT_S4_RTC_WAKE comment kprobes: check CONFIG_FREEZER instead of CONFIG_PM PM: Fix freezer compilation if PM_SLEEP is unset thermal fixup for broken BIOS which has invalid trip points. ACPI: EC: Don't trust ECDT tables from ASUS ACPI: EC: Limit workaround for ASUS notebooks even more ACPI: thinkpad-acpi: bump up version to 0.22 ACPI: thinkpad-acpi: handle HKEY event 6030 ACPI: thinkpad-acpi: clean-up fan subdriver quirk ACPI: thinkpad-acpi: start the event hunt season ACPI: thinkpad-acpi: handle HKEY thermal and battery alarms ACPI: thinkpad-acpi: clean up hotkey_notify() ACPI: thinkpad-acpi: use killable instead of interruptible mutexes ACPI: thinkpad-acpi: add UWB radio support ACPI: thinkpad-acpi: preserve radio state across shutdown ACPI: thinkpad-acpi: resume with radios disabled ...
2009-01-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: netxen: include ipv6.h (fixes build failure) netxen: avoid invalid iounmap
2009-01-16PCI/MSI: bugfix/utilize for msi_capability_init()Hidetoshi Seto
This patch fix a following bug and does a cleanup. bug: commit 5993760f7fc75b77e4701f1e56dc84c0d6cf18d5 had a wrong change (since is_64 is boolean[0|1]): - pci_write_config_dword(dev, - msi_mask_bits_reg(pos, is_64bit_address(control)), - maskbits); + pci_write_config_dword(dev, entry->msi_attrib.is_64, maskbits); utilize: Unify separated if (entry->msi_attrib.maskbit) statements. Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Acked-by: "Jike Song" <albcamus@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-16ACPI PCI hotplug: harden against panic regressionJames Bottomley
ACPI hotplug panic with current git head http://lkml.org/lkml/2009/1/10/136 Rather than reverting the entire commit that causes the crash: e8c331e963c58b83db24b7d0e39e8c07f687dbc6 "PCI hotplug: introduce functions for ACPI slot detection" simply harden against it while the changes to the hotplug code on this particularl machine are understood. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Len Brown <len.brown@intel.com>
2009-01-16Merge branch 'misc' into releaseLen Brown
2009-01-16Merge branch 'thinkpad-acpi' into releaseLen Brown
2009-01-16Merge branches 'bugzilla-11884' and 'bugzilla-8544' into releaseLen Brown
2009-01-16ACPI: rename main.c to sleep.cLen Brown
Signed-off-by: Len Brown <len.brown@intel.com>
2009-01-16dell-laptop: move to drivers/platform/x86/ from drivers/misc/Len Brown
Signed-off-by: Len Brown <len.brown@intel.com>
2009-01-16eeepc-laptop: enable Bluetooth ACPI detailsJonathan McDowell
Although rfkill support for the EEE bluetooth device has been added to 2.6.28-rc the appropriate ACPI accessor definitions were not added, so the support was non functional. The patch below adds the get and set accessors and has been verified to work on an EEE 901. Signed-off-by: Jonathan McDowell <noodles@earth.li> Acked-by: Matthew Garrett <mjg@redhat.com> Acked-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com>
2009-01-16thermal fixup for broken BIOS which has invalid trip points.Zhang Rui
ACPI thermal driver only re-evaluate VALID trip points. For the broken BIOS show in http://bugzilla.kernel.org/show_bug.cgi?id=8544 the active[0] is set to invalid at boot time and it will not be re-evaluated again. We can still get a single warning message at boot time. http://marc.info/?l=linux-kernel&m=120496222629983&w=2 http://bugzilla.kernel.org/show_bug.cgi?id=12203 Signed-off-by: Zhang Rui<rui.zhang@intel.com> Tested-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Len Brown <len.brown@intel.com>
2009-01-16netxen: include ipv6.h (fixes build failure)Dhananjay Phadke
Fixes a build error in absence of CONFIG_IPV6: drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr' drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->' Reported-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-16ACPI: EC: Don't trust ECDT tables from ASUSAlexey Starikovskiy
http://bugzilla.kernel.org/show_bug.cgi?id=9399 http://bugzilla.kernel.org/show_bug.cgi?id=11880 Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
2009-01-16netxen: avoid invalid iounmapDhananjay Phadke
For NX3031 only one I/O range is mapped, so unmapping other two which are used by older chips, causes this warning on ppc64. "Attempt to iounmap early bolted mapping at 0x0000000000000000" Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-16ACPI: EC: Limit workaround for ASUS notebooks even moreAlexey Starikovskiy
References: http://bugzilla.kernel.org/show_bug.cgi?id=11884 Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
2009-01-16Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: serial: Add 16850 uart type support to OF uart driver hvc_console: Remove tty->low_latency powerpc: Get the number of SLBs from "slb-size" property powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/video powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsi powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3 powerpc/ps3: Printing fixups for l64 to ll64 conversion sound/ppc powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/char powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/block powerpc/ps3: Printing fixups for l64 to ll64 conversion arch/powerpc powerpc/ps3: ps3_repository_read_mm_info() takes u64 * arguments powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs powerpc/ps3: The lv1_ routines have u64 parameters powerpc/ps3: Use dma_addr_t down through the stack powerpc/ps3: set_dabr() takes an unsigned long powerpc: Cleanup from l64 to ll64 change drivers/scsi
2009-01-16Merge branch 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: sata_fsl: Return non-zero on error in probe() drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build libata: New driver for OCTEON SOC Compact Flash interface (v7). libata: Add another column to the ata_timing table. sata_via: Add VT8261 support pata_atiixp: update port enabledness test handling [libata] get-identity ioctl: Fix use of invalid memory pointer
2009-01-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] Skip deleted devices in __scsi_device_lookup_by_target() [SCSI] Add SUN Universal Xport to no attach blacklist [SCSI] iscsi_tcp: make padbuf non-static [SCSI] mpt fusion: Add Firmware debug support [SCSI] mpt fusion: Add separate msi enable disable for FC,SPI,SAS [SCSI] mpt fusion: Update MPI Headers to version 01.05.19 [SCSI] qla2xxx: Fix ISP restart bug in multiq code
2009-01-16Merge branch 'drm-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6 * 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/i915: lock correct mutex around object unreference. drm/i915: add support for physical memory objects drm/i915: make LVDS fixed mode a preferred mode drm: handle depth & bpp changes correctly drm: initial KMS config fixes drm/i915: setup sarea properly in master_priv drm/i915: set vblank enabled flag correctly across IRQ install/uninstall drm/i915: don't enable vblanks on disabled pipes
2009-01-16Revert "PCI PM: Register power state of devices during initialization"Linus Torvalds
This reverts commit 98e6e286d7b01deb7453b717aa38ebb69d6cefc0, as Yinghai Lu reports that it breaks kexec with at least the e1000 and e1000e drivers. The reason is that the shutdown sequence puts the hardware into D3 sleep, and the commit causes us to claim that it then is in D0 (running) state just because we don't understand the PM capabilities. Which then later makes "pci_set_power_state()" not do anything, and the device never wakes up properly and just returns 0xff to everything. Reported-by: Yinghai Lu <yinghai@kernel.org> Acked-by: From: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jesse Barnes <jesse.barnes@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-16sata_fsl: Return non-zero on error in probe()Michal Sojka
while I was looking over kernel sources I've found this small bug. Formerly, zero was returned even if an error happened. Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha buildAndrew Morton
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16libata: New driver for OCTEON SOC Compact Flash interface (v7).David Daney
Cavium OCTEON processor support was recently merged, so now we have this CF driver for your consideration. Most OCTEON variants have *no* DMA or interrupt support on the CF interface so for these, only PIO is supported. Although if DMA is available, we do take advantage of it. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16libata: Add another column to the ata_timing table.David Daney
The forthcoming OCTEON SOC Compact Flash driver needs an additional timing value that was not available in the ata_timing table. I add a new column for dmack_hold time. The values were obtained from the Compact Flash specification Rev 4.1. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16sata_via: Add VT8261 supportJosephChan@via.com.tw
Signed-off-by: Joseph Chan <josephchan@via.com.tw> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16pata_atiixp: update port enabledness test handlingTejun Heo
Port enabledness test fits much better into init_one() instead of pre_reset(). The reason why these tests are in pre_reset() is purely historical at this point. Move it to init_one(). This will help further changes. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16[libata] get-identity ioctl: Fix use of invalid memory pointerJeff Garzik
for SAS drivers. Caught by Ke Wei (and team?) at Marvell. Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the general trend. Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16drm/i915: lock correct mutex around object unreference.Dave Airlie
This makes sure the mutex is held around the unreference. Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-01-16drm/i915: add support for physical memory objectsDave Airlie
This is an initial patch to do support for objects which needs physical contiguous main ram, cursors and overlay registers on older chipsets. These objects are bound on cursor bin, like pinning, and we copy the data to/from the backing store object into the real one on attach/detach. notes: possible over the top in attach/detach operations. no overlay support yet. Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-01-16drm/i915: make LVDS fixed mode a preferred modeJesse Barnes
The detected fixed panel mode really is preferred, so mark it as such and add it to the LVDS connector mode list. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
2009-01-16drm: handle depth & bpp changes correctlyJesse Barnes
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
2009-01-16drm: initial KMS config fixesJesse Barnes
When mode setting is first initialized, the driver will call into drm_helper_initial_config() to set up an initial output and framebuffer configuration. This routine is responsible for probing the available connectors, encoders, and crtcs, looking for modes and putting together something reasonable (where reasonable is defined as "allows kernel messages to be visible on as many displays as possible"). However, the code was a bit too aggressive in setting default modes when none were found on a given connector. Even if some connectors had modes, any connectors found lacking modes would have the default 800x600 mode added to their mode list, which in some cases could cause problems later down the line. In my case, the LVDS was perfectly available, but the initial config code added 800x600 modes to both of the detected but unavailable HDMI connectors (which are on my non-existent docking station). This ended up preventing later code from setting a mode on my LVDS, which is bad. This patch fixes that behavior by making the initial config code walk through the connectors first, counting the available modes, before it decides to add any default modes to a possibly connected output. It also fixes the logic in drm_target_preferred() that was causing zeroed out modes to be set as the preferred mode for a given connector, even if no modes were available. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
2009-01-15fsldma: print correct IRQ on mpc83xxPeter Korsgaard
The mpc83xx variant uses a shared IRQ for all channels, so the individual channel nodes don't have an interrupt property. Fix the code to print the controller IRQ instead if there isn't any for the channel. Acked-by: Timur Tabi <timur@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-01-16serial: Add 16850 uart type support to OF uart driverMatthias Fuchs
This patch adds support for "ns16850" as supported value of the compatible node in flat device tree uart descriptions. This is needed for example when you have a XR16C2850 uart connected to a PPC405's external bus controller. Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-16hvc_console: Remove tty->low_latencyHendrik Brueckner
This patch removes the tty->low_latency setting. For irq based hvc_console backends the tty->low_latency must be set to 0, because the tty_flip_buffer_push() function must not be called from IRQ context (see drivers/char/tty_buffer.c). For polled backends, the low_latency setting causes the bug trace below, because tty_flip_buffer_push() is called within an atomic context and subsequent calls might sleep due to mutex_lock. BUG: sleeping function called from invalid context at /root/cvs/linux-2.6.git/kernel/mutex.c:207 in_atomic(): 1, irqs_disabled(): 0, pid: 748, name: khvcd 1 lock held by khvcd/748: #0: (hvc_structs_lock){--..}, at: [<00000000002ceb50>] khvcd+0x58/0x12c CPU: 0 Not tainted 2.6.29-rc1git #29 Process khvcd (pid: 748, task: 000000002fb9a480, ksp: 000000002f66bd78) 070000000000000a 000000002f66ba00 0000000000000002 (null) 000000002f66baa0 000000002f66ba18 000000002f66ba18 0000000000104f08 ffffffffffffc000 000000002f66bd78 (null) (null) 000000002f66ba00 000000000000000c 000000002f66ba00 000000002f66ba70 0000000000466af8 0000000000104f08 000000002f66ba00 000000002f66ba50 Call Trace: ([<0000000000104e7c>] show_trace+0x138/0x158) [<0000000000104f62>] show_stack+0xc6/0xf8 [<0000000000105740>] dump_stack+0xb0/0xc0 [<000000000013144a>] __might_sleep+0x14e/0x17c [<000000000045e226>] mutex_lock_nested+0x42/0x3b4 [<00000000002c443e>] echo_char_raw+0x3a/0x9c [<00000000002c688c>] n_tty_receive_buf+0x1154/0x1208 [<00000000002ca0a2>] flush_to_ldisc+0x152/0x220 [<00000000002ca1da>] tty_flip_buffer_push+0x6a/0x90 [<00000000002cea74>] hvc_poll+0x244/0x2c8 [<00000000002ceb68>] khvcd+0x70/0x12c [<000000000015bbd0>] kthread+0x68/0xa0 [<0000000000109d5a>] kernel_thread_starter+0x6/0xc [<0000000000109d54>] kernel_thread_starter+0x0/0xc 1 lock held by khvcd/748: #0: (hvc_structs_lock){--..}, at: [<00000000002ceb50>] khvcd+0x58/0x12c Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-16powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/videoStephen Rothwell
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-16powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsiStephen Rothwell
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-16powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3Stephen Rothwell
Also some min -> mint_t conversion. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-16powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/charStephen Rothwell
Also a couple of min -> min_t changes. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-16powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/blockStephen Rothwell
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-16powerpc/ps3: The lv1_ routines have u64 parametersStephen Rothwell
We just fix up the reference parameters as the others are dealt with by arithmetic promotion rules and don't cause warnings. This removes warnings like this: arch/powerpc/platforms/ps3/interrupt.c:327: warning: passing argument 1 of 'lv1_construct_event_receive_port' from incompatible pointer type Also, these: drivers/ps3/ps3-vuart.c:462: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type drivers/ps3/ps3-vuart.c:592: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-16powerpc: Cleanup from l64 to ll64 change drivers/scsiStephen Rothwell
This is a powerpc specific driver. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-15mlx4_core: Fix min() warningAndrew Morton
Fix drivers/net/mlx4/profile.c: In function `mlx4_make_profile': drivers/net/mlx4/profile.c:110: warning: comparison of distinct pointer types lacks a cast This happened because num_possible_cpus() was secretly changed by commit ae7a47e7 ("cpumask: make cpumask.h eat its own dogfood.") from returning "int" to (now) returning "unsigned int". I think that was a good change, so we should just swallow the fallout. Cc: "David S. Miller" <davem@davemloft.net> Cc: Roland Dreier <rolandd@cisco.com> Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Cc: Jack Morgenstein <jackm@dev.mellanox.co.il> Cc: Vladimir Sokolovsky <vlad@mellanox.co.il> Cc: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Roland Dreier <rolandd@cisco.com>
generated by cgit (git 2.34.1) at 2025-09-14 17:06:44 +0000